[SCSI] be2iscsi: adding functionality to change network settings using iscsiadm
This patch allows iscsiadm to set/ delete static IP and enable /disable
DHCP.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/be2iscsi/be_main.c b/drivers/scsi/be2iscsi/be_main.c
index ff6f851..0b1d99c 100644
--- a/drivers/scsi/be2iscsi/be_main.c
+++ b/drivers/scsi/be2iscsi/be_main.c
@@ -231,10 +231,10 @@
case ISCSI_BOOT_TGT_IP_ADDR:
if (boot_conn->dest_ipaddr.ip_type == 0x1)
rc = sprintf(buf, "%pI4\n",
- (char *)&boot_conn->dest_ipaddr.ip_address);
+ (char *)&boot_conn->dest_ipaddr.addr);
else
rc = sprintf(str, "%pI6\n",
- (char *)&boot_conn->dest_ipaddr.ip_address);
+ (char *)&boot_conn->dest_ipaddr.addr);
break;
case ISCSI_BOOT_TGT_PORT:
rc = sprintf(str, "%d\n", boot_conn->dest_port);
@@ -312,12 +312,8 @@
rc = sprintf(str, "0\n");
break;
case ISCSI_BOOT_ETH_MAC:
- rc = beiscsi_get_macaddr(buf, phba);
- if (rc < 0) {
- SE_DEBUG(DBG_LVL_1, "beiscsi_get_macaddr Failed\n");
- return rc;
- }
- break;
+ rc = beiscsi_get_macaddr(str, phba);
+ break;
default:
rc = -ENOSYS;
break;
@@ -438,6 +434,7 @@
phba->shost = shost;
phba->pcidev = pci_dev_get(pcidev);
pci_set_drvdata(pcidev, phba);
+ phba->interface_handle = 0xFFFFFFFF;
if (iscsi_host_add(shost, &phba->pcidev->dev))
goto free_devices;
@@ -3471,8 +3468,8 @@
static int beiscsi_get_boot_info(struct beiscsi_hba *phba)
{
- struct be_cmd_resp_get_boot_target *boot_resp;
- struct be_cmd_resp_get_session *session_resp;
+ struct be_cmd_get_boot_target_resp *boot_resp;
+ struct be_cmd_get_session_resp *session_resp;
struct be_mcc_wrb *wrb;
struct be_dma_mem nonemb_cmd;
unsigned int tag, wrb_num;
@@ -3480,9 +3477,9 @@
struct be_queue_info *mccq = &phba->ctrl.mcc_obj.q;
int ret = -ENOMEM;
- tag = beiscsi_get_boot_target(phba);
+ tag = mgmt_get_boot_target(phba);
if (!tag) {
- SE_DEBUG(DBG_LVL_1, "be_cmd_get_mac_addr Failed\n");
+ SE_DEBUG(DBG_LVL_1, "beiscsi_get_boot_info Failed\n");
return -EAGAIN;
} else
wait_event_interruptible(phba->ctrl.mcc_wait[tag],
@@ -3492,7 +3489,7 @@
extd_status = (phba->ctrl.mcc_numtag[tag] & 0x0000FF00) >> 8;
status = phba->ctrl.mcc_numtag[tag] & 0x000000FF;
if (status || extd_status) {
- SE_DEBUG(DBG_LVL_1, "be_cmd_get_mac_addr Failed"
+ SE_DEBUG(DBG_LVL_1, "beiscsi_get_boot_info Failed"
" status = %d extd_status = %d\n",
status, extd_status);
free_mcc_tag(&phba->ctrl, tag);
@@ -3518,8 +3515,8 @@
}
memset(nonemb_cmd.va, 0, sizeof(*session_resp));
- tag = beiscsi_get_session_info(phba,
- boot_resp->boot_session_handle, &nonemb_cmd);
+ tag = mgmt_get_session_info(phba, boot_resp->boot_session_handle,
+ &nonemb_cmd);
if (!tag) {
SE_DEBUG(DBG_LVL_1, "beiscsi_get_session_info"
" Failed\n");
@@ -4267,6 +4264,7 @@
return;
}
+ beiscsi_destroy_def_ifaces(phba);
beiscsi_quiesce(phba);
iscsi_boot_destroy_kset(phba->boot_kset);
iscsi_host_remove(phba->shost);
@@ -4453,8 +4451,9 @@
* iscsi boot.
*/
shost_printk(KERN_ERR, phba->shost, "Could not set up "
- "iSCSI boot info.");
+ "iSCSI boot info.\n");
+ beiscsi_create_def_ifaces(phba);
SE_DEBUG(DBG_LVL_8, "\n\n\n SUCCESS - DRIVER LOADED\n\n\n");
return 0;
@@ -4505,6 +4504,8 @@
.bind_conn = beiscsi_conn_bind,
.destroy_conn = iscsi_conn_teardown,
.attr_is_visible = be2iscsi_attr_is_visible,
+ .set_iface_param = be2iscsi_iface_set_param,
+ .get_iface_param = be2iscsi_iface_get_param,
.set_param = beiscsi_set_param,
.get_conn_param = iscsi_conn_get_param,
.get_session_param = iscsi_session_get_param,