drivers/usb/host/ohci-pxa27x.c - android_kernel_oneplus_msm8996 - Gitiles

 /*
  * OHCI HCD (Host Controller Driver) for USB.
  *
  * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
  * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
  * (C) Copyright 2002 Hewlett-Packard Company
  *
  * Bus Glue for pxa27x
  *
  * Written by Christopher Hoover <ch@hpl.hp.com>
  * Based on fragments of previous driver by Russell King et al.
  *
  * Modified for LH7A404 from ohci-sa1111.c
  *  by Durgesh Pattamatta <pattamattad@sharpsec.com>
  *
  * Modified for pxa27x from ohci-lh7a404.c
  *  by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
  *
  * This file is licenced under the GPL.
  */

 #include <linux/device.h>
 #include <linux/signal.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/of_platform.h>
 #include <linux/of_gpio.h>
 #include <mach/hardware.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>

 /*
  * UHC: USB Host Controller (OHCI-like) register definitions
  */
 #define UHCREV		(0x0000) /* UHC HCI Spec Revision */
 #define UHCHCON		(0x0004) /* UHC Host Control Register */
 #define UHCCOMS		(0x0008) /* UHC Command Status Register */
 #define UHCINTS		(0x000C) /* UHC Interrupt Status Register */
 #define UHCINTE		(0x0010) /* UHC Interrupt Enable */
 #define UHCINTD		(0x0014) /* UHC Interrupt Disable */
 #define UHCHCCA		(0x0018) /* UHC Host Controller Comm. Area */
 #define UHCPCED		(0x001C) /* UHC Period Current Endpt Descr */
 #define UHCCHED		(0x0020) /* UHC Control Head Endpt Descr */
 #define UHCCCED		(0x0024) /* UHC Control Current Endpt Descr */
 #define UHCBHED		(0x0028) /* UHC Bulk Head Endpt Descr */
 #define UHCBCED		(0x002C) /* UHC Bulk Current Endpt Descr */
 #define UHCDHEAD	(0x0030) /* UHC Done Head */
 #define UHCFMI		(0x0034) /* UHC Frame Interval */
 #define UHCFMR		(0x0038) /* UHC Frame Remaining */
 #define UHCFMN		(0x003C) /* UHC Frame Number */
 #define UHCPERS		(0x0040) /* UHC Periodic Start */
 #define UHCLS		(0x0044) /* UHC Low Speed Threshold */

 #define UHCRHDA		(0x0048) /* UHC Root Hub Descriptor A */
 #define UHCRHDA_NOCP	(1 << 12)	/* No over current protection */
 #define UHCRHDA_OCPM	(1 << 11)	/* Over Current Protection Mode */
 #define UHCRHDA_POTPGT(x) \
 			(((x) & 0xff) << 24) /* Power On To Power Good Time */

 #define UHCRHDB		(0x004C) /* UHC Root Hub Descriptor B */
 #define UHCRHS		(0x0050) /* UHC Root Hub Status */
 #define UHCRHPS1	(0x0054) /* UHC Root Hub Port 1 Status */
 #define UHCRHPS2	(0x0058) /* UHC Root Hub Port 2 Status */
 #define UHCRHPS3	(0x005C) /* UHC Root Hub Port 3 Status */

 #define UHCSTAT		(0x0060) /* UHC Status Register */
 #define UHCSTAT_UPS3	(1 << 16)	/* USB Power Sense Port3 */
 #define UHCSTAT_SBMAI	(1 << 15)	/* System Bus Master Abort Interrupt*/
 #define UHCSTAT_SBTAI	(1 << 14)	/* System Bus Target Abort Interrupt*/
 #define UHCSTAT_UPRI	(1 << 13)	/* USB Port Resume Interrupt */
 #define UHCSTAT_UPS2	(1 << 12)	/* USB Power Sense Port 2 */
 #define UHCSTAT_UPS1	(1 << 11)	/* USB Power Sense Port 1 */
 #define UHCSTAT_HTA	(1 << 10)	/* HCI Target Abort */
 #define UHCSTAT_HBA	(1 << 8)	/* HCI Buffer Active */
 #define UHCSTAT_RWUE	(1 << 7)	/* HCI Remote Wake Up Event */

 #define UHCHR           (0x0064) /* UHC Reset Register */
 #define UHCHR_SSEP3	(1 << 11)	/* Sleep Standby Enable for Port3 */
 #define UHCHR_SSEP2	(1 << 10)	/* Sleep Standby Enable for Port2 */
 #define UHCHR_SSEP1	(1 << 9)	/* Sleep Standby Enable for Port1 */
 #define UHCHR_PCPL	(1 << 7)	/* Power control polarity low */
 #define UHCHR_PSPL	(1 << 6)	/* Power sense polarity low */
 #define UHCHR_SSE	(1 << 5)	/* Sleep Standby Enable */
 #define UHCHR_UIT	(1 << 4)	/* USB Interrupt Test */
 #define UHCHR_SSDC	(1 << 3)	/* Simulation Scale Down Clock */
 #define UHCHR_CGR	(1 << 2)	/* Clock Generation Reset */
 #define UHCHR_FHR	(1 << 1)	/* Force Host Controller Reset */
 #define UHCHR_FSBIR	(1 << 0)	/* Force System Bus Iface Reset */

 #define UHCHIE          (0x0068) /* UHC Interrupt Enable Register*/
 #define UHCHIE_UPS3IE	(1 << 14)	/* Power Sense Port3 IntEn */
 #define UHCHIE_UPRIE	(1 << 13)	/* Port Resume IntEn */
 #define UHCHIE_UPS2IE	(1 << 12)	/* Power Sense Port2 IntEn */
 #define UHCHIE_UPS1IE	(1 << 11)	/* Power Sense Port1 IntEn */
 #define UHCHIE_TAIE	(1 << 10)	/* HCI Interface Transfer Abort
 					   Interrupt Enable*/
 #define UHCHIE_HBAIE	(1 << 8)	/* HCI Buffer Active IntEn */
 #define UHCHIE_RWIE	(1 << 7)	/* Remote Wake-up IntEn */

 #define UHCHIT          (0x006C) /* UHC Interrupt Test register */

 #define PXA_UHC_MAX_PORTNUM    3

 struct pxa27x_ohci {
 	/* must be 1st member here for hcd_to_ohci() to work */
 	struct ohci_hcd ohci;

 	struct device	*dev;
 	struct clk	*clk;
 	void __iomem	*mmio_base;
 };

 #define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)hcd_to_ohci(hcd)

 /*
   PMM_NPS_MODE -- PMM Non-power switching mode
       Ports are powered continuously.

   PMM_GLOBAL_MODE -- PMM global switching mode
       All ports are powered at the same time.

   PMM_PERPORT_MODE -- PMM per port switching mode
       Ports are powered individually.
  */
 static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
 {
 	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
 	uint32_t uhcrhdb = __raw_readl(ohci->mmio_base + UHCRHDB);

 	switch (mode) {
 	case PMM_NPS_MODE:
 		uhcrhda |= RH_A_NPS;
 		break;
 	case PMM_GLOBAL_MODE:
 		uhcrhda &= ~(RH_A_NPS & RH_A_PSM);
 		break;
 	case PMM_PERPORT_MODE:
 		uhcrhda &= ~(RH_A_NPS);
 		uhcrhda |= RH_A_PSM;

 		/* Set port power control mask bits, only 3 ports. */
 		uhcrhdb |= (0x7<<17);
 		break;
 	default:
 		printk( KERN_ERR
 			"Invalid mode %d, set to non-power switch mode.\n",
 			mode );

 		uhcrhda |= RH_A_NPS;
 	}

 	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
 	__raw_writel(uhcrhdb, ohci->mmio_base + UHCRHDB);
 	return 0;
 }

 extern int usb_disabled(void);

 /*-------------------------------------------------------------------------*/

 static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
 				   struct pxaohci_platform_data *inf)
 {
 	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
 	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);

 	if (inf->flags & ENABLE_PORT1)
 		uhchr &= ~UHCHR_SSEP1;

 	if (inf->flags & ENABLE_PORT2)
 		uhchr &= ~UHCHR_SSEP2;

 	if (inf->flags & ENABLE_PORT3)
 		uhchr &= ~UHCHR_SSEP3;

 	if (inf->flags & POWER_CONTROL_LOW)
 		uhchr |= UHCHR_PCPL;

 	if (inf->flags & POWER_SENSE_LOW)
 		uhchr |= UHCHR_PSPL;

 	if (inf->flags & NO_OC_PROTECTION)
 		uhcrhda |= UHCRHDA_NOCP;
 	else
 		uhcrhda &= ~UHCRHDA_NOCP;

 	if (inf->flags & OC_MODE_PERPORT)
 		uhcrhda |= UHCRHDA_OCPM;
 	else
 		uhcrhda &= ~UHCRHDA_OCPM;

 	if (inf->power_on_delay) {
 		uhcrhda &= ~UHCRHDA_POTPGT(0xff);
 		uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
 	}

 	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
 	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
 }

 static inline void pxa27x_reset_hc(struct pxa27x_ohci *ohci)
 {
 	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);

 	__raw_writel(uhchr | UHCHR_FHR, ohci->mmio_base + UHCHR);
 	udelay(11);
 	__raw_writel(uhchr & ~UHCHR_FHR, ohci->mmio_base + UHCHR);
 }

 #ifdef CONFIG_PXA27x
 extern void pxa27x_clear_otgph(void);
 #else
 #define pxa27x_clear_otgph()	do {} while (0)
 #endif

 static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev)
 {
 	int retval = 0;
 	struct pxaohci_platform_data *inf;
 	uint32_t uhchr;

 	inf = dev->platform_data;

 	clk_prepare_enable(ohci->clk);

 	pxa27x_reset_hc(ohci);

 	uhchr = __raw_readl(ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
 	__raw_writel(uhchr, ohci->mmio_base + UHCHR);

 	while (__raw_readl(ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
 		cpu_relax();

 	pxa27x_setup_hc(ohci, inf);

 	if (inf->init)
 		retval = inf->init(dev);

 	if (retval < 0)
 		return retval;

 	if (cpu_is_pxa3xx())
 		pxa3xx_u2d_start_hc(&ohci_to_hcd(&ohci->ohci)->self);

 	uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
 	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
 	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, ohci->mmio_base + UHCHIE);

 	/* Clear any OTG Pin Hold */
 	pxa27x_clear_otgph();
 	return 0;
 }

 static void pxa27x_stop_hc(struct pxa27x_ohci *ohci, struct device *dev)
 {
 	struct pxaohci_platform_data *inf;
 	uint32_t uhccoms;

 	inf = dev->platform_data;

 	if (cpu_is_pxa3xx())
 		pxa3xx_u2d_stop_hc(&ohci_to_hcd(&ohci->ohci)->self);

 	if (inf->exit)
 		inf->exit(dev);

 	pxa27x_reset_hc(ohci);

 	/* Host Controller Reset */
 	uhccoms = __raw_readl(ohci->mmio_base + UHCCOMS) | 0x01;
 	__raw_writel(uhccoms, ohci->mmio_base + UHCCOMS);
 	udelay(10);

 	clk_disable_unprepare(ohci->clk);
 }

 #ifdef CONFIG_OF
 static const struct of_device_id pxa_ohci_dt_ids[] = {
 	{ .compatible = "marvell,pxa-ohci" },
 	{ }
 };

 MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);

 static u64 pxa_ohci_dma_mask = DMA_BIT_MASK(32);

 static int __devinit ohci_pxa_of_init(struct platform_device *pdev)
 {
 	struct device_node *np = pdev->dev.of_node;
 	struct pxaohci_platform_data *pdata;
 	u32 tmp;

 	if (!np)
 		return 0;

 	/* Right now device-tree probed devices don't get dma_mask set.
 	 * Since shared usb code relies on it, set it here for now.
 	 * Once we have dma capability bindings this can go away.
 	 */
 	if (!pdev->dev.dma_mask)
 		pdev->dev.dma_mask = &pxa_ohci_dma_mask;

 	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata)
 		return -ENOMEM;

 	if (of_get_property(np, "marvell,enable-port1", NULL))
 		pdata->flags |= ENABLE_PORT1;
 	if (of_get_property(np, "marvell,enable-port2", NULL))
 		pdata->flags |= ENABLE_PORT2;
 	if (of_get_property(np, "marvell,enable-port3", NULL))
 		pdata->flags |= ENABLE_PORT3;
 	if (of_get_property(np, "marvell,port-sense-low", NULL))
 		pdata->flags |= POWER_SENSE_LOW;
 	if (of_get_property(np, "marvell,power-control-low", NULL))
 		pdata->flags |= POWER_CONTROL_LOW;
 	if (of_get_property(np, "marvell,no-oc-protection", NULL))
 		pdata->flags |= NO_OC_PROTECTION;
 	if (of_get_property(np, "marvell,oc-mode-perport", NULL))
 		pdata->flags |= OC_MODE_PERPORT;
 	if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp))
 		pdata->power_on_delay = tmp;
 	if (!of_property_read_u32(np, "marvell,port-mode", &tmp))
 		pdata->port_mode = tmp;
 	if (!of_property_read_u32(np, "marvell,power-budget", &tmp))
 		pdata->power_budget = tmp;

 	pdev->dev.platform_data = pdata;

 	return 0;
 }
 #else
 static int __devinit ohci_pxa_of_init(struct platform_device *pdev)
 {
 	return 0;
 }
 #endif

 /*-------------------------------------------------------------------------*/

 /* configure so an HC device and id are always provided */
 /* always called with process context; sleeping is OK */


 /**
  * usb_hcd_pxa27x_probe - initialize pxa27x-based HCDs
  * Context: !in_interrupt()
  *
  * Allocates basic resources for this USB host controller, and
  * then invokes the start() method for the HCD associated with it
  * through the hotplug entry's driver_data.
  *
  */
 int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device *pdev)
 {
 	int retval, irq;
 	struct usb_hcd *hcd;
 	struct pxaohci_platform_data *inf;
 	struct pxa27x_ohci *ohci;
 	struct resource *r;
 	struct clk *usb_clk;

 	retval = ohci_pxa_of_init(pdev);
 	if (retval)
 		return retval;

 	inf = pdev->dev.platform_data;

 	if (!inf)
 		return -ENODEV;

 	irq = platform_get_irq(pdev, 0);
 	if (irq < 0) {
 		pr_err("no resource of IORESOURCE_IRQ");
 		return -ENXIO;
 	}

 	usb_clk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(usb_clk))
 		return PTR_ERR(usb_clk);

 	hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x");
 	if (!hcd) {
 		retval = -ENOMEM;
 		goto err0;
 	}

 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!r) {
 		pr_err("no resource of IORESOURCE_MEM");
 		retval = -ENXIO;
 		goto err1;
 	}

 	hcd->rsrc_start = r->start;
 	hcd->rsrc_len = resource_size(r);

 	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
 		pr_debug("request_mem_region failed");
 		retval = -EBUSY;
 		goto err1;
 	}

 	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
 	if (!hcd->regs) {
 		pr_debug("ioremap failed");
 		retval = -ENOMEM;
 		goto err2;
 	}

 	/* initialize "struct pxa27x_ohci" */
 	ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd);
 	ohci->dev = &pdev->dev;
 	ohci->clk = usb_clk;
 	ohci->mmio_base = (void __iomem *)hcd->regs;

 	if ((retval = pxa27x_start_hc(ohci, &pdev->dev)) < 0) {
 		pr_debug("pxa27x_start_hc failed");
 		goto err3;
 	}

 	/* Select Power Management Mode */
 	pxa27x_ohci_select_pmm(ohci, inf->port_mode);

 	if (inf->power_budget)
 		hcd->power_budget = inf->power_budget;

 	ohci_hcd_init(hcd_to_ohci(hcd));

 	retval = usb_add_hcd(hcd, irq, 0);
 	if (retval == 0)
 		return retval;

 	pxa27x_stop_hc(ohci, &pdev->dev);
  err3:
 	iounmap(hcd->regs);
  err2:
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
  err1:
 	usb_put_hcd(hcd);
  err0:
 	clk_put(usb_clk);
 	return retval;
 }


 /* may be called without controller electrically present */
 /* may be called with controller, bus, and devices active */

 /**
  * usb_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
  * @dev: USB Host Controller being removed
  * Context: !in_interrupt()
  *
  * Reverses the effect of usb_hcd_pxa27x_probe(), first invoking
  * the HCD's stop() method.  It is always called from a thread
  * context, normally "rmmod", "apmd", or something similar.
  *
  */
 void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev)
 {
 	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);

 	usb_remove_hcd(hcd);
 	pxa27x_stop_hc(ohci, &pdev->dev);
 	iounmap(hcd->regs);
 	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
 	usb_put_hcd(hcd);
 	clk_put(ohci->clk);
 }

 /*-------------------------------------------------------------------------*/

 static int __devinit
 ohci_pxa27x_start (struct usb_hcd *hcd)
 {
 	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
 	int		ret;

 	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);

 	/* The value of NDP in roothub_a is incorrect on this hardware */
 	ohci->num_ports = 3;

 	if ((ret = ohci_init(ohci)) < 0)
 		return ret;

 	if ((ret = ohci_run (ohci)) < 0) {
 		dev_err(hcd->self.controller, "can't start %s",
 			hcd->self.bus_name);
 		ohci_stop (hcd);
 		return ret;
 	}

 	return 0;
 }

 /*-------------------------------------------------------------------------*/

 static const struct hc_driver ohci_pxa27x_hc_driver = {
 	.description =		hcd_name,
 	.product_desc =		"PXA27x OHCI",
 	.hcd_priv_size =	sizeof(struct pxa27x_ohci),

 	/*
 	 * generic hardware linkage
 	 */
 	.irq =			ohci_irq,
 	.flags =		HCD_USB11 | HCD_MEMORY,

 	/*
 	 * basic lifecycle operations
 	 */
 	.start =		ohci_pxa27x_start,
 	.stop =			ohci_stop,
 	.shutdown =		ohci_shutdown,

 	/*
 	 * managing i/o requests and associated device resources
 	 */
 	.urb_enqueue =		ohci_urb_enqueue,
 	.urb_dequeue =		ohci_urb_dequeue,
 	.endpoint_disable =	ohci_endpoint_disable,

 	/*
 	 * scheduling support
 	 */
 	.get_frame_number =	ohci_get_frame,

 	/*
 	 * root hub support
 	 */
 	.hub_status_data =	ohci_hub_status_data,
 	.hub_control =		ohci_hub_control,
 #ifdef  CONFIG_PM
 	.bus_suspend =		ohci_bus_suspend,
 	.bus_resume =		ohci_bus_resume,
 #endif
 	.start_port_reset =	ohci_start_port_reset,
 };

 /*-------------------------------------------------------------------------*/

 static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
 {
 	pr_debug ("In ohci_hcd_pxa27x_drv_probe");

 	if (usb_disabled())
 		return -ENODEV;

 	return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev);
 }

 static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
 {
 	struct usb_hcd *hcd = platform_get_drvdata(pdev);

 	usb_hcd_pxa27x_remove(hcd, pdev);
 	platform_set_drvdata(pdev, NULL);
 	return 0;
 }

 #ifdef CONFIG_PM
 static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
 {
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);

 	if (time_before(jiffies, ohci->ohci.next_statechange))
 		msleep(5);
 	ohci->ohci.next_statechange = jiffies;

 	pxa27x_stop_hc(ohci, dev);
 	return 0;
 }

 static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
 {
 	struct usb_hcd *hcd = dev_get_drvdata(dev);
 	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
 	struct pxaohci_platform_data *inf = dev->platform_data;
 	int status;

 	if (time_before(jiffies, ohci->ohci.next_statechange))
 		msleep(5);
 	ohci->ohci.next_statechange = jiffies;

 	if ((status = pxa27x_start_hc(ohci, dev)) < 0)
 		return status;

 	/* Select Power Management Mode */
 	pxa27x_ohci_select_pmm(ohci, inf->port_mode);

 	ohci_finish_controller_resume(hcd);
 	return 0;
 }

 static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
 	.suspend	= ohci_hcd_pxa27x_drv_suspend,
 	.resume		= ohci_hcd_pxa27x_drv_resume,
 };
 #endif

 /* work with hotplug and coldplug */
 MODULE_ALIAS("platform:pxa27x-ohci");

 static struct platform_driver ohci_hcd_pxa27x_driver = {
 	.probe		= ohci_hcd_pxa27x_drv_probe,
 	.remove		= ohci_hcd_pxa27x_drv_remove,
 	.shutdown	= usb_hcd_platform_shutdown,
 	.driver		= {
 		.name	= "pxa27x-ohci",
 		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(pxa_ohci_dt_ids),
 #ifdef CONFIG_PM
 		.pm	= &ohci_hcd_pxa27x_pm_ops,
 #endif
 	},
 };
	/*
	* OHCI HCD (Host Controller Driver) for USB.
	*
	* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
	* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
	* (C) Copyright 2002 Hewlett-Packard Company
	*
	* Bus Glue for pxa27x
	*
	* Written by Christopher Hoover <ch@hpl.hp.com>
	* Based on fragments of previous driver by Russell King et al.
	*
	* Modified for LH7A404 from ohci-sa1111.c
	* by Durgesh Pattamatta <pattamattad@sharpsec.com>
	*
	* Modified for pxa27x from ohci-lh7a404.c
	* by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
	*
	* This file is licenced under the GPL.
	*/

	#include <linux/device.h>
	#include <linux/signal.h>
	#include <linux/platform_device.h>
	#include <linux/clk.h>
	#include <linux/of_platform.h>
	#include <linux/of_gpio.h>
	#include <mach/hardware.h>
	#include <linux/platform_data/usb-ohci-pxa27x.h>
	#include <linux/platform_data/usb-pxa3xx-ulpi.h>

	/*
	* UHC: USB Host Controller (OHCI-like) register definitions
	*/
	#define UHCREV (0x0000) /* UHC HCI Spec Revision */
	#define UHCHCON (0x0004) /* UHC Host Control Register */
	#define UHCCOMS (0x0008) /* UHC Command Status Register */
	#define UHCINTS (0x000C) /* UHC Interrupt Status Register */
	#define UHCINTE (0x0010) /* UHC Interrupt Enable */
	#define UHCINTD (0x0014) /* UHC Interrupt Disable */
	#define UHCHCCA (0x0018) /* UHC Host Controller Comm. Area */
	#define UHCPCED (0x001C) /* UHC Period Current Endpt Descr */
	#define UHCCHED (0x0020) /* UHC Control Head Endpt Descr */
	#define UHCCCED (0x0024) /* UHC Control Current Endpt Descr */
	#define UHCBHED (0x0028) /* UHC Bulk Head Endpt Descr */
	#define UHCBCED (0x002C) /* UHC Bulk Current Endpt Descr */
	#define UHCDHEAD (0x0030) /* UHC Done Head */
	#define UHCFMI (0x0034) /* UHC Frame Interval */
	#define UHCFMR (0x0038) /* UHC Frame Remaining */
	#define UHCFMN (0x003C) /* UHC Frame Number */
	#define UHCPERS (0x0040) /* UHC Periodic Start */
	#define UHCLS (0x0044) /* UHC Low Speed Threshold */

	#define UHCRHDA (0x0048) /* UHC Root Hub Descriptor A */
	#define UHCRHDA_NOCP (1 << 12) /* No over current protection */
	#define UHCRHDA_OCPM (1 << 11) /* Over Current Protection Mode */
	#define UHCRHDA_POTPGT(x) \
	(((x) & 0xff) << 24) /* Power On To Power Good Time */

	#define UHCRHDB (0x004C) /* UHC Root Hub Descriptor B */
	#define UHCRHS (0x0050) /* UHC Root Hub Status */
	#define UHCRHPS1 (0x0054) /* UHC Root Hub Port 1 Status */
	#define UHCRHPS2 (0x0058) /* UHC Root Hub Port 2 Status */
	#define UHCRHPS3 (0x005C) /* UHC Root Hub Port 3 Status */

	#define UHCSTAT (0x0060) /* UHC Status Register */
	#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */
	#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/
	#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/
	#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */
	#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */
	#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */
	#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */
	#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */
	#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */

	#define UHCHR (0x0064) /* UHC Reset Register */
	#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */
	#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */
	#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */
	#define UHCHR_PCPL (1 << 7) /* Power control polarity low */
	#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */
	#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */
	#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */
	#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */
	#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */
	#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */
	#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */

	#define UHCHIE (0x0068) /* UHC Interrupt Enable Register*/
	#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */
	#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */
	#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */
	#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */
	#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort
	Interrupt Enable*/
	#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */
	#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */

	#define UHCHIT (0x006C) /* UHC Interrupt Test register */

	#define PXA_UHC_MAX_PORTNUM 3

	struct pxa27x_ohci {
	/* must be 1st member here for hcd_to_ohci() to work */
	struct ohci_hcd ohci;

	struct device *dev;
	struct clk *clk;
	void __iomem *mmio_base;
	};

	#define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)hcd_to_ohci(hcd)

	/*
	PMM_NPS_MODE -- PMM Non-power switching mode
	Ports are powered continuously.

	PMM_GLOBAL_MODE -- PMM global switching mode
	All ports are powered at the same time.

	PMM_PERPORT_MODE -- PMM per port switching mode
	Ports are powered individually.
	*/
	static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode)
	{
	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);
	uint32_t uhcrhdb = __raw_readl(ohci->mmio_base + UHCRHDB);

	switch (mode) {
	case PMM_NPS_MODE:
	uhcrhda \|= RH_A_NPS;
	break;
	case PMM_GLOBAL_MODE:
	uhcrhda &= ~(RH_A_NPS & RH_A_PSM);
	break;
	case PMM_PERPORT_MODE:
	uhcrhda &= ~(RH_A_NPS);
	uhcrhda \|= RH_A_PSM;

	/* Set port power control mask bits, only 3 ports. */
	uhcrhdb \|= (0x7<<17);
	break;
	default:
	printk( KERN_ERR
	"Invalid mode %d, set to non-power switch mode.\n",
	mode );

	uhcrhda \|= RH_A_NPS;
	}

	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
	__raw_writel(uhcrhdb, ohci->mmio_base + UHCRHDB);
	return 0;
	}

	extern int usb_disabled(void);

	/-------------------------------------------------------------------------/

	static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci,
	struct pxaohci_platform_data *inf)
	{
	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);
	uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA);

	if (inf->flags & ENABLE_PORT1)
	uhchr &= ~UHCHR_SSEP1;

	if (inf->flags & ENABLE_PORT2)
	uhchr &= ~UHCHR_SSEP2;

	if (inf->flags & ENABLE_PORT3)
	uhchr &= ~UHCHR_SSEP3;

	if (inf->flags & POWER_CONTROL_LOW)
	uhchr \|= UHCHR_PCPL;

	if (inf->flags & POWER_SENSE_LOW)
	uhchr \|= UHCHR_PSPL;

	if (inf->flags & NO_OC_PROTECTION)
	uhcrhda \|= UHCRHDA_NOCP;
	else
	uhcrhda &= ~UHCRHDA_NOCP;

	if (inf->flags & OC_MODE_PERPORT)
	uhcrhda \|= UHCRHDA_OCPM;
	else
	uhcrhda &= ~UHCRHDA_OCPM;

	if (inf->power_on_delay) {
	uhcrhda &= ~UHCRHDA_POTPGT(0xff);
	uhcrhda \|= UHCRHDA_POTPGT(inf->power_on_delay / 2);
	}

	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
	__raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA);
	}

	static inline void pxa27x_reset_hc(struct pxa27x_ohci *ohci)
	{
	uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR);

	__raw_writel(uhchr \| UHCHR_FHR, ohci->mmio_base + UHCHR);
	udelay(11);
	__raw_writel(uhchr & ~UHCHR_FHR, ohci->mmio_base + UHCHR);
	}

	#ifdef CONFIG_PXA27x
	extern void pxa27x_clear_otgph(void);
	#else
	#define pxa27x_clear_otgph() do {} while (0)
	#endif

	static int pxa27x_start_hc(struct pxa27x_ohci ohci, struct device dev)
	{
	int retval = 0;
	struct pxaohci_platform_data *inf;
	uint32_t uhchr;

	inf = dev->platform_data;

	clk_prepare_enable(ohci->clk);

	pxa27x_reset_hc(ohci);

	uhchr = __raw_readl(ohci->mmio_base + UHCHR) \| UHCHR_FSBIR;
	__raw_writel(uhchr, ohci->mmio_base + UHCHR);

	while (__raw_readl(ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
	cpu_relax();

	pxa27x_setup_hc(ohci, inf);

	if (inf->init)
	retval = inf->init(dev);

	if (retval < 0)
	return retval;

	if (cpu_is_pxa3xx())
	pxa3xx_u2d_start_hc(&ohci_to_hcd(&ohci->ohci)->self);

	uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
	__raw_writel(uhchr, ohci->mmio_base + UHCHR);
	__raw_writel(UHCHIE_UPRIE \| UHCHIE_RWIE, ohci->mmio_base + UHCHIE);

	/* Clear any OTG Pin Hold */
	pxa27x_clear_otgph();
	return 0;
	}

	static void pxa27x_stop_hc(struct pxa27x_ohci ohci, struct device dev)
	{
	struct pxaohci_platform_data *inf;
	uint32_t uhccoms;

	inf = dev->platform_data;

	if (cpu_is_pxa3xx())
	pxa3xx_u2d_stop_hc(&ohci_to_hcd(&ohci->ohci)->self);

	if (inf->exit)
	inf->exit(dev);

	pxa27x_reset_hc(ohci);

	/* Host Controller Reset */
	uhccoms = __raw_readl(ohci->mmio_base + UHCCOMS) \| 0x01;
	__raw_writel(uhccoms, ohci->mmio_base + UHCCOMS);
	udelay(10);

	clk_disable_unprepare(ohci->clk);
	}

	#ifdef CONFIG_OF
	static const struct of_device_id pxa_ohci_dt_ids[] = {
	{ .compatible = "marvell,pxa-ohci" },
	{ }
	};

	MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);

	static u64 pxa_ohci_dma_mask = DMA_BIT_MASK(32);

	static int __devinit ohci_pxa_of_init(struct platform_device *pdev)
	{
	struct device_node *np = pdev->dev.of_node;
	struct pxaohci_platform_data *pdata;
	u32 tmp;

	if (!np)
	return 0;

	/* Right now device-tree probed devices don't get dma_mask set.
	* Since shared usb code relies on it, set it here for now.
	* Once we have dma capability bindings this can go away.
	*/
	if (!pdev->dev.dma_mask)
	pdev->dev.dma_mask = &pxa_ohci_dma_mask;

	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
	if (!pdata)
	return -ENOMEM;

	if (of_get_property(np, "marvell,enable-port1", NULL))
	pdata->flags \|= ENABLE_PORT1;
	if (of_get_property(np, "marvell,enable-port2", NULL))
	pdata->flags \|= ENABLE_PORT2;
	if (of_get_property(np, "marvell,enable-port3", NULL))
	pdata->flags \|= ENABLE_PORT3;
	if (of_get_property(np, "marvell,port-sense-low", NULL))
	pdata->flags \|= POWER_SENSE_LOW;
	if (of_get_property(np, "marvell,power-control-low", NULL))
	pdata->flags \|= POWER_CONTROL_LOW;
	if (of_get_property(np, "marvell,no-oc-protection", NULL))
	pdata->flags \|= NO_OC_PROTECTION;
	if (of_get_property(np, "marvell,oc-mode-perport", NULL))
	pdata->flags \|= OC_MODE_PERPORT;
	if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp))
	pdata->power_on_delay = tmp;
	if (!of_property_read_u32(np, "marvell,port-mode", &tmp))
	pdata->port_mode = tmp;
	if (!of_property_read_u32(np, "marvell,power-budget", &tmp))
	pdata->power_budget = tmp;

	pdev->dev.platform_data = pdata;

	return 0;
	}
	#else
	static int __devinit ohci_pxa_of_init(struct platform_device *pdev)
	{
	return 0;
	}
	#endif

	/-------------------------------------------------------------------------/

	/* configure so an HC device and id are always provided */
	/* always called with process context; sleeping is OK */


	/**
	* usb_hcd_pxa27x_probe - initialize pxa27x-based HCDs
	* Context: !in_interrupt()
	*
	* Allocates basic resources for this USB host controller, and
	* then invokes the start() method for the HCD associated with it
	* through the hotplug entry's driver_data.
	*
	*/
	int usb_hcd_pxa27x_probe (const struct hc_driver driver, struct platform_device pdev)
	{
	int retval, irq;
	struct usb_hcd *hcd;
	struct pxaohci_platform_data *inf;
	struct pxa27x_ohci *ohci;
	struct resource *r;
	struct clk *usb_clk;

	retval = ohci_pxa_of_init(pdev);
	if (retval)
	return retval;

	inf = pdev->dev.platform_data;

	if (!inf)
	return -ENODEV;

	irq = platform_get_irq(pdev, 0);
	if (irq < 0) {
	pr_err("no resource of IORESOURCE_IRQ");
	return -ENXIO;
	}

	usb_clk = clk_get(&pdev->dev, NULL);
	if (IS_ERR(usb_clk))
	return PTR_ERR(usb_clk);

	hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x");
	if (!hcd) {
	retval = -ENOMEM;
	goto err0;
	}

	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!r) {
	pr_err("no resource of IORESOURCE_MEM");
	retval = -ENXIO;
	goto err1;
	}

	hcd->rsrc_start = r->start;
	hcd->rsrc_len = resource_size(r);

	if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
	pr_debug("request_mem_region failed");
	retval = -EBUSY;
	goto err1;
	}

	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
	if (!hcd->regs) {
	pr_debug("ioremap failed");
	retval = -ENOMEM;
	goto err2;
	}

	/* initialize "struct pxa27x_ohci" */
	ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd);
	ohci->dev = &pdev->dev;
	ohci->clk = usb_clk;
	ohci->mmio_base = (void __iomem *)hcd->regs;

	if ((retval = pxa27x_start_hc(ohci, &pdev->dev)) < 0) {
	pr_debug("pxa27x_start_hc failed");
	goto err3;
	}

	/* Select Power Management Mode */
	pxa27x_ohci_select_pmm(ohci, inf->port_mode);

	if (inf->power_budget)
	hcd->power_budget = inf->power_budget;

	ohci_hcd_init(hcd_to_ohci(hcd));

	retval = usb_add_hcd(hcd, irq, 0);
	if (retval == 0)
	return retval;

	pxa27x_stop_hc(ohci, &pdev->dev);
	err3:
	iounmap(hcd->regs);
	err2:
	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
	err1:
	usb_put_hcd(hcd);
	err0:
	clk_put(usb_clk);
	return retval;
	}


	/* may be called without controller electrically present */
	/* may be called with controller, bus, and devices active */

	/**
	* usb_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
	* @dev: USB Host Controller being removed
	* Context: !in_interrupt()
	*
	* Reverses the effect of usb_hcd_pxa27x_probe(), first invoking
	* the HCD's stop() method. It is always called from a thread
	* context, normally "rmmod", "apmd", or something similar.
	*
	*/
	void usb_hcd_pxa27x_remove (struct usb_hcd hcd, struct platform_device pdev)
	{
	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);

	usb_remove_hcd(hcd);
	pxa27x_stop_hc(ohci, &pdev->dev);
	iounmap(hcd->regs);
	release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
	usb_put_hcd(hcd);
	clk_put(ohci->clk);
	}

	/-------------------------------------------------------------------------/

	static int __devinit
	ohci_pxa27x_start (struct usb_hcd *hcd)
	{
	struct ohci_hcd *ohci = hcd_to_ohci (hcd);
	int ret;

	ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci);

	/* The value of NDP in roothub_a is incorrect on this hardware */
	ohci->num_ports = 3;

	if ((ret = ohci_init(ohci)) < 0)
	return ret;

	if ((ret = ohci_run (ohci)) < 0) {
	dev_err(hcd->self.controller, "can't start %s",
	hcd->self.bus_name);
	ohci_stop (hcd);
	return ret;
	}

	return 0;
	}

	/-------------------------------------------------------------------------/

	static const struct hc_driver ohci_pxa27x_hc_driver = {
	.description = hcd_name,
	.product_desc = "PXA27x OHCI",
	.hcd_priv_size = sizeof(struct pxa27x_ohci),

	/*
	* generic hardware linkage
	*/
	.irq = ohci_irq,
	.flags = HCD_USB11 \| HCD_MEMORY,

	/*
	* basic lifecycle operations
	*/
	.start = ohci_pxa27x_start,
	.stop = ohci_stop,
	.shutdown = ohci_shutdown,

	/*
	* managing i/o requests and associated device resources
	*/
	.urb_enqueue = ohci_urb_enqueue,
	.urb_dequeue = ohci_urb_dequeue,
	.endpoint_disable = ohci_endpoint_disable,

	/*
	* scheduling support
	*/
	.get_frame_number = ohci_get_frame,

	/*
	* root hub support
	*/
	.hub_status_data = ohci_hub_status_data,
	.hub_control = ohci_hub_control,
	#ifdef CONFIG_PM
	.bus_suspend = ohci_bus_suspend,
	.bus_resume = ohci_bus_resume,
	#endif
	.start_port_reset = ohci_start_port_reset,
	};

	/-------------------------------------------------------------------------/

	static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev)
	{
	pr_debug ("In ohci_hcd_pxa27x_drv_probe");

	if (usb_disabled())
	return -ENODEV;

	return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev);
	}

	static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev)
	{
	struct usb_hcd *hcd = platform_get_drvdata(pdev);

	usb_hcd_pxa27x_remove(hcd, pdev);
	platform_set_drvdata(pdev, NULL);
	return 0;
	}

	#ifdef CONFIG_PM
	static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
	{
	struct usb_hcd *hcd = dev_get_drvdata(dev);
	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);

	if (time_before(jiffies, ohci->ohci.next_statechange))
	msleep(5);
	ohci->ohci.next_statechange = jiffies;

	pxa27x_stop_hc(ohci, dev);
	return 0;
	}

	static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
	{
	struct usb_hcd *hcd = dev_get_drvdata(dev);
	struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd);
	struct pxaohci_platform_data *inf = dev->platform_data;
	int status;

	if (time_before(jiffies, ohci->ohci.next_statechange))
	msleep(5);
	ohci->ohci.next_statechange = jiffies;

	if ((status = pxa27x_start_hc(ohci, dev)) < 0)
	return status;

	/* Select Power Management Mode */
	pxa27x_ohci_select_pmm(ohci, inf->port_mode);

	ohci_finish_controller_resume(hcd);
	return 0;
	}

	static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
	.suspend = ohci_hcd_pxa27x_drv_suspend,
	.resume = ohci_hcd_pxa27x_drv_resume,
	};
	#endif

	/* work with hotplug and coldplug */
	MODULE_ALIAS("platform:pxa27x-ohci");

	static struct platform_driver ohci_hcd_pxa27x_driver = {
	.probe = ohci_hcd_pxa27x_drv_probe,
	.remove = ohci_hcd_pxa27x_drv_remove,
	.shutdown = usb_hcd_platform_shutdown,
	.driver = {
	.name = "pxa27x-ohci",
	.owner = THIS_MODULE,
	.of_match_table = of_match_ptr(pxa_ohci_dt_ids),
	#ifdef CONFIG_PM
	.pm = &ohci_hcd_pxa27x_pm_ops,
	#endif
	},
	};