e1000: Add support for the CE4100 reference platform

This patch adds support for the gigabit phys present on the CE4100 reference
platforms.

Signed-off-by:  Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index 77d08e6..aed223b 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -130,10 +130,15 @@
 		if (hw->mac_type == e1000_82541 ||
 		    hw->mac_type == e1000_82541_rev_2 ||
 		    hw->mac_type == e1000_82547 ||
-		    hw->mac_type == e1000_82547_rev_2) {
+		    hw->mac_type == e1000_82547_rev_2)
 			hw->phy_type = e1000_phy_igp;
-			break;
-		}
+		break;
+	case RTL8211B_PHY_ID:
+		hw->phy_type = e1000_phy_8211;
+		break;
+	case RTL8201N_PHY_ID:
+		hw->phy_type = e1000_phy_8201;
+		break;
 	default:
 		/* Should never have loaded on this device */
 		hw->phy_type = e1000_phy_undefined;
@@ -318,6 +323,9 @@
 	case E1000_DEV_ID_82547GI:
 		hw->mac_type = e1000_82547_rev_2;
 		break;
+	case E1000_DEV_ID_INTEL_CE4100_GBE:
+		hw->mac_type = e1000_ce4100;
+		break;
 	default:
 		/* Should never have loaded on this device */
 		return -E1000_ERR_MAC_TYPE;
@@ -372,6 +380,9 @@
 		case e1000_82542_rev2_1:
 			hw->media_type = e1000_media_type_fiber;
 			break;
+		case e1000_ce4100:
+			hw->media_type = e1000_media_type_copper;
+			break;
 		default:
 			status = er32(STATUS);
 			if (status & E1000_STATUS_TBIMODE) {
@@ -460,6 +471,7 @@
 		/* Reset is performed on a shadow of the control register */
 		ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST));
 		break;
+	case e1000_ce4100:
 	default:
 		ew32(CTRL, (ctrl | E1000_CTRL_RST));
 		break;
@@ -952,6 +964,67 @@
 }
 
 /**
+ * e1000_copper_link_rtl_setup - Copper link setup for e1000_phy_rtl series.
+ * @hw: Struct containing variables accessed by shared code
+ *
+ * Commits changes to PHY configuration by calling e1000_phy_reset().
+ */
+static s32 e1000_copper_link_rtl_setup(struct e1000_hw *hw)
+{
+	s32 ret_val;
+
+	/* SW reset the PHY so all changes take effect */
+	ret_val = e1000_phy_reset(hw);
+	if (ret_val) {
+		e_dbg("Error Resetting the PHY\n");
+		return ret_val;
+	}
+
+	return E1000_SUCCESS;
+}
+
+static s32 gbe_dhg_phy_setup(struct e1000_hw *hw)
+{
+	s32 ret_val;
+	u32 ctrl_aux;
+
+	switch (hw->phy_type) {
+	case e1000_phy_8211:
+		ret_val = e1000_copper_link_rtl_setup(hw);
+		if (ret_val) {
+			e_dbg("e1000_copper_link_rtl_setup failed!\n");
+			return ret_val;
+		}
+		break;
+	case e1000_phy_8201:
+		/* Set RMII mode */
+		ctrl_aux = er32(CTL_AUX);
+		ctrl_aux |= E1000_CTL_AUX_RMII;
+		ew32(CTL_AUX, ctrl_aux);
+		E1000_WRITE_FLUSH();
+
+		/* Disable the J/K bits required for receive */
+		ctrl_aux = er32(CTL_AUX);
+		ctrl_aux |= 0x4;
+		ctrl_aux &= ~0x2;
+		ew32(CTL_AUX, ctrl_aux);
+		E1000_WRITE_FLUSH();
+		ret_val = e1000_copper_link_rtl_setup(hw);
+
+		if (ret_val) {
+			e_dbg("e1000_copper_link_rtl_setup failed!\n");
+			return ret_val;
+		}
+		break;
+	default:
+		e_dbg("Error Resetting the PHY\n");
+		return E1000_ERR_PHY_TYPE;
+	}
+
+	return E1000_SUCCESS;
+}
+
+/**
  * e1000_copper_link_preconfig - early configuration for copper
  * @hw: Struct containing variables accessed by shared code
  *
@@ -1286,6 +1359,10 @@
 	if (hw->autoneg_advertised == 0)
 		hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;
 
+	/* IFE/RTL8201N PHY only supports 10/100 */
+	if (hw->phy_type == e1000_phy_8201)
+		hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;
+
 	e_dbg("Reconfiguring auto-neg advertisement params\n");
 	ret_val = e1000_phy_setup_autoneg(hw);
 	if (ret_val) {
@@ -1341,7 +1418,7 @@
 	s32 ret_val;
 	e_dbg("e1000_copper_link_postconfig");
 
-	if (hw->mac_type >= e1000_82544) {
+	if ((hw->mac_type >= e1000_82544) && (hw->mac_type != e1000_ce4100)) {
 		e1000_config_collision_dist(hw);
 	} else {
 		ret_val = e1000_config_mac_to_phy(hw);
@@ -1395,6 +1472,12 @@
 		ret_val = e1000_copper_link_mgp_setup(hw);
 		if (ret_val)
 			return ret_val;
+	} else {
+		ret_val = gbe_dhg_phy_setup(hw);
+		if (ret_val) {
+			e_dbg("gbe_dhg_phy_setup failed!\n");
+			return ret_val;
+		}
 	}
 
 	if (hw->autoneg) {
@@ -1461,10 +1544,11 @@
 		return ret_val;
 
 	/* Read the MII 1000Base-T Control Register (Address 9). */
-	ret_val =
-	    e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
+	ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg);
 	if (ret_val)
 		return ret_val;
+	else if (hw->phy_type == e1000_phy_8201)
+		mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;
 
 	/* Need to parse both autoneg_advertised and fc and set up
 	 * the appropriate PHY registers.  First we will parse for
@@ -1577,9 +1661,14 @@
 
 	e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
 
-	ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
-	if (ret_val)
-		return ret_val;
+	if (hw->phy_type == e1000_phy_8201) {
+		mii_1000t_ctrl_reg = 0;
+	} else {
+		ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
+		                              mii_1000t_ctrl_reg);
+		if (ret_val)
+			return ret_val;
+	}
 
 	return E1000_SUCCESS;
 }
@@ -1860,7 +1949,7 @@
 
 	/* 82544 or newer MAC, Auto Speed Detection takes care of
 	 * MAC speed/duplex configuration.*/
-	if (hw->mac_type >= e1000_82544)
+	if ((hw->mac_type >= e1000_82544) && (hw->mac_type != e1000_ce4100))
 		return E1000_SUCCESS;
 
 	/* Read the Device Control Register and set the bits to Force Speed
@@ -1870,27 +1959,49 @@
 	ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
 	ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS);
 
-	/* Set up duplex in the Device Control and Transmit Control
-	 * registers depending on negotiated values.
-	 */
-	ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
-	if (ret_val)
-		return ret_val;
+	switch (hw->phy_type) {
+	case e1000_phy_8201:
+		ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
+		if (ret_val)
+			return ret_val;
 
-	if (phy_data & M88E1000_PSSR_DPLX)
-		ctrl |= E1000_CTRL_FD;
-	else
-		ctrl &= ~E1000_CTRL_FD;
+		if (phy_data & RTL_PHY_CTRL_FD)
+			ctrl |= E1000_CTRL_FD;
+		else
+			ctrl &= ~E1000_CTRL_FD;
 
-	e1000_config_collision_dist(hw);
+		if (phy_data & RTL_PHY_CTRL_SPD_100)
+			ctrl |= E1000_CTRL_SPD_100;
+		else
+			ctrl |= E1000_CTRL_SPD_10;
 
-	/* Set up speed in the Device Control register depending on
-	 * negotiated values.
-	 */
-	if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
-		ctrl |= E1000_CTRL_SPD_1000;
-	else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
-		ctrl |= E1000_CTRL_SPD_100;
+		e1000_config_collision_dist(hw);
+		break;
+	default:
+		/* Set up duplex in the Device Control and Transmit Control
+		 * registers depending on negotiated values.
+		 */
+		ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
+		                             &phy_data);
+		if (ret_val)
+			return ret_val;
+
+		if (phy_data & M88E1000_PSSR_DPLX)
+			ctrl |= E1000_CTRL_FD;
+		else
+			ctrl &= ~E1000_CTRL_FD;
+
+		e1000_config_collision_dist(hw);
+
+		/* Set up speed in the Device Control register depending on
+		 * negotiated values.
+		 */
+		if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
+			ctrl |= E1000_CTRL_SPD_1000;
+		else if ((phy_data & M88E1000_PSSR_SPEED) ==
+		         M88E1000_PSSR_100MBS)
+			ctrl |= E1000_CTRL_SPD_100;
+	}
 
 	/* Write the configured values back to the Device Control Reg. */
 	ew32(CTRL, ctrl);
@@ -2401,7 +2512,8 @@
 		 * speed/duplex on the MAC to the current PHY speed/duplex
 		 * settings.
 		 */
-		if (hw->mac_type >= e1000_82544)
+		if ((hw->mac_type >= e1000_82544) &&
+		    (hw->mac_type != e1000_ce4100))
 			e1000_config_collision_dist(hw);
 		else {
 			ret_val = e1000_config_mac_to_phy(hw);
@@ -2738,7 +2850,7 @@
 {
 	u32 i;
 	u32 mdic = 0;
-	const u32 phy_addr = 1;
+	const u32 phy_addr = (hw->mac_type == e1000_ce4100) ? hw->phy_addr : 1;
 
 	e_dbg("e1000_read_phy_reg_ex");
 
@@ -2752,28 +2864,61 @@
 		 * Control register.  The MAC will take care of interfacing with the
 		 * PHY to retrieve the desired data.
 		 */
-		mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
-			(phy_addr << E1000_MDIC_PHY_SHIFT) |
-			(E1000_MDIC_OP_READ));
+		if (hw->mac_type == e1000_ce4100) {
+			mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+				(phy_addr << E1000_MDIC_PHY_SHIFT) |
+				(INTEL_CE_GBE_MDIC_OP_READ) |
+				(INTEL_CE_GBE_MDIC_GO));
 
-		ew32(MDIC, mdic);
+			writel(mdic, E1000_MDIO_CMD);
 
-		/* Poll the ready bit to see if the MDI read completed */
-		for (i = 0; i < 64; i++) {
-			udelay(50);
-			mdic = er32(MDIC);
-			if (mdic & E1000_MDIC_READY)
-				break;
+			/* Poll the ready bit to see if the MDI read
+			 * completed
+			 */
+			for (i = 0; i < 64; i++) {
+				udelay(50);
+				mdic = readl(E1000_MDIO_CMD);
+				if (!(mdic & INTEL_CE_GBE_MDIC_GO))
+					break;
+			}
+
+			if (mdic & INTEL_CE_GBE_MDIC_GO) {
+				e_dbg("MDI Read did not complete\n");
+				return -E1000_ERR_PHY;
+			}
+
+			mdic = readl(E1000_MDIO_STS);
+			if (mdic & INTEL_CE_GBE_MDIC_READ_ERROR) {
+				e_dbg("MDI Read Error\n");
+				return -E1000_ERR_PHY;
+			}
+			*phy_data = (u16) mdic;
+		} else {
+			mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
+				(phy_addr << E1000_MDIC_PHY_SHIFT) |
+				(E1000_MDIC_OP_READ));
+
+			ew32(MDIC, mdic);
+
+			/* Poll the ready bit to see if the MDI read
+			 * completed
+			 */
+			for (i = 0; i < 64; i++) {
+				udelay(50);
+				mdic = er32(MDIC);
+				if (mdic & E1000_MDIC_READY)
+					break;
+			}
+			if (!(mdic & E1000_MDIC_READY)) {
+				e_dbg("MDI Read did not complete\n");
+				return -E1000_ERR_PHY;
+			}
+			if (mdic & E1000_MDIC_ERROR) {
+				e_dbg("MDI Error\n");
+				return -E1000_ERR_PHY;
+			}
+			*phy_data = (u16) mdic;
 		}
-		if (!(mdic & E1000_MDIC_READY)) {
-			e_dbg("MDI Read did not complete\n");
-			return -E1000_ERR_PHY;
-		}
-		if (mdic & E1000_MDIC_ERROR) {
-			e_dbg("MDI Error\n");
-			return -E1000_ERR_PHY;
-		}
-		*phy_data = (u16) mdic;
 	} else {
 		/* We must first send a preamble through the MDIO pin to signal the
 		 * beginning of an MII instruction.  This is done by sending 32
@@ -2840,7 +2985,7 @@
 {
 	u32 i;
 	u32 mdic = 0;
-	const u32 phy_addr = 1;
+	const u32 phy_addr = (hw->mac_type == e1000_ce4100) ? hw->phy_addr : 1;
 
 	e_dbg("e1000_write_phy_reg_ex");
 
@@ -2850,27 +2995,54 @@
 	}
 
 	if (hw->mac_type > e1000_82543) {
-		/* Set up Op-code, Phy Address, register address, and data intended
-		 * for the PHY register in the MDI Control register.  The MAC will take
-		 * care of interfacing with the PHY to send the desired data.
+		/* Set up Op-code, Phy Address, register address, and data
+		 * intended for the PHY register in the MDI Control register.
+		 * The MAC will take care of interfacing with the PHY to send
+		 * the desired data.
 		 */
-		mdic = (((u32) phy_data) |
-			(reg_addr << E1000_MDIC_REG_SHIFT) |
-			(phy_addr << E1000_MDIC_PHY_SHIFT) |
-			(E1000_MDIC_OP_WRITE));
+		if (hw->mac_type == e1000_ce4100) {
+			mdic = (((u32) phy_data) |
+				(reg_addr << E1000_MDIC_REG_SHIFT) |
+				(phy_addr << E1000_MDIC_PHY_SHIFT) |
+				(INTEL_CE_GBE_MDIC_OP_WRITE) |
+				(INTEL_CE_GBE_MDIC_GO));
 
-		ew32(MDIC, mdic);
+			writel(mdic, E1000_MDIO_CMD);
 
-		/* Poll the ready bit to see if the MDI read completed */
-		for (i = 0; i < 641; i++) {
-			udelay(5);
-			mdic = er32(MDIC);
-			if (mdic & E1000_MDIC_READY)
-				break;
-		}
-		if (!(mdic & E1000_MDIC_READY)) {
-			e_dbg("MDI Write did not complete\n");
-			return -E1000_ERR_PHY;
+			/* Poll the ready bit to see if the MDI read
+			 * completed
+			 */
+			for (i = 0; i < 640; i++) {
+				udelay(5);
+				mdic = readl(E1000_MDIO_CMD);
+				if (!(mdic & INTEL_CE_GBE_MDIC_GO))
+					break;
+			}
+			if (mdic & INTEL_CE_GBE_MDIC_GO) {
+				e_dbg("MDI Write did not complete\n");
+				return -E1000_ERR_PHY;
+			}
+		} else {
+			mdic = (((u32) phy_data) |
+				(reg_addr << E1000_MDIC_REG_SHIFT) |
+				(phy_addr << E1000_MDIC_PHY_SHIFT) |
+				(E1000_MDIC_OP_WRITE));
+
+			ew32(MDIC, mdic);
+
+			/* Poll the ready bit to see if the MDI read
+			 * completed
+			 */
+			for (i = 0; i < 641; i++) {
+				udelay(5);
+				mdic = er32(MDIC);
+				if (mdic & E1000_MDIC_READY)
+					break;
+			}
+			if (!(mdic & E1000_MDIC_READY)) {
+				e_dbg("MDI Write did not complete\n");
+				return -E1000_ERR_PHY;
+			}
 		}
 	} else {
 		/* We'll need to use the SW defined pins to shift the write command
@@ -3048,6 +3220,11 @@
 		if (hw->phy_id == M88E1011_I_PHY_ID)
 			match = true;
 		break;
+	case e1000_ce4100:
+		if ((hw->phy_id == RTL8211B_PHY_ID) ||
+		    (hw->phy_id == RTL8201N_PHY_ID))
+			match = true;
+		break;
 	case e1000_82541:
 	case e1000_82541_rev_2:
 	case e1000_82547:
@@ -3291,6 +3468,9 @@
 
 	if (hw->phy_type == e1000_phy_igp)
 		return e1000_phy_igp_get_info(hw, phy_info);
+	else if ((hw->phy_type == e1000_phy_8211) ||
+	         (hw->phy_type == e1000_phy_8201))
+		return E1000_SUCCESS;
 	else
 		return e1000_phy_m88_get_info(hw, phy_info);
 }
@@ -3742,6 +3922,12 @@
 
 	e_dbg("e1000_read_eeprom");
 
+	if (hw->mac_type == e1000_ce4100) {
+		GBE_CONFIG_FLASH_READ(GBE_CONFIG_BASE_VIRT, offset, words,
+		                      data);
+		return E1000_SUCCESS;
+	}
+
 	/* If eeprom is not yet detected, do so now */
 	if (eeprom->word_size == 0)
 		e1000_init_eeprom_params(hw);
@@ -3904,6 +4090,12 @@
 
 	e_dbg("e1000_write_eeprom");
 
+	if (hw->mac_type == e1000_ce4100) {
+		GBE_CONFIG_FLASH_WRITE(GBE_CONFIG_BASE_VIRT, offset, words,
+		                       data);
+		return E1000_SUCCESS;
+	}
+
 	/* If eeprom is not yet detected, do so now */
 	if (eeprom->word_size == 0)
 		e1000_init_eeprom_params(hw);