ARM: ux500: switch MSP to using pinctrl for pins
The MSP platform data callbacks use the old custom callbacks to
set the state of the pins, switch over to using pinctrl.
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index dccd29d..32fd992 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -32,12 +32,14 @@
BIAS(pd, PIN_PULL_DOWN);
BIAS(slpm_gpio_nopull, PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
BIAS(in_nopull, PIN_INPUT_NOPULL);
+BIAS(in_nopull_sleep_nowkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_DISABLE);
BIAS(in_pu, PIN_INPUT_PULLUP);
BIAS(in_pd, PIN_INPUT_PULLDOWN);
BIAS(in_pd_slpm_in_pu, PIN_INPUT_PULLDOWN|PIN_SLPM_INPUT_PULLUP);
BIAS(in_pu_slpm_out_lo, PIN_INPUT_PULLUP|PIN_SLPM_OUTPUT_LOW);
BIAS(out_hi, PIN_OUTPUT_HIGH);
BIAS(out_lo, PIN_OUTPUT_LOW);
+BIAS(out_lo_sleep_nowkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE);
/* These also force them into GPIO mode */
BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
@@ -47,7 +49,9 @@
BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
/* Sleep modes */
BIAS(sleep_in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+BIAS(sleep_in_nopull_wkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE);
BIAS(sleep_out_hi_wkup_pdis, PIN_SLPM_OUTPUT_HIGH|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+BIAS(sleep_out_lo_wkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE);
BIAS(sleep_out_wkup_pdis, PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
/* We use these to define hog settings that are always done on boot */
@@ -129,11 +133,23 @@
DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
- /* Sleep state for UART0 */
+ /* UART0 sleep state */
DB8500_PIN_SLEEP("GPIO0_AJ5", sleep_in_wkup_pdis, "uart0"),
DB8500_PIN_SLEEP("GPIO1_AJ3", sleep_out_hi_wkup_pdis, "uart0"),
DB8500_PIN_SLEEP("GPIO2_AH4", sleep_in_wkup_pdis, "uart0"),
DB8500_PIN_SLEEP("GPIO3_AH3", sleep_out_wkup_pdis, "uart0"),
+ /* MSP1 for ALSA codec */
+ DB8500_MUX("msp1txrx_a_1", "msp1", "ux500-msp-i2s.1"),
+ DB8500_MUX("msp1_a_1", "msp1", "ux500-msp-i2s.1"),
+ DB8500_PIN("GPIO33_AF2", out_lo_sleep_nowkup, "ux500-msp-i2s.1"),
+ DB8500_PIN("GPIO34_AE1", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+ DB8500_PIN("GPIO35_AE2", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+ DB8500_PIN("GPIO36_AG2", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+ /* MSP1 sleep state */
+ DB8500_PIN_SLEEP("GPIO33_AF2", sleep_out_lo_wkup, "ux500-msp-i2s.1"),
+ DB8500_PIN_SLEEP("GPIO34_AE1", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+ DB8500_PIN_SLEEP("GPIO35_AE2", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+ DB8500_PIN_SLEEP("GPIO36_AG2", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),