Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h
new file mode 100644
index 0000000..1800c0e7
--- /dev/null
+++ b/drivers/serial/crisv10.h
@@ -0,0 +1,137 @@
+/*
+ * serial.h: Arch-dep definitions for the Etrax100 serial driver.
+ *
+ * Copyright (C) 1998, 1999, 2000 Axis Communications AB
+ */
+
+#ifndef _ETRAX_SERIAL_H
+#define _ETRAX_SERIAL_H
+
+#include <linux/config.h>
+#include <linux/circ_buf.h>
+#include <asm/termios.h>
+
+/* Software state per channel */
+
+#ifdef __KERNEL__
+/*
+ * This is our internal structure for each serial port's state.
+ *
+ * Many fields are paralleled by the structure used by the serial_struct
+ * structure.
+ *
+ * For definitions of the flags field, see tty.h
+ */
+
+#define SERIAL_RECV_DESCRIPTORS 8
+
+struct etrax_recv_buffer {
+ struct etrax_recv_buffer *next;
+ unsigned short length;
+ unsigned char error;
+ unsigned char pad;
+
+ unsigned char buffer[0];
+};
+
+struct e100_serial {
+ int baud;
+ volatile u8 *port; /* R_SERIALx_CTRL */
+ u32 irq; /* bitnr in R_IRQ_MASK2 for dmaX_descr */
+
+ /* Output registers */
+ volatile u8 *oclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
+ volatile u32 *ofirstadr; /* adr to R_DMA_CHx_FIRST */
+ volatile u8 *ocmdadr; /* adr to R_DMA_CHx_CMD */
+ const volatile u8 *ostatusadr; /* adr to R_DMA_CHx_STATUS */
+
+ /* Input registers */
+ volatile u8 *iclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
+ volatile u32 *ifirstadr; /* adr to R_DMA_CHx_FIRST */
+ volatile u8 *icmdadr; /* adr to R_DMA_CHx_CMD */
+ volatile u32 *idescradr; /* adr to R_DMA_CHx_DESCR */
+
+ int flags; /* defined in tty.h */
+
+ u8 rx_ctrl; /* shadow for R_SERIALx_REC_CTRL */
+ u8 tx_ctrl; /* shadow for R_SERIALx_TR_CTRL */
+ u8 iseteop; /* bit number for R_SET_EOP for the input dma */
+ int enabled; /* Set to 1 if the port is enabled in HW config */
+
+ u8 dma_out_enabled:1; /* Set to 1 if DMA should be used */
+ u8 dma_in_enabled:1; /* Set to 1 if DMA should be used */
+
+ /* end of fields defined in rs_table[] in .c-file */
+ u8 uses_dma_in; /* Set to 1 if DMA is used */
+ u8 uses_dma_out; /* Set to 1 if DMA is used */
+ u8 forced_eop; /* a fifo eop has been forced */
+ int baud_base; /* For special baudrates */
+ int custom_divisor; /* For special baudrates */
+ struct etrax_dma_descr tr_descr;
+ struct etrax_dma_descr rec_descr[SERIAL_RECV_DESCRIPTORS];
+ int cur_rec_descr;
+
+ volatile int tr_running; /* 1 if output is running */
+
+ struct tty_struct *tty;
+ int read_status_mask;
+ int ignore_status_mask;
+ int x_char; /* xon/xoff character */
+ int close_delay;
+ unsigned short closing_wait;
+ unsigned short closing_wait2;
+ unsigned long event;
+ unsigned long last_active;
+ int line;
+ int type; /* PORT_ETRAX */
+ int count; /* # of fd on device */
+ int blocked_open; /* # of blocked opens */
+ struct circ_buf xmit;
+ struct etrax_recv_buffer *first_recv_buffer;
+ struct etrax_recv_buffer *last_recv_buffer;
+ unsigned int recv_cnt;
+ unsigned int max_recv_cnt;
+
+ struct work_struct work;
+ struct async_icount icount; /* error-statistics etc.*/
+ struct termios normal_termios;
+ struct termios callout_termios;
+#ifdef DECLARE_WAITQUEUE
+ wait_queue_head_t open_wait;
+ wait_queue_head_t close_wait;
+#else
+ struct wait_queue *open_wait;
+ struct wait_queue *close_wait;
+#endif
+
+ unsigned long char_time_usec; /* The time for 1 char, in usecs */
+ unsigned long flush_time_usec; /* How often we should flush */
+ unsigned long last_tx_active_usec; /* Last tx usec in the jiffies */
+ unsigned long last_tx_active; /* Last tx time in jiffies */
+ unsigned long last_rx_active_usec; /* Last rx usec in the jiffies */
+ unsigned long last_rx_active; /* Last rx time in jiffies */
+
+ int break_detected_cnt;
+ int errorcode;
+
+#ifdef CONFIG_ETRAX_RS485
+ struct rs485_control rs485; /* RS-485 support */
+#endif
+};
+
+/* this PORT is not in the standard serial.h. it's not actually used for
+ * anything since we only have one type of async serial-port anyway in this
+ * system.
+ */
+
+#define PORT_ETRAX 1
+
+/*
+ * Events are used to schedule things to happen at timer-interrupt
+ * time, instead of at rs interrupt time.
+ */
+#define RS_EVENT_WRITE_WAKEUP 0
+
+#endif /* __KERNEL__ */
+
+#endif /* !_ETRAX_SERIAL_H */