diff --git a/drivers/serial/amba-pl011.c b/drivers/serial/amba-pl011.c
new file mode 100644
index 0000000..ff658a8
--- /dev/null
+++ b/drivers/serial/amba-pl011.c
@@ -0,0 +1,869 @@
+/*
+ *  linux/drivers/char/amba.c
+ *
+ *  Driver for AMBA serial ports
+ *
+ *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ *  Copyright 1999 ARM Limited
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ *  $Id: amba.c,v 1.41 2002/07/28 10:03:27 rmk Exp $
+ *
+ * This is a generic driver for ARM AMBA-type serial ports.  They
+ * have a lot of 16550-like features, but are not register compatible.
+ * Note that although they do have CTS, DCD and DSR inputs, they do
+ * not have an RI input, nor do they have DTR or RTS outputs.  If
+ * required, these have to be supplied via some other means (eg, GPIO)
+ * and hooked into this driver.
+ */
+#include <linux/config.h>
+
+#if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/hardware/amba.h>
+#include <asm/hardware/clock.h>
+#include <asm/hardware/amba_serial.h>
+
+#define UART_NR			14
+
+#define SERIAL_AMBA_MAJOR	204
+#define SERIAL_AMBA_MINOR	64
+#define SERIAL_AMBA_NR		UART_NR
+
+#define AMBA_ISR_PASS_LIMIT	256
+
+#define UART_DUMMY_RSR_RX	256
+
+/*
+ * We wrap our port structure around the generic uart_port.
+ */
+struct uart_amba_port {
+	struct uart_port	port;
+	struct clk		*clk;
+	unsigned int		im;	/* interrupt mask */
+	unsigned int		old_status;
+};
+
+static void pl011_stop_tx(struct uart_port *port, unsigned int tty_stop)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+	uap->im &= ~UART011_TXIM;
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+}
+
+static void pl011_start_tx(struct uart_port *port, unsigned int tty_start)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+	uap->im |= UART011_TXIM;
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+}
+
+static void pl011_stop_rx(struct uart_port *port)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+	uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
+		     UART011_PEIM|UART011_BEIM|UART011_OEIM);
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+}
+
+static void pl011_enable_ms(struct uart_port *port)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+	uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+}
+
+static void
+#ifdef SUPPORT_SYSRQ
+pl011_rx_chars(struct uart_amba_port *uap, struct pt_regs *regs)
+#else
+pl011_rx_chars(struct uart_amba_port *uap)
+#endif
+{
+	struct tty_struct *tty = uap->port.info->tty;
+	unsigned int status, ch, flag, rsr, max_count = 256;
+
+	status = readw(uap->port.membase + UART01x_FR);
+	while ((status & UART01x_FR_RXFE) == 0 && max_count--) {
+		if (tty->flip.count >= TTY_FLIPBUF_SIZE) {
+			if (tty->low_latency)
+				tty_flip_buffer_push(tty);
+			/*
+			 * If this failed then we will throw away the
+			 * bytes but must do so to clear interrupts
+			 */
+		}
+
+		ch = readw(uap->port.membase + UART01x_DR);
+		flag = TTY_NORMAL;
+		uap->port.icount.rx++;
+
+		/*
+		 * Note that the error handling code is
+		 * out of the main execution path
+		 */
+		rsr = readw(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+		if (rsr & UART01x_RSR_ANY) {
+			if (rsr & UART01x_RSR_BE) {
+				rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
+				uap->port.icount.brk++;
+				if (uart_handle_break(&uap->port))
+					goto ignore_char;
+			} else if (rsr & UART01x_RSR_PE)
+				uap->port.icount.parity++;
+			else if (rsr & UART01x_RSR_FE)
+				uap->port.icount.frame++;
+			if (rsr & UART01x_RSR_OE)
+				uap->port.icount.overrun++;
+
+			rsr &= uap->port.read_status_mask;
+
+			if (rsr & UART01x_RSR_BE)
+				flag = TTY_BREAK;
+			else if (rsr & UART01x_RSR_PE)
+				flag = TTY_PARITY;
+			else if (rsr & UART01x_RSR_FE)
+				flag = TTY_FRAME;
+		}
+
+		if (uart_handle_sysrq_char(&uap->port, ch, regs))
+			goto ignore_char;
+
+		if ((rsr & uap->port.ignore_status_mask) == 0) {
+			tty_insert_flip_char(tty, ch, flag);
+		}
+		if ((rsr & UART01x_RSR_OE) &&
+		    tty->flip.count < TTY_FLIPBUF_SIZE) {
+			/*
+			 * Overrun is special, since it's reported
+			 * immediately, and doesn't affect the current
+			 * character
+			 */
+			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+		}
+	ignore_char:
+		status = readw(uap->port.membase + UART01x_FR);
+	}
+	tty_flip_buffer_push(tty);
+	return;
+}
+
+static void pl011_tx_chars(struct uart_amba_port *uap)
+{
+	struct circ_buf *xmit = &uap->port.info->xmit;
+	int count;
+
+	if (uap->port.x_char) {
+		writew(uap->port.x_char, uap->port.membase + UART01x_DR);
+		uap->port.icount.tx++;
+		uap->port.x_char = 0;
+		return;
+	}
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
+		pl011_stop_tx(&uap->port, 0);
+		return;
+	}
+
+	count = uap->port.fifosize >> 1;
+	do {
+		writew(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		uap->port.icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	} while (--count > 0);
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&uap->port);
+
+	if (uart_circ_empty(xmit))
+		pl011_stop_tx(&uap->port, 0);
+}
+
+static void pl011_modem_status(struct uart_amba_port *uap)
+{
+	unsigned int status, delta;
+
+	status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+	delta = status ^ uap->old_status;
+	uap->old_status = status;
+
+	if (!delta)
+		return;
+
+	if (delta & UART01x_FR_DCD)
+		uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
+
+	if (delta & UART01x_FR_DSR)
+		uap->port.icount.dsr++;
+
+	if (delta & UART01x_FR_CTS)
+		uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS);
+
+	wake_up_interruptible(&uap->port.info->delta_msr_wait);
+}
+
+static irqreturn_t pl011_int(int irq, void *dev_id, struct pt_regs *regs)
+{
+	struct uart_amba_port *uap = dev_id;
+	unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
+	int handled = 0;
+
+	spin_lock(&uap->port.lock);
+
+	status = readw(uap->port.membase + UART011_MIS);
+	if (status) {
+		do {
+			writew(status & ~(UART011_TXIS|UART011_RTIS|
+					  UART011_RXIS),
+			       uap->port.membase + UART011_ICR);
+
+			if (status & (UART011_RTIS|UART011_RXIS))
+#ifdef SUPPORT_SYSRQ
+				pl011_rx_chars(uap, regs);
+#else
+				pl011_rx_chars(uap);
+#endif
+			if (status & (UART011_DSRMIS|UART011_DCDMIS|
+				      UART011_CTSMIS|UART011_RIMIS))
+				pl011_modem_status(uap);
+			if (status & UART011_TXIS)
+				pl011_tx_chars(uap);
+
+			if (pass_counter-- == 0)
+				break;
+
+			status = readw(uap->port.membase + UART011_MIS);
+		} while (status != 0);
+		handled = 1;
+	}
+
+	spin_unlock(&uap->port.lock);
+
+	return IRQ_RETVAL(handled);
+}
+
+static unsigned int pl01x_tx_empty(struct uart_port *port)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned int status = readw(uap->port.membase + UART01x_FR);
+	return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
+}
+
+static unsigned int pl01x_get_mctrl(struct uart_port *port)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned int result = 0;
+	unsigned int status = readw(uap->port.membase + UART01x_FR);
+
+#define BIT(uartbit, tiocmbit)		\
+	if (status & uartbit)		\
+		result |= tiocmbit
+
+	BIT(UART01x_FR_DCD, TIOCM_CAR);
+	BIT(UART01x_FR_DSR, TIOCM_DSR);
+	BIT(UART01x_FR_CTS, TIOCM_CTS);
+	BIT(UART011_FR_RI, TIOCM_RNG);
+#undef BIT
+	return result;
+}
+
+static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned int cr;
+
+	cr = readw(uap->port.membase + UART011_CR);
+
+#define	BIT(tiocmbit, uartbit)		\
+	if (mctrl & tiocmbit)		\
+		cr |= uartbit;		\
+	else				\
+		cr &= ~uartbit
+
+	BIT(TIOCM_RTS, UART011_CR_RTS);
+	BIT(TIOCM_DTR, UART011_CR_DTR);
+	BIT(TIOCM_OUT1, UART011_CR_OUT1);
+	BIT(TIOCM_OUT2, UART011_CR_OUT2);
+	BIT(TIOCM_LOOP, UART011_CR_LBE);
+#undef BIT
+
+	writew(cr, uap->port.membase + UART011_CR);
+}
+
+static void pl011_break_ctl(struct uart_port *port, int break_state)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned long flags;
+	unsigned int lcr_h;
+
+	spin_lock_irqsave(&uap->port.lock, flags);
+	lcr_h = readw(uap->port.membase + UART011_LCRH);
+	if (break_state == -1)
+		lcr_h |= UART01x_LCRH_BRK;
+	else
+		lcr_h &= ~UART01x_LCRH_BRK;
+	writew(lcr_h, uap->port.membase + UART011_LCRH);
+	spin_unlock_irqrestore(&uap->port.lock, flags);
+}
+
+static int pl011_startup(struct uart_port *port)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned int cr;
+	int retval;
+
+	/*
+	 * Try to enable the clock producer.
+	 */
+	retval = clk_enable(uap->clk);
+	if (retval)
+		goto out;
+
+	uap->port.uartclk = clk_get_rate(uap->clk);
+
+	/*
+	 * Allocate the IRQ
+	 */
+	retval = request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap);
+	if (retval)
+		goto clk_dis;
+
+	writew(UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
+	       uap->port.membase + UART011_IFLS);
+
+	/*
+	 * Provoke TX FIFO interrupt into asserting.
+	 */
+	cr = UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_LBE;
+	writew(cr, uap->port.membase + UART011_CR);
+	writew(0, uap->port.membase + UART011_FBRD);
+	writew(1, uap->port.membase + UART011_IBRD);
+	writew(0, uap->port.membase + UART011_LCRH);
+	writew(0, uap->port.membase + UART01x_DR);
+	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
+		barrier();
+
+	cr = UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
+	writew(cr, uap->port.membase + UART011_CR);
+
+	/*
+	 * initialise the old status of the modem signals
+	 */
+	uap->old_status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+	/*
+	 * Finally, enable interrupts
+	 */
+	spin_lock_irq(&uap->port.lock);
+	uap->im = UART011_RXIM | UART011_RTIM;
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+	spin_unlock_irq(&uap->port.lock);
+
+	return 0;
+
+ clk_dis:
+	clk_disable(uap->clk);
+ out:
+	return retval;
+}
+
+static void pl011_shutdown(struct uart_port *port)
+{
+	struct uart_amba_port *uap = (struct uart_amba_port *)port;
+	unsigned long val;
+
+	/*
+	 * disable all interrupts
+	 */
+	spin_lock_irq(&uap->port.lock);
+	uap->im = 0;
+	writew(uap->im, uap->port.membase + UART011_IMSC);
+	writew(0xffff, uap->port.membase + UART011_ICR);
+	spin_unlock_irq(&uap->port.lock);
+
+	/*
+	 * Free the interrupt
+	 */
+	free_irq(uap->port.irq, uap);
+
+	/*
+	 * disable the port
+	 */
+	writew(UART01x_CR_UARTEN | UART011_CR_TXE, uap->port.membase + UART011_CR);
+
+	/*
+	 * disable break condition and fifos
+	 */
+	val = readw(uap->port.membase + UART011_LCRH);
+	val &= ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN);
+	writew(val, uap->port.membase + UART011_LCRH);
+
+	/*
+	 * Shut down the clock producer
+	 */
+	clk_disable(uap->clk);
+}
+
+static void
+pl011_set_termios(struct uart_port *port, struct termios *termios,
+		     struct termios *old)
+{
+	unsigned int lcr_h, old_cr;
+	unsigned long flags;
+	unsigned int baud, quot;
+
+	/*
+	 * Ask the core to calculate the divisor for us.
+	 */
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+	quot = port->uartclk * 4 / baud;
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		lcr_h = UART01x_LCRH_WLEN_5;
+		break;
+	case CS6:
+		lcr_h = UART01x_LCRH_WLEN_6;
+		break;
+	case CS7:
+		lcr_h = UART01x_LCRH_WLEN_7;
+		break;
+	default: // CS8
+		lcr_h = UART01x_LCRH_WLEN_8;
+		break;
+	}
+	if (termios->c_cflag & CSTOPB)
+		lcr_h |= UART01x_LCRH_STP2;
+	if (termios->c_cflag & PARENB) {
+		lcr_h |= UART01x_LCRH_PEN;
+		if (!(termios->c_cflag & PARODD))
+			lcr_h |= UART01x_LCRH_EPS;
+	}
+	if (port->fifosize > 1)
+		lcr_h |= UART01x_LCRH_FEN;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	port->read_status_mask = UART01x_RSR_OE;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= UART01x_RSR_BE;
+
+	/*
+	 * Characters to ignore
+	 */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= UART01x_RSR_BE;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns too (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= UART01x_RSR_OE;
+	}
+
+	/*
+	 * Ignore all characters if CREAD is not set.
+	 */
+	if ((termios->c_cflag & CREAD) == 0)
+		port->ignore_status_mask |= UART_DUMMY_RSR_RX;
+
+	if (UART_ENABLE_MS(port, termios->c_cflag))
+		pl011_enable_ms(port);
+
+	/* first, disable everything */
+	old_cr = readw(port->membase + UART011_CR);
+	writew(0, port->membase + UART011_CR);
+
+	/* Set baud rate */
+	writew(quot & 0x3f, port->membase + UART011_FBRD);
+	writew(quot >> 6, port->membase + UART011_IBRD);
+
+	/*
+	 * ----------v----------v----------v----------v-----
+	 * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
+	 * ----------^----------^----------^----------^-----
+	 */
+	writew(lcr_h, port->membase + UART011_LCRH);
+	writew(old_cr, port->membase + UART011_CR);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *pl011_type(struct uart_port *port)
+{
+	return port->type == PORT_AMBA ? "AMBA/PL011" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'
+ */
+static void pl010_release_port(struct uart_port *port)
+{
+	release_mem_region(port->mapbase, SZ_4K);
+}
+
+/*
+ * Request the memory region(s) being used by 'port'
+ */
+static int pl010_request_port(struct uart_port *port)
+{
+	return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
+			!= NULL ? 0 : -EBUSY;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void pl010_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_AMBA;
+		pl010_request_port(port);
+	}
+}
+
+/*
+ * verify the new serial_struct (for TIOCSSERIAL).
+ */
+static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	int ret = 0;
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
+		ret = -EINVAL;
+	if (ser->irq < 0 || ser->irq >= NR_IRQS)
+		ret = -EINVAL;
+	if (ser->baud_base < 9600)
+		ret = -EINVAL;
+	return ret;
+}
+
+static struct uart_ops amba_pl011_pops = {
+	.tx_empty	= pl01x_tx_empty,
+	.set_mctrl	= pl011_set_mctrl,
+	.get_mctrl	= pl01x_get_mctrl,
+	.stop_tx	= pl011_stop_tx,
+	.start_tx	= pl011_start_tx,
+	.stop_rx	= pl011_stop_rx,
+	.enable_ms	= pl011_enable_ms,
+	.break_ctl	= pl011_break_ctl,
+	.startup	= pl011_startup,
+	.shutdown	= pl011_shutdown,
+	.set_termios	= pl011_set_termios,
+	.type		= pl011_type,
+	.release_port	= pl010_release_port,
+	.request_port	= pl010_request_port,
+	.config_port	= pl010_config_port,
+	.verify_port	= pl010_verify_port,
+};
+
+static struct uart_amba_port *amba_ports[UART_NR];
+
+#ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE
+
+static inline void
+pl011_console_write_char(struct uart_amba_port *uap, char ch)
+{
+	unsigned int status;
+
+	do {
+		status = readw(uap->port.membase + UART01x_FR);
+	} while (status & UART01x_FR_TXFF);
+	writew(ch, uap->port.membase + UART01x_DR);
+}
+
+static void
+pl011_console_write(struct console *co, const char *s, unsigned int count)
+{
+	struct uart_amba_port *uap = amba_ports[co->index];
+	unsigned int status, old_cr, new_cr;
+	int i;
+
+	clk_enable(uap->clk);
+
+	/*
+	 *	First save the CR then disable the interrupts
+	 */
+	old_cr = readw(uap->port.membase + UART011_CR);
+	new_cr = old_cr & ~UART011_CR_CTSEN;
+	new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
+	writew(new_cr, uap->port.membase + UART011_CR);
+
+	/*
+	 *	Now, do each character
+	 */
+	for (i = 0; i < count; i++) {
+		pl011_console_write_char(uap, s[i]);
+		if (s[i] == '\n')
+			pl011_console_write_char(uap, '\r');
+	}
+
+	/*
+	 *	Finally, wait for transmitter to become empty
+	 *	and restore the TCR
+	 */
+	do {
+		status = readw(uap->port.membase + UART01x_FR);
+	} while (status & UART01x_FR_BUSY);
+	writew(old_cr, uap->port.membase + UART011_CR);
+
+	clk_disable(uap->clk);
+}
+
+static void __init
+pl011_console_get_options(struct uart_amba_port *uap, int *baud,
+			     int *parity, int *bits)
+{
+	if (readw(uap->port.membase + UART011_CR) & UART01x_CR_UARTEN) {
+		unsigned int lcr_h, ibrd, fbrd;
+
+		lcr_h = readw(uap->port.membase + UART011_LCRH);
+
+		*parity = 'n';
+		if (lcr_h & UART01x_LCRH_PEN) {
+			if (lcr_h & UART01x_LCRH_EPS)
+				*parity = 'e';
+			else
+				*parity = 'o';
+		}
+
+		if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
+			*bits = 7;
+		else
+			*bits = 8;
+
+		ibrd = readw(uap->port.membase + UART011_IBRD);
+		fbrd = readw(uap->port.membase + UART011_FBRD);
+
+		*baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd);
+	}
+}
+
+static int __init pl011_console_setup(struct console *co, char *options)
+{
+	struct uart_amba_port *uap;
+	int baud = 38400;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	/*
+	 * Check whether an invalid uart number has been specified, and
+	 * if so, search for the first available port that does have
+	 * console support.
+	 */
+	if (co->index >= UART_NR)
+		co->index = 0;
+	uap = amba_ports[co->index];
+
+	uap->port.uartclk = clk_get_rate(uap->clk);
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+	else
+		pl011_console_get_options(uap, &baud, &parity, &bits);
+
+	return uart_set_options(&uap->port, co, baud, parity, bits, flow);
+}
+
+extern struct uart_driver amba_reg;
+static struct console amba_console = {
+	.name		= "ttyAMA",
+	.write		= pl011_console_write,
+	.device		= uart_console_device,
+	.setup		= pl011_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &amba_reg,
+};
+
+#define AMBA_CONSOLE	(&amba_console)
+#else
+#define AMBA_CONSOLE	NULL
+#endif
+
+static struct uart_driver amba_reg = {
+	.owner			= THIS_MODULE,
+	.driver_name		= "ttyAMA",
+	.dev_name		= "ttyAMA",
+	.major			= SERIAL_AMBA_MAJOR,
+	.minor			= SERIAL_AMBA_MINOR,
+	.nr			= UART_NR,
+	.cons			= AMBA_CONSOLE,
+};
+
+static int pl011_probe(struct amba_device *dev, void *id)
+{
+	struct uart_amba_port *uap;
+	void __iomem *base;
+	int i, ret;
+
+	for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
+		if (amba_ports[i] == NULL)
+			break;
+
+	if (i == ARRAY_SIZE(amba_ports)) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	uap = kmalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
+	if (uap == NULL) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	base = ioremap(dev->res.start, PAGE_SIZE);
+	if (!base) {
+		ret = -ENOMEM;
+		goto free;
+	}
+
+	memset(uap, 0, sizeof(struct uart_amba_port));
+	uap->clk = clk_get(&dev->dev, "UARTCLK");
+	if (IS_ERR(uap->clk)) {
+		ret = PTR_ERR(uap->clk);
+		goto unmap;
+	}
+
+	ret = clk_use(uap->clk);
+	if (ret)
+		goto putclk;
+
+	uap->port.dev = &dev->dev;
+	uap->port.mapbase = dev->res.start;
+	uap->port.membase = base;
+	uap->port.iotype = UPIO_MEM;
+	uap->port.irq = dev->irq[0];
+	uap->port.fifosize = 16;
+	uap->port.ops = &amba_pl011_pops;
+	uap->port.flags = UPF_BOOT_AUTOCONF;
+	uap->port.line = i;
+
+	amba_ports[i] = uap;
+
+	amba_set_drvdata(dev, uap);
+	ret = uart_add_one_port(&amba_reg, &uap->port);
+	if (ret) {
+		amba_set_drvdata(dev, NULL);
+		amba_ports[i] = NULL;
+		clk_unuse(uap->clk);
+ putclk:
+		clk_put(uap->clk);
+ unmap:
+		iounmap(base);
+ free:
+		kfree(uap);
+	}
+ out:
+	return ret;
+}
+
+static int pl011_remove(struct amba_device *dev)
+{
+	struct uart_amba_port *uap = amba_get_drvdata(dev);
+	int i;
+
+	amba_set_drvdata(dev, NULL);
+
+	uart_remove_one_port(&amba_reg, &uap->port);
+
+	for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
+		if (amba_ports[i] == uap)
+			amba_ports[i] = NULL;
+
+	iounmap(uap->port.membase);
+	clk_unuse(uap->clk);
+	clk_put(uap->clk);
+	kfree(uap);
+	return 0;
+}
+
+static struct amba_id pl011_ids[] __initdata = {
+	{
+		.id	= 0x00041011,
+		.mask	= 0x000fffff,
+	},
+	{ 0, 0 },
+};
+
+static struct amba_driver pl011_driver = {
+	.drv = {
+		.name	= "uart-pl011",
+	},
+	.id_table	= pl011_ids,
+	.probe		= pl011_probe,
+	.remove		= pl011_remove,
+};
+
+static int __init pl011_init(void)
+{
+	int ret;
+	printk(KERN_INFO "Serial: AMBA PL011 UART driver\n");
+
+	ret = uart_register_driver(&amba_reg);
+	if (ret == 0) {
+		ret = amba_driver_register(&pl011_driver);
+		if (ret)
+			uart_unregister_driver(&amba_reg);
+	}
+	return ret;
+}
+
+static void __exit pl011_exit(void)
+{
+	amba_driver_unregister(&pl011_driver);
+	uart_unregister_driver(&amba_reg);
+}
+
+module_init(pl011_init);
+module_exit(pl011_exit);
+
+MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
+MODULE_DESCRIPTION("ARM AMBA serial port driver");
+MODULE_LICENSE("GPL");