diff --git a/include/asm-sh/mpc1211/dma.h b/include/asm-sh/mpc1211/dma.h
new file mode 100644
index 0000000..0a2fdab
--- /dev/null
+++ b/include/asm-sh/mpc1211/dma.h
@@ -0,0 +1,304 @@
+/* $Id: dma.h,v 1.7 1992/12/14 00:29:34 root Exp root $
+ * linux/include/asm/dma.h: Defines for using and allocating dma channels.
+ * Written by Hennus Bergman, 1992.
+ * High DMA channel support & info by Hannu Savolainen
+ * and John Boyd, Nov. 1992.
+ */
+
+#ifndef _ASM_MPC1211_DMA_H
+#define _ASM_MPC1211_DMA_H
+
+#include <linux/config.h>
+#include <linux/spinlock.h>	/* And spinlocks */
+#include <asm/io.h>		/* need byte IO */
+#include <linux/delay.h>
+
+
+#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
+#define dma_outb	outb_p
+#else
+#define dma_outb	outb
+#endif
+
+#define dma_inb		inb
+
+/*
+ * NOTES about DMA transfers:
+ *
+ *  controller 1: channels 0-3, byte operations, ports 00-1F
+ *  controller 2: channels 4-7, word operations, ports C0-DF
+ *
+ *  - ALL registers are 8 bits only, regardless of transfer size
+ *  - channel 4 is not used - cascades 1 into 2.
+ *  - channels 0-3 are byte - addresses/counts are for physical bytes
+ *  - channels 5-7 are word - addresses/counts are for physical words
+ *  - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
+ *  - transfer count loaded to registers is 1 less than actual count
+ *  - controller 2 offsets are all even (2x offsets for controller 1)
+ *  - page registers for 5-7 don't use data bit 0, represent 128K pages
+ *  - page registers for 0-3 use bit 0, represent 64K pages
+ *
+ * DMA transfers are limited to the lower 16MB of _physical_ memory.  
+ * Note that addresses loaded into registers must be _physical_ addresses,
+ * not logical addresses (which may differ if paging is active).
+ *
+ *  Address mapping for channels 0-3:
+ *
+ *   A23 ... A16 A15 ... A8  A7 ... A0    (Physical addresses)
+ *    |  ...  |   |  ... |   |  ... |
+ *    |  ...  |   |  ... |   |  ... |
+ *    |  ...  |   |  ... |   |  ... |
+ *   P7  ...  P0  A7 ... A0  A7 ... A0   
+ * |    Page    | Addr MSB | Addr LSB |   (DMA registers)
+ *
+ *  Address mapping for channels 5-7:
+ *
+ *   A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0    (Physical addresses)
+ *    |  ...  |   \   \   ... \  \  \  ... \  \
+ *    |  ...  |    \   \   ... \  \  \  ... \  (not used)
+ *    |  ...  |     \   \   ... \  \  \  ... \
+ *   P7  ...  P1 (0) A7 A6  ... A0 A7 A6 ... A0   
+ * |      Page      |  Addr MSB   |  Addr LSB  |   (DMA registers)
+ *
+ * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
+ * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
+ * the hardware level, so odd-byte transfers aren't possible).
+ *
+ * Transfer count (_not # bytes_) is limited to 64K, represented as actual
+ * count - 1 : 64K => 0xFFFF, 1 => 0x0000.  Thus, count is always 1 or more,
+ * and up to 128K bytes may be transferred on channels 5-7 in one operation. 
+ *
+ */
+
+#define MAX_DMA_CHANNELS	8
+
+/* The maximum address that we can perform a DMA transfer to on this platform */
+#define MAX_DMA_ADDRESS      (PAGE_OFFSET+0x10000000)
+
+/* 8237 DMA controllers */
+#define IO_DMA1_BASE	0x00	/* 8 bit slave DMA, channels 0..3 */
+#define IO_DMA2_BASE	0xC0	/* 16 bit master DMA, ch 4(=slave input)..7 */
+
+/* DMA controller registers */
+#define DMA1_CMD_REG		0x08	/* command register (w) */
+#define DMA1_STAT_REG		0x08	/* status register (r) */
+#define DMA1_REQ_REG            0x09    /* request register (w) */
+#define DMA1_MASK_REG		0x0A	/* single-channel mask (w) */
+#define DMA1_MODE_REG		0x0B	/* mode register (w) */
+#define DMA1_CLEAR_FF_REG	0x0C	/* clear pointer flip-flop (w) */
+#define DMA1_TEMP_REG           0x0D    /* Temporary Register (r) */
+#define DMA1_RESET_REG		0x0D	/* Master Clear (w) */
+#define DMA1_CLR_MASK_REG       0x0E    /* Clear Mask */
+#define DMA1_MASK_ALL_REG       0x0F    /* all-channels mask (w) */
+
+#define DMA2_CMD_REG		0xD0	/* command register (w) */
+#define DMA2_STAT_REG		0xD0	/* status register (r) */
+#define DMA2_REQ_REG            0xD2    /* request register (w) */
+#define DMA2_MASK_REG		0xD4	/* single-channel mask (w) */
+#define DMA2_MODE_REG		0xD6	/* mode register (w) */
+#define DMA2_CLEAR_FF_REG	0xD8	/* clear pointer flip-flop (w) */
+#define DMA2_TEMP_REG           0xDA    /* Temporary Register (r) */
+#define DMA2_RESET_REG		0xDA	/* Master Clear (w) */
+#define DMA2_CLR_MASK_REG       0xDC    /* Clear Mask */
+#define DMA2_MASK_ALL_REG       0xDE    /* all-channels mask (w) */
+
+#define DMA_ADDR_0              0x00    /* DMA address registers */
+#define DMA_ADDR_1              0x02
+#define DMA_ADDR_2              0x04
+#define DMA_ADDR_3              0x06
+#define DMA_ADDR_4              0xC0
+#define DMA_ADDR_5              0xC4
+#define DMA_ADDR_6              0xC8
+#define DMA_ADDR_7              0xCC
+
+#define DMA_CNT_0               0x01    /* DMA count registers */
+#define DMA_CNT_1               0x03
+#define DMA_CNT_2               0x05
+#define DMA_CNT_3               0x07
+#define DMA_CNT_4               0xC2
+#define DMA_CNT_5               0xC6
+#define DMA_CNT_6               0xCA
+#define DMA_CNT_7               0xCE
+
+#define DMA_PAGE_0              0x87    /* DMA page registers */
+#define DMA_PAGE_1              0x83
+#define DMA_PAGE_2              0x81
+#define DMA_PAGE_3              0x82
+#define DMA_PAGE_5              0x8B
+#define DMA_PAGE_6              0x89
+#define DMA_PAGE_7              0x8A
+
+#define DMA_MODE_READ	0x44	/* I/O to memory, no autoinit, increment, single mode */
+#define DMA_MODE_WRITE	0x48	/* memory to I/O, no autoinit, increment, single mode */
+#define DMA_MODE_CASCADE 0xC0   /* pass thru DREQ->HRQ, DACK<-HLDA only */
+
+#define DMA_AUTOINIT	0x10
+
+
+extern spinlock_t  dma_spin_lock;
+
+static __inline__ unsigned long claim_dma_lock(void)
+{
+	unsigned long flags;
+	spin_lock_irqsave(&dma_spin_lock, flags);
+	return flags;
+}
+
+static __inline__ void release_dma_lock(unsigned long flags)
+{
+	spin_unlock_irqrestore(&dma_spin_lock, flags);
+}
+
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+	if (dmanr<=3)
+		dma_outb(dmanr,  DMA1_MASK_REG);
+	else
+		dma_outb(dmanr & 3,  DMA2_MASK_REG);
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+	if (dmanr<=3)
+		dma_outb(dmanr | 4,  DMA1_MASK_REG);
+	else
+		dma_outb((dmanr & 3) | 4,  DMA2_MASK_REG);
+}
+
+/* Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while holding the DMA lock ! ---
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+	if (dmanr<=3)
+		dma_outb(0,  DMA1_CLEAR_FF_REG);
+	else
+		dma_outb(0,  DMA2_CLEAR_FF_REG);
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+	if (dmanr<=3)
+		dma_outb(mode | dmanr,  DMA1_MODE_REG);
+	else
+		dma_outb(mode | (dmanr&3),  DMA2_MODE_REG);
+}
+
+/* Set only the page register bits of the transfer address.
+ * This is used for successive transfers when we know the contents of
+ * the lower 16 bits of the DMA current address register, but a 64k boundary
+ * may have been crossed.
+ */
+static __inline__ void set_dma_page(unsigned int dmanr, unsigned int pagenr)
+{
+	switch(dmanr) {
+		case 0:
+			dma_outb( pagenr       & 0xff, DMA_PAGE_0);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_0 + 0x400);
+			break;
+		case 1:
+			dma_outb( pagenr       & 0xff, DMA_PAGE_1);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_1 + 0x400);
+			break;
+		case 2:
+			dma_outb( pagenr       & 0xff, DMA_PAGE_2);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_2 + 0x400);
+			break;
+		case 3:
+			dma_outb( pagenr       & 0xff, DMA_PAGE_3);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_3 + 0x400);
+			break;
+		case 5:
+			dma_outb( pagenr       & 0xfe, DMA_PAGE_5);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_5 + 0x400);
+			break;
+		case 6:
+			dma_outb( pagenr       & 0xfe, DMA_PAGE_6);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_6 + 0x400);
+			break;
+		case 7:
+			dma_outb( pagenr       & 0xfe, DMA_PAGE_7);
+			dma_outb((pagenr >> 8) & 0xff, DMA_PAGE_7 + 0x400);
+			break;
+       	}
+}
+
+
+/* Set transfer address & page bits for specific DMA channel.
+ * Assumes dma flipflop is clear.
+ */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+	set_dma_page(dmanr, a>>16);
+	if (dmanr <= 3)  {
+	    dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
+            dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
+	}  else  {
+	    dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
+	    dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
+	}
+}
+
+
+/* Set transfer size (max 64k for DMA1..3, 128k for DMA5..7) for
+ * a specific DMA channel.
+ * You must ensure the parameters are valid.
+ * NOTE: from a manual: "the number of transfers is one more
+ * than the initial word count"! This is taken into account.
+ * Assumes dma flip-flop is clear.
+ * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+        count--;
+	if (dmanr <= 3)  {
+	    dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
+	    dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
+        } else {
+	    dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
+	    dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
+        }
+}
+
+
+/* Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * If called before the channel has been used, it may return 1.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ *
+ * Assumes DMA flip-flop is clear.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+	unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
+					 : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
+
+	/* using short to get 16-bit wrap around */
+	unsigned short count;
+
+	count = 1 + dma_inb(io_port);
+	count += dma_inb(io_port) << 8;
+	return (dmanr<=3)? count : (count<<1);
+}
+
+
+/* These are in kernel/dma.c: */
+extern int request_dma(unsigned int dmanr, const char * device_id);	/* reserve a DMA channel */
+extern void free_dma(unsigned int dmanr);	/* release it again */
+
+/* From PCI */
+
+#ifdef CONFIG_PCI
+extern int isa_dma_bridge_buggy;
+#else
+#define isa_dma_bridge_buggy 	(0)
+#endif
+
+#endif /* _ASM_MPC1211_DMA_H */
diff --git a/include/asm-sh/mpc1211/io.h b/include/asm-sh/mpc1211/io.h
new file mode 100644
index 0000000..eba8a0b
--- /dev/null
+++ b/include/asm-sh/mpc1211/io.h
@@ -0,0 +1,22 @@
+/*
+ * include/asm-sh/io_mpc1211.h
+ *
+ * Copyright 2001 Saito.K & Jeanne
+ *
+ * IO functions for an Interface MPC-1211
+ */
+
+#ifndef _ASM_SH_IO_MPC1211_H
+#define _ASM_SH_IO_MPC1211_H
+
+#include <linux/time.h>
+
+extern int mpc1211_irq_demux(int irq);
+
+extern void init_mpc1211_IRQ(void);
+extern void heartbeat_mpc1211(void);
+
+extern void mpc1211_rtc_gettimeofday(struct timeval *tv);
+extern int mpc1211_rtc_settimeofday(const struct timeval *tv);
+
+#endif /* _ASM_SH_IO_MPC1211_H */
diff --git a/include/asm-sh/mpc1211/keyboard.h b/include/asm-sh/mpc1211/keyboard.h
new file mode 100644
index 0000000..5f0b908
--- /dev/null
+++ b/include/asm-sh/mpc1211/keyboard.h
@@ -0,0 +1,64 @@
+/*
+ *  MPC1211 specific keybord definitions
+ *  Taken from the old asm-i386/keybord.h for PC/AT-style definitions
+ *  created 3 Nov 1996 by Geert Uytterhoeven.
+ */
+
+#ifdef __KERNEL__
+
+#include <linux/kernel.h>
+#include <linux/ioport.h>
+#include <linux/kd.h>
+#include <linux/pm.h>
+#include <asm/io.h>
+
+#define KEYBOARD_IRQ			1
+#define DISABLE_KBD_DURING_INTERRUPTS	0
+
+extern int pckbd_setkeycode(unsigned int scancode, unsigned int keycode);
+extern int pckbd_getkeycode(unsigned int scancode);
+extern int pckbd_translate(unsigned char scancode, unsigned char *keycode,
+			   char raw_mode);
+extern char pckbd_unexpected_up(unsigned char keycode);
+extern void pckbd_leds(unsigned char leds);
+extern void pckbd_init_hw(void);
+extern int pckbd_pm_resume(struct pm_dev *, pm_request_t, void *);
+extern pm_callback pm_kbd_request_override;
+extern unsigned char pckbd_sysrq_xlate[128];
+
+#define kbd_setkeycode		pckbd_setkeycode
+#define kbd_getkeycode		pckbd_getkeycode
+#define kbd_translate		pckbd_translate
+#define kbd_unexpected_up	pckbd_unexpected_up
+#define kbd_leds		pckbd_leds
+#define kbd_init_hw		pckbd_init_hw
+#define kbd_sysrq_xlate		pckbd_sysrq_xlate
+
+#define SYSRQ_KEY 0x54
+
+/* resource allocation */
+#define kbd_request_region()
+#define kbd_request_irq(handler) request_irq(KEYBOARD_IRQ, handler, 0, \
+                                             "keyboard", NULL)
+
+/* How to access the keyboard macros on this platform.  */
+#define kbd_read_input() inb(KBD_DATA_REG)
+#define kbd_read_status() inb(KBD_STATUS_REG)
+#define kbd_write_output(val) outb(val, KBD_DATA_REG)
+#define kbd_write_command(val) outb(val, KBD_CNTL_REG)
+
+/* Some stoneage hardware needs delays after some operations.  */
+#define kbd_pause() do { } while(0)
+
+/*
+ * Machine specific bits for the PS/2 driver
+ */
+
+#define AUX_IRQ 12
+
+#define aux_request_irq(hand, dev_id)					\
+	request_irq(AUX_IRQ, hand, SA_SHIRQ, "PS2 Mouse", dev_id)
+
+#define aux_free_irq(dev_id) free_irq(AUX_IRQ, dev_id)
+
+#endif /* __KERNEL__ */
diff --git a/include/asm-sh/mpc1211/m1543c.h b/include/asm-sh/mpc1211/m1543c.h
new file mode 100644
index 0000000..c95d132
--- /dev/null
+++ b/include/asm-sh/mpc1211/m1543c.h
@@ -0,0 +1,200 @@
+#ifndef __ASM_SH_M1543C_H
+#define __ASM_SH_M1543C_H
+
+/*
+ * linux/include/asm-sh/m1543c.h
+ * Copyright (C) 2001  Nobuhiro Sakawa
+ * M1543C:PCI-ISA Bus Bridge with Super IO Chip support
+ *
+ * from
+ *
+ * linux/include/asm-sh/smc37c93x.h
+ *
+ * Copyright (C) 2000  Kazumoto Kojima
+ *
+ * SMSC 37C93x Super IO Chip support
+ */
+
+/* Default base I/O address */
+#define FDC_PRIMARY_BASE	0x3f0
+#define IDE1_PRIMARY_BASE	0x1f0
+#define IDE1_SECONDARY_BASE	0x170
+#define PARPORT_PRIMARY_BASE	0x378
+#define COM1_PRIMARY_BASE	0x2f8
+#define COM2_PRIMARY_BASE	0x3f8
+#define COM3_PRIMARY_BASE	0x3e8
+#define RTC_PRIMARY_BASE	0x070
+#define KBC_PRIMARY_BASE	0x060
+#define AUXIO_PRIMARY_BASE	0x000	/* XXX */
+#define I8259_M_CR		0x20
+#define I8259_M_MR		0x21
+#define I8259_S_CR		0xa0
+#define I8259_S_MR		0xa1
+
+/* Logical device number */
+#define LDN_FDC			0
+#define LDN_IDE1		1
+#define LDN_IDE2		2
+#define LDN_PARPORT		3
+#define LDN_COM1		4
+#define LDN_COM2		5
+#define LDN_COM3		11
+#define LDN_RTC			6
+#define LDN_KBC			7
+
+/* Configuration port and key */
+#define CONFIG_PORT		0x3f0
+#define INDEX_PORT		CONFIG_PORT
+#define DATA_PORT		0x3f1
+#define CONFIG_ENTER1		0x51
+#define CONFIG_ENTER2		0x23
+#define CONFIG_EXIT		0xbb
+
+/* Configuration index */
+#define CURRENT_LDN_INDEX	0x07
+#define POWER_CONTROL_INDEX	0x22
+#define ACTIVATE_INDEX		0x30
+#define IO_BASE_HI_INDEX	0x60
+#define IO_BASE_LO_INDEX	0x61
+#define IRQ_SELECT_INDEX	0x70
+#define PS2_IRQ_INDEX		0x72
+#define DMA_SELECT_INDEX	0x74
+
+/* UART stuff. Only for debugging.  */
+/* UART Register */
+
+#define UART_RBR	0x0	/* Receiver Buffer Register (Read Only) */
+#define UART_THR	0x0	/* Transmitter Holding Register (Write Only) */
+#define UART_IER	0x2	/* Interrupt Enable Register */
+#define UART_IIR	0x4	/* Interrupt Ident Register (Read Only) */
+#define UART_FCR	0x4	/* FIFO Control Register (Write Only) */
+#define UART_LCR	0x6	/* Line Control Register */
+#define UART_MCR	0x8	/* MODEM Control Register */
+#define UART_LSR	0xa	/* Line Status Register */
+#define UART_MSR	0xc	/* MODEM Status Register */
+#define UART_SCR	0xe	/* Scratch Register */
+#define UART_DLL	0x0	/* Divisor Latch (LS) */
+#define UART_DLM	0x2	/* Divisor Latch (MS) */
+
+#ifndef __ASSEMBLY__
+typedef struct uart_reg {
+	volatile __u16 rbr;
+	volatile __u16 ier;
+	volatile __u16 iir;
+	volatile __u16 lcr;
+	volatile __u16 mcr;
+	volatile __u16 lsr;
+	volatile __u16 msr;
+	volatile __u16 scr;
+} uart_reg;
+#endif /* ! __ASSEMBLY__ */
+
+/* Alias for Write Only Register */
+
+#define thr	rbr
+#define tcr	iir
+
+/* Alias for Divisor Latch Register */
+
+#define dll	rbr
+#define dlm	ier
+#define fcr	iir
+
+/* Interrupt Enable Register */
+
+#define IER_ERDAI	0x0100	/* Enable Received Data Available Interrupt */
+#define IER_ETHREI	0x0200	/* Enable Transmitter Holding Register Empty Interrupt */
+#define IER_ELSI	0x0400	/* Enable Receiver Line Status Interrupt */
+#define IER_EMSI	0x0800	/* Enable MODEM Status Interrupt */
+
+/* Interrupt Ident Register */
+
+#define IIR_IP		0x0100	/* "0" if Interrupt Pending */
+#define IIR_IIB0	0x0200	/* Interrupt ID Bit 0 */
+#define IIR_IIB1	0x0400	/* Interrupt ID Bit 1 */
+#define IIR_IIB2	0x0800	/* Interrupt ID Bit 2 */
+#define IIR_FIFO	0xc000	/* FIFOs enabled */
+
+/* FIFO Control Register */
+
+#define FCR_FEN		0x0100	/* FIFO enable */
+#define FCR_RFRES	0x0200	/* Receiver FIFO reset */
+#define FCR_TFRES	0x0400	/* Transmitter FIFO reset */
+#define FCR_DMA		0x0800	/* DMA mode select */
+#define FCR_RTL		0x4000	/* Receiver triger (LSB) */
+#define FCR_RTM		0x8000	/* Receiver triger (MSB) */
+
+/* Line Control Register */
+
+#define LCR_WLS0	0x0100	/* Word Length Select Bit 0 */
+#define LCR_WLS1	0x0200	/* Word Length Select Bit 1 */
+#define LCR_STB		0x0400	/* Number of Stop Bits */
+#define LCR_PEN		0x0800	/* Parity Enable */
+#define LCR_EPS		0x1000	/* Even Parity Select */
+#define LCR_SP		0x2000	/* Stick Parity */
+#define LCR_SB		0x4000	/* Set Break */
+#define LCR_DLAB	0x8000	/* Divisor Latch Access Bit */
+
+/* MODEM Control Register */
+
+#define MCR_DTR		0x0100	/* Data Terminal Ready */
+#define MCR_RTS		0x0200	/* Request to Send */
+#define MCR_OUT1	0x0400	/* Out 1 */
+#define MCR_IRQEN	0x0800	/* IRQ Enable */
+#define MCR_LOOP	0x1000	/* Loop */
+
+/* Line Status Register */
+
+#define LSR_DR		0x0100	/* Data Ready */
+#define LSR_OE		0x0200	/* Overrun Error */
+#define LSR_PE		0x0400	/* Parity Error */
+#define LSR_FE		0x0800	/* Framing Error */
+#define LSR_BI		0x1000	/* Break Interrupt */
+#define LSR_THRE	0x2000	/* Transmitter Holding Register Empty */
+#define LSR_TEMT	0x4000	/* Transmitter Empty */
+#define LSR_FIFOE	0x8000	/* Receiver FIFO error */
+
+/* MODEM Status Register */
+
+#define MSR_DCTS	0x0100	/* Delta Clear to Send */
+#define MSR_DDSR	0x0200	/* Delta Data Set Ready */
+#define MSR_TERI	0x0400	/* Trailing Edge Ring Indicator */
+#define MSR_DDCD	0x0800	/* Delta Data Carrier Detect */
+#define MSR_CTS		0x1000	/* Clear to Send */
+#define MSR_DSR		0x2000	/* Data Set Ready */
+#define MSR_RI		0x4000	/* Ring Indicator */
+#define MSR_DCD		0x8000	/* Data Carrier Detect */
+
+/* Baud Rate Divisor */
+
+#define UART_CLK	(1843200)	/* 1.8432 MHz */
+#define UART_BAUD(x)	(UART_CLK / (16 * (x)))
+
+/* RTC register definition */
+#define RTC_SECONDS             0
+#define RTC_SECONDS_ALARM       1
+#define RTC_MINUTES             2
+#define RTC_MINUTES_ALARM       3
+#define RTC_HOURS               4
+#define RTC_HOURS_ALARM         5
+#define RTC_DAY_OF_WEEK         6
+#define RTC_DAY_OF_MONTH        7
+#define RTC_MONTH               8
+#define RTC_YEAR                9
+#define RTC_FREQ_SELECT		10
+# define RTC_UIP 0x80
+# define RTC_DIV_CTL 0x70
+/* This RTC can work under 32.768KHz clock only.  */
+# define RTC_OSC_ENABLE 0x20
+# define RTC_OSC_DISABLE 0x00
+#define RTC_CONTROL     	11
+# define RTC_SET 0x80
+# define RTC_PIE 0x40
+# define RTC_AIE 0x20
+# define RTC_UIE 0x10
+# define RTC_SQWE 0x08
+# define RTC_DM_BINARY 0x04
+# define RTC_24H 0x02
+# define RTC_DST_EN 0x01
+
+#endif  /* __ASM_SH_M1543C_H */
diff --git a/include/asm-sh/mpc1211/mc146818rtc.h b/include/asm-sh/mpc1211/mc146818rtc.h
new file mode 100644
index 0000000..0ec78f6
--- /dev/null
+++ b/include/asm-sh/mpc1211/mc146818rtc.h
@@ -0,0 +1,6 @@
+/*
+ * MPC1211 uses PC/AT style RTC definitions.
+ */
+#include <asm-i386/mc146818rtc.h>
+
+
diff --git a/include/asm-sh/mpc1211/mpc1211.h b/include/asm-sh/mpc1211/mpc1211.h
new file mode 100644
index 0000000..fa456c3
--- /dev/null
+++ b/include/asm-sh/mpc1211/mpc1211.h
@@ -0,0 +1,18 @@
+#ifndef __ASM_SH_MPC1211_H
+#define __ASM_SH_MPC1211_H
+
+/*
+ * linux/include/asm-sh/mpc1211.h
+ *
+ * Copyright (C) 2001  Saito.K & Jeanne
+ *
+ * Interface MPC-1211 support
+ */
+
+#define PA_PCI_IO       (0xa4000000)    /* PCI I/O space */
+#define PA_PCI_MEM      (0xb0000000)    /* PCI MEM space */
+
+#define PCIPAR          (0xa4000cf8)    /* PCI Config address */
+#define PCIPDR          (0xa4000cfc)    /* PCI Config data    */
+
+#endif  /* __ASM_SH_MPC1211_H */
diff --git a/include/asm-sh/mpc1211/pci.h b/include/asm-sh/mpc1211/pci.h
new file mode 100644
index 0000000..5d3712c
--- /dev/null
+++ b/include/asm-sh/mpc1211/pci.h
@@ -0,0 +1,40 @@
+/*
+ *	Low-Level PCI Support for MPC-1211
+ *
+ *      (c) 2002 Saito.K & Jeanne
+ *
+ */
+
+#ifndef _PCI_MPC1211_H_
+#define _PCI_MPC1211_H_
+
+#include <linux/pci.h>
+
+/* set debug level 4=verbose...1=terse */
+//#define DEBUG_PCI 3
+#undef DEBUG_PCI
+
+#ifdef DEBUG_PCI
+#define PCIDBG(n, x...) { if(DEBUG_PCI>=n) printk(x); }
+#else
+#define PCIDBG(n, x...)
+#endif
+
+/* startup values */
+#define PCI_PROBE_BIOS    1
+#define PCI_PROBE_CONF1   2
+#define PCI_PROBE_CONF2   4
+#define PCI_NO_SORT       0x100
+#define PCI_BIOS_SORT     0x200
+#define PCI_NO_CHECKS     0x400
+#define PCI_ASSIGN_ROMS   0x1000
+#define PCI_BIOS_IRQ_SCAN 0x2000
+
+/* MPC-1211 Specific Values */
+#define PCIPAR            (0xa4000cf8)    /* PCI Config address */
+#define PCIPDR            (0xa4000cfc)    /* PCI Config data    */
+
+#define PA_PCI_IO         (0xa4000000)    /* PCI I/O space */
+#define PA_PCI_MEM        (0xb0000000)    /* PCI MEM space */
+
+#endif /* _PCI_MPC1211_H_ */