e1000e: Disable L1 ASPM power savings for 82573 mobile variants
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index b6401ab..45f5ee2 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -1343,7 +1343,6 @@
| FLAG_HAS_STATS_ICR_ICT
| FLAG_HAS_SMART_POWER_DOWN
| FLAG_HAS_AMT
- | FLAG_HAS_ASPM
| FLAG_HAS_ERT
| FLAG_HAS_SWSM_ON_LOAD,
.pba = 20,
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 473f78d..8b88c22 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -288,7 +288,6 @@
#define FLAG_HAS_CTRLEXT_ON_LOAD (1 << 5)
#define FLAG_HAS_SWSM_ON_LOAD (1 << 6)
#define FLAG_HAS_JUMBO_FRAMES (1 << 7)
-#define FLAG_HAS_ASPM (1 << 8)
#define FLAG_HAS_STATS_ICR_ICT (1 << 9)
#define FLAG_HAS_STATS_PTC_PRC (1 << 10)
#define FLAG_HAS_SMART_POWER_DOWN (1 << 11)
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 9cc5a6b..5450ef8 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -3509,6 +3509,33 @@
return 0;
}
+static void e1000e_disable_l1aspm(struct pci_dev *pdev)
+{
+ int pos;
+ u32 cap;
+ u16 val;
+
+ /*
+ * 82573 workaround - disable L1 ASPM on mobile chipsets
+ *
+ * L1 ASPM on various mobile (ich7) chipsets do not behave properly
+ * resulting in lost data or garbage information on the pci-e link
+ * level. This could result in (false) bad EEPROM checksum errors,
+ * long ping times (up to 2s) or even a system freeze/hang.
+ *
+ * Unfortunately this feature saves about 1W power consumption when
+ * active.
+ */
+ pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+ pci_read_config_dword(pdev, pos + PCI_EXP_LNKCAP, &cap);
+ pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &val);
+ if (val & 0x2) {
+ dev_warn(&pdev->dev, "Disabling L1 ASPM\n");
+ val &= ~0x2;
+ pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, val);
+ }
+}
+
#ifdef CONFIG_PM
static int e1000_resume(struct pci_dev *pdev)
{
@@ -3519,6 +3546,7 @@
pci_set_power_state(pdev, PCI_D0);
pci_restore_state(pdev);
+ e1000e_disable_l1aspm(pdev);
err = pci_enable_device(pdev);
if (err) {
dev_err(&pdev->dev,
@@ -3619,6 +3647,7 @@
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
+ e1000e_disable_l1aspm(pdev);
if (pci_enable_device(pdev)) {
dev_err(&pdev->dev,
"Cannot re-enable PCI device after reset.\n");
@@ -3720,6 +3749,7 @@
u16 eeprom_data = 0;
u16 eeprom_apme_mask = E1000_EEPROM_APME;
+ e1000e_disable_l1aspm(pdev);
err = pci_enable_device(pdev);
if (err)
return err;
diff --git a/drivers/net/e1000e/param.c b/drivers/net/e1000e/param.c
index 3327892..df266c3 100644
--- a/drivers/net/e1000e/param.c
+++ b/drivers/net/e1000e/param.c
@@ -262,13 +262,6 @@
.max = MAX_RXDELAY } }
};
- /* modify min and default if 82573 for slow ping w/a,
- * a value greater than 8 needs to be set for RDTR */
- if (adapter->flags & FLAG_HAS_ASPM) {
- opt.def = 32;
- opt.arg.r.min = 8;
- }
-
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,