| /* | 
 |  * drivers/mtd/nand/gpio.c | 
 |  * | 
 |  * Updated, and converted to generic GPIO based driver by Russell King. | 
 |  * | 
 |  * Written by Ben Dooks <ben@simtec.co.uk> | 
 |  *   Based on 2.4 version by Mark Whittaker | 
 |  * | 
 |  * © 2004 Simtec Electronics | 
 |  * | 
 |  * Device driver for NAND connected via GPIO | 
 |  * | 
 |  * This program is free software; you can redistribute it and/or modify | 
 |  * it under the terms of the GNU General Public License version 2 as | 
 |  * published by the Free Software Foundation. | 
 |  * | 
 |  */ | 
 |  | 
 | #include <linux/kernel.h> | 
 | #include <linux/init.h> | 
 | #include <linux/slab.h> | 
 | #include <linux/module.h> | 
 | #include <linux/platform_device.h> | 
 | #include <linux/gpio.h> | 
 | #include <linux/io.h> | 
 | #include <linux/mtd/mtd.h> | 
 | #include <linux/mtd/nand.h> | 
 | #include <linux/mtd/partitions.h> | 
 | #include <linux/mtd/nand-gpio.h> | 
 | #include <linux/of.h> | 
 | #include <linux/of_address.h> | 
 | #include <linux/of_gpio.h> | 
 |  | 
 | struct gpiomtd { | 
 | 	void __iomem		*io_sync; | 
 | 	struct mtd_info		mtd_info; | 
 | 	struct nand_chip	nand_chip; | 
 | 	struct gpio_nand_platdata plat; | 
 | }; | 
 |  | 
 | #define gpio_nand_getpriv(x) container_of(x, struct gpiomtd, mtd_info) | 
 |  | 
 |  | 
 | #ifdef CONFIG_ARM | 
 | /* gpio_nand_dosync() | 
 |  * | 
 |  * Make sure the GPIO state changes occur in-order with writes to NAND | 
 |  * memory region. | 
 |  * Needed on PXA due to bus-reordering within the SoC itself (see section on | 
 |  * I/O ordering in PXA manual (section 2.3, p35) | 
 |  */ | 
 | static void gpio_nand_dosync(struct gpiomtd *gpiomtd) | 
 | { | 
 | 	unsigned long tmp; | 
 |  | 
 | 	if (gpiomtd->io_sync) { | 
 | 		/* | 
 | 		 * Linux memory barriers don't cater for what's required here. | 
 | 		 * What's required is what's here - a read from a separate | 
 | 		 * region with a dependency on that read. | 
 | 		 */ | 
 | 		tmp = readl(gpiomtd->io_sync); | 
 | 		asm volatile("mov %1, %0\n" : "=r" (tmp) : "r" (tmp)); | 
 | 	} | 
 | } | 
 | #else | 
 | static inline void gpio_nand_dosync(struct gpiomtd *gpiomtd) {} | 
 | #endif | 
 |  | 
 | static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) | 
 | { | 
 | 	struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd); | 
 |  | 
 | 	gpio_nand_dosync(gpiomtd); | 
 |  | 
 | 	if (ctrl & NAND_CTRL_CHANGE) { | 
 | 		gpio_set_value(gpiomtd->plat.gpio_nce, !(ctrl & NAND_NCE)); | 
 | 		gpio_set_value(gpiomtd->plat.gpio_cle, !!(ctrl & NAND_CLE)); | 
 | 		gpio_set_value(gpiomtd->plat.gpio_ale, !!(ctrl & NAND_ALE)); | 
 | 		gpio_nand_dosync(gpiomtd); | 
 | 	} | 
 | 	if (cmd == NAND_CMD_NONE) | 
 | 		return; | 
 |  | 
 | 	writeb(cmd, gpiomtd->nand_chip.IO_ADDR_W); | 
 | 	gpio_nand_dosync(gpiomtd); | 
 | } | 
 |  | 
 | static void gpio_nand_writebuf(struct mtd_info *mtd, const u_char *buf, int len) | 
 | { | 
 | 	struct nand_chip *this = mtd->priv; | 
 |  | 
 | 	writesb(this->IO_ADDR_W, buf, len); | 
 | } | 
 |  | 
 | static void gpio_nand_readbuf(struct mtd_info *mtd, u_char *buf, int len) | 
 | { | 
 | 	struct nand_chip *this = mtd->priv; | 
 |  | 
 | 	readsb(this->IO_ADDR_R, buf, len); | 
 | } | 
 |  | 
 | static int gpio_nand_verifybuf(struct mtd_info *mtd, const u_char *buf, int len) | 
 | { | 
 | 	struct nand_chip *this = mtd->priv; | 
 | 	unsigned char read, *p = (unsigned char *) buf; | 
 | 	int i, err = 0; | 
 |  | 
 | 	for (i = 0; i < len; i++) { | 
 | 		read = readb(this->IO_ADDR_R); | 
 | 		if (read != p[i]) { | 
 | 			pr_debug("%s: err at %d (read %04x vs %04x)\n", | 
 | 			       __func__, i, read, p[i]); | 
 | 			err = -EFAULT; | 
 | 		} | 
 | 	} | 
 | 	return err; | 
 | } | 
 |  | 
 | static void gpio_nand_writebuf16(struct mtd_info *mtd, const u_char *buf, | 
 | 				 int len) | 
 | { | 
 | 	struct nand_chip *this = mtd->priv; | 
 |  | 
 | 	if (IS_ALIGNED((unsigned long)buf, 2)) { | 
 | 		writesw(this->IO_ADDR_W, buf, len>>1); | 
 | 	} else { | 
 | 		int i; | 
 | 		unsigned short *ptr = (unsigned short *)buf; | 
 |  | 
 | 		for (i = 0; i < len; i += 2, ptr++) | 
 | 			writew(*ptr, this->IO_ADDR_W); | 
 | 	} | 
 | } | 
 |  | 
 | static void gpio_nand_readbuf16(struct mtd_info *mtd, u_char *buf, int len) | 
 | { | 
 | 	struct nand_chip *this = mtd->priv; | 
 |  | 
 | 	if (IS_ALIGNED((unsigned long)buf, 2)) { | 
 | 		readsw(this->IO_ADDR_R, buf, len>>1); | 
 | 	} else { | 
 | 		int i; | 
 | 		unsigned short *ptr = (unsigned short *)buf; | 
 |  | 
 | 		for (i = 0; i < len; i += 2, ptr++) | 
 | 			*ptr = readw(this->IO_ADDR_R); | 
 | 	} | 
 | } | 
 |  | 
 | static int gpio_nand_verifybuf16(struct mtd_info *mtd, const u_char *buf, | 
 | 				 int len) | 
 | { | 
 | 	struct nand_chip *this = mtd->priv; | 
 | 	unsigned short read, *p = (unsigned short *) buf; | 
 | 	int i, err = 0; | 
 | 	len >>= 1; | 
 |  | 
 | 	for (i = 0; i < len; i++) { | 
 | 		read = readw(this->IO_ADDR_R); | 
 | 		if (read != p[i]) { | 
 | 			pr_debug("%s: err at %d (read %04x vs %04x)\n", | 
 | 			       __func__, i, read, p[i]); | 
 | 			err = -EFAULT; | 
 | 		} | 
 | 	} | 
 | 	return err; | 
 | } | 
 |  | 
 |  | 
 | static int gpio_nand_devready(struct mtd_info *mtd) | 
 | { | 
 | 	struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd); | 
 | 	return gpio_get_value(gpiomtd->plat.gpio_rdy); | 
 | } | 
 |  | 
 | #ifdef CONFIG_OF | 
 | static const struct of_device_id gpio_nand_id_table[] = { | 
 | 	{ .compatible = "gpio-control-nand" }, | 
 | 	{} | 
 | }; | 
 | MODULE_DEVICE_TABLE(of, gpio_nand_id_table); | 
 |  | 
 | static int gpio_nand_get_config_of(const struct device *dev, | 
 | 				   struct gpio_nand_platdata *plat) | 
 | { | 
 | 	u32 val; | 
 |  | 
 | 	if (!of_property_read_u32(dev->of_node, "bank-width", &val)) { | 
 | 		if (val == 2) { | 
 | 			plat->options |= NAND_BUSWIDTH_16; | 
 | 		} else if (val != 1) { | 
 | 			dev_err(dev, "invalid bank-width %u\n", val); | 
 | 			return -EINVAL; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	plat->gpio_rdy = of_get_gpio(dev->of_node, 0); | 
 | 	plat->gpio_nce = of_get_gpio(dev->of_node, 1); | 
 | 	plat->gpio_ale = of_get_gpio(dev->of_node, 2); | 
 | 	plat->gpio_cle = of_get_gpio(dev->of_node, 3); | 
 | 	plat->gpio_nwp = of_get_gpio(dev->of_node, 4); | 
 |  | 
 | 	if (!of_property_read_u32(dev->of_node, "chip-delay", &val)) | 
 | 		plat->chip_delay = val; | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static struct resource *gpio_nand_get_io_sync_of(struct platform_device *pdev) | 
 | { | 
 | 	struct resource *r = devm_kzalloc(&pdev->dev, sizeof(*r), GFP_KERNEL); | 
 | 	u64 addr; | 
 |  | 
 | 	if (!r || of_property_read_u64(pdev->dev.of_node, | 
 | 				       "gpio-control-nand,io-sync-reg", &addr)) | 
 | 		return NULL; | 
 |  | 
 | 	r->start = addr; | 
 | 	r->end = r->start + 0x3; | 
 | 	r->flags = IORESOURCE_MEM; | 
 |  | 
 | 	return r; | 
 | } | 
 | #else /* CONFIG_OF */ | 
 | #define gpio_nand_id_table NULL | 
 | static inline int gpio_nand_get_config_of(const struct device *dev, | 
 | 					  struct gpio_nand_platdata *plat) | 
 | { | 
 | 	return -ENOSYS; | 
 | } | 
 |  | 
 | static inline struct resource * | 
 | gpio_nand_get_io_sync_of(struct platform_device *pdev) | 
 | { | 
 | 	return NULL; | 
 | } | 
 | #endif /* CONFIG_OF */ | 
 |  | 
 | static inline int gpio_nand_get_config(const struct device *dev, | 
 | 				       struct gpio_nand_platdata *plat) | 
 | { | 
 | 	int ret = gpio_nand_get_config_of(dev, plat); | 
 |  | 
 | 	if (!ret) | 
 | 		return ret; | 
 |  | 
 | 	if (dev->platform_data) { | 
 | 		memcpy(plat, dev->platform_data, sizeof(*plat)); | 
 | 		return 0; | 
 | 	} | 
 |  | 
 | 	return -EINVAL; | 
 | } | 
 |  | 
 | static inline struct resource * | 
 | gpio_nand_get_io_sync(struct platform_device *pdev) | 
 | { | 
 | 	struct resource *r = gpio_nand_get_io_sync_of(pdev); | 
 |  | 
 | 	if (r) | 
 | 		return r; | 
 |  | 
 | 	return platform_get_resource(pdev, IORESOURCE_MEM, 1); | 
 | } | 
 |  | 
 | static int __devexit gpio_nand_remove(struct platform_device *dev) | 
 | { | 
 | 	struct gpiomtd *gpiomtd = platform_get_drvdata(dev); | 
 | 	struct resource *res; | 
 |  | 
 | 	nand_release(&gpiomtd->mtd_info); | 
 |  | 
 | 	res = gpio_nand_get_io_sync(dev); | 
 | 	iounmap(gpiomtd->io_sync); | 
 | 	if (res) | 
 | 		release_mem_region(res->start, resource_size(res)); | 
 |  | 
 | 	res = platform_get_resource(dev, IORESOURCE_MEM, 0); | 
 | 	iounmap(gpiomtd->nand_chip.IO_ADDR_R); | 
 | 	release_mem_region(res->start, resource_size(res)); | 
 |  | 
 | 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) | 
 | 		gpio_set_value(gpiomtd->plat.gpio_nwp, 0); | 
 | 	gpio_set_value(gpiomtd->plat.gpio_nce, 1); | 
 |  | 
 | 	gpio_free(gpiomtd->plat.gpio_cle); | 
 | 	gpio_free(gpiomtd->plat.gpio_ale); | 
 | 	gpio_free(gpiomtd->plat.gpio_nce); | 
 | 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) | 
 | 		gpio_free(gpiomtd->plat.gpio_nwp); | 
 | 	gpio_free(gpiomtd->plat.gpio_rdy); | 
 |  | 
 | 	kfree(gpiomtd); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | static void __iomem *request_and_remap(struct resource *res, size_t size, | 
 | 					const char *name, int *err) | 
 | { | 
 | 	void __iomem *ptr; | 
 |  | 
 | 	if (!request_mem_region(res->start, resource_size(res), name)) { | 
 | 		*err = -EBUSY; | 
 | 		return NULL; | 
 | 	} | 
 |  | 
 | 	ptr = ioremap(res->start, size); | 
 | 	if (!ptr) { | 
 | 		release_mem_region(res->start, resource_size(res)); | 
 | 		*err = -ENOMEM; | 
 | 	} | 
 | 	return ptr; | 
 | } | 
 |  | 
 | static int __devinit gpio_nand_probe(struct platform_device *dev) | 
 | { | 
 | 	struct gpiomtd *gpiomtd; | 
 | 	struct nand_chip *this; | 
 | 	struct resource *res0, *res1; | 
 | 	struct mtd_part_parser_data ppdata = {}; | 
 | 	int ret = 0; | 
 |  | 
 | 	if (!dev->dev.of_node && !dev->dev.platform_data) | 
 | 		return -EINVAL; | 
 |  | 
 | 	res0 = platform_get_resource(dev, IORESOURCE_MEM, 0); | 
 | 	if (!res0) | 
 | 		return -EINVAL; | 
 |  | 
 | 	gpiomtd = kzalloc(sizeof(*gpiomtd), GFP_KERNEL); | 
 | 	if (gpiomtd == NULL) { | 
 | 		dev_err(&dev->dev, "failed to create NAND MTD\n"); | 
 | 		return -ENOMEM; | 
 | 	} | 
 |  | 
 | 	this = &gpiomtd->nand_chip; | 
 | 	this->IO_ADDR_R = request_and_remap(res0, 2, "NAND", &ret); | 
 | 	if (!this->IO_ADDR_R) { | 
 | 		dev_err(&dev->dev, "unable to map NAND\n"); | 
 | 		goto err_map; | 
 | 	} | 
 |  | 
 | 	res1 = gpio_nand_get_io_sync(dev); | 
 | 	if (res1) { | 
 | 		gpiomtd->io_sync = request_and_remap(res1, 4, "NAND sync", &ret); | 
 | 		if (!gpiomtd->io_sync) { | 
 | 			dev_err(&dev->dev, "unable to map sync NAND\n"); | 
 | 			goto err_sync; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	ret = gpio_nand_get_config(&dev->dev, &gpiomtd->plat); | 
 | 	if (ret) | 
 | 		goto err_nce; | 
 |  | 
 | 	ret = gpio_request(gpiomtd->plat.gpio_nce, "NAND NCE"); | 
 | 	if (ret) | 
 | 		goto err_nce; | 
 | 	gpio_direction_output(gpiomtd->plat.gpio_nce, 1); | 
 | 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) { | 
 | 		ret = gpio_request(gpiomtd->plat.gpio_nwp, "NAND NWP"); | 
 | 		if (ret) | 
 | 			goto err_nwp; | 
 | 		gpio_direction_output(gpiomtd->plat.gpio_nwp, 1); | 
 | 	} | 
 | 	ret = gpio_request(gpiomtd->plat.gpio_ale, "NAND ALE"); | 
 | 	if (ret) | 
 | 		goto err_ale; | 
 | 	gpio_direction_output(gpiomtd->plat.gpio_ale, 0); | 
 | 	ret = gpio_request(gpiomtd->plat.gpio_cle, "NAND CLE"); | 
 | 	if (ret) | 
 | 		goto err_cle; | 
 | 	gpio_direction_output(gpiomtd->plat.gpio_cle, 0); | 
 | 	ret = gpio_request(gpiomtd->plat.gpio_rdy, "NAND RDY"); | 
 | 	if (ret) | 
 | 		goto err_rdy; | 
 | 	gpio_direction_input(gpiomtd->plat.gpio_rdy); | 
 |  | 
 |  | 
 | 	this->IO_ADDR_W  = this->IO_ADDR_R; | 
 | 	this->ecc.mode   = NAND_ECC_SOFT; | 
 | 	this->options    = gpiomtd->plat.options; | 
 | 	this->chip_delay = gpiomtd->plat.chip_delay; | 
 |  | 
 | 	/* install our routines */ | 
 | 	this->cmd_ctrl   = gpio_nand_cmd_ctrl; | 
 | 	this->dev_ready  = gpio_nand_devready; | 
 |  | 
 | 	if (this->options & NAND_BUSWIDTH_16) { | 
 | 		this->read_buf   = gpio_nand_readbuf16; | 
 | 		this->write_buf  = gpio_nand_writebuf16; | 
 | 		this->verify_buf = gpio_nand_verifybuf16; | 
 | 	} else { | 
 | 		this->read_buf   = gpio_nand_readbuf; | 
 | 		this->write_buf  = gpio_nand_writebuf; | 
 | 		this->verify_buf = gpio_nand_verifybuf; | 
 | 	} | 
 |  | 
 | 	/* set the mtd private data for the nand driver */ | 
 | 	gpiomtd->mtd_info.priv = this; | 
 | 	gpiomtd->mtd_info.owner = THIS_MODULE; | 
 |  | 
 | 	if (nand_scan(&gpiomtd->mtd_info, 1)) { | 
 | 		dev_err(&dev->dev, "no nand chips found?\n"); | 
 | 		ret = -ENXIO; | 
 | 		goto err_wp; | 
 | 	} | 
 |  | 
 | 	if (gpiomtd->plat.adjust_parts) | 
 | 		gpiomtd->plat.adjust_parts(&gpiomtd->plat, | 
 | 					   gpiomtd->mtd_info.size); | 
 |  | 
 | 	ppdata.of_node = dev->dev.of_node; | 
 | 	ret = mtd_device_parse_register(&gpiomtd->mtd_info, NULL, &ppdata, | 
 | 					gpiomtd->plat.parts, | 
 | 					gpiomtd->plat.num_parts); | 
 | 	if (ret) | 
 | 		goto err_wp; | 
 | 	platform_set_drvdata(dev, gpiomtd); | 
 |  | 
 | 	return 0; | 
 |  | 
 | err_wp: | 
 | 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) | 
 | 		gpio_set_value(gpiomtd->plat.gpio_nwp, 0); | 
 | 	gpio_free(gpiomtd->plat.gpio_rdy); | 
 | err_rdy: | 
 | 	gpio_free(gpiomtd->plat.gpio_cle); | 
 | err_cle: | 
 | 	gpio_free(gpiomtd->plat.gpio_ale); | 
 | err_ale: | 
 | 	if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) | 
 | 		gpio_free(gpiomtd->plat.gpio_nwp); | 
 | err_nwp: | 
 | 	gpio_free(gpiomtd->plat.gpio_nce); | 
 | err_nce: | 
 | 	iounmap(gpiomtd->io_sync); | 
 | 	if (res1) | 
 | 		release_mem_region(res1->start, resource_size(res1)); | 
 | err_sync: | 
 | 	iounmap(gpiomtd->nand_chip.IO_ADDR_R); | 
 | 	release_mem_region(res0->start, resource_size(res0)); | 
 | err_map: | 
 | 	kfree(gpiomtd); | 
 | 	return ret; | 
 | } | 
 |  | 
 | static struct platform_driver gpio_nand_driver = { | 
 | 	.probe		= gpio_nand_probe, | 
 | 	.remove		= gpio_nand_remove, | 
 | 	.driver		= { | 
 | 		.name	= "gpio-nand", | 
 | 		.of_match_table = gpio_nand_id_table, | 
 | 	}, | 
 | }; | 
 |  | 
 | static int __init gpio_nand_init(void) | 
 | { | 
 | 	printk(KERN_INFO "GPIO NAND driver, © 2004 Simtec Electronics\n"); | 
 |  | 
 | 	return platform_driver_register(&gpio_nand_driver); | 
 | } | 
 |  | 
 | static void __exit gpio_nand_exit(void) | 
 | { | 
 | 	platform_driver_unregister(&gpio_nand_driver); | 
 | } | 
 |  | 
 | module_init(gpio_nand_init); | 
 | module_exit(gpio_nand_exit); | 
 |  | 
 | MODULE_LICENSE("GPL"); | 
 | MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); | 
 | MODULE_DESCRIPTION("GPIO NAND Driver"); |