| /* |
| * include/asm-arm/arch-at91/at91_spi.h |
| * |
| * Copyright (C) 2005 Ivan Kokshaysky |
| * Copyright (C) SAN People |
| * |
| * Serial Peripheral Interface (SPI) registers. |
| * Based on AT91RM9200 datasheet revision E. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| */ |
| |
| #ifndef AT91_SPI_H |
| #define AT91_SPI_H |
| |
| #define AT91_SPI_CR 0x00 /* Control Register */ |
| #define AT91_SPI_SPIEN (1 << 0) /* SPI Enable */ |
| #define AT91_SPI_SPIDIS (1 << 1) /* SPI Disable */ |
| #define AT91_SPI_SWRST (1 << 7) /* SPI Software Reset */ |
| #define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */ |
| |
| #define AT91_SPI_MR 0x04 /* Mode Register */ |
| #define AT91_SPI_MSTR (1 << 0) /* Master/Slave Mode */ |
| #define AT91_SPI_PS (1 << 1) /* Peripheral Select */ |
| #define AT91_SPI_PS_FIXED (0 << 1) |
| #define AT91_SPI_PS_VARIABLE (1 << 1) |
| #define AT91_SPI_PCSDEC (1 << 2) /* Chip Select Decode */ |
| #define AT91_SPI_DIV32 (1 << 3) /* Clock Selection [AT91RM9200 only] */ |
| #define AT91_SPI_MODFDIS (1 << 4) /* Mode Fault Detection */ |
| #define AT91_SPI_LLB (1 << 7) /* Local Loopback Enable */ |
| #define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ |
| #define AT91_SPI_DLYBCS (0xff << 24) /* Delay Between Chip Selects */ |
| |
| #define AT91_SPI_RDR 0x08 /* Receive Data Register */ |
| #define AT91_SPI_RD (0xffff << 0) /* Receive Data */ |
| #define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ |
| |
| #define AT91_SPI_TDR 0x0c /* Transmit Data Register */ |
| #define AT91_SPI_TD (0xffff << 0) /* Transmit Data */ |
| #define AT91_SPI_PCS (0xf << 16) /* Peripheral Chip Select */ |
| #define AT91_SPI_LASTXFER (1 << 24) /* Last Transfer [SAM9261 only] */ |
| |
| #define AT91_SPI_SR 0x10 /* Status Register */ |
| #define AT91_SPI_RDRF (1 << 0) /* Receive Data Register Full */ |
| #define AT91_SPI_TDRE (1 << 1) /* Transmit Data Register Full */ |
| #define AT91_SPI_MODF (1 << 2) /* Mode Fault Error */ |
| #define AT91_SPI_OVRES (1 << 3) /* Overrun Error Status */ |
| #define AT91_SPI_ENDRX (1 << 4) /* End of RX buffer */ |
| #define AT91_SPI_ENDTX (1 << 5) /* End of TX buffer */ |
| #define AT91_SPI_RXBUFF (1 << 6) /* RX Buffer Full */ |
| #define AT91_SPI_TXBUFE (1 << 7) /* TX Buffer Empty */ |
| #define AT91_SPI_NSSR (1 << 8) /* NSS Rising [SAM9261 only] */ |
| #define AT91_SPI_TXEMPTY (1 << 9) /* Transmission Register Empty [SAM9261 only] */ |
| #define AT91_SPI_SPIENS (1 << 16) /* SPI Enable Status */ |
| |
| #define AT91_SPI_IER 0x14 /* Interrupt Enable Register */ |
| #define AT91_SPI_IDR 0x18 /* Interrupt Disable Register */ |
| #define AT91_SPI_IMR 0x1c /* Interrupt Mask Register */ |
| |
| #define AT91_SPI_CSR(n) (0x30 + ((n) * 4)) /* Chip Select Registers 0-3 */ |
| #define AT91_SPI_CPOL (1 << 0) /* Clock Polarity */ |
| #define AT91_SPI_NCPHA (1 << 1) /* Clock Phase */ |
| #define AT91_SPI_CSAAT (1 << 3) /* Chip Select Active After Transfer [SAM9261 only] */ |
| #define AT91_SPI_BITS (0xf << 4) /* Bits Per Transfer */ |
| #define AT91_SPI_BITS_8 (0 << 4) |
| #define AT91_SPI_BITS_9 (1 << 4) |
| #define AT91_SPI_BITS_10 (2 << 4) |
| #define AT91_SPI_BITS_11 (3 << 4) |
| #define AT91_SPI_BITS_12 (4 << 4) |
| #define AT91_SPI_BITS_13 (5 << 4) |
| #define AT91_SPI_BITS_14 (6 << 4) |
| #define AT91_SPI_BITS_15 (7 << 4) |
| #define AT91_SPI_BITS_16 (8 << 4) |
| #define AT91_SPI_SCBR (0xff << 8) /* Serial Clock Baud Rate */ |
| #define AT91_SPI_DLYBS (0xff << 16) /* Delay before SPCK */ |
| #define AT91_SPI_DLYBCT (0xff << 24) /* Delay between Consecutive Transfers */ |
| |
| #endif |