powerpc/85xx: Add p2040 RDB board support
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/arch/powerpc/boot/dts/p2040rdb.dts b/arch/powerpc/boot/dts/p2040rdb.dts
new file mode 100644
index 0000000..7d84e39
--- /dev/null
+++ b/arch/powerpc/boot/dts/p2040rdb.dts
@@ -0,0 +1,166 @@
+/*
+ * P2040RDB Device Tree Source
+ *
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "p2040si.dtsi"
+
+/ {
+ model = "fsl,P2040RDB";
+ compatible = "fsl,P2040RDB";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ memory {
+ device_type = "memory";
+ };
+
+ soc: soc@ffe000000 {
+ spi@110000 {
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl12801";
+ reg = <0>;
+ spi-max-frequency = <40000000>; /* input clock */
+ partition@u-boot {
+ label = "u-boot";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition@kernel {
+ label = "kernel";
+ reg = <0x00100000 0x00500000>;
+ read-only;
+ };
+ partition@dtb {
+ label = "dtb";
+ reg = <0x00600000 0x00100000>;
+ read-only;
+ };
+ partition@fs {
+ label = "file system";
+ reg = <0x00700000 0x00900000>;
+ };
+ };
+ };
+
+ i2c@118000 {
+ lm75b@48 {
+ compatible = "nxp,lm75a";
+ reg = <0x48>;
+ };
+ eeprom@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+ rtc@68 {
+ compatible = "pericom,pt7c4338";
+ reg = <0x68>;
+ };
+ };
+
+ i2c@118100 {
+ eeprom@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+ };
+
+ usb0: usb@210000 {
+ phy_type = "utmi";
+ };
+
+ usb1: usb@211000 {
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+ };
+
+ localbus@ffe124000 {
+ reg = <0xf 0xfe124000 0 0x1000>;
+ ranges = <0 0 0xf 0xe8000000 0x08000000>;
+
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x08000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ };
+ };
+
+ pci0: pcie@ffe200000 {
+ reg = <0xf 0xfe200000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x00000000 0x0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8000000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci1: pcie@ffe201000 {
+ reg = <0xf 0xfe201000 0 0x1000>;
+ ranges = <0x02000000 0x0 0xe0000000 0xc 0x20000000 0x0 0x20000000
+ 0x01000000 0x0 0x00000000 0xf 0xf8010000 0x0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+
+ pci2: pcie@ffe202000 {
+ reg = <0xf 0xfe202000 0 0x1000>;
+ ranges = <0x02000000 0 0xe0000000 0xc 0x40000000 0 0x20000000
+ 0x01000000 0 0x00000000 0xf 0xf8020000 0 0x00010000>;
+ pcie@0 {
+ ranges = <0x02000000 0 0xe0000000
+ 0x02000000 0 0xe0000000
+ 0 0x20000000
+
+ 0x01000000 0 0x00000000
+ 0x01000000 0 0x00000000
+ 0 0x00010000>;
+ };
+ };
+};