| /* |
| * include/linux/mfd/asic3.h |
| * |
| * Compaq ASIC3 headers. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * Copyright 2001 Compaq Computer Corporation. |
| * Copyright 2007-2008 OpenedHand Ltd. |
| */ |
| |
| #ifndef __ASIC3_H__ |
| #define __ASIC3_H__ |
| |
| #include <linux/types.h> |
| |
| struct asic3_platform_data { |
| u16 *gpio_config; |
| unsigned int gpio_config_num; |
| |
| unsigned int irq_base; |
| |
| unsigned int gpio_base; |
| }; |
| |
| #define ASIC3_NUM_GPIO_BANKS 4 |
| #define ASIC3_GPIOS_PER_BANK 16 |
| #define ASIC3_NUM_GPIOS 64 |
| #define ASIC3_NR_IRQS ASIC3_NUM_GPIOS + 6 |
| |
| #define ASIC3_IRQ_LED0 64 |
| #define ASIC3_IRQ_LED1 65 |
| #define ASIC3_IRQ_LED2 66 |
| #define ASIC3_IRQ_SPI 67 |
| #define ASIC3_IRQ_SMBUS 68 |
| #define ASIC3_IRQ_OWM 69 |
| |
| #define ASIC3_TO_GPIO(gpio) (NR_BUILTIN_GPIO + (gpio)) |
| |
| #define ASIC3_GPIO_BANK_A 0 |
| #define ASIC3_GPIO_BANK_B 1 |
| #define ASIC3_GPIO_BANK_C 2 |
| #define ASIC3_GPIO_BANK_D 3 |
| |
| #define ASIC3_GPIO(bank, gpio) \ |
| ((ASIC3_GPIOS_PER_BANK * ASIC3_GPIO_BANK_##bank) + (gpio)) |
| #define ASIC3_GPIO_bit(gpio) (1 << (gpio & 0xf)) |
| /* All offsets below are specified with this address bus shift */ |
| #define ASIC3_DEFAULT_ADDR_SHIFT 2 |
| |
| #define ASIC3_OFFSET(base, reg) (ASIC3_##base##_BASE + ASIC3_##base##_##reg) |
| #define ASIC3_GPIO_OFFSET(base, reg) \ |
| (ASIC3_GPIO_##base##_BASE + ASIC3_GPIO_##reg) |
| |
| #define ASIC3_GPIO_A_BASE 0x0000 |
| #define ASIC3_GPIO_B_BASE 0x0100 |
| #define ASIC3_GPIO_C_BASE 0x0200 |
| #define ASIC3_GPIO_D_BASE 0x0300 |
| |
| #define ASIC3_GPIO_TO_BANK(gpio) ((gpio) >> 4) |
| #define ASIC3_GPIO_TO_BIT(gpio) ((gpio) - \ |
| (ASIC3_GPIOS_PER_BANK * ((gpio) >> 4))) |
| #define ASIC3_GPIO_TO_MASK(gpio) (1 << ASIC3_GPIO_TO_BIT(gpio)) |
| #define ASIC3_GPIO_TO_BASE(gpio) (ASIC3_GPIO_A_BASE + (((gpio) >> 4) * 0x0100)) |
| #define ASIC3_BANK_TO_BASE(bank) (ASIC3_GPIO_A_BASE + ((bank) * 0x100)) |
| |
| #define ASIC3_GPIO_MASK 0x00 /* R/W 0:don't mask */ |
| #define ASIC3_GPIO_DIRECTION 0x04 /* R/W 0:input */ |
| #define ASIC3_GPIO_OUT 0x08 /* R/W 0:output low */ |
| #define ASIC3_GPIO_TRIGGER_TYPE 0x0c /* R/W 0:level */ |
| #define ASIC3_GPIO_EDGE_TRIGGER 0x10 /* R/W 0:falling */ |
| #define ASIC3_GPIO_LEVEL_TRIGGER 0x14 /* R/W 0:low level detect */ |
| #define ASIC3_GPIO_SLEEP_MASK 0x18 /* R/W 0:don't mask in sleep mode */ |
| #define ASIC3_GPIO_SLEEP_OUT 0x1c /* R/W level 0:low in sleep mode */ |
| #define ASIC3_GPIO_BAT_FAULT_OUT 0x20 /* R/W level 0:low in batt_fault */ |
| #define ASIC3_GPIO_INT_STATUS 0x24 /* R/W 0:none, 1:detect */ |
| #define ASIC3_GPIO_ALT_FUNCTION 0x28 /* R/W 1:LED register control */ |
| #define ASIC3_GPIO_SLEEP_CONF 0x2c /* |
| * R/W bit 1: autosleep |
| * 0: disable gposlpout in normal mode, |
| * enable gposlpout in sleep mode. |
| */ |
| #define ASIC3_GPIO_STATUS 0x30 /* R Pin status */ |
| |
| /* |
| * ASIC3 GPIO config |
| * |
| * Bits 0..6 gpio number |
| * Bits 7..13 Alternate function |
| * Bit 14 Direction |
| * Bit 15 Initial value |
| * |
| */ |
| #define ASIC3_CONFIG_GPIO_PIN(config) ((config) & 0x7f) |
| #define ASIC3_CONFIG_GPIO_ALT(config) (((config) & (0x7f << 7)) >> 7) |
| #define ASIC3_CONFIG_GPIO_DIR(config) ((config & (1 << 14)) >> 14) |
| #define ASIC3_CONFIG_GPIO_INIT(config) ((config & (1 << 15)) >> 15) |
| #define ASIC3_CONFIG_GPIO(gpio, alt, dir, init) (((gpio) & 0x7f) \ |
| | (((alt) & 0x7f) << 7) | (((dir) & 0x1) << 14) \ |
| | (((init) & 0x1) << 15)) |
| #define ASIC3_CONFIG_GPIO_DEFAULT(gpio, dir, init) \ |
| ASIC3_CONFIG_GPIO((gpio), 0, (dir), (init)) |
| #define ASIC3_CONFIG_GPIO_DEFAULT_OUT(gpio, init) \ |
| ASIC3_CONFIG_GPIO((gpio), 0, 1, (init)) |
| |
| /* |
| * Alternate functions |
| */ |
| #define ASIC3_GPIOA11_PWM0 ASIC3_CONFIG_GPIO(11, 1, 1, 0) |
| #define ASIC3_GPIOA12_PWM1 ASIC3_CONFIG_GPIO(12, 1, 1, 0) |
| #define ASIC3_GPIOA15_CONTROL_CX ASIC3_CONFIG_GPIO(15, 1, 1, 0) |
| #define ASIC3_GPIOC0_LED0 ASIC3_CONFIG_GPIO(32, 1, 1, 0) |
| #define ASIC3_GPIOC1_LED1 ASIC3_CONFIG_GPIO(33, 1, 1, 0) |
| #define ASIC3_GPIOC2_LED2 ASIC3_CONFIG_GPIO(34, 1, 1, 0) |
| #define ASIC3_GPIOC3_SPI_RXD ASIC3_CONFIG_GPIO(35, 1, 0, 0) |
| #define ASIC3_GPIOC4_CF_nCD ASIC3_CONFIG_GPIO(36, 1, 0, 0) |
| #define ASIC3_GPIOC4_SPI_TXD ASIC3_CONFIG_GPIO(36, 1, 1, 0) |
| #define ASIC3_GPIOC5_SPI_CLK ASIC3_CONFIG_GPIO(37, 1, 1, 0) |
| #define ASIC3_GPIOC5_nCIOW ASIC3_CONFIG_GPIO(37, 1, 1, 0) |
| #define ASIC3_GPIOC6_nCIOR ASIC3_CONFIG_GPIO(38, 1, 1, 0) |
| #define ASIC3_GPIOC7_nPCE_1 ASIC3_CONFIG_GPIO(39, 1, 0, 0) |
| #define ASIC3_GPIOC8_nPCE_2 ASIC3_CONFIG_GPIO(40, 1, 0, 0) |
| #define ASIC3_GPIOC9_nPOE ASIC3_CONFIG_GPIO(41, 1, 0, 0) |
| #define ASIC3_GPIOC10_nPWE ASIC3_CONFIG_GPIO(42, 1, 0, 0) |
| #define ASIC3_GPIOC11_PSKTSEL ASIC3_CONFIG_GPIO(43, 1, 0, 0) |
| #define ASIC3_GPIOC12_nPREG ASIC3_CONFIG_GPIO(44, 1, 0, 0) |
| #define ASIC3_GPIOC13_nPWAIT ASIC3_CONFIG_GPIO(45, 1, 1, 0) |
| #define ASIC3_GPIOC14_nPIOIS16 ASIC3_CONFIG_GPIO(46, 1, 1, 0) |
| #define ASIC3_GPIOC15_nPIOR ASIC3_CONFIG_GPIO(47, 1, 0, 0) |
| #define ASIC3_GPIOD11_nCIOIS16 ASIC3_CONFIG_GPIO(59, 1, 0, 0) |
| #define ASIC3_GPIOD12_nCWAIT ASIC3_CONFIG_GPIO(60, 1, 0, 0) |
| #define ASIC3_GPIOD15_nPIOW ASIC3_CONFIG_GPIO(63, 1, 0, 0) |
| |
| |
| #define ASIC3_SPI_Base 0x0400 |
| #define ASIC3_SPI_Control 0x0000 |
| #define ASIC3_SPI_TxData 0x0004 |
| #define ASIC3_SPI_RxData 0x0008 |
| #define ASIC3_SPI_Int 0x000c |
| #define ASIC3_SPI_Status 0x0010 |
| |
| #define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */ |
| |
| #define ASIC3_PWM_0_Base 0x0500 |
| #define ASIC3_PWM_1_Base 0x0600 |
| #define ASIC3_PWM_TimeBase 0x0000 |
| #define ASIC3_PWM_PeriodTime 0x0004 |
| #define ASIC3_PWM_DutyTime 0x0008 |
| |
| #define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */ |
| #define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */ |
| |
| #define ASIC3_LED_0_Base 0x0700 |
| #define ASIC3_LED_1_Base 0x0800 |
| #define ASIC3_LED_2_Base 0x0900 |
| #define ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */ |
| #define ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */ |
| #define ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */ |
| #define ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */ |
| |
| /* LED TimeBase bits - match ASIC2 */ |
| #define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */ |
| /* Note: max = 5 on hx4700 */ |
| /* 0: maximum time base */ |
| /* 1: maximum time base / 2 */ |
| /* n: maximum time base / 2^n */ |
| |
| #define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */ |
| #define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */ |
| #define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */ |
| |
| #define ASIC3_CLOCK_BASE 0x0A00 |
| #define ASIC3_CLOCK_CDEX 0x00 |
| #define ASIC3_CLOCK_SEL 0x04 |
| |
| #define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */ |
| #define CLOCK_CDEX_SOURCE0 (1 << 0) |
| #define CLOCK_CDEX_SOURCE1 (1 << 1) |
| #define CLOCK_CDEX_SPI (1 << 2) |
| #define CLOCK_CDEX_OWM (1 << 3) |
| #define CLOCK_CDEX_PWM0 (1 << 4) |
| #define CLOCK_CDEX_PWM1 (1 << 5) |
| #define CLOCK_CDEX_LED0 (1 << 6) |
| #define CLOCK_CDEX_LED1 (1 << 7) |
| #define CLOCK_CDEX_LED2 (1 << 8) |
| |
| /* Clocks settings: 1 for 24.576 MHz, 0 for 12.288Mhz */ |
| #define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source */ |
| #define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source ctrl */ |
| #define CLOCK_CDEX_SMBUS (1 << 11) |
| #define CLOCK_CDEX_CONTROL_CX (1 << 12) |
| |
| #define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */ |
| #define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */ |
| |
| #define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select */ |
| #define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select */ |
| |
| /* R/W: INT clock source control (32.768 kHz) */ |
| #define CLOCK_SEL_CX (1 << 2) |
| |
| |
| #define ASIC3_INTR_BASE 0x0B00 |
| |
| #define ASIC3_INTR_INT_MASK 0x00 /* Interrupt mask control */ |
| #define ASIC3_INTR_P_INT_STAT 0x04 /* Peripheral interrupt status */ |
| #define ASIC3_INTR_INT_CPS 0x08 /* Interrupt timer clock pre-scale */ |
| #define ASIC3_INTR_INT_TBS 0x0c /* Interrupt timer set */ |
| |
| #define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */ |
| #define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */ |
| #define ASIC3_INTMASK_MASK0 (1 << 2) |
| #define ASIC3_INTMASK_MASK1 (1 << 3) |
| #define ASIC3_INTMASK_MASK2 (1 << 4) |
| #define ASIC3_INTMASK_MASK3 (1 << 5) |
| #define ASIC3_INTMASK_MASK4 (1 << 6) |
| #define ASIC3_INTMASK_MASK5 (1 << 7) |
| |
| #define ASIC3_INTR_PERIPHERAL_A (1 << 0) |
| #define ASIC3_INTR_PERIPHERAL_B (1 << 1) |
| #define ASIC3_INTR_PERIPHERAL_C (1 << 2) |
| #define ASIC3_INTR_PERIPHERAL_D (1 << 3) |
| #define ASIC3_INTR_LED0 (1 << 4) |
| #define ASIC3_INTR_LED1 (1 << 5) |
| #define ASIC3_INTR_LED2 (1 << 6) |
| #define ASIC3_INTR_SPI (1 << 7) |
| #define ASIC3_INTR_SMBUS (1 << 8) |
| #define ASIC3_INTR_OWM (1 << 9) |
| |
| #define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */ |
| #define ASIC3_INTR_CPS_SET (1 << 4) /* Time base enable */ |
| |
| |
| /* Basic control of the SD ASIC */ |
| #define ASIC3_SDHWCTRL_BASE 0x0E00 |
| #define ASIC3_SDHWCTRL_SDCONF 0x00 |
| |
| #define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */ |
| #define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */ |
| #define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */ |
| #define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* SD card detection: 0:low */ |
| |
| /* SD card write protection: 0=high */ |
| #define ASIC3_SDHWCTRL_LEVWP (1 << 4) |
| #define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 0=disable */ |
| |
| /* SD card power supply ctrl 1=enable */ |
| #define ASIC3_SDHWCTRL_SDPWR (1 << 6) |
| |
| #define ASIC3_EXTCF_BASE 0x1100 |
| |
| #define ASIC3_EXTCF_SELECT 0x00 |
| #define ASIC3_EXTCF_RESET 0x04 |
| |
| #define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */ |
| #define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */ |
| #define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */ |
| #define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */ |
| #define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */ |
| #define ASIC3_EXTCF_OWM_RESET (1 << 6) /* ?? used by OWM and CF */ |
| #define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state */ |
| #define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state */ |
| #define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */ |
| #define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */ |
| #define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */ |
| #define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */ |
| #define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14) |
| #define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */ |
| |
| /********************************************* |
| * The Onewire interface (DS1WM) is handled |
| * by the ds1wm driver. |
| * |
| *********************************************/ |
| |
| #define ASIC3_OWM_BASE 0xC00 |
| |
| /***************************************************************************** |
| * The SD configuration registers are at a completely different location |
| * in memory. They are divided into three sets of registers: |
| * |
| * SD_CONFIG Core configuration register |
| * SD_CTRL Control registers for SD operations |
| * SDIO_CTRL Control registers for SDIO operations |
| * |
| *****************************************************************************/ |
| #define ASIC3_SD_CONFIG_BASE 0x0400 /* Assumes 32 bit addressing */ |
| #define ASIC3_SD_CTRL_BASE 0x1000 |
| #define ASIC3_SDIO_CTRL_BASE 0x1200 |
| |
| #define ASIC3_MAP_SIZE_32BIT 0x2000 |
| #define ASIC3_MAP_SIZE_16BIT 0x1000 |
| |
| #endif /* __ASIC3_H__ */ |