x86: geode: MSR cleanup
This cleans up a few MSR-using drivers in the following manner:
- Ensures MSRs are all defined in asm/geode.h, rather than in misc
places
- Makes the naming consistent; cs553[56] ones begin with MSR_,
GX-specific ones start with MSR_GX_, and LX-specific ones start
with MSR_LX_. Also, make the names match the data sheet.
- Use MSR names rather than numbers in source code
- Document the fact that the LX's MSR_PADSEL has the wrong value
in the data sheet. That's, uh, good to note.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/video/geode/lxfb_ops.c b/drivers/video/geode/lxfb_ops.c
index 4fbc99b..a52c180 100644
--- a/drivers/video/geode/lxfb_ops.c
+++ b/drivers/video/geode/lxfb_ops.c
@@ -13,6 +13,7 @@
#include <linux/fb.h>
#include <linux/uaccess.h>
#include <linux/delay.h>
+#include <asm/geode.h>
#include "lxfb.h"
@@ -101,7 +102,7 @@
u32 dotpll_lo, dotpll_hi;
int i;
- rdmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
+ rdmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
if ((dotpll_lo & GLCP_DOTPLL_LOCK) && (dotpll_hi == pllval))
return;
@@ -110,7 +111,7 @@
dotpll_lo &= ~(GLCP_DOTPLL_BYPASS | GLCP_DOTPLL_HALFPIX);
dotpll_lo |= GLCP_DOTPLL_RESET;
- wrmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
+ wrmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
/* Wait 100us for the PLL to lock */
@@ -119,7 +120,7 @@
/* Now, loop for the lock bit */
for (i = 0; i < 1000; i++) {
- rdmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
+ rdmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
if (dotpll_lo & GLCP_DOTPLL_LOCK)
break;
}
@@ -127,7 +128,7 @@
/* Clear the reset bit */
dotpll_lo &= ~GLCP_DOTPLL_RESET;
- wrmsr(MSR_LX_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
+ wrmsr(MSR_GLCP_DOTPLL, dotpll_lo, dotpll_hi);
}
/* Set the clock based on the frequency specified by the current mode */
@@ -255,7 +256,7 @@
msrlo = DF_DEFAULT_TFT_PAD_SEL_LOW;
msrhi = DF_DEFAULT_TFT_PAD_SEL_HIGH;
- wrmsr(MSR_LX_DF_PADSEL, msrlo, msrhi);
+ wrmsr(MSR_LX_MSR_PADSEL, msrlo, msrhi);
}
if (par->output & OUTPUT_CRT) {
@@ -321,7 +322,7 @@
/* Set output mode */
- rdmsrl(MSR_LX_DF_GLCONFIG, msrval);
+ rdmsrl(MSR_LX_GLD_MSR_CONFIG, msrval);
msrval &= ~DF_CONFIG_OUTPUT_MASK;
if (par->output & OUTPUT_PANEL) {
@@ -335,7 +336,7 @@
msrval |= DF_OUTPUT_CRT;
}
- wrmsrl(MSR_LX_DF_GLCONFIG, msrval);
+ wrmsrl(MSR_LX_GLD_MSR_CONFIG, msrval);
/* Clear the various buffers */
/* FIXME: Adjust for panning here */
@@ -383,13 +384,13 @@
/* Set default watermark values */
- rdmsrl(MSR_LX_DC_SPARE, msrval);
+ rdmsrl(MSR_LX_SPARE_MSR, msrval);
msrval &= ~(DC_SPARE_DISABLE_CFIFO_HGO | DC_SPARE_VFIFO_ARB_SELECT |
DC_SPARE_LOAD_WM_LPEN_MASK | DC_SPARE_WM_LPEN_OVRD |
DC_SPARE_DISABLE_INIT_VID_PRI | DC_SPARE_DISABLE_VFIFO_WM);
msrval |= DC_SPARE_DISABLE_VFIFO_WM | DC_SPARE_DISABLE_INIT_VID_PRI;
- wrmsrl(MSR_LX_DC_SPARE, msrval);
+ wrmsrl(MSR_LX_SPARE_MSR, msrval);
gcfg = DC_GCFG_DFLE; /* Display fifo enable */
gcfg |= 0xB600; /* Set default priority */