ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
The following commits change gpio-omap to use dynamic
IRQ allocation:
25db711 gpio/omap: Fix IRQ handling for SPARSE_IRQ
384ebe1 gpio/omap: Add DT support to GPIO driver
With dynamic allocation of IRQ the usage of OMAP_GPIO_IRQ
is no longer valid. We must be using gpio_to_irq() instead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index e2d7ae4..a0c1a1c 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -128,8 +128,6 @@
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = OMAP_GPIO_IRQ(0),
- .end = OMAP_GPIO_IRQ(0),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
@@ -146,8 +144,6 @@
static struct resource osk5912_cf_resources[] = {
[0] = {
- .start = OMAP_GPIO_IRQ(62),
- .end = OMAP_GPIO_IRQ(62),
.flags = IORESOURCE_IRQ,
},
};
@@ -239,7 +235,6 @@
static struct i2c_board_info __initdata osk_i2c_board_info[] = {
{
I2C_BOARD_INFO("tps65010", 0x48),
- .irq = OMAP_GPIO_IRQ(OMAP_MPUIO(1)),
.platform_data = &tps_board,
},
@@ -413,7 +408,6 @@
/* MicroWire (bus 2) CS0 has an ads7846e */
.modalias = "ads7846",
.platform_data = &mistral_ts_info,
- .irq = OMAP_GPIO_IRQ(4),
.max_speed_hz = 120000 /* max sample rate at 3V */
* 26 /* command + data + overhead */,
.bus_num = 2,
@@ -476,6 +470,7 @@
gpio_direction_input(4);
irq_set_irq_type(gpio_to_irq(4), IRQ_TYPE_EDGE_FALLING);
+ mistral_boardinfo[0].irq = gpio_to_irq(4);
spi_register_board_info(mistral_boardinfo,
ARRAY_SIZE(mistral_boardinfo));
@@ -547,6 +542,10 @@
osk_flash_resource.end = osk_flash_resource.start = omap_cs3_phys();
osk_flash_resource.end += SZ_32M - 1;
+ osk5912_smc91x_resources[1].start = gpio_to_irq(0);
+ osk5912_smc91x_resources[1].end = gpio_to_irq(0);
+ osk5912_cf_resources[0].start = gpio_to_irq(62);
+ osk5912_cf_resources[0].end = gpio_to_irq(62);
platform_add_devices(osk5912_devices, ARRAY_SIZE(osk5912_devices));
omap_board_config = osk_config;
omap_board_config_size = ARRAY_SIZE(osk_config);
@@ -563,6 +562,7 @@
gpio_direction_input(OMAP_MPUIO(1));
omap_serial_init();
+ osk_i2c_board_info[0].irq = gpio_to_irq(OMAP_MPUIO(1));
omap_register_i2c_bus(1, 400, osk_i2c_board_info,
ARRAY_SIZE(osk_i2c_board_info));
osk_mistral_init();