diff --git a/include/asm-i386/voyager.h b/include/asm-i386/voyager.h
new file mode 100644
index 0000000..aaf432d
--- /dev/null
+++ b/include/asm-i386/voyager.h
@@ -0,0 +1,521 @@
+/* Copyright (C) 1999,2001
+ *
+ * Author: J.E.J.Bottomley@HansenPartnership.com
+ *
+ * Standard include definitions for the NCR Voyager system */
+
+#undef	VOYAGER_DEBUG
+#undef	VOYAGER_CAT_DEBUG
+
+#ifdef VOYAGER_DEBUG
+#define VDEBUG(x)	printk x
+#else
+#define VDEBUG(x)
+#endif
+
+/* There are three levels of voyager machine: 3,4 and 5. The rule is
+ * if it's less than 3435 it's a Level 3 except for a 3360 which is
+ * a level 4.  A 3435 or above is a Level 5 */
+#define VOYAGER_LEVEL5_AND_ABOVE	0x3435
+#define VOYAGER_LEVEL4			0x3360
+
+/* The L4 DINO ASIC */
+#define VOYAGER_DINO			0x43
+
+/* voyager ports in standard I/O space */
+#define VOYAGER_MC_SETUP	0x96
+
+
+#define	VOYAGER_CAT_CONFIG_PORT			0x97
+#	define VOYAGER_CAT_DESELECT		0xff
+#define VOYAGER_SSPB_RELOCATION_PORT		0x98
+
+/* Valid CAT controller commands */
+/* start instruction register cycle */
+#define VOYAGER_CAT_IRCYC			0x01
+/* start data register cycle */
+#define VOYAGER_CAT_DRCYC			0x02
+/* move to execute state */
+#define VOYAGER_CAT_RUN				0x0F
+/* end operation */
+#define VOYAGER_CAT_END				0x80
+/* hold in idle state */
+#define VOYAGER_CAT_HOLD			0x90
+/* single step an "intest" vector */
+#define VOYAGER_CAT_STEP			0xE0
+/* return cat controller to CLEMSON mode */
+#define VOYAGER_CAT_CLEMSON			0xFF
+
+/* the default cat command header */
+#define VOYAGER_CAT_HEADER			0x7F
+
+/* the range of possible CAT module ids in the system */
+#define VOYAGER_MIN_MODULE			0x10
+#define VOYAGER_MAX_MODULE			0x1f
+
+/* The voyager registers per asic */
+#define VOYAGER_ASIC_ID_REG			0x00
+#define VOYAGER_ASIC_TYPE_REG			0x01
+/* the sub address registers can be made auto incrementing on reads */
+#define VOYAGER_AUTO_INC_REG			0x02
+#	define VOYAGER_AUTO_INC			0x04
+#	define VOYAGER_NO_AUTO_INC		0xfb
+#define VOYAGER_SUBADDRDATA			0x03
+#define VOYAGER_SCANPATH			0x05
+#	define VOYAGER_CONNECT_ASIC		0x01
+#	define VOYAGER_DISCONNECT_ASIC		0xfe
+#define VOYAGER_SUBADDRLO			0x06
+#define VOYAGER_SUBADDRHI			0x07
+#define VOYAGER_SUBMODSELECT			0x08
+#define VOYAGER_SUBMODPRESENT			0x09
+
+#define VOYAGER_SUBADDR_LO			0xff
+#define VOYAGER_SUBADDR_HI			0xffff
+
+/* the maximum size of a scan path -- used to form instructions */
+#define VOYAGER_MAX_SCAN_PATH			0x100
+/* the biggest possible register size (in bytes) */
+#define VOYAGER_MAX_REG_SIZE			4
+
+/* Total number of possible modules (including submodules) */
+#define VOYAGER_MAX_MODULES			16
+/* Largest number of asics per module */
+#define VOYAGER_MAX_ASICS_PER_MODULE		7
+
+/* the CAT asic of each module is always the first one */
+#define VOYAGER_CAT_ID				0
+#define VOYAGER_PSI				0x1a
+
+/* voyager instruction operations and registers */
+#define VOYAGER_READ_CONFIG			0x1
+#define VOYAGER_WRITE_CONFIG			0x2
+#define VOYAGER_BYPASS				0xff
+
+typedef struct voyager_asic 
+{
+	__u8	asic_addr;	/* ASIC address; Level 4 */
+	__u8	asic_type;      /* ASIC type */
+	__u8	asic_id;	/* ASIC id */
+	__u8	jtag_id[4];	/* JTAG id */
+	__u8	asic_location;	/* Location within scan path; start w/ 0 */
+	__u8	bit_location;	/* Location within bit stream; start w/ 0 */
+	__u8	ireg_length;	/* Instruction register length */
+	__u16	subaddr;	/* Amount of sub address space */
+	struct voyager_asic *next;	/* Next asic in linked list */
+} voyager_asic_t;
+
+typedef struct voyager_module {
+	__u8	module_addr;		/* Module address */
+	__u8	scan_path_connected;	/* Scan path connected */
+	__u16   ee_size;		/* Size of the EEPROM */
+	__u16   num_asics;		/* Number of Asics */
+	__u16   inst_bits;		/* Instruction bits in the scan path */
+	__u16   largest_reg;		/* Largest register in the scan path */
+	__u16   smallest_reg;		/* Smallest register in the scan path */
+	voyager_asic_t   *asic;		/* First ASIC in scan path (CAT_I) */
+	struct   voyager_module *submodule;	/* Submodule pointer */ 
+	struct   voyager_module *next;		/* Next module in linked list */
+} voyager_module_t;
+
+typedef struct voyager_eeprom_hdr {
+	 __u8  module_id[4] __attribute__((packed)); 
+	 __u8  version_id __attribute__((packed));
+	 __u8  config_id __attribute__((packed)); 
+	 __u16 boundry_id __attribute__((packed));	/* boundary scan id */
+	 __u16 ee_size __attribute__((packed));		/* size of EEPROM */
+	 __u8  assembly[11] __attribute__((packed));	/* assembly # */
+	 __u8  assembly_rev __attribute__((packed));	/* assembly rev */
+	 __u8  tracer[4] __attribute__((packed));	/* tracer number */
+	 __u16 assembly_cksum __attribute__((packed));	/* asm checksum */
+	 __u16 power_consump __attribute__((packed));	/* pwr requirements */
+	 __u16 num_asics __attribute__((packed));	/* number of asics */
+	 __u16 bist_time __attribute__((packed));	/* min. bist time */
+	 __u16 err_log_offset __attribute__((packed));	/* error log offset */
+	 __u16 scan_path_offset __attribute__((packed));/* scan path offset */
+	 __u16 cct_offset __attribute__((packed));
+	 __u16 log_length __attribute__((packed));	/* length of err log */
+	 __u16 xsum_end __attribute__((packed));	/* offset to end of
+							   checksum */
+	 __u8  reserved[4] __attribute__((packed));
+	 __u8  sflag __attribute__((packed));		/* starting sentinal */
+	 __u8  part_number[13] __attribute__((packed));	/* prom part number */
+	 __u8  version[10] __attribute__((packed));	/* version number */
+	 __u8  signature[8] __attribute__((packed));
+	 __u16 eeprom_chksum __attribute__((packed));
+	 __u32  data_stamp_offset __attribute__((packed));
+	 __u8  eflag  __attribute__((packed));		 /* ending sentinal */
+} voyager_eprom_hdr_t;
+
+
+
+#define VOYAGER_EPROM_SIZE_OFFSET   ((__u16)(&(((voyager_eprom_hdr_t *)0)->ee_size)))
+#define VOYAGER_XSUM_END_OFFSET		0x2a
+
+/* the following three definitions are for internal table layouts
+ * in the module EPROMs.  We really only care about the IDs and
+ * offsets */
+typedef struct voyager_sp_table {
+	__u8 asic_id __attribute__((packed));
+	__u8 bypass_flag __attribute__((packed));
+	__u16 asic_data_offset __attribute__((packed));
+	__u16 config_data_offset __attribute__((packed));
+} voyager_sp_table_t;
+
+typedef struct voyager_jtag_table {
+	__u8 icode[4] __attribute__((packed));
+	__u8 runbist[4] __attribute__((packed));
+	__u8 intest[4] __attribute__((packed));
+	__u8 samp_preld[4] __attribute__((packed));
+	__u8 ireg_len __attribute__((packed));
+} voyager_jtt_t;
+
+typedef struct voyager_asic_data_table {
+	__u8 jtag_id[4] __attribute__((packed));
+	__u16 length_bsr __attribute__((packed));
+	__u16 length_bist_reg __attribute__((packed));
+	__u32 bist_clk __attribute__((packed));
+	__u16 subaddr_bits __attribute__((packed));
+	__u16 seed_bits __attribute__((packed));
+	__u16 sig_bits __attribute__((packed));
+	__u16 jtag_offset __attribute__((packed));
+} voyager_at_t;
+
+/* Voyager Interrupt Controller (VIC) registers */
+
+/* Base to add to Cross Processor Interrupts (CPIs) when triggering
+ * the CPU IRQ line */
+/* register defines for the WCBICs (one per processor) */
+#define VOYAGER_WCBIC0	0x41		/* bus A node P1 processor 0 */
+#define VOYAGER_WCBIC1	0x49		/* bus A node P1 processor 1 */
+#define VOYAGER_WCBIC2	0x51		/* bus A node P2 processor 0 */
+#define VOYAGER_WCBIC3	0x59		/* bus A node P2 processor 1 */
+#define VOYAGER_WCBIC4	0x61		/* bus B node P1 processor 0 */
+#define VOYAGER_WCBIC5	0x69		/* bus B node P1 processor 1 */
+#define VOYAGER_WCBIC6	0x71		/* bus B node P2 processor 0 */
+#define VOYAGER_WCBIC7	0x79		/* bus B node P2 processor 1 */
+
+
+/* top of memory registers */
+#define VOYAGER_WCBIC_TOM_L	0x4
+#define VOYAGER_WCBIC_TOM_H	0x5
+
+/* register defines for Voyager Memory Contol (VMC) 
+ * these are present on L4 machines only */
+#define	VOYAGER_VMC1		0x81
+#define VOYAGER_VMC2		0x91
+#define VOYAGER_VMC3		0xa1
+#define VOYAGER_VMC4		0xb1
+
+/* VMC Ports */
+#define VOYAGER_VMC_MEMORY_SETUP	0x9
+#	define VMC_Interleaving		0x01
+#	define VMC_4Way			0x02
+#	define VMC_EvenCacheLines	0x04
+#	define VMC_HighLine		0x08
+#	define VMC_Start0_Enable	0x20
+#	define VMC_Start1_Enable	0x40
+#	define VMC_Vremap		0x80
+#define VOYAGER_VMC_BANK_DENSITY	0xa
+#	define	VMC_BANK_EMPTY		0
+#	define	VMC_BANK_4MB		1
+#	define	VMC_BANK_16MB		2
+#	define	VMC_BANK_64MB		3
+#	define	VMC_BANK0_MASK		0x03
+#	define	VMC_BANK1_MASK		0x0C
+#	define	VMC_BANK2_MASK		0x30
+#	define	VMC_BANK3_MASK		0xC0
+
+/* Magellan Memory Controller (MMC) defines - present on L5 */
+#define VOYAGER_MMC_ASIC_ID		1
+/* the two memory modules corresponding to memory cards in the system */
+#define VOYAGER_MMC_MEMORY0_MODULE	0x14
+#define VOYAGER_MMC_MEMORY1_MODULE	0x15
+/* the Magellan Memory Address (MMA) defines */
+#define VOYAGER_MMA_ASIC_ID		2
+
+/* Submodule number for the Quad Baseboard */
+#define VOYAGER_QUAD_BASEBOARD		1
+
+/* ASIC defines for the Quad Baseboard */
+#define VOYAGER_QUAD_QDATA0		1
+#define VOYAGER_QUAD_QDATA1		2
+#define VOYAGER_QUAD_QABC		3
+
+/* Useful areas in extended CMOS */
+#define VOYAGER_PROCESSOR_PRESENT_MASK	0x88a
+#define VOYAGER_MEMORY_CLICKMAP		0xa23
+#define VOYAGER_DUMP_LOCATION		0xb1a
+
+/* SUS In Control bit - used to tell SUS that we don't need to be
+ * babysat anymore */
+#define VOYAGER_SUS_IN_CONTROL_PORT	0x3ff
+#	define VOYAGER_IN_CONTROL_FLAG	0x80
+
+/* Voyager PSI defines */
+#define VOYAGER_PSI_STATUS_REG		0x08
+#	define PSI_DC_FAIL		0x01
+#	define PSI_MON			0x02
+#	define PSI_FAULT		0x04
+#	define PSI_ALARM		0x08
+#	define PSI_CURRENT		0x10
+#	define PSI_DVM			0x20
+#	define PSI_PSCFAULT		0x40
+#	define PSI_STAT_CHG		0x80
+
+#define VOYAGER_PSI_SUPPLY_REG		0x8000
+	/* read */
+#	define PSI_FAIL_DC		0x01
+#	define PSI_FAIL_AC		0x02
+#	define PSI_MON_INT		0x04
+#	define PSI_SWITCH_OFF		0x08
+#	define PSI_HX_OFF		0x10
+#	define PSI_SECURITY		0x20
+#	define PSI_CMOS_BATT_LOW	0x40
+#	define PSI_CMOS_BATT_FAIL	0x80
+	/* write */
+#	define PSI_CLR_SWITCH_OFF	0x13
+#	define PSI_CLR_HX_OFF		0x14
+#	define PSI_CLR_CMOS_BATT_FAIL	0x17
+
+#define VOYAGER_PSI_MASK		0x8001
+#	define PSI_MASK_MASK		0x10
+
+#define VOYAGER_PSI_AC_FAIL_REG		0x8004
+#define	AC_FAIL_STAT_CHANGE		0x80
+
+#define VOYAGER_PSI_GENERAL_REG		0x8007
+	/* read */
+#	define PSI_SWITCH_ON		0x01
+#	define PSI_SWITCH_ENABLED	0x02
+#	define PSI_ALARM_ENABLED	0x08
+#	define PSI_SECURE_ENABLED	0x10
+#	define PSI_COLD_RESET		0x20
+#	define PSI_COLD_START		0x80
+	/* write */
+#	define PSI_POWER_DOWN		0x10
+#	define PSI_SWITCH_DISABLE	0x01
+#	define PSI_SWITCH_ENABLE	0x11
+#	define PSI_CLEAR		0x12
+#	define PSI_ALARM_DISABLE	0x03
+#	define PSI_ALARM_ENABLE		0x13
+#	define PSI_CLEAR_COLD_RESET	0x05
+#	define PSI_SET_COLD_RESET	0x15
+#	define PSI_CLEAR_COLD_START	0x07
+#	define PSI_SET_COLD_START	0x17
+
+
+
+struct voyager_bios_info {
+	__u8	len;
+	__u8	major;
+	__u8	minor;
+	__u8	debug;
+	__u8	num_classes;
+	__u8	class_1;
+	__u8	class_2;
+};
+
+/* The following structures and definitions are for the Kernel/SUS
+ * interface these are needed to find out how SUS initialised any Quad
+ * boards in the system */
+
+#define	NUMBER_OF_MC_BUSSES	2
+#define SLOTS_PER_MC_BUS	8
+#define MAX_CPUS                16      /* 16 way CPU system */
+#define MAX_PROCESSOR_BOARDS	4	/* 4 processor slot system */
+#define MAX_CACHE_LEVELS	4	/* # of cache levels supported */
+#define MAX_SHARED_CPUS		4	/* # of CPUs that can share a LARC */
+#define NUMBER_OF_POS_REGS	8
+
+typedef struct {
+	__u8	MC_Slot __attribute__((packed));
+	__u8	POS_Values[NUMBER_OF_POS_REGS] __attribute__((packed));
+} MC_SlotInformation_t;
+
+struct QuadDescription {
+	__u8  Type __attribute__((packed));	/* for type 0 (DYADIC or MONADIC) all fields
+                         * will be zero except for slot */
+	__u8 StructureVersion __attribute__((packed));
+	__u32 CPI_BaseAddress __attribute__((packed));
+	__u32  LARC_BankSize __attribute__((packed));	
+	__u32 LocalMemoryStateBits __attribute__((packed));
+	__u8  Slot __attribute__((packed)); /* Processor slots 1 - 4 */
+}; 
+
+struct ProcBoardInfo { 
+	__u8 Type __attribute__((packed));    
+	__u8 StructureVersion __attribute__((packed));
+	__u8 NumberOfBoards __attribute__((packed));
+	struct QuadDescription QuadData[MAX_PROCESSOR_BOARDS] __attribute__((packed));
+};
+
+struct CacheDescription {
+	__u8 Level __attribute__((packed));
+	__u32 TotalSize __attribute__((packed));
+	__u16 LineSize __attribute__((packed));
+	__u8  Associativity __attribute__((packed));
+	__u8  CacheType __attribute__((packed));
+	__u8  WriteType __attribute__((packed));
+	__u8  Number_CPUs_SharedBy __attribute__((packed));
+	__u8  Shared_CPUs_Hardware_IDs[MAX_SHARED_CPUS] __attribute__((packed));
+
+};
+
+struct CPU_Description {
+	__u8 CPU_HardwareId __attribute__((packed));
+	char *FRU_String __attribute__((packed));
+	__u8 NumberOfCacheLevels __attribute__((packed));
+	struct CacheDescription CacheLevelData[MAX_CACHE_LEVELS] __attribute__((packed));
+};
+
+struct CPU_Info {
+	__u8 Type __attribute__((packed));
+	__u8 StructureVersion __attribute__((packed));
+	__u8 NumberOf_CPUs __attribute__((packed));
+	struct CPU_Description CPU_Data[MAX_CPUS] __attribute__((packed));
+};
+
+
+/*
+ * This structure will be used by SUS and the OS.
+ * The assumption about this structure is that no blank space is
+ * packed in it by our friend the compiler.
+ */
+typedef struct {
+	__u8	Mailbox_SUS;		/* Written to by SUS to give commands/response to the OS */
+	__u8	Mailbox_OS;		/* Written to by the OS to give commands/response to SUS */
+	__u8	SUS_MailboxVersion;	/* Tells the OS which iteration of the interface SUS supports */
+	__u8	OS_MailboxVersion;	/* Tells SUS which iteration of the interface the OS supports */
+	__u32	OS_Flags;		/* Flags set by the OS as info for SUS */
+	__u32	SUS_Flags;		/* Flags set by SUS as info for the OS */
+	__u32	WatchDogPeriod;		/* Watchdog period (in seconds) which the DP uses to see if the OS is dead */
+	__u32	WatchDogCount;		/* Updated by the OS on every tic. */
+	__u32	MemoryFor_SUS_ErrorLog;	/* Flat 32 bit address which tells SUS where to stuff the SUS error log on a dump */
+	MC_SlotInformation_t  MC_SlotInfo[NUMBER_OF_MC_BUSSES*SLOTS_PER_MC_BUS];	/* Storage for MCA POS data */
+	/* All new SECOND_PASS_INTERFACE fields added from this point */
+        struct ProcBoardInfo    *BoardData;
+        struct CPU_Info         *CPU_Data;
+	/* All new fields must be added from this point */
+} Voyager_KernelSUS_Mbox_t;
+
+/* structure for finding the right memory address to send a QIC CPI to */
+struct voyager_qic_cpi {
+	/* Each cache line (32 bytes) can trigger a cpi.  The cpi
+	 * read/write may occur anywhere in the cache line---pick the
+	 * middle to be safe */
+	struct  {
+		__u32 pad1[3];
+		__u32 cpi;
+		__u32 pad2[4];
+	} qic_cpi[8];
+};
+
+struct voyager_status {
+	__u32	power_fail:1;
+	__u32	switch_off:1;
+	__u32	request_from_kernel:1;
+};
+
+struct voyager_psi_regs {
+	__u8 cat_id;
+	__u8 cat_dev;
+	__u8 cat_control;
+	__u8 subaddr;
+	__u8 dummy4;
+	__u8 checkbit;
+	__u8 subaddr_low;
+	__u8 subaddr_high;
+	__u8 intstatus;
+	__u8 stat1;
+	__u8 stat3;
+	__u8 fault;
+	__u8 tms;
+	__u8 gen;
+	__u8 sysconf;
+	__u8 dummy15;
+};
+
+struct voyager_psi_subregs {
+	__u8 supply;
+	__u8 mask;
+	__u8 present;
+	__u8 DCfail;
+	__u8 ACfail;
+	__u8 fail;
+	__u8 UPSfail;
+	__u8 genstatus;
+};
+
+struct voyager_psi {
+	struct voyager_psi_regs regs;
+	struct voyager_psi_subregs subregs;
+};
+
+struct voyager_SUS {
+#define	VOYAGER_DUMP_BUTTON_NMI		0x1
+#define VOYAGER_SUS_VALID		0x2
+#define VOYAGER_SYSINT_COMPLETE		0x3
+	__u8	SUS_mbox;
+#define VOYAGER_NO_COMMAND		0x0
+#define VOYAGER_IGNORE_DUMP		0x1
+#define VOYAGER_DO_DUMP			0x2
+#define VOYAGER_SYSINT_HANDSHAKE	0x3
+#define VOYAGER_DO_MEM_DUMP		0x4
+#define VOYAGER_SYSINT_WAS_RECOVERED	0x5
+	__u8	kernel_mbox;
+#define	VOYAGER_MAILBOX_VERSION		0x10
+	__u8	SUS_version;
+	__u8	kernel_version;
+#define VOYAGER_OS_HAS_SYSINT		0x1
+#define VOYAGER_OS_IN_PROGRESS		0x2
+#define VOYAGER_UPDATING_WDPERIOD	0x4
+	__u32	kernel_flags;
+#define VOYAGER_SUS_BOOTING		0x1
+#define VOYAGER_SUS_IN_PROGRESS		0x2
+	__u32	SUS_flags;
+	__u32	watchdog_period;
+	__u32	watchdog_count;
+	__u32	SUS_errorlog;
+	/* lots of system configuration stuff under here */
+};
+	
+/* Variables exported by voyager_smp */
+extern __u32 voyager_extended_vic_processors;
+extern __u32 voyager_allowed_boot_processors;
+extern __u32 voyager_quad_processors;
+extern struct voyager_qic_cpi *voyager_quad_cpi_addr[NR_CPUS];
+extern struct voyager_SUS *voyager_SUS;
+
+/* variables exported always */
+extern int voyager_level;
+extern int kvoyagerd_running;
+extern struct semaphore kvoyagerd_sem;
+extern struct voyager_status voyager_status;
+
+
+
+/* functions exported by the voyager and voyager_smp modules */
+
+extern int voyager_cat_readb(__u8 module, __u8 asic, int reg);
+extern void voyager_cat_init(void);
+extern void voyager_detect(struct voyager_bios_info *);
+extern void voyager_trap_init(void);
+extern void voyager_setup_irqs(void);
+extern int voyager_memory_detect(int region, __u32 *addr, __u32 *length);
+extern void voyager_smp_intr_init(void);
+extern __u8 voyager_extended_cmos_read(__u16 cmos_address);
+extern void voyager_smp_dump(void);
+extern void voyager_timer_interrupt(struct pt_regs *regs);
+extern void smp_local_timer_interrupt(struct pt_regs * regs);
+extern void voyager_power_off(void);
+extern void smp_voyager_power_off(void *dummy);
+extern void voyager_restart(void);
+extern void voyager_cat_power_off(void);
+extern void voyager_cat_do_common_interrupt(void);
+extern void voyager_handle_nmi(void);
+/* Commands for the following are */
+#define	VOYAGER_PSI_READ	0
+#define VOYAGER_PSI_WRITE	1
+#define VOYAGER_PSI_SUBREAD	2
+#define VOYAGER_PSI_SUBWRITE	3
+extern void voyager_cat_psi(__u8, __u16, __u8 *);