[SCSI] mptfusion - bus_type, change SCSI to SPI
This changes to SPI for the bus_type enumeration.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
diff --git a/drivers/message/fusion/mptscsih.c b/drivers/message/fusion/mptscsih.c
index b7b9846..2d01424 100644
--- a/drivers/message/fusion/mptscsih.c
+++ b/drivers/message/fusion/mptscsih.c
@@ -677,7 +677,7 @@
sc->result = DID_RESET << 16;
/* GEM Workaround. */
- if (ioc->bus_type == SCSI)
+ if (ioc->bus_type == SPI)
mptscsih_no_negotiate(hd, sc->device->id);
break;
@@ -1403,7 +1403,7 @@
SCpnt->host_scribble = NULL;
#ifdef MPTSCSIH_ENABLE_DOMAIN_VALIDATION
- if (hd->ioc->bus_type == SCSI) {
+ if (hd->ioc->bus_type == SPI) {
int dvStatus = hd->ioc->spi_data.dvStatus[pTarget->target_id];
int issueCmd = 1;
@@ -2183,7 +2183,7 @@
vdev->bus_id = device->channel;
vdev->raidVolume = 0;
hd->Targets[device->id] = vdev;
- if (hd->ioc->bus_type == SCSI) {
+ if (hd->ioc->bus_type == SPI) {
if (hd->ioc->raid_data.isRaid & (1 << device->id)) {
vdev->raidVolume = 1;
ddvtprintk((KERN_INFO
@@ -2225,7 +2225,7 @@
kfree(hd->Targets[target]);
hd->Targets[target] = NULL;
- if (hd->ioc->bus_type == SCSI) {
+ if (hd->ioc->bus_type == SPI) {
if (mptscsih_is_phys_disk(hd->ioc, target)) {
hd->ioc->spi_data.forceDv |= MPT_SCSICFG_RELOAD_IOC_PG3;
} else {
@@ -2261,7 +2261,7 @@
if (!(pTarget = hd->Targets[sdev->id]))
return 0;
- if (hd->ioc->bus_type == SCSI) {
+ if (hd->ioc->bus_type == SPI) {
if (pTarget->tflags & MPT_TARGET_FLAGS_VALID_INQUIRY) {
if (!(pTarget->tflags & MPT_TARGET_FLAGS_Q_YES))
max_depth = 1;
@@ -2503,9 +2503,9 @@
/* 2. Chain Buffer initialization
*/
- /* 4. Renegotiate to all devices, if SCSI
+ /* 4. Renegotiate to all devices, if SPI
*/
- if (ioc->bus_type == SCSI) {
+ if (ioc->bus_type == SPI) {
dnegoprintk(("writeSDP1: ALL_IDS USE_NVRAM\n"));
mptscsih_writeSDP1(hd, 0, 0, MPT_SCSICFG_ALL_IDS | MPT_SCSICFG_USE_NVRAM);
}
@@ -2534,7 +2534,7 @@
/* 7. Set flag to force DV and re-read IOC Page 3
*/
- if (ioc->bus_type == SCSI) {
+ if (ioc->bus_type == SPI) {
ioc->spi_data.forceDv = MPT_SCSICFG_NEED_DV | MPT_SCSICFG_RELOAD_IOC_PG3;
ddvtprintk(("Set reload IOC Pg3 Flag\n"));
}
@@ -2576,7 +2576,7 @@
break;
case MPI_EVENT_IOC_BUS_RESET: /* 04 */
case MPI_EVENT_EXT_BUS_RESET: /* 05 */
- if (hd && (ioc->bus_type == SCSI) && (hd->soft_resets < -1))
+ if (hd && (ioc->bus_type == SPI) && (hd->soft_resets < -1))
hd->soft_resets++;
break;
case MPI_EVENT_LOGOUT: /* 09 */
@@ -2601,7 +2601,7 @@
(pMpiEventDataRaid_t) pEvReply->Data;
#ifdef MPTSCSIH_ENABLE_DOMAIN_VALIDATION
/* Domain Validation Needed */
- if (ioc->bus_type == SCSI &&
+ if (ioc->bus_type == SPI &&
pRaidEventData->ReasonCode ==
MPI_EVENT_RAID_RC_DOMAIN_VAL_NEEDED)
mptscsih_set_dvflags_raid(hd, pRaidEventData->PhysDiskNum);
@@ -2682,7 +2682,7 @@
indexed_lun = (lun % 32);
vdev->luns[lun_index] |= (1 << indexed_lun);
- if (hd->ioc->bus_type == SCSI) {
+ if (hd->ioc->bus_type == SPI) {
if ((data[0] == TYPE_PROCESSOR) && (hd->ioc->spi_data.Saf_Te)) {
/* Treat all Processors as SAF-TE if
* command line option is set */
@@ -3956,10 +3956,10 @@
if (id == hostId)
id++;
- /* Write SDP1 for all SCSI devices
+ /* Write SDP1 for all SPI devices
* Alloc memory and set up config buffer
*/
- if (ioc->bus_type == SCSI) {
+ if (ioc->bus_type == SPI) {
if (ioc->spi_data.sdp1length > 0) {
pcfg1Data = (SCSIDevicePage1_t *)pci_alloc_consistent(ioc->pcidev,
ioc->spi_data.sdp1length * 4, &cfg1_dma_addr);
@@ -4101,8 +4101,8 @@
msleep(250);
- /* DV only to SCSI adapters */
- if (ioc->bus_type != SCSI)
+ /* DV only to SPI adapters */
+ if (ioc->bus_type != SPI)
continue;
/* Make sure everything looks ok */