Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Signed-off-by: Bryan Wu <cooloney@kernel.org>
diff --git a/arch/blackfin/mach-bf533/head.S b/arch/blackfin/mach-bf533/head.S
index d59db86..01b2b7e 100644
--- a/arch/blackfin/mach-bf533/head.S
+++ b/arch/blackfin/mach-bf533/head.S
@@ -31,8 +31,8 @@
#include <linux/init.h>
#include <asm/blackfin.h>
#ifdef CONFIG_BFIN_KERNEL_CLOCK
-#include <asm/mach-common/clocks.h>
-#include <asm/mach/mem_init.h>
+#include <asm/clocks.h>
+#include <mach/mem_init.h>
#endif
.section .l1.text
diff --git a/arch/blackfin/mach-bf533/include/mach/anomaly.h b/arch/blackfin/mach-bf533/include/mach/anomaly.h
new file mode 100644
index 0000000..8f7ea11
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/anomaly.h
@@ -0,0 +1,272 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+/* This file shoule be up to date with:
+ * - Revision C, 02/08/2008; ADSP-BF531/BF532/BF533 Blackfin Processor Anomaly List
+ */
+
+#ifndef _MACH_ANOMALY_H_
+#define _MACH_ANOMALY_H_
+
+/* We do not support 0.1 or 0.2 silicon - sorry */
+#if __SILICON_REVISION__ < 3
+# error will not work on BF533 silicon version 0.0, 0.1, or 0.2
+#endif
+
+#if defined(__ADSPBF531__)
+# define ANOMALY_BF531 1
+#else
+# define ANOMALY_BF531 0
+#endif
+#if defined(__ADSPBF532__)
+# define ANOMALY_BF532 1
+#else
+# define ANOMALY_BF532 0
+#endif
+#if defined(__ADSPBF533__)
+# define ANOMALY_BF533 1
+#else
+# define ANOMALY_BF533 0
+#endif
+
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
+#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
+/* Watchpoint Status Register (WPSTAT) Bits Are Set on Every Corresponding Match */
+#define ANOMALY_05000105 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Instruction DMA Can Cause Data Cache Fills to Fail (Boot Implications) */
+#define ANOMALY_05000158 (__SILICON_REVISION__ < 5)
+/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */
+#define ANOMALY_05000166 (1)
+/* Turning Serial Ports on with External Frame Syncs */
+#define ANOMALY_05000167 (1)
+/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */
+#define ANOMALY_05000179 (__SILICON_REVISION__ < 5)
+/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
+#define ANOMALY_05000180 (1)
+/* Timer Pin Limitations for PPI TX Modes with External Frame Syncs */
+#define ANOMALY_05000183 (__SILICON_REVISION__ < 4)
+/* False Protection Exceptions */
+#define ANOMALY_05000189 (__SILICON_REVISION__ < 4)
+/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
+#define ANOMALY_05000193 (__SILICON_REVISION__ < 4)
+/* Restarting SPORT in Specific Modes May Cause Data Corruption */
+#define ANOMALY_05000194 (__SILICON_REVISION__ < 4)
+/* Failing MMR Accesses When Stalled by Preceding Memory Read */
+#define ANOMALY_05000198 (__SILICON_REVISION__ < 5)
+/* Current DMA Address Shows Wrong Value During Carry Fix */
+#define ANOMALY_05000199 (__SILICON_REVISION__ < 4)
+/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */
+#define ANOMALY_05000200 (__SILICON_REVISION__ < 5)
+/* Receive Frame Sync Not Ignored During Active Frames in SPORT Multi-Channel Mode */
+#define ANOMALY_05000201 (__SILICON_REVISION__ < 4)
+/* Possible Infinite Stall with Specific Dual-DAG Situation */
+#define ANOMALY_05000202 (__SILICON_REVISION__ < 5)
+/* Specific Sequence That Can Cause DMA Error or DMA Stopping */
+#define ANOMALY_05000203 (__SILICON_REVISION__ < 4)
+/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */
+#define ANOMALY_05000204 (__SILICON_REVISION__ < 4 && ANOMALY_BF533)
+/* Recovery from "Brown-Out" Condition */
+#define ANOMALY_05000207 (__SILICON_REVISION__ < 4)
+/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */
+#define ANOMALY_05000208 (1)
+/* Speed Path in Computational Unit Affects Certain Instructions */
+#define ANOMALY_05000209 (__SILICON_REVISION__ < 4)
+/* UART TX Interrupt Masked Erroneously */
+#define ANOMALY_05000215 (__SILICON_REVISION__ < 5)
+/* NMI Event at Boot Time Results in Unpredictable State */
+#define ANOMALY_05000219 (1)
+/* Incorrect Pulse-Width of UART Start Bit */
+#define ANOMALY_05000225 (__SILICON_REVISION__ < 5)
+/* Scratchpad Memory Bank Reads May Return Incorrect Data */
+#define ANOMALY_05000227 (__SILICON_REVISION__ < 5)
+/* SPI Slave Boot Mode Modifies Registers from Reset Value */
+#define ANOMALY_05000229 (1)
+/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */
+#define ANOMALY_05000230 (__SILICON_REVISION__ < 5)
+/* UART STB Bit Incorrectly Affects Receiver Setting */
+#define ANOMALY_05000231 (__SILICON_REVISION__ < 5)
+/* PPI_FS3 Is Not Driven in 2 or 3 Internal Frame Sync Transmit Modes */
+#define ANOMALY_05000233 (__SILICON_REVISION__ < 4)
+/* Incorrect Revision Number in DSPID Register */
+#define ANOMALY_05000234 (__SILICON_REVISION__ == 4)
+/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */
+#define ANOMALY_05000242 (__SILICON_REVISION__ < 4)
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 5)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Data CPLBs Should Prevent Spurious Hardware Errors */
+#define ANOMALY_05000246 (__SILICON_REVISION__ < 5)
+/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ == 4)
+/* Maximum External Clock Speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 5)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 4)
+/* Entering Hibernate State with RTC Seconds Interrupt Not Functional */
+#define ANOMALY_05000255 (__SILICON_REVISION__ < 5)
+/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 5)
+/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */
+#define ANOMALY_05000258 (__SILICON_REVISION__ < 5)
+/* ICPLB_STATUS MMR Register May Be Corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ < 5)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 5)
+/* Stores To Data Cache May Be Lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 5)
+/* Hardware Loop Corrupted When Taking an ICPLB Exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ < 5)
+/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 5)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */
+#define ANOMALY_05000269 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
+#define ANOMALY_05000270 (__SILICON_REVISION__ < 5)
+/* Spontaneous Reset of Internal Voltage Regulator */
+#define ANOMALY_05000271 (__SILICON_REVISION__ < 4)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* Writes to Synchronous SDRAM Memory May Be Lost */
+#define ANOMALY_05000273 (1)
+/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
+#define ANOMALY_05000276 (1)
+/* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */
+#define ANOMALY_05000277 (1)
+/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
+#define ANOMALY_05000278 (1)
+/* False Hardware Error Exception When ISR Context Is Not Restored */
+#define ANOMALY_05000281 (1)
+/* Memory DMA Corruption with 32-Bit Data and Traffic Control */
+#define ANOMALY_05000282 (1)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (1)
+/* SPORTs May Receive Bad Data If FIFOs Fill Up */
+#define ANOMALY_05000288 (1)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
+#define ANOMALY_05000302 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */
+#define ANOMALY_05000306 (__SILICON_REVISION__ < 5)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Erroneous Flag (GPIO) Pin Operations under Specific Sequences */
+#define ANOMALY_05000311 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (1)
+/* Internal Voltage Regulator Values of 1.05V, 1.10V and 1.15V Not Allowed for LQFP Packages */
+#define ANOMALY_05000319 (ANOMALY_BF531 || ANOMALY_BF532)
+/* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */
+#define ANOMALY_05000357 (1)
+/* UART Break Signal Issues */
+#define ANOMALY_05000363 (__SILICON_REVISION__ < 5)
+/* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */
+#define ANOMALY_05000366 (1)
+/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */
+#define ANOMALY_05000371 (1)
+/* PPI Does Not Start Properly In Specific Mode */
+#define ANOMALY_05000400 (__SILICON_REVISION__ >= 5)
+/* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */
+#define ANOMALY_05000402 (__SILICON_REVISION__ >= 5)
+/* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */
+#define ANOMALY_05000403 (1)
+
+
+/* These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
+
+/* Watchpoints (Hardware Breakpoints) are not supported */
+#define ANOMALY_05000067 (__SILICON_REVISION__ < 3)
+/* Reserved bits in SYSCFG register not set at power on */
+#define ANOMALY_05000109 (__SILICON_REVISION__ < 3)
+/* Trace Buffers may record discontinuities into emulation mode and/or exception, NMI, reset handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* DTEST_COMMAND initiated memory access may be incorrect if data cache or DMA is active */
+#define ANOMALY_05000123 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000124 (__SILICON_REVISION__ < 3)
+/* Erroneous exception when enabling cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* SPI clock polarity and phase bits incorrect during booting */
+#define ANOMALY_05000126 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL is not set on Reset */
+#define ANOMALY_05000137 (__SILICON_REVISION__ < 3)
+/* SPI boot will not complete if there is a zero fill block in the loader file */
+#define ANOMALY_05000138 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* An Infinite Stall occurs with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000143 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* The source MDMA descriptor may stop with a DMA Error */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* When booting from a 16-bit asynchronous memory device, the upper 8-bits of each word must be 0x00 */
+#define ANOMALY_05000148 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal is active in Multi-channel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Timer1 can not be used for PWMOUT mode when a certain PPI mode is in use */
+#define ANOMALY_05000155 (__SILICON_REVISION__ < 3)
+/* A killed 32-bit System MMR write will lead to the next system MMR access thinking it should be 32-bit. */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* SPORT transmit data is not gated by external frame sync in certain conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000168 (__SILICON_REVISION__ < 3)
+/* DATA CPLB page miss can result in lost write-through cache data writes */
+#define ANOMALY_05000169 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* Cache Fill Buffer Data lost */
+#define ANOMALY_05000174 (__SILICON_REVISION__ < 3)
+/* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000175 (__SILICON_REVISION__ < 3)
+/* Multiplication of (-1) by (-1) followed by an accumulator saturation */
+#define ANOMALY_05000176 (__SILICON_REVISION__ < 3)
+/* Disabling the PPI resets the PPI configuration registers */
+#define ANOMALY_05000181 (__SILICON_REVISION__ < 3)
+/* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000185 (__SILICON_REVISION__ < 3)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* In PPI Transmit Modes with External Frame Syncs POLC */
+#define ANOMALY_05000192 (__SILICON_REVISION__ < 3)
+/* Internal Voltage Regulator may not start up */
+#define ANOMALY_05000206 (__SILICON_REVISION__ < 3)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000323 (0)
+
+#endif
diff --git a/arch/blackfin/mach-bf533/include/mach/bf533.h b/arch/blackfin/mach-bf533/include/mach/bf533.h
new file mode 100644
index 0000000..12a4169
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/bf533.h
@@ -0,0 +1,161 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/bf533.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description: SYSTEM MMR REGISTER AND MEMORY MAP FOR ADSP-BF561
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef __MACH_BF533_H__
+#define __MACH_BF533_H__
+
+#define SUPPORTED_REVID 2
+
+#define OFFSET_(x) ((x) & 0x0000FFFF)
+
+/*some misc defines*/
+#define IMASK_IVG15 0x8000
+#define IMASK_IVG14 0x4000
+#define IMASK_IVG13 0x2000
+#define IMASK_IVG12 0x1000
+
+#define IMASK_IVG11 0x0800
+#define IMASK_IVG10 0x0400
+#define IMASK_IVG9 0x0200
+#define IMASK_IVG8 0x0100
+
+#define IMASK_IVG7 0x0080
+#define IMASK_IVGTMR 0x0040
+#define IMASK_IVGHW 0x0020
+
+/***************************/
+
+
+#define BFIN_DSUBBANKS 4
+#define BFIN_DWAYS 2
+#define BFIN_DLINES 64
+#define BFIN_ISUBBANKS 4
+#define BFIN_IWAYS 4
+#define BFIN_ILINES 32
+
+#define WAY0_L 0x1
+#define WAY1_L 0x2
+#define WAY01_L 0x3
+#define WAY2_L 0x4
+#define WAY02_L 0x5
+#define WAY12_L 0x6
+#define WAY012_L 0x7
+
+#define WAY3_L 0x8
+#define WAY03_L 0x9
+#define WAY13_L 0xA
+#define WAY013_L 0xB
+
+#define WAY32_L 0xC
+#define WAY320_L 0xD
+#define WAY321_L 0xE
+#define WAYALL_L 0xF
+
+#define DMC_ENABLE (2<<2) /*yes, 2, not 1 */
+
+/* IAR0 BIT FIELDS*/
+#define RTC_ERROR_BIT 0x0FFFFFFF
+#define UART_ERROR_BIT 0xF0FFFFFF
+#define SPORT1_ERROR_BIT 0xFF0FFFFF
+#define SPI_ERROR_BIT 0xFFF0FFFF
+#define SPORT0_ERROR_BIT 0xFFFF0FFF
+#define PPI_ERROR_BIT 0xFFFFF0FF
+#define DMA_ERROR_BIT 0xFFFFFF0F
+#define PLLWAKE_ERROR_BIT 0xFFFFFFFF
+
+/* IAR1 BIT FIELDS*/
+#define DMA7_UARTTX_BIT 0x0FFFFFFF
+#define DMA6_UARTRX_BIT 0xF0FFFFFF
+#define DMA5_SPI_BIT 0xFF0FFFFF
+#define DMA4_SPORT1TX_BIT 0xFFF0FFFF
+#define DMA3_SPORT1RX_BIT 0xFFFF0FFF
+#define DMA2_SPORT0TX_BIT 0xFFFFF0FF
+#define DMA1_SPORT0RX_BIT 0xFFFFFF0F
+#define DMA0_PPI_BIT 0xFFFFFFFF
+
+/* IAR2 BIT FIELDS*/
+#define WDTIMER_BIT 0x0FFFFFFF
+#define MEMDMA1_BIT 0xF0FFFFFF
+#define MEMDMA0_BIT 0xFF0FFFFF
+#define PFB_BIT 0xFFF0FFFF
+#define PFA_BIT 0xFFFF0FFF
+#define TIMER2_BIT 0xFFFFF0FF
+#define TIMER1_BIT 0xFFFFFF0F
+#define TIMER0_BIT 0xFFFFFFFF
+
+/********************************* EBIU Settings ************************************/
+#define AMBCTL0VAL ((CONFIG_BANK_1 << 16) | CONFIG_BANK_0)
+#define AMBCTL1VAL ((CONFIG_BANK_3 << 16) | CONFIG_BANK_2)
+
+#ifdef CONFIG_C_AMBEN_ALL
+#define V_AMBEN AMBEN_ALL
+#endif
+#ifdef CONFIG_C_AMBEN
+#define V_AMBEN 0x0
+#endif
+#ifdef CONFIG_C_AMBEN_B0
+#define V_AMBEN AMBEN_B0
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1
+#define V_AMBEN AMBEN_B0_B1
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1_B2
+#define V_AMBEN AMBEN_B0_B1_B2
+#endif
+#ifdef CONFIG_C_AMCKEN
+#define V_AMCKEN AMCKEN
+#else
+#define V_AMCKEN 0x0
+#endif
+#ifdef CONFIG_C_CDPRIO
+#define V_CDPRIO 0x100
+#else
+#define V_CDPRIO 0x0
+#endif
+
+#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO)
+
+#ifdef CONFIG_BF533
+#define CPU "BF533"
+#define CPUID 0x027a5000
+#endif
+#ifdef CONFIG_BF532
+#define CPU "BF532"
+#define CPUID 0x0275A000
+#endif
+#ifdef CONFIG_BF531
+#define CPU "BF531"
+#define CPUID 0x027a5000
+#endif
+#ifndef CPU
+#define CPU "UNKNOWN"
+#define CPUID 0x0
+#endif
+
+#endif /* __MACH_BF533_H__ */
diff --git a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
new file mode 100644
index 0000000..ebf592b
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
@@ -0,0 +1,164 @@
+/*
+ * file: include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ * blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs: enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose. see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define UART_GET_CHAR(uart) bfin_read16(((uart)->port.membase + OFFSET_RBR))
+#define UART_GET_DLL(uart) bfin_read16(((uart)->port.membase + OFFSET_DLL))
+#define UART_GET_IER(uart) bfin_read16(((uart)->port.membase + OFFSET_IER))
+#define UART_GET_DLH(uart) bfin_read16(((uart)->port.membase + OFFSET_DLH))
+#define UART_GET_IIR(uart) bfin_read16(((uart)->port.membase + OFFSET_IIR))
+#define UART_GET_LCR(uart) bfin_read16(((uart)->port.membase + OFFSET_LCR))
+#define UART_GET_GCTL(uart) bfin_read16(((uart)->port.membase + OFFSET_GCTL))
+
+#define UART_PUT_CHAR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_THR),v)
+#define UART_PUT_DLL(uart,v) bfin_write16(((uart)->port.membase + OFFSET_DLL),v)
+#define UART_PUT_IER(uart,v) bfin_write16(((uart)->port.membase + OFFSET_IER),v)
+#define UART_SET_IER(uart,v) UART_PUT_IER(uart, UART_GET_IER(uart) | (v))
+#define UART_CLEAR_IER(uart,v) UART_PUT_IER(uart, UART_GET_IER(uart) & ~(v))
+#define UART_PUT_DLH(uart,v) bfin_write16(((uart)->port.membase + OFFSET_DLH),v)
+#define UART_PUT_LCR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_LCR),v)
+#define UART_PUT_GCTL(uart,v) bfin_write16(((uart)->port.membase + OFFSET_GCTL),v)
+
+#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
+#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
+
+#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
+#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
+#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
+
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+# define CONFIG_SERIAL_BFIN_CTSRTS
+# ifndef CONFIG_UART0_CTS_PIN
+# define CONFIG_UART0_CTS_PIN -1
+# endif
+# ifndef CONFIG_UART0_RTS_PIN
+# define CONFIG_UART0_RTS_PIN -1
+# endif
+#endif
+
+struct bfin_serial_port {
+ struct uart_port port;
+ unsigned int old_status;
+ unsigned int lsr;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ int tx_done;
+ int tx_count;
+ struct circ_buf rx_dma_buf;
+ struct timer_list rx_dma_timer;
+ int rx_dma_nrows;
+ unsigned int tx_dma_channel;
+ unsigned int rx_dma_channel;
+ struct work_struct tx_dma_workqueue;
+#else
+# if ANOMALY_05000230
+ unsigned int anomaly_threshold;
+# endif
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ struct timer_list cts_timer;
+ int cts_pin;
+ int rts_pin;
+#endif
+};
+
+/* The hardware clears the LSR bits upon read, so we need to cache
+ * some of the more fun bits in software so they don't get lost
+ * when checking the LSR in other code paths (TX).
+ */
+static inline unsigned int UART_GET_LSR(struct bfin_serial_port *uart)
+{
+ unsigned int lsr = bfin_read16(uart->port.membase + OFFSET_LSR);
+ uart->lsr |= (lsr & (BI|FE|PE|OE));
+ return lsr | uart->lsr;
+}
+
+static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
+{
+ uart->lsr = 0;
+ bfin_write16(uart->port.membase + OFFSET_LSR, -1);
+}
+
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
+struct bfin_serial_res {
+ unsigned long uart_base_addr;
+ int uart_irq;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ unsigned int uart_tx_dma_channel;
+ unsigned int uart_rx_dma_channel;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ int uart_cts_pin;
+ int uart_rts_pin;
+#endif
+};
+
+struct bfin_serial_res bfin_serial_resource[] = {
+ {
+ 0xFFC00400,
+ IRQ_UART_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ CH_UART_TX,
+ CH_UART_RX,
+#endif
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+ CONFIG_UART0_CTS_PIN,
+ CONFIG_UART0_RTS_PIN,
+#endif
+ }
+};
+
+#define DRIVER_NAME "bfin-uart"
+
+int nr_ports = BFIN_UART_NR_PORTS;
+static void bfin_serial_hw_init(struct bfin_serial_port *uart)
+{
+
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ peripheral_request(P_UART0_TX, DRIVER_NAME);
+ peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0) {
+ gpio_request(uart->cts_pin, DRIVER_NAME);
+ gpio_direction_input(uart->cts_pin);
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_input(uart->rts_pin, 0);
+ }
+#endif
+}
diff --git a/arch/blackfin/mach-bf533/include/mach/bfin_sir.h b/arch/blackfin/mach-bf533/include/mach/bfin_sir.h
new file mode 100644
index 0000000..9bb87e9
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/bfin_sir.h
@@ -0,0 +1,125 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port) bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port) bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port) bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port) bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port) bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port) bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port) bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v) bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v) bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v) bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v) bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+ char *buf;
+ int head;
+ int tail;
+ };
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+ unsigned char __iomem *membase;
+ unsigned int irq;
+ unsigned int lsr;
+ unsigned long clk;
+ struct net_device *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+ int tx_done;
+ struct dma_rx_buf rx_dma_buf;
+ struct timer_list rx_dma_timer;
+ int rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+ unsigned int tx_dma_channel;
+ unsigned int rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+ unsigned long base_addr;
+ int irq;
+ unsigned int rx_dma_channel;
+ unsigned int tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+ {
+ 0xFFC00400,
+ IRQ_UART_RX,
+ CH_UART_RX,
+ CH_UART_TX,
+ },
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+ struct bfin_sir_port *sir_port;
+ spinlock_t lock;
+ unsigned int open;
+ int speed;
+ int newspeed;
+
+ struct sk_buff *txskb;
+ struct sk_buff *rxskb;
+ struct net_device_stats stats;
+ struct device *dev;
+ struct irlap_cb *irlap;
+ struct qos_info qos;
+
+ iobuff_t tx_buff;
+ iobuff_t rx_buff;
+
+ struct work_struct work;
+ int mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+ unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+ port->lsr |= (lsr & (BI|FE|PE|OE));
+ return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+ port->lsr = 0;
+ bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static int bfin_sir_hw_init(void)
+{
+ int ret = -ENODEV;
+#ifdef CONFIG_BFIN_SIR0
+ ret = peripheral_request(P_UART0_TX, DRIVER_NAME);
+ if (ret)
+ return ret;
+ ret = peripheral_request(P_UART0_RX, DRIVER_NAME);
+ if (ret)
+ return ret;
+#endif
+ return ret;
+}
diff --git a/arch/blackfin/mach-bf533/include/mach/blackfin.h b/arch/blackfin/mach-bf533/include/mach/blackfin.h
new file mode 100644
index 0000000..d80971b
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/blackfin.h
@@ -0,0 +1,60 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/blackfin.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _MACH_BLACKFIN_H_
+#define _MACH_BLACKFIN_H_
+
+#define BF533_FAMILY
+
+#include "bf533.h"
+#include "mem_map.h"
+#include "defBF532.h"
+#include "anomaly.h"
+
+#if !defined(__ASSEMBLY__)
+#include "cdefBF532.h"
+#endif
+
+#define BFIN_UART_NR_PORTS 1
+
+#define OFFSET_THR 0x00 /* Transmit Holding register */
+#define OFFSET_RBR 0x00 /* Receive Buffer register */
+#define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */
+#define OFFSET_IER 0x04 /* Interrupt Enable Register */
+#define OFFSET_DLH 0x04 /* Divisor Latch (High-Byte) */
+#define OFFSET_IIR 0x08 /* Interrupt Identification Register */
+#define OFFSET_LCR 0x0C /* Line Control Register */
+#define OFFSET_MCR 0x10 /* Modem Control Register */
+#define OFFSET_LSR 0x14 /* Line Status Register */
+#define OFFSET_MSR 0x18 /* Modem Status Register */
+#define OFFSET_SCR 0x1C /* SCR Scratch Register */
+#define OFFSET_GCTL 0x24 /* Global Control Register */
+
+#endif /* _MACH_BLACKFIN_H_ */
diff --git a/arch/blackfin/mach-bf533/include/mach/cdefBF532.h b/arch/blackfin/mach-bf533/include/mach/cdefBF532.h
new file mode 100644
index 0000000..3d8978a
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/cdefBF532.h
@@ -0,0 +1,767 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/cdefBF532.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF532_H
+#define _CDEF_BF532_H
+
+#include <asm/blackfin.h>
+
+/*include all Core registers and bit definitions*/
+#include "defBF532.h"
+
+/*include core specific register pointer definitions*/
+#include <asm/cdef_LPBlackfin.h>
+
+#include <asm/system.h>
+
+/* Clock and System Control (0xFFC0 0400-0xFFC0 07FF) */
+#define bfin_read_PLL_CTL() bfin_read16(PLL_CTL)
+/* Writing to PLL_CTL initiates a PLL relock sequence. */
+static __inline__ void bfin_write_PLL_CTL(unsigned int val)
+{
+ unsigned long flags, iwr;
+
+ if (val == bfin_read_PLL_CTL())
+ return;
+
+ local_irq_save(flags);
+ /* Enable the PLL Wakeup bit in SIC IWR */
+ iwr = bfin_read32(SIC_IWR);
+ /* Only allow PPL Wakeup) */
+ bfin_write32(SIC_IWR, IWR_ENABLE(0));
+
+ bfin_write16(PLL_CTL, val);
+ SSYNC();
+ asm("IDLE;");
+
+ bfin_write32(SIC_IWR, iwr);
+ local_irq_restore(flags);
+}
+#define bfin_read_PLL_STAT() bfin_read16(PLL_STAT)
+#define bfin_write_PLL_STAT(val) bfin_write16(PLL_STAT,val)
+#define bfin_read_PLL_LOCKCNT() bfin_read16(PLL_LOCKCNT)
+#define bfin_write_PLL_LOCKCNT(val) bfin_write16(PLL_LOCKCNT,val)
+#define bfin_read_CHIPID() bfin_read32(CHIPID)
+#define bfin_read_PLL_DIV() bfin_read16(PLL_DIV)
+#define bfin_write_PLL_DIV(val) bfin_write16(PLL_DIV,val)
+#define bfin_read_VR_CTL() bfin_read16(VR_CTL)
+/* Writing to VR_CTL initiates a PLL relock sequence. */
+static __inline__ void bfin_write_VR_CTL(unsigned int val)
+{
+ unsigned long flags, iwr;
+
+ if (val == bfin_read_VR_CTL())
+ return;
+
+ local_irq_save(flags);
+ /* Enable the PLL Wakeup bit in SIC IWR */
+ iwr = bfin_read32(SIC_IWR);
+ /* Only allow PPL Wakeup) */
+ bfin_write32(SIC_IWR, IWR_ENABLE(0));
+
+ bfin_write16(VR_CTL, val);
+ SSYNC();
+ asm("IDLE;");
+
+ bfin_write32(SIC_IWR, iwr);
+ local_irq_restore(flags);
+}
+
+/* System Interrupt Controller (0xFFC0 0C00-0xFFC0 0FFF) */
+#define bfin_read_SWRST() bfin_read16(SWRST)
+#define bfin_write_SWRST(val) bfin_write16(SWRST,val)
+#define bfin_read_SYSCR() bfin_read16(SYSCR)
+#define bfin_write_SYSCR(val) bfin_write16(SYSCR,val)
+#define bfin_read_SIC_IAR0() bfin_read32(SIC_IAR0)
+#define bfin_write_SIC_IAR0(val) bfin_write32(SIC_IAR0,val)
+#define bfin_read_SIC_IAR1() bfin_read32(SIC_IAR1)
+#define bfin_write_SIC_IAR1(val) bfin_write32(SIC_IAR1,val)
+#define bfin_read_SIC_IAR2() bfin_read32(SIC_IAR2)
+#define bfin_write_SIC_IAR2(val) bfin_write32(SIC_IAR2,val)
+#define bfin_read_SIC_IAR3() bfin_read32(SIC_IAR3)
+#define bfin_write_SIC_IAR3(val) bfin_write32(SIC_IAR3,val)
+#define bfin_read_SIC_IMASK() bfin_read32(SIC_IMASK)
+#define bfin_write_SIC_IMASK(val) bfin_write32(SIC_IMASK,val)
+#define bfin_read_SIC_ISR() bfin_read32(SIC_ISR)
+#define bfin_write_SIC_ISR(val) bfin_write32(SIC_ISR,val)
+#define bfin_read_SIC_IWR() bfin_read32(SIC_IWR)
+#define bfin_write_SIC_IWR(val) bfin_write32(SIC_IWR,val)
+
+/* Watchdog Timer (0xFFC0 1000-0xFFC0 13FF) */
+#define bfin_read_WDOG_CTL() bfin_read16(WDOG_CTL)
+#define bfin_write_WDOG_CTL(val) bfin_write16(WDOG_CTL,val)
+#define bfin_read_WDOG_CNT() bfin_read32(WDOG_CNT)
+#define bfin_write_WDOG_CNT(val) bfin_write32(WDOG_CNT,val)
+#define bfin_read_WDOG_STAT() bfin_read32(WDOG_STAT)
+#define bfin_write_WDOG_STAT(val) bfin_write32(WDOG_STAT,val)
+
+/* Real Time Clock (0xFFC0 1400-0xFFC0 17FF) */
+#define bfin_read_RTC_STAT() bfin_read32(RTC_STAT)
+#define bfin_write_RTC_STAT(val) bfin_write32(RTC_STAT,val)
+#define bfin_read_RTC_ICTL() bfin_read16(RTC_ICTL)
+#define bfin_write_RTC_ICTL(val) bfin_write16(RTC_ICTL,val)
+#define bfin_read_RTC_ISTAT() bfin_read16(RTC_ISTAT)
+#define bfin_write_RTC_ISTAT(val) bfin_write16(RTC_ISTAT,val)
+#define bfin_read_RTC_SWCNT() bfin_read16(RTC_SWCNT)
+#define bfin_write_RTC_SWCNT(val) bfin_write16(RTC_SWCNT,val)
+#define bfin_read_RTC_ALARM() bfin_read32(RTC_ALARM)
+#define bfin_write_RTC_ALARM(val) bfin_write32(RTC_ALARM,val)
+#define bfin_read_RTC_FAST() bfin_read16(RTC_FAST)
+#define bfin_write_RTC_FAST(val) bfin_write16(RTC_FAST,val)
+#define bfin_read_RTC_PREN() bfin_read16(RTC_PREN)
+#define bfin_write_RTC_PREN(val) bfin_write16(RTC_PREN,val)
+
+/* DMA Traffic controls */
+#define bfin_read_DMA_TCPER() bfin_read16(DMA_TCPER)
+#define bfin_write_DMA_TCPER(val) bfin_write16(DMA_TCPER,val)
+#define bfin_read_DMA_TCCNT() bfin_read16(DMA_TCCNT)
+#define bfin_write_DMA_TCCNT(val) bfin_write16(DMA_TCCNT,val)
+
+/* Alternate deprecated register names (below) provided for backwards code compatibility */
+#define bfin_read_DMA_TC_PER() bfin_read16(DMA_TC_PER)
+#define bfin_write_DMA_TC_PER(val) bfin_write16(DMA_TC_PER,val)
+#define bfin_read_DMA_TC_CNT() bfin_read16(DMA_TC_CNT)
+#define bfin_write_DMA_TC_CNT(val) bfin_write16(DMA_TC_CNT,val)
+
+/* General Purpose IO (0xFFC0 2400-0xFFC0 27FF) */
+#define bfin_read_FIO_DIR() bfin_read16(FIO_DIR)
+#define bfin_write_FIO_DIR(val) bfin_write16(FIO_DIR,val)
+#define bfin_read_FIO_MASKA_C() bfin_read16(FIO_MASKA_C)
+#define bfin_write_FIO_MASKA_C(val) bfin_write16(FIO_MASKA_C,val)
+#define bfin_read_FIO_MASKA_S() bfin_read16(FIO_MASKA_S)
+#define bfin_write_FIO_MASKA_S(val) bfin_write16(FIO_MASKA_S,val)
+#define bfin_read_FIO_MASKB_C() bfin_read16(FIO_MASKB_C)
+#define bfin_write_FIO_MASKB_C(val) bfin_write16(FIO_MASKB_C,val)
+#define bfin_read_FIO_MASKB_S() bfin_read16(FIO_MASKB_S)
+#define bfin_write_FIO_MASKB_S(val) bfin_write16(FIO_MASKB_S,val)
+#define bfin_read_FIO_POLAR() bfin_read16(FIO_POLAR)
+#define bfin_write_FIO_POLAR(val) bfin_write16(FIO_POLAR,val)
+#define bfin_read_FIO_EDGE() bfin_read16(FIO_EDGE)
+#define bfin_write_FIO_EDGE(val) bfin_write16(FIO_EDGE,val)
+#define bfin_read_FIO_BOTH() bfin_read16(FIO_BOTH)
+#define bfin_write_FIO_BOTH(val) bfin_write16(FIO_BOTH,val)
+#define bfin_read_FIO_INEN() bfin_read16(FIO_INEN)
+#define bfin_write_FIO_INEN(val) bfin_write16(FIO_INEN,val)
+#define bfin_read_FIO_MASKA_D() bfin_read16(FIO_MASKA_D)
+#define bfin_write_FIO_MASKA_D(val) bfin_write16(FIO_MASKA_D,val)
+#define bfin_read_FIO_MASKA_T() bfin_read16(FIO_MASKA_T)
+#define bfin_write_FIO_MASKA_T(val) bfin_write16(FIO_MASKA_T,val)
+#define bfin_read_FIO_MASKB_D() bfin_read16(FIO_MASKB_D)
+#define bfin_write_FIO_MASKB_D(val) bfin_write16(FIO_MASKB_D,val)
+#define bfin_read_FIO_MASKB_T() bfin_read16(FIO_MASKB_T)
+#define bfin_write_FIO_MASKB_T(val) bfin_write16(FIO_MASKB_T,val)
+
+
+#if ANOMALY_05000311
+#define BFIN_WRITE_FIO_FLAG(name) \
+static __inline__ void bfin_write_FIO_FLAG_ ## name (unsigned short val)\
+{\
+ unsigned long flags;\
+ local_irq_save(flags);\
+ bfin_write16(FIO_FLAG_ ## name,val);\
+ bfin_read_CHIPID();\
+ local_irq_restore(flags);\
+}
+BFIN_WRITE_FIO_FLAG(D)
+BFIN_WRITE_FIO_FLAG(C)
+BFIN_WRITE_FIO_FLAG(S)
+BFIN_WRITE_FIO_FLAG(T)
+
+#define BFIN_READ_FIO_FLAG(name) \
+static __inline__ unsigned short bfin_read_FIO_FLAG_ ## name (void)\
+{\
+ unsigned long flags;\
+ unsigned short ret;\
+ local_irq_save(flags);\
+ ret = bfin_read16(FIO_FLAG_ ## name);\
+ bfin_read_CHIPID();\
+ local_irq_restore(flags);\
+ return ret;\
+}
+BFIN_READ_FIO_FLAG(D)
+BFIN_READ_FIO_FLAG(C)
+BFIN_READ_FIO_FLAG(S)
+BFIN_READ_FIO_FLAG(T)
+
+#else
+#define bfin_write_FIO_FLAG_D(val) bfin_write16(FIO_FLAG_D,val)
+#define bfin_write_FIO_FLAG_C(val) bfin_write16(FIO_FLAG_C,val)
+#define bfin_write_FIO_FLAG_S(val) bfin_write16(FIO_FLAG_S,val)
+#define bfin_write_FIO_FLAG_T(val) bfin_write16(FIO_FLAG_T,val)
+#define bfin_read_FIO_FLAG_T() bfin_read16(FIO_FLAG_T)
+#define bfin_read_FIO_FLAG_C() bfin_read16(FIO_FLAG_C)
+#define bfin_read_FIO_FLAG_S() bfin_read16(FIO_FLAG_S)
+#define bfin_read_FIO_FLAG_D() bfin_read16(FIO_FLAG_D)
+#endif
+
+
+/* DMA Controller */
+#define bfin_read_DMA0_CONFIG() bfin_read16(DMA0_CONFIG)
+#define bfin_write_DMA0_CONFIG(val) bfin_write16(DMA0_CONFIG,val)
+#define bfin_read_DMA0_NEXT_DESC_PTR() bfin_read32(DMA0_NEXT_DESC_PTR)
+#define bfin_write_DMA0_NEXT_DESC_PTR(val) bfin_write32(DMA0_NEXT_DESC_PTR,val)
+#define bfin_read_DMA0_START_ADDR() bfin_read32(DMA0_START_ADDR)
+#define bfin_write_DMA0_START_ADDR(val) bfin_write32(DMA0_START_ADDR,val)
+#define bfin_read_DMA0_X_COUNT() bfin_read16(DMA0_X_COUNT)
+#define bfin_write_DMA0_X_COUNT(val) bfin_write16(DMA0_X_COUNT,val)
+#define bfin_read_DMA0_Y_COUNT() bfin_read16(DMA0_Y_COUNT)
+#define bfin_write_DMA0_Y_COUNT(val) bfin_write16(DMA0_Y_COUNT,val)
+#define bfin_read_DMA0_X_MODIFY() bfin_read16(DMA0_X_MODIFY)
+#define bfin_write_DMA0_X_MODIFY(val) bfin_write16(DMA0_X_MODIFY,val)
+#define bfin_read_DMA0_Y_MODIFY() bfin_read16(DMA0_Y_MODIFY)
+#define bfin_write_DMA0_Y_MODIFY(val) bfin_write16(DMA0_Y_MODIFY,val)
+#define bfin_read_DMA0_CURR_DESC_PTR() bfin_read32(DMA0_CURR_DESC_PTR)
+#define bfin_write_DMA0_CURR_DESC_PTR(val) bfin_write32(DMA0_CURR_DESC_PTR,val)
+#define bfin_read_DMA0_CURR_ADDR() bfin_read32(DMA0_CURR_ADDR)
+#define bfin_write_DMA0_CURR_ADDR(val) bfin_write32(DMA0_CURR_ADDR,val)
+#define bfin_read_DMA0_CURR_X_COUNT() bfin_read16(DMA0_CURR_X_COUNT)
+#define bfin_write_DMA0_CURR_X_COUNT(val) bfin_write16(DMA0_CURR_X_COUNT,val)
+#define bfin_read_DMA0_CURR_Y_COUNT() bfin_read16(DMA0_CURR_Y_COUNT)
+#define bfin_write_DMA0_CURR_Y_COUNT(val) bfin_write16(DMA0_CURR_Y_COUNT,val)
+#define bfin_read_DMA0_IRQ_STATUS() bfin_read16(DMA0_IRQ_STATUS)
+#define bfin_write_DMA0_IRQ_STATUS(val) bfin_write16(DMA0_IRQ_STATUS,val)
+#define bfin_read_DMA0_PERIPHERAL_MAP() bfin_read16(DMA0_PERIPHERAL_MAP)
+#define bfin_write_DMA0_PERIPHERAL_MAP(val) bfin_write16(DMA0_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA1_CONFIG() bfin_read16(DMA1_CONFIG)
+#define bfin_write_DMA1_CONFIG(val) bfin_write16(DMA1_CONFIG,val)
+#define bfin_read_DMA1_NEXT_DESC_PTR() bfin_read32(DMA1_NEXT_DESC_PTR)
+#define bfin_write_DMA1_NEXT_DESC_PTR(val) bfin_write32(DMA1_NEXT_DESC_PTR,val)
+#define bfin_read_DMA1_START_ADDR() bfin_read32(DMA1_START_ADDR)
+#define bfin_write_DMA1_START_ADDR(val) bfin_write32(DMA1_START_ADDR,val)
+#define bfin_read_DMA1_X_COUNT() bfin_read16(DMA1_X_COUNT)
+#define bfin_write_DMA1_X_COUNT(val) bfin_write16(DMA1_X_COUNT,val)
+#define bfin_read_DMA1_Y_COUNT() bfin_read16(DMA1_Y_COUNT)
+#define bfin_write_DMA1_Y_COUNT(val) bfin_write16(DMA1_Y_COUNT,val)
+#define bfin_read_DMA1_X_MODIFY() bfin_read16(DMA1_X_MODIFY)
+#define bfin_write_DMA1_X_MODIFY(val) bfin_write16(DMA1_X_MODIFY,val)
+#define bfin_read_DMA1_Y_MODIFY() bfin_read16(DMA1_Y_MODIFY)
+#define bfin_write_DMA1_Y_MODIFY(val) bfin_write16(DMA1_Y_MODIFY,val)
+#define bfin_read_DMA1_CURR_DESC_PTR() bfin_read32(DMA1_CURR_DESC_PTR)
+#define bfin_write_DMA1_CURR_DESC_PTR(val) bfin_write32(DMA1_CURR_DESC_PTR,val)
+#define bfin_read_DMA1_CURR_ADDR() bfin_read32(DMA1_CURR_ADDR)
+#define bfin_write_DMA1_CURR_ADDR(val) bfin_write32(DMA1_CURR_ADDR,val)
+#define bfin_read_DMA1_CURR_X_COUNT() bfin_read16(DMA1_CURR_X_COUNT)
+#define bfin_write_DMA1_CURR_X_COUNT(val) bfin_write16(DMA1_CURR_X_COUNT,val)
+#define bfin_read_DMA1_CURR_Y_COUNT() bfin_read16(DMA1_CURR_Y_COUNT)
+#define bfin_write_DMA1_CURR_Y_COUNT(val) bfin_write16(DMA1_CURR_Y_COUNT,val)
+#define bfin_read_DMA1_IRQ_STATUS() bfin_read16(DMA1_IRQ_STATUS)
+#define bfin_write_DMA1_IRQ_STATUS(val) bfin_write16(DMA1_IRQ_STATUS,val)
+#define bfin_read_DMA1_PERIPHERAL_MAP() bfin_read16(DMA1_PERIPHERAL_MAP)
+#define bfin_write_DMA1_PERIPHERAL_MAP(val) bfin_write16(DMA1_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA2_CONFIG() bfin_read16(DMA2_CONFIG)
+#define bfin_write_DMA2_CONFIG(val) bfin_write16(DMA2_CONFIG,val)
+#define bfin_read_DMA2_NEXT_DESC_PTR() bfin_read32(DMA2_NEXT_DESC_PTR)
+#define bfin_write_DMA2_NEXT_DESC_PTR(val) bfin_write32(DMA2_NEXT_DESC_PTR,val)
+#define bfin_read_DMA2_START_ADDR() bfin_read32(DMA2_START_ADDR)
+#define bfin_write_DMA2_START_ADDR(val) bfin_write32(DMA2_START_ADDR,val)
+#define bfin_read_DMA2_X_COUNT() bfin_read16(DMA2_X_COUNT)
+#define bfin_write_DMA2_X_COUNT(val) bfin_write16(DMA2_X_COUNT,val)
+#define bfin_read_DMA2_Y_COUNT() bfin_read16(DMA2_Y_COUNT)
+#define bfin_write_DMA2_Y_COUNT(val) bfin_write16(DMA2_Y_COUNT,val)
+#define bfin_read_DMA2_X_MODIFY() bfin_read16(DMA2_X_MODIFY)
+#define bfin_write_DMA2_X_MODIFY(val) bfin_write16(DMA2_X_MODIFY,val)
+#define bfin_read_DMA2_Y_MODIFY() bfin_read16(DMA2_Y_MODIFY)
+#define bfin_write_DMA2_Y_MODIFY(val) bfin_write16(DMA2_Y_MODIFY,val)
+#define bfin_read_DMA2_CURR_DESC_PTR() bfin_read32(DMA2_CURR_DESC_PTR)
+#define bfin_write_DMA2_CURR_DESC_PTR(val) bfin_write32(DMA2_CURR_DESC_PTR,val)
+#define bfin_read_DMA2_CURR_ADDR() bfin_read32(DMA2_CURR_ADDR)
+#define bfin_write_DMA2_CURR_ADDR(val) bfin_write32(DMA2_CURR_ADDR,val)
+#define bfin_read_DMA2_CURR_X_COUNT() bfin_read16(DMA2_CURR_X_COUNT)
+#define bfin_write_DMA2_CURR_X_COUNT(val) bfin_write16(DMA2_CURR_X_COUNT,val)
+#define bfin_read_DMA2_CURR_Y_COUNT() bfin_read16(DMA2_CURR_Y_COUNT)
+#define bfin_write_DMA2_CURR_Y_COUNT(val) bfin_write16(DMA2_CURR_Y_COUNT,val)
+#define bfin_read_DMA2_IRQ_STATUS() bfin_read16(DMA2_IRQ_STATUS)
+#define bfin_write_DMA2_IRQ_STATUS(val) bfin_write16(DMA2_IRQ_STATUS,val)
+#define bfin_read_DMA2_PERIPHERAL_MAP() bfin_read16(DMA2_PERIPHERAL_MAP)
+#define bfin_write_DMA2_PERIPHERAL_MAP(val) bfin_write16(DMA2_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA3_CONFIG() bfin_read16(DMA3_CONFIG)
+#define bfin_write_DMA3_CONFIG(val) bfin_write16(DMA3_CONFIG,val)
+#define bfin_read_DMA3_NEXT_DESC_PTR() bfin_read32(DMA3_NEXT_DESC_PTR)
+#define bfin_write_DMA3_NEXT_DESC_PTR(val) bfin_write32(DMA3_NEXT_DESC_PTR,val)
+#define bfin_read_DMA3_START_ADDR() bfin_read32(DMA3_START_ADDR)
+#define bfin_write_DMA3_START_ADDR(val) bfin_write32(DMA3_START_ADDR,val)
+#define bfin_read_DMA3_X_COUNT() bfin_read16(DMA3_X_COUNT)
+#define bfin_write_DMA3_X_COUNT(val) bfin_write16(DMA3_X_COUNT,val)
+#define bfin_read_DMA3_Y_COUNT() bfin_read16(DMA3_Y_COUNT)
+#define bfin_write_DMA3_Y_COUNT(val) bfin_write16(DMA3_Y_COUNT,val)
+#define bfin_read_DMA3_X_MODIFY() bfin_read16(DMA3_X_MODIFY)
+#define bfin_write_DMA3_X_MODIFY(val) bfin_write16(DMA3_X_MODIFY,val)
+#define bfin_read_DMA3_Y_MODIFY() bfin_read16(DMA3_Y_MODIFY)
+#define bfin_write_DMA3_Y_MODIFY(val) bfin_write16(DMA3_Y_MODIFY,val)
+#define bfin_read_DMA3_CURR_DESC_PTR() bfin_read32(DMA3_CURR_DESC_PTR)
+#define bfin_write_DMA3_CURR_DESC_PTR(val) bfin_write32(DMA3_CURR_DESC_PTR,val)
+#define bfin_read_DMA3_CURR_ADDR() bfin_read32(DMA3_CURR_ADDR)
+#define bfin_write_DMA3_CURR_ADDR(val) bfin_write32(DMA3_CURR_ADDR,val)
+#define bfin_read_DMA3_CURR_X_COUNT() bfin_read16(DMA3_CURR_X_COUNT)
+#define bfin_write_DMA3_CURR_X_COUNT(val) bfin_write16(DMA3_CURR_X_COUNT,val)
+#define bfin_read_DMA3_CURR_Y_COUNT() bfin_read16(DMA3_CURR_Y_COUNT)
+#define bfin_write_DMA3_CURR_Y_COUNT(val) bfin_write16(DMA3_CURR_Y_COUNT,val)
+#define bfin_read_DMA3_IRQ_STATUS() bfin_read16(DMA3_IRQ_STATUS)
+#define bfin_write_DMA3_IRQ_STATUS(val) bfin_write16(DMA3_IRQ_STATUS,val)
+#define bfin_read_DMA3_PERIPHERAL_MAP() bfin_read16(DMA3_PERIPHERAL_MAP)
+#define bfin_write_DMA3_PERIPHERAL_MAP(val) bfin_write16(DMA3_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA4_CONFIG() bfin_read16(DMA4_CONFIG)
+#define bfin_write_DMA4_CONFIG(val) bfin_write16(DMA4_CONFIG,val)
+#define bfin_read_DMA4_NEXT_DESC_PTR() bfin_read32(DMA4_NEXT_DESC_PTR)
+#define bfin_write_DMA4_NEXT_DESC_PTR(val) bfin_write32(DMA4_NEXT_DESC_PTR,val)
+#define bfin_read_DMA4_START_ADDR() bfin_read32(DMA4_START_ADDR)
+#define bfin_write_DMA4_START_ADDR(val) bfin_write32(DMA4_START_ADDR,val)
+#define bfin_read_DMA4_X_COUNT() bfin_read16(DMA4_X_COUNT)
+#define bfin_write_DMA4_X_COUNT(val) bfin_write16(DMA4_X_COUNT,val)
+#define bfin_read_DMA4_Y_COUNT() bfin_read16(DMA4_Y_COUNT)
+#define bfin_write_DMA4_Y_COUNT(val) bfin_write16(DMA4_Y_COUNT,val)
+#define bfin_read_DMA4_X_MODIFY() bfin_read16(DMA4_X_MODIFY)
+#define bfin_write_DMA4_X_MODIFY(val) bfin_write16(DMA4_X_MODIFY,val)
+#define bfin_read_DMA4_Y_MODIFY() bfin_read16(DMA4_Y_MODIFY)
+#define bfin_write_DMA4_Y_MODIFY(val) bfin_write16(DMA4_Y_MODIFY,val)
+#define bfin_read_DMA4_CURR_DESC_PTR() bfin_read32(DMA4_CURR_DESC_PTR)
+#define bfin_write_DMA4_CURR_DESC_PTR(val) bfin_write32(DMA4_CURR_DESC_PTR,val)
+#define bfin_read_DMA4_CURR_ADDR() bfin_read32(DMA4_CURR_ADDR)
+#define bfin_write_DMA4_CURR_ADDR(val) bfin_write32(DMA4_CURR_ADDR,val)
+#define bfin_read_DMA4_CURR_X_COUNT() bfin_read16(DMA4_CURR_X_COUNT)
+#define bfin_write_DMA4_CURR_X_COUNT(val) bfin_write16(DMA4_CURR_X_COUNT,val)
+#define bfin_read_DMA4_CURR_Y_COUNT() bfin_read16(DMA4_CURR_Y_COUNT)
+#define bfin_write_DMA4_CURR_Y_COUNT(val) bfin_write16(DMA4_CURR_Y_COUNT,val)
+#define bfin_read_DMA4_IRQ_STATUS() bfin_read16(DMA4_IRQ_STATUS)
+#define bfin_write_DMA4_IRQ_STATUS(val) bfin_write16(DMA4_IRQ_STATUS,val)
+#define bfin_read_DMA4_PERIPHERAL_MAP() bfin_read16(DMA4_PERIPHERAL_MAP)
+#define bfin_write_DMA4_PERIPHERAL_MAP(val) bfin_write16(DMA4_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA5_CONFIG() bfin_read16(DMA5_CONFIG)
+#define bfin_write_DMA5_CONFIG(val) bfin_write16(DMA5_CONFIG,val)
+#define bfin_read_DMA5_NEXT_DESC_PTR() bfin_read32(DMA5_NEXT_DESC_PTR)
+#define bfin_write_DMA5_NEXT_DESC_PTR(val) bfin_write32(DMA5_NEXT_DESC_PTR,val)
+#define bfin_read_DMA5_START_ADDR() bfin_read32(DMA5_START_ADDR)
+#define bfin_write_DMA5_START_ADDR(val) bfin_write32(DMA5_START_ADDR,val)
+#define bfin_read_DMA5_X_COUNT() bfin_read16(DMA5_X_COUNT)
+#define bfin_write_DMA5_X_COUNT(val) bfin_write16(DMA5_X_COUNT,val)
+#define bfin_read_DMA5_Y_COUNT() bfin_read16(DMA5_Y_COUNT)
+#define bfin_write_DMA5_Y_COUNT(val) bfin_write16(DMA5_Y_COUNT,val)
+#define bfin_read_DMA5_X_MODIFY() bfin_read16(DMA5_X_MODIFY)
+#define bfin_write_DMA5_X_MODIFY(val) bfin_write16(DMA5_X_MODIFY,val)
+#define bfin_read_DMA5_Y_MODIFY() bfin_read16(DMA5_Y_MODIFY)
+#define bfin_write_DMA5_Y_MODIFY(val) bfin_write16(DMA5_Y_MODIFY,val)
+#define bfin_read_DMA5_CURR_DESC_PTR() bfin_read32(DMA5_CURR_DESC_PTR)
+#define bfin_write_DMA5_CURR_DESC_PTR(val) bfin_write32(DMA5_CURR_DESC_PTR,val)
+#define bfin_read_DMA5_CURR_ADDR() bfin_read32(DMA5_CURR_ADDR)
+#define bfin_write_DMA5_CURR_ADDR(val) bfin_write32(DMA5_CURR_ADDR,val)
+#define bfin_read_DMA5_CURR_X_COUNT() bfin_read16(DMA5_CURR_X_COUNT)
+#define bfin_write_DMA5_CURR_X_COUNT(val) bfin_write16(DMA5_CURR_X_COUNT,val)
+#define bfin_read_DMA5_CURR_Y_COUNT() bfin_read16(DMA5_CURR_Y_COUNT)
+#define bfin_write_DMA5_CURR_Y_COUNT(val) bfin_write16(DMA5_CURR_Y_COUNT,val)
+#define bfin_read_DMA5_IRQ_STATUS() bfin_read16(DMA5_IRQ_STATUS)
+#define bfin_write_DMA5_IRQ_STATUS(val) bfin_write16(DMA5_IRQ_STATUS,val)
+#define bfin_read_DMA5_PERIPHERAL_MAP() bfin_read16(DMA5_PERIPHERAL_MAP)
+#define bfin_write_DMA5_PERIPHERAL_MAP(val) bfin_write16(DMA5_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA6_CONFIG() bfin_read16(DMA6_CONFIG)
+#define bfin_write_DMA6_CONFIG(val) bfin_write16(DMA6_CONFIG,val)
+#define bfin_read_DMA6_NEXT_DESC_PTR() bfin_read32(DMA6_NEXT_DESC_PTR)
+#define bfin_write_DMA6_NEXT_DESC_PTR(val) bfin_write32(DMA6_NEXT_DESC_PTR,val)
+#define bfin_read_DMA6_START_ADDR() bfin_read32(DMA6_START_ADDR)
+#define bfin_write_DMA6_START_ADDR(val) bfin_write32(DMA6_START_ADDR,val)
+#define bfin_read_DMA6_X_COUNT() bfin_read16(DMA6_X_COUNT)
+#define bfin_write_DMA6_X_COUNT(val) bfin_write16(DMA6_X_COUNT,val)
+#define bfin_read_DMA6_Y_COUNT() bfin_read16(DMA6_Y_COUNT)
+#define bfin_write_DMA6_Y_COUNT(val) bfin_write16(DMA6_Y_COUNT,val)
+#define bfin_read_DMA6_X_MODIFY() bfin_read16(DMA6_X_MODIFY)
+#define bfin_write_DMA6_X_MODIFY(val) bfin_write16(DMA6_X_MODIFY,val)
+#define bfin_read_DMA6_Y_MODIFY() bfin_read16(DMA6_Y_MODIFY)
+#define bfin_write_DMA6_Y_MODIFY(val) bfin_write16(DMA6_Y_MODIFY,val)
+#define bfin_read_DMA6_CURR_DESC_PTR() bfin_read32(DMA6_CURR_DESC_PTR)
+#define bfin_write_DMA6_CURR_DESC_PTR(val) bfin_write32(DMA6_CURR_DESC_PTR,val)
+#define bfin_read_DMA6_CURR_ADDR() bfin_read32(DMA6_CURR_ADDR)
+#define bfin_write_DMA6_CURR_ADDR(val) bfin_write32(DMA6_CURR_ADDR,val)
+#define bfin_read_DMA6_CURR_X_COUNT() bfin_read16(DMA6_CURR_X_COUNT)
+#define bfin_write_DMA6_CURR_X_COUNT(val) bfin_write16(DMA6_CURR_X_COUNT,val)
+#define bfin_read_DMA6_CURR_Y_COUNT() bfin_read16(DMA6_CURR_Y_COUNT)
+#define bfin_write_DMA6_CURR_Y_COUNT(val) bfin_write16(DMA6_CURR_Y_COUNT,val)
+#define bfin_read_DMA6_IRQ_STATUS() bfin_read16(DMA6_IRQ_STATUS)
+#define bfin_write_DMA6_IRQ_STATUS(val) bfin_write16(DMA6_IRQ_STATUS,val)
+#define bfin_read_DMA6_PERIPHERAL_MAP() bfin_read16(DMA6_PERIPHERAL_MAP)
+#define bfin_write_DMA6_PERIPHERAL_MAP(val) bfin_write16(DMA6_PERIPHERAL_MAP,val)
+
+#define bfin_read_DMA7_CONFIG() bfin_read16(DMA7_CONFIG)
+#define bfin_write_DMA7_CONFIG(val) bfin_write16(DMA7_CONFIG,val)
+#define bfin_read_DMA7_NEXT_DESC_PTR() bfin_read32(DMA7_NEXT_DESC_PTR)
+#define bfin_write_DMA7_NEXT_DESC_PTR(val) bfin_write32(DMA7_NEXT_DESC_PTR,val)
+#define bfin_read_DMA7_START_ADDR() bfin_read32(DMA7_START_ADDR)
+#define bfin_write_DMA7_START_ADDR(val) bfin_write32(DMA7_START_ADDR,val)
+#define bfin_read_DMA7_X_COUNT() bfin_read16(DMA7_X_COUNT)
+#define bfin_write_DMA7_X_COUNT(val) bfin_write16(DMA7_X_COUNT,val)
+#define bfin_read_DMA7_Y_COUNT() bfin_read16(DMA7_Y_COUNT)
+#define bfin_write_DMA7_Y_COUNT(val) bfin_write16(DMA7_Y_COUNT,val)
+#define bfin_read_DMA7_X_MODIFY() bfin_read16(DMA7_X_MODIFY)
+#define bfin_write_DMA7_X_MODIFY(val) bfin_write16(DMA7_X_MODIFY,val)
+#define bfin_read_DMA7_Y_MODIFY() bfin_read16(DMA7_Y_MODIFY)
+#define bfin_write_DMA7_Y_MODIFY(val) bfin_write16(DMA7_Y_MODIFY,val)
+#define bfin_read_DMA7_CURR_DESC_PTR() bfin_read32(DMA7_CURR_DESC_PTR)
+#define bfin_write_DMA7_CURR_DESC_PTR(val) bfin_write32(DMA7_CURR_DESC_PTR,val)
+#define bfin_read_DMA7_CURR_ADDR() bfin_read32(DMA7_CURR_ADDR)
+#define bfin_write_DMA7_CURR_ADDR(val) bfin_write32(DMA7_CURR_ADDR,val)
+#define bfin_read_DMA7_CURR_X_COUNT() bfin_read16(DMA7_CURR_X_COUNT)
+#define bfin_write_DMA7_CURR_X_COUNT(val) bfin_write16(DMA7_CURR_X_COUNT,val)
+#define bfin_read_DMA7_CURR_Y_COUNT() bfin_read16(DMA7_CURR_Y_COUNT)
+#define bfin_write_DMA7_CURR_Y_COUNT(val) bfin_write16(DMA7_CURR_Y_COUNT,val)
+#define bfin_read_DMA7_IRQ_STATUS() bfin_read16(DMA7_IRQ_STATUS)
+#define bfin_write_DMA7_IRQ_STATUS(val) bfin_write16(DMA7_IRQ_STATUS,val)
+#define bfin_read_DMA7_PERIPHERAL_MAP() bfin_read16(DMA7_PERIPHERAL_MAP)
+#define bfin_write_DMA7_PERIPHERAL_MAP(val) bfin_write16(DMA7_PERIPHERAL_MAP,val)
+
+#define bfin_read_MDMA_D1_CONFIG() bfin_read16(MDMA_D1_CONFIG)
+#define bfin_write_MDMA_D1_CONFIG(val) bfin_write16(MDMA_D1_CONFIG,val)
+#define bfin_read_MDMA_D1_NEXT_DESC_PTR() bfin_read32(MDMA_D1_NEXT_DESC_PTR)
+#define bfin_write_MDMA_D1_NEXT_DESC_PTR(val) bfin_write32(MDMA_D1_NEXT_DESC_PTR,val)
+#define bfin_read_MDMA_D1_START_ADDR() bfin_read32(MDMA_D1_START_ADDR)
+#define bfin_write_MDMA_D1_START_ADDR(val) bfin_write32(MDMA_D1_START_ADDR,val)
+#define bfin_read_MDMA_D1_X_COUNT() bfin_read16(MDMA_D1_X_COUNT)
+#define bfin_write_MDMA_D1_X_COUNT(val) bfin_write16(MDMA_D1_X_COUNT,val)
+#define bfin_read_MDMA_D1_Y_COUNT() bfin_read16(MDMA_D1_Y_COUNT)
+#define bfin_write_MDMA_D1_Y_COUNT(val) bfin_write16(MDMA_D1_Y_COUNT,val)
+#define bfin_read_MDMA_D1_X_MODIFY() bfin_read16(MDMA_D1_X_MODIFY)
+#define bfin_write_MDMA_D1_X_MODIFY(val) bfin_write16(MDMA_D1_X_MODIFY,val)
+#define bfin_read_MDMA_D1_Y_MODIFY() bfin_read16(MDMA_D1_Y_MODIFY)
+#define bfin_write_MDMA_D1_Y_MODIFY(val) bfin_write16(MDMA_D1_Y_MODIFY,val)
+#define bfin_read_MDMA_D1_CURR_DESC_PTR() bfin_read32(MDMA_D1_CURR_DESC_PTR)
+#define bfin_write_MDMA_D1_CURR_DESC_PTR(val) bfin_write32(MDMA_D1_CURR_DESC_PTR,val)
+#define bfin_read_MDMA_D1_CURR_ADDR() bfin_read32(MDMA_D1_CURR_ADDR)
+#define bfin_write_MDMA_D1_CURR_ADDR(val) bfin_write32(MDMA_D1_CURR_ADDR,val)
+#define bfin_read_MDMA_D1_CURR_X_COUNT() bfin_read16(MDMA_D1_CURR_X_COUNT)
+#define bfin_write_MDMA_D1_CURR_X_COUNT(val) bfin_write16(MDMA_D1_CURR_X_COUNT,val)
+#define bfin_read_MDMA_D1_CURR_Y_COUNT() bfin_read16(MDMA_D1_CURR_Y_COUNT)
+#define bfin_write_MDMA_D1_CURR_Y_COUNT(val) bfin_write16(MDMA_D1_CURR_Y_COUNT,val)
+#define bfin_read_MDMA_D1_IRQ_STATUS() bfin_read16(MDMA_D1_IRQ_STATUS)
+#define bfin_write_MDMA_D1_IRQ_STATUS(val) bfin_write16(MDMA_D1_IRQ_STATUS,val)
+#define bfin_read_MDMA_D1_PERIPHERAL_MAP() bfin_read16(MDMA_D1_PERIPHERAL_MAP)
+#define bfin_write_MDMA_D1_PERIPHERAL_MAP(val) bfin_write16(MDMA_D1_PERIPHERAL_MAP,val)
+
+#define bfin_read_MDMA_S1_CONFIG() bfin_read16(MDMA_S1_CONFIG)
+#define bfin_write_MDMA_S1_CONFIG(val) bfin_write16(MDMA_S1_CONFIG,val)
+#define bfin_read_MDMA_S1_NEXT_DESC_PTR() bfin_read32(MDMA_S1_NEXT_DESC_PTR)
+#define bfin_write_MDMA_S1_NEXT_DESC_PTR(val) bfin_write32(MDMA_S1_NEXT_DESC_PTR,val)
+#define bfin_read_MDMA_S1_START_ADDR() bfin_read32(MDMA_S1_START_ADDR)
+#define bfin_write_MDMA_S1_START_ADDR(val) bfin_write32(MDMA_S1_START_ADDR,val)
+#define bfin_read_MDMA_S1_X_COUNT() bfin_read16(MDMA_S1_X_COUNT)
+#define bfin_write_MDMA_S1_X_COUNT(val) bfin_write16(MDMA_S1_X_COUNT,val)
+#define bfin_read_MDMA_S1_Y_COUNT() bfin_read16(MDMA_S1_Y_COUNT)
+#define bfin_write_MDMA_S1_Y_COUNT(val) bfin_write16(MDMA_S1_Y_COUNT,val)
+#define bfin_read_MDMA_S1_X_MODIFY() bfin_read16(MDMA_S1_X_MODIFY)
+#define bfin_write_MDMA_S1_X_MODIFY(val) bfin_write16(MDMA_S1_X_MODIFY,val)
+#define bfin_read_MDMA_S1_Y_MODIFY() bfin_read16(MDMA_S1_Y_MODIFY)
+#define bfin_write_MDMA_S1_Y_MODIFY(val) bfin_write16(MDMA_S1_Y_MODIFY,val)
+#define bfin_read_MDMA_S1_CURR_DESC_PTR() bfin_read32(MDMA_S1_CURR_DESC_PTR)
+#define bfin_write_MDMA_S1_CURR_DESC_PTR(val) bfin_write32(MDMA_S1_CURR_DESC_PTR,val)
+#define bfin_read_MDMA_S1_CURR_ADDR() bfin_read32(MDMA_S1_CURR_ADDR)
+#define bfin_write_MDMA_S1_CURR_ADDR(val) bfin_write32(MDMA_S1_CURR_ADDR,val)
+#define bfin_read_MDMA_S1_CURR_X_COUNT() bfin_read16(MDMA_S1_CURR_X_COUNT)
+#define bfin_write_MDMA_S1_CURR_X_COUNT(val) bfin_write16(MDMA_S1_CURR_X_COUNT,val)
+#define bfin_read_MDMA_S1_CURR_Y_COUNT() bfin_read16(MDMA_S1_CURR_Y_COUNT)
+#define bfin_write_MDMA_S1_CURR_Y_COUNT(val) bfin_write16(MDMA_S1_CURR_Y_COUNT,val)
+#define bfin_read_MDMA_S1_IRQ_STATUS() bfin_read16(MDMA_S1_IRQ_STATUS)
+#define bfin_write_MDMA_S1_IRQ_STATUS(val) bfin_write16(MDMA_S1_IRQ_STATUS,val)
+#define bfin_read_MDMA_S1_PERIPHERAL_MAP() bfin_read16(MDMA_S1_PERIPHERAL_MAP)
+#define bfin_write_MDMA_S1_PERIPHERAL_MAP(val) bfin_write16(MDMA_S1_PERIPHERAL_MAP,val)
+
+#define bfin_read_MDMA_D0_CONFIG() bfin_read16(MDMA_D0_CONFIG)
+#define bfin_write_MDMA_D0_CONFIG(val) bfin_write16(MDMA_D0_CONFIG,val)
+#define bfin_read_MDMA_D0_NEXT_DESC_PTR() bfin_read32(MDMA_D0_NEXT_DESC_PTR)
+#define bfin_write_MDMA_D0_NEXT_DESC_PTR(val) bfin_write32(MDMA_D0_NEXT_DESC_PTR,val)
+#define bfin_read_MDMA_D0_START_ADDR() bfin_read32(MDMA_D0_START_ADDR)
+#define bfin_write_MDMA_D0_START_ADDR(val) bfin_write32(MDMA_D0_START_ADDR,val)
+#define bfin_read_MDMA_D0_X_COUNT() bfin_read16(MDMA_D0_X_COUNT)
+#define bfin_write_MDMA_D0_X_COUNT(val) bfin_write16(MDMA_D0_X_COUNT,val)
+#define bfin_read_MDMA_D0_Y_COUNT() bfin_read16(MDMA_D0_Y_COUNT)
+#define bfin_write_MDMA_D0_Y_COUNT(val) bfin_write16(MDMA_D0_Y_COUNT,val)
+#define bfin_read_MDMA_D0_X_MODIFY() bfin_read16(MDMA_D0_X_MODIFY)
+#define bfin_write_MDMA_D0_X_MODIFY(val) bfin_write16(MDMA_D0_X_MODIFY,val)
+#define bfin_read_MDMA_D0_Y_MODIFY() bfin_read16(MDMA_D0_Y_MODIFY)
+#define bfin_write_MDMA_D0_Y_MODIFY(val) bfin_write16(MDMA_D0_Y_MODIFY,val)
+#define bfin_read_MDMA_D0_CURR_DESC_PTR() bfin_read32(MDMA_D0_CURR_DESC_PTR)
+#define bfin_write_MDMA_D0_CURR_DESC_PTR(val) bfin_write32(MDMA_D0_CURR_DESC_PTR,val)
+#define bfin_read_MDMA_D0_CURR_ADDR() bfin_read32(MDMA_D0_CURR_ADDR)
+#define bfin_write_MDMA_D0_CURR_ADDR(val) bfin_write32(MDMA_D0_CURR_ADDR,val)
+#define bfin_read_MDMA_D0_CURR_X_COUNT() bfin_read16(MDMA_D0_CURR_X_COUNT)
+#define bfin_write_MDMA_D0_CURR_X_COUNT(val) bfin_write16(MDMA_D0_CURR_X_COUNT,val)
+#define bfin_read_MDMA_D0_CURR_Y_COUNT() bfin_read16(MDMA_D0_CURR_Y_COUNT)
+#define bfin_write_MDMA_D0_CURR_Y_COUNT(val) bfin_write16(MDMA_D0_CURR_Y_COUNT,val)
+#define bfin_read_MDMA_D0_IRQ_STATUS() bfin_read16(MDMA_D0_IRQ_STATUS)
+#define bfin_write_MDMA_D0_IRQ_STATUS(val) bfin_write16(MDMA_D0_IRQ_STATUS,val)
+#define bfin_read_MDMA_D0_PERIPHERAL_MAP() bfin_read16(MDMA_D0_PERIPHERAL_MAP)
+#define bfin_write_MDMA_D0_PERIPHERAL_MAP(val) bfin_write16(MDMA_D0_PERIPHERAL_MAP,val)
+
+#define bfin_read_MDMA_S0_CONFIG() bfin_read16(MDMA_S0_CONFIG)
+#define bfin_write_MDMA_S0_CONFIG(val) bfin_write16(MDMA_S0_CONFIG,val)
+#define bfin_read_MDMA_S0_NEXT_DESC_PTR() bfin_read32(MDMA_S0_NEXT_DESC_PTR)
+#define bfin_write_MDMA_S0_NEXT_DESC_PTR(val) bfin_write32(MDMA_S0_NEXT_DESC_PTR,val)
+#define bfin_read_MDMA_S0_START_ADDR() bfin_read32(MDMA_S0_START_ADDR)
+#define bfin_write_MDMA_S0_START_ADDR(val) bfin_write32(MDMA_S0_START_ADDR,val)
+#define bfin_read_MDMA_S0_X_COUNT() bfin_read16(MDMA_S0_X_COUNT)
+#define bfin_write_MDMA_S0_X_COUNT(val) bfin_write16(MDMA_S0_X_COUNT,val)
+#define bfin_read_MDMA_S0_Y_COUNT() bfin_read16(MDMA_S0_Y_COUNT)
+#define bfin_write_MDMA_S0_Y_COUNT(val) bfin_write16(MDMA_S0_Y_COUNT,val)
+#define bfin_read_MDMA_S0_X_MODIFY() bfin_read16(MDMA_S0_X_MODIFY)
+#define bfin_write_MDMA_S0_X_MODIFY(val) bfin_write16(MDMA_S0_X_MODIFY,val)
+#define bfin_read_MDMA_S0_Y_MODIFY() bfin_read16(MDMA_S0_Y_MODIFY)
+#define bfin_write_MDMA_S0_Y_MODIFY(val) bfin_write16(MDMA_S0_Y_MODIFY,val)
+#define bfin_read_MDMA_S0_CURR_DESC_PTR() bfin_read32(MDMA_S0_CURR_DESC_PTR)
+#define bfin_write_MDMA_S0_CURR_DESC_PTR(val) bfin_write32(MDMA_S0_CURR_DESC_PTR,val)
+#define bfin_read_MDMA_S0_CURR_ADDR() bfin_read32(MDMA_S0_CURR_ADDR)
+#define bfin_write_MDMA_S0_CURR_ADDR(val) bfin_write32(MDMA_S0_CURR_ADDR,val)
+#define bfin_read_MDMA_S0_CURR_X_COUNT() bfin_read16(MDMA_S0_CURR_X_COUNT)
+#define bfin_write_MDMA_S0_CURR_X_COUNT(val) bfin_write16(MDMA_S0_CURR_X_COUNT,val)
+#define bfin_read_MDMA_S0_CURR_Y_COUNT() bfin_read16(MDMA_S0_CURR_Y_COUNT)
+#define bfin_write_MDMA_S0_CURR_Y_COUNT(val) bfin_write16(MDMA_S0_CURR_Y_COUNT,val)
+#define bfin_read_MDMA_S0_IRQ_STATUS() bfin_read16(MDMA_S0_IRQ_STATUS)
+#define bfin_write_MDMA_S0_IRQ_STATUS(val) bfin_write16(MDMA_S0_IRQ_STATUS,val)
+#define bfin_read_MDMA_S0_PERIPHERAL_MAP() bfin_read16(MDMA_S0_PERIPHERAL_MAP)
+#define bfin_write_MDMA_S0_PERIPHERAL_MAP(val) bfin_write16(MDMA_S0_PERIPHERAL_MAP,val)
+
+/* Aysnchronous Memory Controller - External Bus Interface Unit (0xFFC0 3C00-0xFFC0 3FFF) */
+#define bfin_read_EBIU_AMGCTL() bfin_read16(EBIU_AMGCTL)
+#define bfin_write_EBIU_AMGCTL(val) bfin_write16(EBIU_AMGCTL,val)
+#define bfin_read_EBIU_AMBCTL0() bfin_read32(EBIU_AMBCTL0)
+#define bfin_write_EBIU_AMBCTL0(val) bfin_write32(EBIU_AMBCTL0,val)
+#define bfin_read_EBIU_AMBCTL1() bfin_read32(EBIU_AMBCTL1)
+#define bfin_write_EBIU_AMBCTL1(val) bfin_write32(EBIU_AMBCTL1,val)
+
+/* SDRAM Controller External Bus Interface Unit (0xFFC0 4C00-0xFFC0 4FFF) */
+#define bfin_read_EBIU_SDGCTL() bfin_read32(EBIU_SDGCTL)
+#define bfin_write_EBIU_SDGCTL(val) bfin_write32(EBIU_SDGCTL,val)
+#define bfin_read_EBIU_SDRRC() bfin_read16(EBIU_SDRRC)
+#define bfin_write_EBIU_SDRRC(val) bfin_write16(EBIU_SDRRC,val)
+#define bfin_read_EBIU_SDSTAT() bfin_read16(EBIU_SDSTAT)
+#define bfin_write_EBIU_SDSTAT(val) bfin_write16(EBIU_SDSTAT,val)
+#define bfin_read_EBIU_SDBCTL() bfin_read16(EBIU_SDBCTL)
+#define bfin_write_EBIU_SDBCTL(val) bfin_write16(EBIU_SDBCTL,val)
+
+/* UART Controller */
+#define bfin_read_UART_THR() bfin_read16(UART_THR)
+#define bfin_write_UART_THR(val) bfin_write16(UART_THR,val)
+#define bfin_read_UART_RBR() bfin_read16(UART_RBR)
+#define bfin_write_UART_RBR(val) bfin_write16(UART_RBR,val)
+#define bfin_read_UART_DLL() bfin_read16(UART_DLL)
+#define bfin_write_UART_DLL(val) bfin_write16(UART_DLL,val)
+#define bfin_read_UART_IER() bfin_read16(UART_IER)
+#define bfin_write_UART_IER(val) bfin_write16(UART_IER,val)
+#define bfin_read_UART_DLH() bfin_read16(UART_DLH)
+#define bfin_write_UART_DLH(val) bfin_write16(UART_DLH,val)
+#define bfin_read_UART_IIR() bfin_read16(UART_IIR)
+#define bfin_write_UART_IIR(val) bfin_write16(UART_IIR,val)
+#define bfin_read_UART_LCR() bfin_read16(UART_LCR)
+#define bfin_write_UART_LCR(val) bfin_write16(UART_LCR,val)
+#define bfin_read_UART_MCR() bfin_read16(UART_MCR)
+#define bfin_write_UART_MCR(val) bfin_write16(UART_MCR,val)
+#define bfin_read_UART_LSR() bfin_read16(UART_LSR)
+#define bfin_write_UART_LSR(val) bfin_write16(UART_LSR,val)
+/*
+#define UART_MSR
+*/
+#define bfin_read_UART_SCR() bfin_read16(UART_SCR)
+#define bfin_write_UART_SCR(val) bfin_write16(UART_SCR,val)
+#define bfin_read_UART_GCTL() bfin_read16(UART_GCTL)
+#define bfin_write_UART_GCTL(val) bfin_write16(UART_GCTL,val)
+
+/* SPI Controller */
+#define bfin_read_SPI_CTL() bfin_read16(SPI_CTL)
+#define bfin_write_SPI_CTL(val) bfin_write16(SPI_CTL,val)
+#define bfin_read_SPI_FLG() bfin_read16(SPI_FLG)
+#define bfin_write_SPI_FLG(val) bfin_write16(SPI_FLG,val)
+#define bfin_read_SPI_STAT() bfin_read16(SPI_STAT)
+#define bfin_write_SPI_STAT(val) bfin_write16(SPI_STAT,val)
+#define bfin_read_SPI_TDBR() bfin_read16(SPI_TDBR)
+#define bfin_write_SPI_TDBR(val) bfin_write16(SPI_TDBR,val)
+#define bfin_read_SPI_RDBR() bfin_read16(SPI_RDBR)
+#define bfin_write_SPI_RDBR(val) bfin_write16(SPI_RDBR,val)
+#define bfin_read_SPI_BAUD() bfin_read16(SPI_BAUD)
+#define bfin_write_SPI_BAUD(val) bfin_write16(SPI_BAUD,val)
+#define bfin_read_SPI_SHADOW() bfin_read16(SPI_SHADOW)
+#define bfin_write_SPI_SHADOW(val) bfin_write16(SPI_SHADOW,val)
+
+/* TIMER 0, 1, 2 Registers */
+#define bfin_read_TIMER0_CONFIG() bfin_read16(TIMER0_CONFIG)
+#define bfin_write_TIMER0_CONFIG(val) bfin_write16(TIMER0_CONFIG,val)
+#define bfin_read_TIMER0_COUNTER() bfin_read32(TIMER0_COUNTER)
+#define bfin_write_TIMER0_COUNTER(val) bfin_write32(TIMER0_COUNTER,val)
+#define bfin_read_TIMER0_PERIOD() bfin_read32(TIMER0_PERIOD)
+#define bfin_write_TIMER0_PERIOD(val) bfin_write32(TIMER0_PERIOD,val)
+#define bfin_read_TIMER0_WIDTH() bfin_read32(TIMER0_WIDTH)
+#define bfin_write_TIMER0_WIDTH(val) bfin_write32(TIMER0_WIDTH,val)
+
+#define bfin_read_TIMER1_CONFIG() bfin_read16(TIMER1_CONFIG)
+#define bfin_write_TIMER1_CONFIG(val) bfin_write16(TIMER1_CONFIG,val)
+#define bfin_read_TIMER1_COUNTER() bfin_read32(TIMER1_COUNTER)
+#define bfin_write_TIMER1_COUNTER(val) bfin_write32(TIMER1_COUNTER,val)
+#define bfin_read_TIMER1_PERIOD() bfin_read32(TIMER1_PERIOD)
+#define bfin_write_TIMER1_PERIOD(val) bfin_write32(TIMER1_PERIOD,val)
+#define bfin_read_TIMER1_WIDTH() bfin_read32(TIMER1_WIDTH)
+#define bfin_write_TIMER1_WIDTH(val) bfin_write32(TIMER1_WIDTH,val)
+
+#define bfin_read_TIMER2_CONFIG() bfin_read16(TIMER2_CONFIG)
+#define bfin_write_TIMER2_CONFIG(val) bfin_write16(TIMER2_CONFIG,val)
+#define bfin_read_TIMER2_COUNTER() bfin_read32(TIMER2_COUNTER)
+#define bfin_write_TIMER2_COUNTER(val) bfin_write32(TIMER2_COUNTER,val)
+#define bfin_read_TIMER2_PERIOD() bfin_read32(TIMER2_PERIOD)
+#define bfin_write_TIMER2_PERIOD(val) bfin_write32(TIMER2_PERIOD,val)
+#define bfin_read_TIMER2_WIDTH() bfin_read32(TIMER2_WIDTH)
+#define bfin_write_TIMER2_WIDTH(val) bfin_write32(TIMER2_WIDTH,val)
+
+#define bfin_read_TIMER_ENABLE() bfin_read16(TIMER_ENABLE)
+#define bfin_write_TIMER_ENABLE(val) bfin_write16(TIMER_ENABLE,val)
+#define bfin_read_TIMER_DISABLE() bfin_read16(TIMER_DISABLE)
+#define bfin_write_TIMER_DISABLE(val) bfin_write16(TIMER_DISABLE,val)
+#define bfin_read_TIMER_STATUS() bfin_read16(TIMER_STATUS)
+#define bfin_write_TIMER_STATUS(val) bfin_write16(TIMER_STATUS,val)
+
+/* SPORT0 Controller */
+#define bfin_read_SPORT0_TCR1() bfin_read16(SPORT0_TCR1)
+#define bfin_write_SPORT0_TCR1(val) bfin_write16(SPORT0_TCR1,val)
+#define bfin_read_SPORT0_TCR2() bfin_read16(SPORT0_TCR2)
+#define bfin_write_SPORT0_TCR2(val) bfin_write16(SPORT0_TCR2,val)
+#define bfin_read_SPORT0_TCLKDIV() bfin_read16(SPORT0_TCLKDIV)
+#define bfin_write_SPORT0_TCLKDIV(val) bfin_write16(SPORT0_TCLKDIV,val)
+#define bfin_read_SPORT0_TFSDIV() bfin_read16(SPORT0_TFSDIV)
+#define bfin_write_SPORT0_TFSDIV(val) bfin_write16(SPORT0_TFSDIV,val)
+#define bfin_read_SPORT0_TX() bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX(val) bfin_write32(SPORT0_TX,val)
+#define bfin_read_SPORT0_RX() bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX(val) bfin_write32(SPORT0_RX,val)
+#define bfin_read_SPORT0_TX32() bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX32(val) bfin_write32(SPORT0_TX,val)
+#define bfin_read_SPORT0_RX32() bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX32(val) bfin_write32(SPORT0_RX,val)
+#define bfin_read_SPORT0_TX16() bfin_read16(SPORT0_TX)
+#define bfin_write_SPORT0_TX16(val) bfin_write16(SPORT0_TX,val)
+#define bfin_read_SPORT0_RX16() bfin_read16(SPORT0_RX)
+#define bfin_write_SPORT0_RX16(val) bfin_write16(SPORT0_RX,val)
+#define bfin_read_SPORT0_RCR1() bfin_read16(SPORT0_RCR1)
+#define bfin_write_SPORT0_RCR1(val) bfin_write16(SPORT0_RCR1,val)
+#define bfin_read_SPORT0_RCR2() bfin_read16(SPORT0_RCR2)
+#define bfin_write_SPORT0_RCR2(val) bfin_write16(SPORT0_RCR2,val)
+#define bfin_read_SPORT0_RCLKDIV() bfin_read16(SPORT0_RCLKDIV)
+#define bfin_write_SPORT0_RCLKDIV(val) bfin_write16(SPORT0_RCLKDIV,val)
+#define bfin_read_SPORT0_RFSDIV() bfin_read16(SPORT0_RFSDIV)
+#define bfin_write_SPORT0_RFSDIV(val) bfin_write16(SPORT0_RFSDIV,val)
+#define bfin_read_SPORT0_STAT() bfin_read16(SPORT0_STAT)
+#define bfin_write_SPORT0_STAT(val) bfin_write16(SPORT0_STAT,val)
+#define bfin_read_SPORT0_CHNL() bfin_read16(SPORT0_CHNL)
+#define bfin_write_SPORT0_CHNL(val) bfin_write16(SPORT0_CHNL,val)
+#define bfin_read_SPORT0_MCMC1() bfin_read16(SPORT0_MCMC1)
+#define bfin_write_SPORT0_MCMC1(val) bfin_write16(SPORT0_MCMC1,val)
+#define bfin_read_SPORT0_MCMC2() bfin_read16(SPORT0_MCMC2)
+#define bfin_write_SPORT0_MCMC2(val) bfin_write16(SPORT0_MCMC2,val)
+#define bfin_read_SPORT0_MTCS0() bfin_read32(SPORT0_MTCS0)
+#define bfin_write_SPORT0_MTCS0(val) bfin_write32(SPORT0_MTCS0,val)
+#define bfin_read_SPORT0_MTCS1() bfin_read32(SPORT0_MTCS1)
+#define bfin_write_SPORT0_MTCS1(val) bfin_write32(SPORT0_MTCS1,val)
+#define bfin_read_SPORT0_MTCS2() bfin_read32(SPORT0_MTCS2)
+#define bfin_write_SPORT0_MTCS2(val) bfin_write32(SPORT0_MTCS2,val)
+#define bfin_read_SPORT0_MTCS3() bfin_read32(SPORT0_MTCS3)
+#define bfin_write_SPORT0_MTCS3(val) bfin_write32(SPORT0_MTCS3,val)
+#define bfin_read_SPORT0_MRCS0() bfin_read32(SPORT0_MRCS0)
+#define bfin_write_SPORT0_MRCS0(val) bfin_write32(SPORT0_MRCS0,val)
+#define bfin_read_SPORT0_MRCS1() bfin_read32(SPORT0_MRCS1)
+#define bfin_write_SPORT0_MRCS1(val) bfin_write32(SPORT0_MRCS1,val)
+#define bfin_read_SPORT0_MRCS2() bfin_read32(SPORT0_MRCS2)
+#define bfin_write_SPORT0_MRCS2(val) bfin_write32(SPORT0_MRCS2,val)
+#define bfin_read_SPORT0_MRCS3() bfin_read32(SPORT0_MRCS3)
+#define bfin_write_SPORT0_MRCS3(val) bfin_write32(SPORT0_MRCS3,val)
+
+/* SPORT1 Controller */
+#define bfin_read_SPORT1_TCR1() bfin_read16(SPORT1_TCR1)
+#define bfin_write_SPORT1_TCR1(val) bfin_write16(SPORT1_TCR1,val)
+#define bfin_read_SPORT1_TCR2() bfin_read16(SPORT1_TCR2)
+#define bfin_write_SPORT1_TCR2(val) bfin_write16(SPORT1_TCR2,val)
+#define bfin_read_SPORT1_TCLKDIV() bfin_read16(SPORT1_TCLKDIV)
+#define bfin_write_SPORT1_TCLKDIV(val) bfin_write16(SPORT1_TCLKDIV,val)
+#define bfin_read_SPORT1_TFSDIV() bfin_read16(SPORT1_TFSDIV)
+#define bfin_write_SPORT1_TFSDIV(val) bfin_write16(SPORT1_TFSDIV,val)
+#define bfin_read_SPORT1_TX() bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX(val) bfin_write32(SPORT1_TX,val)
+#define bfin_read_SPORT1_RX() bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX(val) bfin_write32(SPORT1_RX,val)
+#define bfin_read_SPORT1_TX32() bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX32(val) bfin_write32(SPORT1_TX,val)
+#define bfin_read_SPORT1_RX32() bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX32(val) bfin_write32(SPORT1_RX,val)
+#define bfin_read_SPORT1_TX16() bfin_read16(SPORT1_TX)
+#define bfin_write_SPORT1_TX16(val) bfin_write16(SPORT1_TX,val)
+#define bfin_read_SPORT1_RX16() bfin_read16(SPORT1_RX)
+#define bfin_write_SPORT1_RX16(val) bfin_write16(SPORT1_RX,val)
+#define bfin_read_SPORT1_RCR1() bfin_read16(SPORT1_RCR1)
+#define bfin_write_SPORT1_RCR1(val) bfin_write16(SPORT1_RCR1,val)
+#define bfin_read_SPORT1_RCR2() bfin_read16(SPORT1_RCR2)
+#define bfin_write_SPORT1_RCR2(val) bfin_write16(SPORT1_RCR2,val)
+#define bfin_read_SPORT1_RCLKDIV() bfin_read16(SPORT1_RCLKDIV)
+#define bfin_write_SPORT1_RCLKDIV(val) bfin_write16(SPORT1_RCLKDIV,val)
+#define bfin_read_SPORT1_RFSDIV() bfin_read16(SPORT1_RFSDIV)
+#define bfin_write_SPORT1_RFSDIV(val) bfin_write16(SPORT1_RFSDIV,val)
+#define bfin_read_SPORT1_STAT() bfin_read16(SPORT1_STAT)
+#define bfin_write_SPORT1_STAT(val) bfin_write16(SPORT1_STAT,val)
+#define bfin_read_SPORT1_CHNL() bfin_read16(SPORT1_CHNL)
+#define bfin_write_SPORT1_CHNL(val) bfin_write16(SPORT1_CHNL,val)
+#define bfin_read_SPORT1_MCMC1() bfin_read16(SPORT1_MCMC1)
+#define bfin_write_SPORT1_MCMC1(val) bfin_write16(SPORT1_MCMC1,val)
+#define bfin_read_SPORT1_MCMC2() bfin_read16(SPORT1_MCMC2)
+#define bfin_write_SPORT1_MCMC2(val) bfin_write16(SPORT1_MCMC2,val)
+#define bfin_read_SPORT1_MTCS0() bfin_read32(SPORT1_MTCS0)
+#define bfin_write_SPORT1_MTCS0(val) bfin_write32(SPORT1_MTCS0,val)
+#define bfin_read_SPORT1_MTCS1() bfin_read32(SPORT1_MTCS1)
+#define bfin_write_SPORT1_MTCS1(val) bfin_write32(SPORT1_MTCS1,val)
+#define bfin_read_SPORT1_MTCS2() bfin_read32(SPORT1_MTCS2)
+#define bfin_write_SPORT1_MTCS2(val) bfin_write32(SPORT1_MTCS2,val)
+#define bfin_read_SPORT1_MTCS3() bfin_read32(SPORT1_MTCS3)
+#define bfin_write_SPORT1_MTCS3(val) bfin_write32(SPORT1_MTCS3,val)
+#define bfin_read_SPORT1_MRCS0() bfin_read32(SPORT1_MRCS0)
+#define bfin_write_SPORT1_MRCS0(val) bfin_write32(SPORT1_MRCS0,val)
+#define bfin_read_SPORT1_MRCS1() bfin_read32(SPORT1_MRCS1)
+#define bfin_write_SPORT1_MRCS1(val) bfin_write32(SPORT1_MRCS1,val)
+#define bfin_read_SPORT1_MRCS2() bfin_read32(SPORT1_MRCS2)
+#define bfin_write_SPORT1_MRCS2(val) bfin_write32(SPORT1_MRCS2,val)
+#define bfin_read_SPORT1_MRCS3() bfin_read32(SPORT1_MRCS3)
+#define bfin_write_SPORT1_MRCS3(val) bfin_write32(SPORT1_MRCS3,val)
+
+/* Parallel Peripheral Interface (PPI) */
+#define bfin_read_PPI_CONTROL() bfin_read16(PPI_CONTROL)
+#define bfin_write_PPI_CONTROL(val) bfin_write16(PPI_CONTROL,val)
+#define bfin_read_PPI_STATUS() bfin_read16(PPI_STATUS)
+#define bfin_write_PPI_STATUS(val) bfin_write16(PPI_STATUS,val)
+#define bfin_clear_PPI_STATUS() bfin_read_PPI_STATUS()
+#define bfin_read_PPI_DELAY() bfin_read16(PPI_DELAY)
+#define bfin_write_PPI_DELAY(val) bfin_write16(PPI_DELAY,val)
+#define bfin_read_PPI_COUNT() bfin_read16(PPI_COUNT)
+#define bfin_write_PPI_COUNT(val) bfin_write16(PPI_COUNT,val)
+#define bfin_read_PPI_FRAME() bfin_read16(PPI_FRAME)
+#define bfin_write_PPI_FRAME(val) bfin_write16(PPI_FRAME,val)
+
+#endif /* _CDEF_BF532_H */
diff --git a/arch/blackfin/mach-bf533/include/mach/defBF532.h b/arch/blackfin/mach-bf533/include/mach/defBF532.h
new file mode 100644
index 0000000..7f46332
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/defBF532.h
@@ -0,0 +1,1266 @@
+/************************************************************************
+ *
+ * This file is subject to the terms and conditions of the GNU Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Non-GPL License also available as part of VisualDSP++
+ * http://www.analog.com/processors/resources/crosscore/visualDspDevSoftware.html
+ *
+ * (c) Copyright 2001-2005 Analog Devices, Inc. All rights reserved
+ *
+ * This file under source code control, please send bugs or changes to:
+ * dsptools.support@analog.com
+ *
+ ************************************************************************/
+/*
+ * File: include/asm-blackfin/mach-bf533/defBF532.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+/* SYSTEM & MM REGISTER BIT & ADDRESS DEFINITIONS FOR ADSP-BF532 */
+
+#ifndef _DEF_BF532_H
+#define _DEF_BF532_H
+
+/* include all Core registers and bit definitions */
+#include <asm/def_LPBlackfin.h>
+
+/*********************************************************************************** */
+/* System MMR Register Map */
+/*********************************************************************************** */
+/* Clock and System Control (0xFFC00000 - 0xFFC000FF) */
+
+#define PLL_CTL 0xFFC00000 /* PLL Control register (16-bit) */
+#define PLL_DIV 0xFFC00004 /* PLL Divide Register (16-bit) */
+#define VR_CTL 0xFFC00008 /* Voltage Regulator Control Register (16-bit) */
+#define PLL_STAT 0xFFC0000C /* PLL Status register (16-bit) */
+#define PLL_LOCKCNT 0xFFC00010 /* PLL Lock Count register (16-bit) */
+#define CHIPID 0xFFC00014 /* Chip ID Register */
+
+/* System Interrupt Controller (0xFFC00100 - 0xFFC001FF) */
+#define SWRST 0xFFC00100 /* Software Reset Register (16-bit) */
+#define SYSCR 0xFFC00104 /* System Configuration registe */
+#define SIC_RVECT 0xFFC00108 /* Interrupt Reset Vector Address Register */
+#define SIC_IMASK 0xFFC0010C /* Interrupt Mask Register */
+#define SIC_IAR0 0xFFC00110 /* Interrupt Assignment Register 0 */
+#define SIC_IAR1 0xFFC00114 /* Interrupt Assignment Register 1 */
+#define SIC_IAR2 0xFFC00118 /* Interrupt Assignment Register 2 */
+#define SIC_ISR 0xFFC00120 /* Interrupt Status Register */
+#define SIC_IWR 0xFFC00124 /* Interrupt Wakeup Register */
+
+/* Watchdog Timer (0xFFC00200 - 0xFFC002FF) */
+#define WDOG_CTL 0xFFC00200 /* Watchdog Control Register */
+#define WDOG_CNT 0xFFC00204 /* Watchdog Count Register */
+#define WDOG_STAT 0xFFC00208 /* Watchdog Status Register */
+
+/* Real Time Clock (0xFFC00300 - 0xFFC003FF) */
+#define RTC_STAT 0xFFC00300 /* RTC Status Register */
+#define RTC_ICTL 0xFFC00304 /* RTC Interrupt Control Register */
+#define RTC_ISTAT 0xFFC00308 /* RTC Interrupt Status Register */
+#define RTC_SWCNT 0xFFC0030C /* RTC Stopwatch Count Register */
+#define RTC_ALARM 0xFFC00310 /* RTC Alarm Time Register */
+#define RTC_FAST 0xFFC00314 /* RTC Prescaler Enable Register */
+#define RTC_PREN 0xFFC00314 /* RTC Prescaler Enable Register (alternate macro) */
+
+/* UART Controller (0xFFC00400 - 0xFFC004FF) */
+
+/*
+ * Because include/linux/serial_reg.h have defined UART_*,
+ * So we define blackfin uart regs to BFIN_UART_*.
+ */
+#define BFIN_UART_THR 0xFFC00400 /* Transmit Holding register */
+#define BFIN_UART_RBR 0xFFC00400 /* Receive Buffer register */
+#define BFIN_UART_DLL 0xFFC00400 /* Divisor Latch (Low-Byte) */
+#define BFIN_UART_IER 0xFFC00404 /* Interrupt Enable Register */
+#define BFIN_UART_DLH 0xFFC00404 /* Divisor Latch (High-Byte) */
+#define BFIN_UART_IIR 0xFFC00408 /* Interrupt Identification Register */
+#define BFIN_UART_LCR 0xFFC0040C /* Line Control Register */
+#define BFIN_UART_MCR 0xFFC00410 /* Modem Control Register */
+#define BFIN_UART_LSR 0xFFC00414 /* Line Status Register */
+#if 0
+#define BFIN_UART_MSR 0xFFC00418 /* Modem Status Register (UNUSED in ADSP-BF532) */
+#endif
+#define BFIN_UART_SCR 0xFFC0041C /* SCR Scratch Register */
+#define BFIN_UART_GCTL 0xFFC00424 /* Global Control Register */
+
+/* SPI Controller (0xFFC00500 - 0xFFC005FF) */
+#define SPI0_REGBASE 0xFFC00500
+#define SPI_CTL 0xFFC00500 /* SPI Control Register */
+#define SPI_FLG 0xFFC00504 /* SPI Flag register */
+#define SPI_STAT 0xFFC00508 /* SPI Status register */
+#define SPI_TDBR 0xFFC0050C /* SPI Transmit Data Buffer Register */
+#define SPI_RDBR 0xFFC00510 /* SPI Receive Data Buffer Register */
+#define SPI_BAUD 0xFFC00514 /* SPI Baud rate Register */
+#define SPI_SHADOW 0xFFC00518 /* SPI_RDBR Shadow Register */
+
+/* TIMER 0, 1, 2 Registers (0xFFC00600 - 0xFFC006FF) */
+
+#define TIMER0_CONFIG 0xFFC00600 /* Timer 0 Configuration Register */
+#define TIMER0_COUNTER 0xFFC00604 /* Timer 0 Counter Register */
+#define TIMER0_PERIOD 0xFFC00608 /* Timer 0 Period Register */
+#define TIMER0_WIDTH 0xFFC0060C /* Timer 0 Width Register */
+
+#define TIMER1_CONFIG 0xFFC00610 /* Timer 1 Configuration Register */
+#define TIMER1_COUNTER 0xFFC00614 /* Timer 1 Counter Register */
+#define TIMER1_PERIOD 0xFFC00618 /* Timer 1 Period Register */
+#define TIMER1_WIDTH 0xFFC0061C /* Timer 1 Width Register */
+
+#define TIMER2_CONFIG 0xFFC00620 /* Timer 2 Configuration Register */
+#define TIMER2_COUNTER 0xFFC00624 /* Timer 2 Counter Register */
+#define TIMER2_PERIOD 0xFFC00628 /* Timer 2 Period Register */
+#define TIMER2_WIDTH 0xFFC0062C /* Timer 2 Width Register */
+
+#define TIMER_ENABLE 0xFFC00640 /* Timer Enable Register */
+#define TIMER_DISABLE 0xFFC00644 /* Timer Disable Register */
+#define TIMER_STATUS 0xFFC00648 /* Timer Status Register */
+
+/* General Purpose IO (0xFFC00700 - 0xFFC007FF) */
+
+#define FIO_FLAG_D 0xFFC00700 /* Flag Mask to directly specify state of pins */
+#define FIO_FLAG_C 0xFFC00704 /* Peripheral Interrupt Flag Register (clear) */
+#define FIO_FLAG_S 0xFFC00708 /* Peripheral Interrupt Flag Register (set) */
+#define FIO_FLAG_T 0xFFC0070C /* Flag Mask to directly toggle state of pins */
+#define FIO_MASKA_D 0xFFC00710 /* Flag Mask Interrupt A Register (set directly) */
+#define FIO_MASKA_C 0xFFC00714 /* Flag Mask Interrupt A Register (clear) */
+#define FIO_MASKA_S 0xFFC00718 /* Flag Mask Interrupt A Register (set) */
+#define FIO_MASKA_T 0xFFC0071C /* Flag Mask Interrupt A Register (toggle) */
+#define FIO_MASKB_D 0xFFC00720 /* Flag Mask Interrupt B Register (set directly) */
+#define FIO_MASKB_C 0xFFC00724 /* Flag Mask Interrupt B Register (clear) */
+#define FIO_MASKB_S 0xFFC00728 /* Flag Mask Interrupt B Register (set) */
+#define FIO_MASKB_T 0xFFC0072C /* Flag Mask Interrupt B Register (toggle) */
+#define FIO_DIR 0xFFC00730 /* Peripheral Flag Direction Register */
+#define FIO_POLAR 0xFFC00734 /* Flag Source Polarity Register */
+#define FIO_EDGE 0xFFC00738 /* Flag Source Sensitivity Register */
+#define FIO_BOTH 0xFFC0073C /* Flag Set on BOTH Edges Register */
+#define FIO_INEN 0xFFC00740 /* Flag Input Enable Register */
+
+/* SPORT0 Controller (0xFFC00800 - 0xFFC008FF) */
+#define SPORT0_TCR1 0xFFC00800 /* SPORT0 Transmit Configuration 1 Register */
+#define SPORT0_TCR2 0xFFC00804 /* SPORT0 Transmit Configuration 2 Register */
+#define SPORT0_TCLKDIV 0xFFC00808 /* SPORT0 Transmit Clock Divider */
+#define SPORT0_TFSDIV 0xFFC0080C /* SPORT0 Transmit Frame Sync Divider */
+#define SPORT0_TX 0xFFC00810 /* SPORT0 TX Data Register */
+#define SPORT0_RX 0xFFC00818 /* SPORT0 RX Data Register */
+#define SPORT0_RCR1 0xFFC00820 /* SPORT0 Transmit Configuration 1 Register */
+#define SPORT0_RCR2 0xFFC00824 /* SPORT0 Transmit Configuration 2 Register */
+#define SPORT0_RCLKDIV 0xFFC00828 /* SPORT0 Receive Clock Divider */
+#define SPORT0_RFSDIV 0xFFC0082C /* SPORT0 Receive Frame Sync Divider */
+#define SPORT0_STAT 0xFFC00830 /* SPORT0 Status Register */
+#define SPORT0_CHNL 0xFFC00834 /* SPORT0 Current Channel Register */
+#define SPORT0_MCMC1 0xFFC00838 /* SPORT0 Multi-Channel Configuration Register 1 */
+#define SPORT0_MCMC2 0xFFC0083C /* SPORT0 Multi-Channel Configuration Register 2 */
+#define SPORT0_MTCS0 0xFFC00840 /* SPORT0 Multi-Channel Transmit Select Register 0 */
+#define SPORT0_MTCS1 0xFFC00844 /* SPORT0 Multi-Channel Transmit Select Register 1 */
+#define SPORT0_MTCS2 0xFFC00848 /* SPORT0 Multi-Channel Transmit Select Register 2 */
+#define SPORT0_MTCS3 0xFFC0084C /* SPORT0 Multi-Channel Transmit Select Register 3 */
+#define SPORT0_MRCS0 0xFFC00850 /* SPORT0 Multi-Channel Receive Select Register 0 */
+#define SPORT0_MRCS1 0xFFC00854 /* SPORT0 Multi-Channel Receive Select Register 1 */
+#define SPORT0_MRCS2 0xFFC00858 /* SPORT0 Multi-Channel Receive Select Register 2 */
+#define SPORT0_MRCS3 0xFFC0085C /* SPORT0 Multi-Channel Receive Select Register 3 */
+
+/* SPORT1 Controller (0xFFC00900 - 0xFFC009FF) */
+#define SPORT1_TCR1 0xFFC00900 /* SPORT1 Transmit Configuration 1 Register */
+#define SPORT1_TCR2 0xFFC00904 /* SPORT1 Transmit Configuration 2 Register */
+#define SPORT1_TCLKDIV 0xFFC00908 /* SPORT1 Transmit Clock Divider */
+#define SPORT1_TFSDIV 0xFFC0090C /* SPORT1 Transmit Frame Sync Divider */
+#define SPORT1_TX 0xFFC00910 /* SPORT1 TX Data Register */
+#define SPORT1_RX 0xFFC00918 /* SPORT1 RX Data Register */
+#define SPORT1_RCR1 0xFFC00920 /* SPORT1 Transmit Configuration 1 Register */
+#define SPORT1_RCR2 0xFFC00924 /* SPORT1 Transmit Configuration 2 Register */
+#define SPORT1_RCLKDIV 0xFFC00928 /* SPORT1 Receive Clock Divider */
+#define SPORT1_RFSDIV 0xFFC0092C /* SPORT1 Receive Frame Sync Divider */
+#define SPORT1_STAT 0xFFC00930 /* SPORT1 Status Register */
+#define SPORT1_CHNL 0xFFC00934 /* SPORT1 Current Channel Register */
+#define SPORT1_MCMC1 0xFFC00938 /* SPORT1 Multi-Channel Configuration Register 1 */
+#define SPORT1_MCMC2 0xFFC0093C /* SPORT1 Multi-Channel Configuration Register 2 */
+#define SPORT1_MTCS0 0xFFC00940 /* SPORT1 Multi-Channel Transmit Select Register 0 */
+#define SPORT1_MTCS1 0xFFC00944 /* SPORT1 Multi-Channel Transmit Select Register 1 */
+#define SPORT1_MTCS2 0xFFC00948 /* SPORT1 Multi-Channel Transmit Select Register 2 */
+#define SPORT1_MTCS3 0xFFC0094C /* SPORT1 Multi-Channel Transmit Select Register 3 */
+#define SPORT1_MRCS0 0xFFC00950 /* SPORT1 Multi-Channel Receive Select Register 0 */
+#define SPORT1_MRCS1 0xFFC00954 /* SPORT1 Multi-Channel Receive Select Register 1 */
+#define SPORT1_MRCS2 0xFFC00958 /* SPORT1 Multi-Channel Receive Select Register 2 */
+#define SPORT1_MRCS3 0xFFC0095C /* SPORT1 Multi-Channel Receive Select Register 3 */
+
+/* Asynchronous Memory Controller - External Bus Interface Unit */
+#define EBIU_AMGCTL 0xFFC00A00 /* Asynchronous Memory Global Control Register */
+#define EBIU_AMBCTL0 0xFFC00A04 /* Asynchronous Memory Bank Control Register 0 */
+#define EBIU_AMBCTL1 0xFFC00A08 /* Asynchronous Memory Bank Control Register 1 */
+
+/* SDRAM Controller External Bus Interface Unit (0xFFC00A00 - 0xFFC00AFF) */
+
+#define EBIU_SDGCTL 0xFFC00A10 /* SDRAM Global Control Register */
+#define EBIU_SDBCTL 0xFFC00A14 /* SDRAM Bank Control Register */
+#define EBIU_SDRRC 0xFFC00A18 /* SDRAM Refresh Rate Control Register */
+#define EBIU_SDSTAT 0xFFC00A1C /* SDRAM Status Register */
+
+/* DMA Traffic controls */
+#define DMA_TC_PER 0xFFC00B0C /* Traffic Control Periods Register */
+#define DMA_TC_CNT 0xFFC00B10 /* Traffic Control Current Counts Register */
+
+/* Alternate deprecated register names (below) provided for backwards code compatibility */
+#define DMA_TCPER 0xFFC00B0C /* Traffic Control Periods Register */
+#define DMA_TCCNT 0xFFC00B10 /* Traffic Control Current Counts Register */
+
+/* DMA Controller (0xFFC00C00 - 0xFFC00FFF) */
+#define DMA0_CONFIG 0xFFC00C08 /* DMA Channel 0 Configuration Register */
+#define DMA0_NEXT_DESC_PTR 0xFFC00C00 /* DMA Channel 0 Next Descriptor Pointer Register */
+#define DMA0_START_ADDR 0xFFC00C04 /* DMA Channel 0 Start Address Register */
+#define DMA0_X_COUNT 0xFFC00C10 /* DMA Channel 0 X Count Register */
+#define DMA0_Y_COUNT 0xFFC00C18 /* DMA Channel 0 Y Count Register */
+#define DMA0_X_MODIFY 0xFFC00C14 /* DMA Channel 0 X Modify Register */
+#define DMA0_Y_MODIFY 0xFFC00C1C /* DMA Channel 0 Y Modify Register */
+#define DMA0_CURR_DESC_PTR 0xFFC00C20 /* DMA Channel 0 Current Descriptor Pointer Register */
+#define DMA0_CURR_ADDR 0xFFC00C24 /* DMA Channel 0 Current Address Register */
+#define DMA0_CURR_X_COUNT 0xFFC00C30 /* DMA Channel 0 Current X Count Register */
+#define DMA0_CURR_Y_COUNT 0xFFC00C38 /* DMA Channel 0 Current Y Count Register */
+#define DMA0_IRQ_STATUS 0xFFC00C28 /* DMA Channel 0 Interrupt/Status Register */
+#define DMA0_PERIPHERAL_MAP 0xFFC00C2C /* DMA Channel 0 Peripheral Map Register */
+
+#define DMA1_CONFIG 0xFFC00C48 /* DMA Channel 1 Configuration Register */
+#define DMA1_NEXT_DESC_PTR 0xFFC00C40 /* DMA Channel 1 Next Descriptor Pointer Register */
+#define DMA1_START_ADDR 0xFFC00C44 /* DMA Channel 1 Start Address Register */
+#define DMA1_X_COUNT 0xFFC00C50 /* DMA Channel 1 X Count Register */
+#define DMA1_Y_COUNT 0xFFC00C58 /* DMA Channel 1 Y Count Register */
+#define DMA1_X_MODIFY 0xFFC00C54 /* DMA Channel 1 X Modify Register */
+#define DMA1_Y_MODIFY 0xFFC00C5C /* DMA Channel 1 Y Modify Register */
+#define DMA1_CURR_DESC_PTR 0xFFC00C60 /* DMA Channel 1 Current Descriptor Pointer Register */
+#define DMA1_CURR_ADDR 0xFFC00C64 /* DMA Channel 1 Current Address Register */
+#define DMA1_CURR_X_COUNT 0xFFC00C70 /* DMA Channel 1 Current X Count Register */
+#define DMA1_CURR_Y_COUNT 0xFFC00C78 /* DMA Channel 1 Current Y Count Register */
+#define DMA1_IRQ_STATUS 0xFFC00C68 /* DMA Channel 1 Interrupt/Status Register */
+#define DMA1_PERIPHERAL_MAP 0xFFC00C6C /* DMA Channel 1 Peripheral Map Register */
+
+#define DMA2_CONFIG 0xFFC00C88 /* DMA Channel 2 Configuration Register */
+#define DMA2_NEXT_DESC_PTR 0xFFC00C80 /* DMA Channel 2 Next Descriptor Pointer Register */
+#define DMA2_START_ADDR 0xFFC00C84 /* DMA Channel 2 Start Address Register */
+#define DMA2_X_COUNT 0xFFC00C90 /* DMA Channel 2 X Count Register */
+#define DMA2_Y_COUNT 0xFFC00C98 /* DMA Channel 2 Y Count Register */
+#define DMA2_X_MODIFY 0xFFC00C94 /* DMA Channel 2 X Modify Register */
+#define DMA2_Y_MODIFY 0xFFC00C9C /* DMA Channel 2 Y Modify Register */
+#define DMA2_CURR_DESC_PTR 0xFFC00CA0 /* DMA Channel 2 Current Descriptor Pointer Register */
+#define DMA2_CURR_ADDR 0xFFC00CA4 /* DMA Channel 2 Current Address Register */
+#define DMA2_CURR_X_COUNT 0xFFC00CB0 /* DMA Channel 2 Current X Count Register */
+#define DMA2_CURR_Y_COUNT 0xFFC00CB8 /* DMA Channel 2 Current Y Count Register */
+#define DMA2_IRQ_STATUS 0xFFC00CA8 /* DMA Channel 2 Interrupt/Status Register */
+#define DMA2_PERIPHERAL_MAP 0xFFC00CAC /* DMA Channel 2 Peripheral Map Register */
+
+#define DMA3_CONFIG 0xFFC00CC8 /* DMA Channel 3 Configuration Register */
+#define DMA3_NEXT_DESC_PTR 0xFFC00CC0 /* DMA Channel 3 Next Descriptor Pointer Register */
+#define DMA3_START_ADDR 0xFFC00CC4 /* DMA Channel 3 Start Address Register */
+#define DMA3_X_COUNT 0xFFC00CD0 /* DMA Channel 3 X Count Register */
+#define DMA3_Y_COUNT 0xFFC00CD8 /* DMA Channel 3 Y Count Register */
+#define DMA3_X_MODIFY 0xFFC00CD4 /* DMA Channel 3 X Modify Register */
+#define DMA3_Y_MODIFY 0xFFC00CDC /* DMA Channel 3 Y Modify Register */
+#define DMA3_CURR_DESC_PTR 0xFFC00CE0 /* DMA Channel 3 Current Descriptor Pointer Register */
+#define DMA3_CURR_ADDR 0xFFC00CE4 /* DMA Channel 3 Current Address Register */
+#define DMA3_CURR_X_COUNT 0xFFC00CF0 /* DMA Channel 3 Current X Count Register */
+#define DMA3_CURR_Y_COUNT 0xFFC00CF8 /* DMA Channel 3 Current Y Count Register */
+#define DMA3_IRQ_STATUS 0xFFC00CE8 /* DMA Channel 3 Interrupt/Status Register */
+#define DMA3_PERIPHERAL_MAP 0xFFC00CEC /* DMA Channel 3 Peripheral Map Register */
+
+#define DMA4_CONFIG 0xFFC00D08 /* DMA Channel 4 Configuration Register */
+#define DMA4_NEXT_DESC_PTR 0xFFC00D00 /* DMA Channel 4 Next Descriptor Pointer Register */
+#define DMA4_START_ADDR 0xFFC00D04 /* DMA Channel 4 Start Address Register */
+#define DMA4_X_COUNT 0xFFC00D10 /* DMA Channel 4 X Count Register */
+#define DMA4_Y_COUNT 0xFFC00D18 /* DMA Channel 4 Y Count Register */
+#define DMA4_X_MODIFY 0xFFC00D14 /* DMA Channel 4 X Modify Register */
+#define DMA4_Y_MODIFY 0xFFC00D1C /* DMA Channel 4 Y Modify Register */
+#define DMA4_CURR_DESC_PTR 0xFFC00D20 /* DMA Channel 4 Current Descriptor Pointer Register */
+#define DMA4_CURR_ADDR 0xFFC00D24 /* DMA Channel 4 Current Address Register */
+#define DMA4_CURR_X_COUNT 0xFFC00D30 /* DMA Channel 4 Current X Count Register */
+#define DMA4_CURR_Y_COUNT 0xFFC00D38 /* DMA Channel 4 Current Y Count Register */
+#define DMA4_IRQ_STATUS 0xFFC00D28 /* DMA Channel 4 Interrupt/Status Register */
+#define DMA4_PERIPHERAL_MAP 0xFFC00D2C /* DMA Channel 4 Peripheral Map Register */
+
+#define DMA5_CONFIG 0xFFC00D48 /* DMA Channel 5 Configuration Register */
+#define DMA5_NEXT_DESC_PTR 0xFFC00D40 /* DMA Channel 5 Next Descriptor Pointer Register */
+#define DMA5_START_ADDR 0xFFC00D44 /* DMA Channel 5 Start Address Register */
+#define DMA5_X_COUNT 0xFFC00D50 /* DMA Channel 5 X Count Register */
+#define DMA5_Y_COUNT 0xFFC00D58 /* DMA Channel 5 Y Count Register */
+#define DMA5_X_MODIFY 0xFFC00D54 /* DMA Channel 5 X Modify Register */
+#define DMA5_Y_MODIFY 0xFFC00D5C /* DMA Channel 5 Y Modify Register */
+#define DMA5_CURR_DESC_PTR 0xFFC00D60 /* DMA Channel 5 Current Descriptor Pointer Register */
+#define DMA5_CURR_ADDR 0xFFC00D64 /* DMA Channel 5 Current Address Register */
+#define DMA5_CURR_X_COUNT 0xFFC00D70 /* DMA Channel 5 Current X Count Register */
+#define DMA5_CURR_Y_COUNT 0xFFC00D78 /* DMA Channel 5 Current Y Count Register */
+#define DMA5_IRQ_STATUS 0xFFC00D68 /* DMA Channel 5 Interrupt/Status Register */
+#define DMA5_PERIPHERAL_MAP 0xFFC00D6C /* DMA Channel 5 Peripheral Map Register */
+
+#define DMA6_CONFIG 0xFFC00D88 /* DMA Channel 6 Configuration Register */
+#define DMA6_NEXT_DESC_PTR 0xFFC00D80 /* DMA Channel 6 Next Descriptor Pointer Register */
+#define DMA6_START_ADDR 0xFFC00D84 /* DMA Channel 6 Start Address Register */
+#define DMA6_X_COUNT 0xFFC00D90 /* DMA Channel 6 X Count Register */
+#define DMA6_Y_COUNT 0xFFC00D98 /* DMA Channel 6 Y Count Register */
+#define DMA6_X_MODIFY 0xFFC00D94 /* DMA Channel 6 X Modify Register */
+#define DMA6_Y_MODIFY 0xFFC00D9C /* DMA Channel 6 Y Modify Register */
+#define DMA6_CURR_DESC_PTR 0xFFC00DA0 /* DMA Channel 6 Current Descriptor Pointer Register */
+#define DMA6_CURR_ADDR 0xFFC00DA4 /* DMA Channel 6 Current Address Register */
+#define DMA6_CURR_X_COUNT 0xFFC00DB0 /* DMA Channel 6 Current X Count Register */
+#define DMA6_CURR_Y_COUNT 0xFFC00DB8 /* DMA Channel 6 Current Y Count Register */
+#define DMA6_IRQ_STATUS 0xFFC00DA8 /* DMA Channel 6 Interrupt/Status Register */
+#define DMA6_PERIPHERAL_MAP 0xFFC00DAC /* DMA Channel 6 Peripheral Map Register */
+
+#define DMA7_CONFIG 0xFFC00DC8 /* DMA Channel 7 Configuration Register */
+#define DMA7_NEXT_DESC_PTR 0xFFC00DC0 /* DMA Channel 7 Next Descriptor Pointer Register */
+#define DMA7_START_ADDR 0xFFC00DC4 /* DMA Channel 7 Start Address Register */
+#define DMA7_X_COUNT 0xFFC00DD0 /* DMA Channel 7 X Count Register */
+#define DMA7_Y_COUNT 0xFFC00DD8 /* DMA Channel 7 Y Count Register */
+#define DMA7_X_MODIFY 0xFFC00DD4 /* DMA Channel 7 X Modify Register */
+#define DMA7_Y_MODIFY 0xFFC00DDC /* DMA Channel 7 Y Modify Register */
+#define DMA7_CURR_DESC_PTR 0xFFC00DE0 /* DMA Channel 7 Current Descriptor Pointer Register */
+#define DMA7_CURR_ADDR 0xFFC00DE4 /* DMA Channel 7 Current Address Register */
+#define DMA7_CURR_X_COUNT 0xFFC00DF0 /* DMA Channel 7 Current X Count Register */
+#define DMA7_CURR_Y_COUNT 0xFFC00DF8 /* DMA Channel 7 Current Y Count Register */
+#define DMA7_IRQ_STATUS 0xFFC00DE8 /* DMA Channel 7 Interrupt/Status Register */
+#define DMA7_PERIPHERAL_MAP 0xFFC00DEC /* DMA Channel 7 Peripheral Map Register */
+
+#define MDMA_D1_CONFIG 0xFFC00E88 /* MemDMA Stream 1 Destination Configuration Register */
+#define MDMA_D1_NEXT_DESC_PTR 0xFFC00E80 /* MemDMA Stream 1 Destination Next Descriptor Pointer Register */
+#define MDMA_D1_START_ADDR 0xFFC00E84 /* MemDMA Stream 1 Destination Start Address Register */
+#define MDMA_D1_X_COUNT 0xFFC00E90 /* MemDMA Stream 1 Destination X Count Register */
+#define MDMA_D1_Y_COUNT 0xFFC00E98 /* MemDMA Stream 1 Destination Y Count Register */
+#define MDMA_D1_X_MODIFY 0xFFC00E94 /* MemDMA Stream 1 Destination X Modify Register */
+#define MDMA_D1_Y_MODIFY 0xFFC00E9C /* MemDMA Stream 1 Destination Y Modify Register */
+#define MDMA_D1_CURR_DESC_PTR 0xFFC00EA0 /* MemDMA Stream 1 Destination Current Descriptor Pointer Register */
+#define MDMA_D1_CURR_ADDR 0xFFC00EA4 /* MemDMA Stream 1 Destination Current Address Register */
+#define MDMA_D1_CURR_X_COUNT 0xFFC00EB0 /* MemDMA Stream 1 Destination Current X Count Register */
+#define MDMA_D1_CURR_Y_COUNT 0xFFC00EB8 /* MemDMA Stream 1 Destination Current Y Count Register */
+#define MDMA_D1_IRQ_STATUS 0xFFC00EA8 /* MemDMA Stream 1 Destination Interrupt/Status Register */
+#define MDMA_D1_PERIPHERAL_MAP 0xFFC00EAC /* MemDMA Stream 1 Destination Peripheral Map Register */
+
+#define MDMA_S1_CONFIG 0xFFC00EC8 /* MemDMA Stream 1 Source Configuration Register */
+#define MDMA_S1_NEXT_DESC_PTR 0xFFC00EC0 /* MemDMA Stream 1 Source Next Descriptor Pointer Register */
+#define MDMA_S1_START_ADDR 0xFFC00EC4 /* MemDMA Stream 1 Source Start Address Register */
+#define MDMA_S1_X_COUNT 0xFFC00ED0 /* MemDMA Stream 1 Source X Count Register */
+#define MDMA_S1_Y_COUNT 0xFFC00ED8 /* MemDMA Stream 1 Source Y Count Register */
+#define MDMA_S1_X_MODIFY 0xFFC00ED4 /* MemDMA Stream 1 Source X Modify Register */
+#define MDMA_S1_Y_MODIFY 0xFFC00EDC /* MemDMA Stream 1 Source Y Modify Register */
+#define MDMA_S1_CURR_DESC_PTR 0xFFC00EE0 /* MemDMA Stream 1 Source Current Descriptor Pointer Register */
+#define MDMA_S1_CURR_ADDR 0xFFC00EE4 /* MemDMA Stream 1 Source Current Address Register */
+#define MDMA_S1_CURR_X_COUNT 0xFFC00EF0 /* MemDMA Stream 1 Source Current X Count Register */
+#define MDMA_S1_CURR_Y_COUNT 0xFFC00EF8 /* MemDMA Stream 1 Source Current Y Count Register */
+#define MDMA_S1_IRQ_STATUS 0xFFC00EE8 /* MemDMA Stream 1 Source Interrupt/Status Register */
+#define MDMA_S1_PERIPHERAL_MAP 0xFFC00EEC /* MemDMA Stream 1 Source Peripheral Map Register */
+
+#define MDMA_D0_CONFIG 0xFFC00E08 /* MemDMA Stream 0 Destination Configuration Register */
+#define MDMA_D0_NEXT_DESC_PTR 0xFFC00E00 /* MemDMA Stream 0 Destination Next Descriptor Pointer Register */
+#define MDMA_D0_START_ADDR 0xFFC00E04 /* MemDMA Stream 0 Destination Start Address Register */
+#define MDMA_D0_X_COUNT 0xFFC00E10 /* MemDMA Stream 0 Destination X Count Register */
+#define MDMA_D0_Y_COUNT 0xFFC00E18 /* MemDMA Stream 0 Destination Y Count Register */
+#define MDMA_D0_X_MODIFY 0xFFC00E14 /* MemDMA Stream 0 Destination X Modify Register */
+#define MDMA_D0_Y_MODIFY 0xFFC00E1C /* MemDMA Stream 0 Destination Y Modify Register */
+#define MDMA_D0_CURR_DESC_PTR 0xFFC00E20 /* MemDMA Stream 0 Destination Current Descriptor Pointer Register */
+#define MDMA_D0_CURR_ADDR 0xFFC00E24 /* MemDMA Stream 0 Destination Current Address Register */
+#define MDMA_D0_CURR_X_COUNT 0xFFC00E30 /* MemDMA Stream 0 Destination Current X Count Register */
+#define MDMA_D0_CURR_Y_COUNT 0xFFC00E38 /* MemDMA Stream 0 Destination Current Y Count Register */
+#define MDMA_D0_IRQ_STATUS 0xFFC00E28 /* MemDMA Stream 0 Destination Interrupt/Status Register */
+#define MDMA_D0_PERIPHERAL_MAP 0xFFC00E2C /* MemDMA Stream 0 Destination Peripheral Map Register */
+
+#define MDMA_S0_CONFIG 0xFFC00E48 /* MemDMA Stream 0 Source Configuration Register */
+#define MDMA_S0_NEXT_DESC_PTR 0xFFC00E40 /* MemDMA Stream 0 Source Next Descriptor Pointer Register */
+#define MDMA_S0_START_ADDR 0xFFC00E44 /* MemDMA Stream 0 Source Start Address Register */
+#define MDMA_S0_X_COUNT 0xFFC00E50 /* MemDMA Stream 0 Source X Count Register */
+#define MDMA_S0_Y_COUNT 0xFFC00E58 /* MemDMA Stream 0 Source Y Count Register */
+#define MDMA_S0_X_MODIFY 0xFFC00E54 /* MemDMA Stream 0 Source X Modify Register */
+#define MDMA_S0_Y_MODIFY 0xFFC00E5C /* MemDMA Stream 0 Source Y Modify Register */
+#define MDMA_S0_CURR_DESC_PTR 0xFFC00E60 /* MemDMA Stream 0 Source Current Descriptor Pointer Register */
+#define MDMA_S0_CURR_ADDR 0xFFC00E64 /* MemDMA Stream 0 Source Current Address Register */
+#define MDMA_S0_CURR_X_COUNT 0xFFC00E70 /* MemDMA Stream 0 Source Current X Count Register */
+#define MDMA_S0_CURR_Y_COUNT 0xFFC00E78 /* MemDMA Stream 0 Source Current Y Count Register */
+#define MDMA_S0_IRQ_STATUS 0xFFC00E68 /* MemDMA Stream 0 Source Interrupt/Status Register */
+#define MDMA_S0_PERIPHERAL_MAP 0xFFC00E6C /* MemDMA Stream 0 Source Peripheral Map Register */
+
+/* Parallel Peripheral Interface (PPI) (0xFFC01000 - 0xFFC010FF) */
+
+#define PPI_CONTROL 0xFFC01000 /* PPI Control Register */
+#define PPI_STATUS 0xFFC01004 /* PPI Status Register */
+#define PPI_COUNT 0xFFC01008 /* PPI Transfer Count Register */
+#define PPI_DELAY 0xFFC0100C /* PPI Delay Count Register */
+#define PPI_FRAME 0xFFC01010 /* PPI Frame Length Register */
+
+/*********************************************************************************** */
+/* System MMR Register Bits */
+/******************************************************************************* */
+
+/* ********************* PLL AND RESET MASKS ************************ */
+
+/* PLL_CTL Masks */
+#define PLL_CLKIN 0x0000 /* Pass CLKIN to PLL */
+#define PLL_CLKIN_DIV2 0x0001 /* Pass CLKIN/2 to PLL */
+#define DF 0x0001 /* 0: PLL = CLKIN, 1: PLL = CLKIN/2 */
+#define PLL_OFF 0x0002 /* Shut off PLL clocks */
+#define STOPCK_OFF 0x0008 /* Core clock off */
+#define STOPCK 0x0008 /* Core Clock Off */
+#define PDWN 0x0020 /* Put the PLL in a Deep Sleep state */
+#if !defined(__ADSPBF538__)
+/* this file is included in defBF538.h but IN_DELAY/OUT_DELAY are different */
+# define IN_DELAY 0x0040 /* Add 200ps Delay To EBIU Input Latches */
+# define OUT_DELAY 0x0080 /* Add 200ps Delay To EBIU Output Signals */
+#endif
+#define BYPASS 0x0100 /* Bypass the PLL */
+/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits) */
+#define SET_MSEL(x) (((x)&0x3F) << 0x9) /* Set MSEL = 0-63 --> VCO = CLKIN*MSEL */
+
+/* PLL_DIV Masks */
+#define SSEL 0x000F /* System Select */
+#define CSEL 0x0030 /* Core Select */
+
+#define SCLK_DIV(x) (x) /* SCLK = VCO / x */
+
+#define CCLK_DIV1 0x00000000 /* CCLK = VCO / 1 */
+#define CCLK_DIV2 0x00000010 /* CCLK = VCO / 2 */
+#define CCLK_DIV4 0x00000020 /* CCLK = VCO / 4 */
+#define CCLK_DIV8 0x00000030 /* CCLK = VCO / 8 */
+/* PLL_DIV Macros */
+#define SET_SSEL(x) ((x)&0xF) /* Set SSEL = 0-15 --> SCLK = VCO/SSEL */
+
+/* PLL_STAT Masks */
+#define ACTIVE_PLLENABLED 0x0001 /* Processor In Active Mode With PLL Enabled */
+#define FULL_ON 0x0002 /* Processor In Full On Mode */
+#define ACTIVE_PLLDISABLED 0x0004 /* Processor In Active Mode With PLL Disabled */
+#define PLL_LOCKED 0x0020 /* PLL_LOCKCNT Has Been Reached */
+
+/* VR_CTL Masks */
+#define FREQ 0x0003 /* Switching Oscillator Frequency For Regulator */
+#define HIBERNATE 0x0000 /* Powerdown/Bypass On-Board Regulation */
+#define FREQ_333 0x0001 /* Switching Frequency Is 333 kHz */
+#define FREQ_667 0x0002 /* Switching Frequency Is 667 kHz */
+#define FREQ_1000 0x0003 /* Switching Frequency Is 1 MHz */
+
+#define GAIN 0x000C /* Voltage Level Gain */
+#define GAIN_5 0x0000 /* GAIN = 5 */
+#define GAIN_10 0x0004 /* GAIN = 10 */
+#define GAIN_20 0x0008 /* GAIN = 20 */
+#define GAIN_50 0x000C /* GAIN = 50 */
+
+#define VLEV 0x00F0 /* Internal Voltage Level */
+#define VLEV_085 0x0060 /* VLEV = 0.85 V (-5% - +10% Accuracy) */
+#define VLEV_090 0x0070 /* VLEV = 0.90 V (-5% - +10% Accuracy) */
+#define VLEV_095 0x0080 /* VLEV = 0.95 V (-5% - +10% Accuracy) */
+#define VLEV_100 0x0090 /* VLEV = 1.00 V (-5% - +10% Accuracy) */
+#define VLEV_105 0x00A0 /* VLEV = 1.05 V (-5% - +10% Accuracy) */
+#define VLEV_110 0x00B0 /* VLEV = 1.10 V (-5% - +10% Accuracy) */
+#define VLEV_115 0x00C0 /* VLEV = 1.15 V (-5% - +10% Accuracy) */
+#define VLEV_120 0x00D0 /* VLEV = 1.20 V (-5% - +10% Accuracy) */
+#define VLEV_125 0x00E0 /* VLEV = 1.25 V (-5% - +10% Accuracy) */
+#define VLEV_130 0x00F0 /* VLEV = 1.30 V (-5% - +10% Accuracy) */
+
+#define WAKE 0x0100 /* Enable RTC/Reset Wakeup From Hibernate */
+#define SCKELOW 0x8000 /* Do Not Drive SCKE High During Reset After Hibernate */
+
+/* CHIPID Masks */
+#define CHIPID_VERSION 0xF0000000
+#define CHIPID_FAMILY 0x0FFFF000
+#define CHIPID_MANUFACTURE 0x00000FFE
+
+/* SWRST Mask */
+#define SYSTEM_RESET 0x0007 /* Initiates A System Software Reset */
+#define DOUBLE_FAULT 0x0008 /* Core Double Fault Causes Reset */
+#define RESET_DOUBLE 0x2000 /* SW Reset Generated By Core Double-Fault */
+#define RESET_WDOG 0x4000 /* SW Reset Generated By Watchdog Timer */
+#define RESET_SOFTWARE 0x8000 /* SW Reset Occurred Since Last Read Of SWRST */
+
+/* SYSCR Masks */
+#define BMODE 0x0006 /* Boot Mode - Latched During HW Reset From Mode Pins */
+#define NOBOOT 0x0010 /* Execute From L1 or ASYNC Bank 0 When BMODE = 0 */
+
+/* ************* SYSTEM INTERRUPT CONTROLLER MASKS ***************** */
+
+ /* SIC_IAR0 Masks */
+
+#define P0_IVG(x) ((x)-7) /* Peripheral #0 assigned IVG #x */
+#define P1_IVG(x) ((x)-7) << 0x4 /* Peripheral #1 assigned IVG #x */
+#define P2_IVG(x) ((x)-7) << 0x8 /* Peripheral #2 assigned IVG #x */
+#define P3_IVG(x) ((x)-7) << 0xC /* Peripheral #3 assigned IVG #x */
+#define P4_IVG(x) ((x)-7) << 0x10 /* Peripheral #4 assigned IVG #x */
+#define P5_IVG(x) ((x)-7) << 0x14 /* Peripheral #5 assigned IVG #x */
+#define P6_IVG(x) ((x)-7) << 0x18 /* Peripheral #6 assigned IVG #x */
+#define P7_IVG(x) ((x)-7) << 0x1C /* Peripheral #7 assigned IVG #x */
+
+/* SIC_IAR1 Masks */
+
+#define P8_IVG(x) ((x)-7) /* Peripheral #8 assigned IVG #x */
+#define P9_IVG(x) ((x)-7) << 0x4 /* Peripheral #9 assigned IVG #x */
+#define P10_IVG(x) ((x)-7) << 0x8 /* Peripheral #10 assigned IVG #x */
+#define P11_IVG(x) ((x)-7) << 0xC /* Peripheral #11 assigned IVG #x */
+#define P12_IVG(x) ((x)-7) << 0x10 /* Peripheral #12 assigned IVG #x */
+#define P13_IVG(x) ((x)-7) << 0x14 /* Peripheral #13 assigned IVG #x */
+#define P14_IVG(x) ((x)-7) << 0x18 /* Peripheral #14 assigned IVG #x */
+#define P15_IVG(x) ((x)-7) << 0x1C /* Peripheral #15 assigned IVG #x */
+
+/* SIC_IAR2 Masks */
+#define P16_IVG(x) ((x)-7) /* Peripheral #16 assigned IVG #x */
+#define P17_IVG(x) ((x)-7) << 0x4 /* Peripheral #17 assigned IVG #x */
+#define P18_IVG(x) ((x)-7) << 0x8 /* Peripheral #18 assigned IVG #x */
+#define P19_IVG(x) ((x)-7) << 0xC /* Peripheral #19 assigned IVG #x */
+#define P20_IVG(x) ((x)-7) << 0x10 /* Peripheral #20 assigned IVG #x */
+#define P21_IVG(x) ((x)-7) << 0x14 /* Peripheral #21 assigned IVG #x */
+#define P22_IVG(x) ((x)-7) << 0x18 /* Peripheral #22 assigned IVG #x */
+#define P23_IVG(x) ((x)-7) << 0x1C /* Peripheral #23 assigned IVG #x */
+
+/* SIC_IMASK Masks */
+#define SIC_UNMASK_ALL 0x00000000 /* Unmask all peripheral interrupts */
+#define SIC_MASK_ALL 0xFFFFFFFF /* Mask all peripheral interrupts */
+#define SIC_MASK(x) (1 << (x)) /* Mask Peripheral #x interrupt */
+#define SIC_UNMASK(x) (0xFFFFFFFF ^ (1 << (x))) /* Unmask Peripheral #x interrupt */
+
+/* SIC_IWR Masks */
+#define IWR_DISABLE_ALL 0x00000000 /* Wakeup Disable all peripherals */
+#define IWR_ENABLE_ALL 0xFFFFFFFF /* Wakeup Enable all peripherals */
+#define IWR_ENABLE(x) (1 << (x)) /* Wakeup Enable Peripheral #x */
+#define IWR_DISABLE(x) (0xFFFFFFFF ^ (1 << (x))) /* Wakeup Disable Peripheral #x */
+
+/* ***************************** UART CONTROLLER MASKS ********************** */
+
+/* UART_LCR Register */
+
+#define DLAB 0x80
+#define SB 0x40
+#define STP 0x20
+#define EPS 0x10
+#define PEN 0x08
+#define STB 0x04
+#define WLS(x) ((x-5) & 0x03)
+
+#define DLAB_P 0x07
+#define SB_P 0x06
+#define STP_P 0x05
+#define EPS_P 0x04
+#define PEN_P 0x03
+#define STB_P 0x02
+#define WLS_P1 0x01
+#define WLS_P0 0x00
+
+/* UART_MCR Register */
+#define LOOP_ENA 0x10
+#define LOOP_ENA_P 0x04
+
+/* UART_LSR Register */
+#define TEMT 0x40
+#define THRE 0x20
+#define BI 0x10
+#define FE 0x08
+#define PE 0x04
+#define OE 0x02
+#define DR 0x01
+
+#define TEMP_P 0x06
+#define THRE_P 0x05
+#define BI_P 0x04
+#define FE_P 0x03
+#define PE_P 0x02
+#define OE_P 0x01
+#define DR_P 0x00
+
+/* UART_IER Register */
+#define ELSI 0x04
+#define ETBEI 0x02
+#define ERBFI 0x01
+
+#define ELSI_P 0x02
+#define ETBEI_P 0x01
+#define ERBFI_P 0x00
+
+/* UART_IIR Register */
+#define STATUS(x) ((x << 1) & 0x06)
+#define NINT 0x01
+#define STATUS_P1 0x02
+#define STATUS_P0 0x01
+#define NINT_P 0x00
+#define IIR_TX_READY 0x02 /* UART_THR empty */
+#define IIR_RX_READY 0x04 /* Receive data ready */
+#define IIR_LINE_CHANGE 0x06 /* Receive line status */
+#define IIR_STATUS 0x06
+
+/* UART_GCTL Register */
+#define FFE 0x20
+#define FPE 0x10
+#define RPOLC 0x08
+#define TPOLC 0x04
+#define IREN 0x02
+#define UCEN 0x01
+
+#define FFE_P 0x05
+#define FPE_P 0x04
+#define RPOLC_P 0x03
+#define TPOLC_P 0x02
+#define IREN_P 0x01
+#define UCEN_P 0x00
+
+/* ********** SERIAL PORT MASKS ********************** */
+
+/* SPORTx_TCR1 Masks */
+#define TSPEN 0x0001 /* TX enable */
+#define ITCLK 0x0002 /* Internal TX Clock Select */
+#define TDTYPE 0x000C /* TX Data Formatting Select */
+#define DTYPE_NORM 0x0000 /* Data Format Normal */
+#define DTYPE_ULAW 0x0008 /* Compand Using u-Law */
+#define DTYPE_ALAW 0x000C /* Compand Using A-Law */
+#define TLSBIT 0x0010 /* TX Bit Order */
+#define ITFS 0x0200 /* Internal TX Frame Sync Select */
+#define TFSR 0x0400 /* TX Frame Sync Required Select */
+#define DITFS 0x0800 /* Data Independent TX Frame Sync Select */
+#define LTFS 0x1000 /* Low TX Frame Sync Select */
+#define LATFS 0x2000 /* Late TX Frame Sync Select */
+#define TCKFE 0x4000 /* TX Clock Falling Edge Select */
+
+/* SPORTx_TCR2 Masks */
+#if defined(__ADSPBF531__) || defined(__ADSPBF532__) || \
+ defined(__ADSPBF533__)
+# define SLEN 0x001F /*TX Word Length */
+#else
+# define SLEN(x) ((x)&0x1F) /* SPORT TX Word Length (2 - 31) */
+#endif
+#define TXSE 0x0100 /*TX Secondary Enable */
+#define TSFSE 0x0200 /*TX Stereo Frame Sync Enable */
+#define TRFST 0x0400 /*TX Right-First Data Order */
+
+/* SPORTx_RCR1 Masks */
+#define RSPEN 0x0001 /* RX enable */
+#define IRCLK 0x0002 /* Internal RX Clock Select */
+#define RDTYPE 0x000C /* RX Data Formatting Select */
+#define DTYPE_NORM 0x0000 /* no companding */
+#define DTYPE_ULAW 0x0008 /* Compand Using u-Law */
+#define DTYPE_ALAW 0x000C /* Compand Using A-Law */
+#define RLSBIT 0x0010 /* RX Bit Order */
+#define IRFS 0x0200 /* Internal RX Frame Sync Select */
+#define RFSR 0x0400 /* RX Frame Sync Required Select */
+#define LRFS 0x1000 /* Low RX Frame Sync Select */
+#define LARFS 0x2000 /* Late RX Frame Sync Select */
+#define RCKFE 0x4000 /* RX Clock Falling Edge Select */
+
+/* SPORTx_RCR2 Masks */
+/* SLEN defined above */
+#define RXSE 0x0100 /*RX Secondary Enable */
+#define RSFSE 0x0200 /*RX Stereo Frame Sync Enable */
+#define RRFST 0x0400 /*Right-First Data Order */
+
+/*SPORTx_STAT Masks */
+#define RXNE 0x0001 /*RX FIFO Not Empty Status */
+#define RUVF 0x0002 /*RX Underflow Status */
+#define ROVF 0x0004 /*RX Overflow Status */
+#define TXF 0x0008 /*TX FIFO Full Status */
+#define TUVF 0x0010 /*TX Underflow Status */
+#define TOVF 0x0020 /*TX Overflow Status */
+#define TXHRE 0x0040 /*TX Hold Register Empty */
+
+/*SPORTx_MCMC1 Masks */
+#define SP_WSIZE 0x0000F000 /*Multichannel Window Size Field */
+#define SP_WOFF 0x000003FF /*Multichannel Window Offset Field */
+/* SPORTx_MCMC1 Macros */
+#define SET_SP_WOFF(x) ((x) & 0x3FF) /* Multichannel Window Offset Field */
+/* Only use SET_WSIZE Macro With Logic OR While Setting Lower Order Bits */
+#define SET_SP_WSIZE(x) (((((x)>>0x3)-1)&0xF) << 0xC) /* Multichannel Window Size = (x/8)-1 */
+
+/*SPORTx_MCMC2 Masks */
+#define MCCRM 0x00000003 /*Multichannel Clock Recovery Mode */
+#define REC_BYPASS 0x0000 /* Bypass Mode (No Clock Recovery) */
+#define REC_2FROM4 0x0002 /* Recover 2 MHz Clock from 4 MHz Clock */
+#define REC_8FROM16 0x0003 /* Recover 8 MHz Clock from 16 MHz Clock */
+#define MCDTXPE 0x00000004 /*Multichannel DMA Transmit Packing */
+#define MCDRXPE 0x00000008 /*Multichannel DMA Receive Packing */
+#define MCMEN 0x00000010 /*Multichannel Frame Mode Enable */
+#define FSDR 0x00000080 /*Multichannel Frame Sync to Data Relationship */
+#define MFD 0x0000F000 /*Multichannel Frame Delay */
+#define MFD_0 0x0000 /* Multichannel Frame Delay = 0 */
+#define MFD_1 0x1000 /* Multichannel Frame Delay = 1 */
+#define MFD_2 0x2000 /* Multichannel Frame Delay = 2 */
+#define MFD_3 0x3000 /* Multichannel Frame Delay = 3 */
+#define MFD_4 0x4000 /* Multichannel Frame Delay = 4 */
+#define MFD_5 0x5000 /* Multichannel Frame Delay = 5 */
+#define MFD_6 0x6000 /* Multichannel Frame Delay = 6 */
+#define MFD_7 0x7000 /* Multichannel Frame Delay = 7 */
+#define MFD_8 0x8000 /* Multichannel Frame Delay = 8 */
+#define MFD_9 0x9000 /* Multichannel Frame Delay = 9 */
+#define MFD_10 0xA000 /* Multichannel Frame Delay = 10 */
+#define MFD_11 0xB000 /* Multichannel Frame Delay = 11 */
+#define MFD_12 0xC000 /* Multichannel Frame Delay = 12 */
+#define MFD_13 0xD000 /* Multichannel Frame Delay = 13 */
+#define MFD_14 0xE000 /* Multichannel Frame Delay = 14 */
+#define MFD_15 0xF000 /* Multichannel Frame Delay = 15 */
+
+/* ********* PARALLEL PERIPHERAL INTERFACE (PPI) MASKS **************** */
+
+/* PPI_CONTROL Masks */
+#define PORT_EN 0x00000001 /* PPI Port Enable */
+#define PORT_DIR 0x00000002 /* PPI Port Direction */
+#define XFR_TYPE 0x0000000C /* PPI Transfer Type */
+#define PORT_CFG 0x00000030 /* PPI Port Configuration */
+#define FLD_SEL 0x00000040 /* PPI Active Field Select */
+#define PACK_EN 0x00000080 /* PPI Packing Mode */
+#define DMA32 0x00000100 /* PPI 32-bit DMA Enable */
+#define SKIP_EN 0x00000200 /* PPI Skip Element Enable */
+#define SKIP_EO 0x00000400 /* PPI Skip Even/Odd Elements */
+#define DLENGTH 0x00003800 /* PPI Data Length */
+#define DLEN_8 0x0000 /* Data Length = 8 Bits */
+#define DLEN_10 0x0800 /* Data Length = 10 Bits */
+#define DLEN_11 0x1000 /* Data Length = 11 Bits */
+#define DLEN_12 0x1800 /* Data Length = 12 Bits */
+#define DLEN_13 0x2000 /* Data Length = 13 Bits */
+#define DLEN_14 0x2800 /* Data Length = 14 Bits */
+#define DLEN_15 0x3000 /* Data Length = 15 Bits */
+#define DLEN_16 0x3800 /* Data Length = 16 Bits */
+#define DLEN(x) (((x-9) & 0x07) << 11) /* PPI Data Length (only works for x=10-->x=16) */
+#define POL 0x0000C000 /* PPI Signal Polarities */
+#define POLC 0x4000 /* PPI Clock Polarity */
+#define POLS 0x8000 /* PPI Frame Sync Polarity */
+
+/* PPI_STATUS Masks */
+#define FLD 0x00000400 /* Field Indicator */
+#define FT_ERR 0x00000800 /* Frame Track Error */
+#define OVR 0x00001000 /* FIFO Overflow Error */
+#define UNDR 0x00002000 /* FIFO Underrun Error */
+#define ERR_DET 0x00004000 /* Error Detected Indicator */
+#define ERR_NCOR 0x00008000 /* Error Not Corrected Indicator */
+
+/* ********** DMA CONTROLLER MASKS *********************8 */
+
+/*DMAx_CONFIG, MDMA_yy_CONFIG Masks */
+#define DMAEN 0x00000001 /* Channel Enable */
+#define WNR 0x00000002 /* Channel Direction (W/R*) */
+#define WDSIZE_8 0x00000000 /* Word Size 8 bits */
+#define WDSIZE_16 0x00000004 /* Word Size 16 bits */
+#define WDSIZE_32 0x00000008 /* Word Size 32 bits */
+#define DMA2D 0x00000010 /* 2D/1D* Mode */
+#define RESTART 0x00000020 /* Restart */
+#define DI_SEL 0x00000040 /* Data Interrupt Select */
+#define DI_EN 0x00000080 /* Data Interrupt Enable */
+#define NDSIZE_0 0x0000 /* Next Descriptor Size = 0 (Stop/Autobuffer) */
+#define NDSIZE_1 0x0100 /* Next Descriptor Size = 1 */
+#define NDSIZE_2 0x0200 /* Next Descriptor Size = 2 */
+#define NDSIZE_3 0x0300 /* Next Descriptor Size = 3 */
+#define NDSIZE_4 0x0400 /* Next Descriptor Size = 4 */
+#define NDSIZE_5 0x0500 /* Next Descriptor Size = 5 */
+#define NDSIZE_6 0x0600 /* Next Descriptor Size = 6 */
+#define NDSIZE_7 0x0700 /* Next Descriptor Size = 7 */
+#define NDSIZE_8 0x0800 /* Next Descriptor Size = 8 */
+#define NDSIZE_9 0x0900 /* Next Descriptor Size = 9 */
+#define NDSIZE 0x00000900 /* Next Descriptor Size */
+#define DMAFLOW 0x00007000 /* Flow Control */
+#define DMAFLOW_STOP 0x0000 /* Stop Mode */
+#define DMAFLOW_AUTO 0x1000 /* Autobuffer Mode */
+#define DMAFLOW_ARRAY 0x4000 /* Descriptor Array Mode */
+#define DMAFLOW_SMALL 0x6000 /* Small Model Descriptor List Mode */
+#define DMAFLOW_LARGE 0x7000 /* Large Model Descriptor List Mode */
+
+#define DMAEN_P 0 /* Channel Enable */
+#define WNR_P 1 /* Channel Direction (W/R*) */
+#define DMA2D_P 4 /* 2D/1D* Mode */
+#define RESTART_P 5 /* Restart */
+#define DI_SEL_P 6 /* Data Interrupt Select */
+#define DI_EN_P 7 /* Data Interrupt Enable */
+
+/*DMAx_IRQ_STATUS, MDMA_yy_IRQ_STATUS Masks */
+
+#define DMA_DONE 0x00000001 /* DMA Done Indicator */
+#define DMA_ERR 0x00000002 /* DMA Error Indicator */
+#define DFETCH 0x00000004 /* Descriptor Fetch Indicator */
+#define DMA_RUN 0x00000008 /* DMA Running Indicator */
+
+#define DMA_DONE_P 0 /* DMA Done Indicator */
+#define DMA_ERR_P 1 /* DMA Error Indicator */
+#define DFETCH_P 2 /* Descriptor Fetch Indicator */
+#define DMA_RUN_P 3 /* DMA Running Indicator */
+
+/*DMAx_PERIPHERAL_MAP, MDMA_yy_PERIPHERAL_MAP Masks */
+
+#define CTYPE 0x00000040 /* DMA Channel Type Indicator */
+#define CTYPE_P 6 /* DMA Channel Type Indicator BIT POSITION */
+#define PCAP8 0x00000080 /* DMA 8-bit Operation Indicator */
+#define PCAP16 0x00000100 /* DMA 16-bit Operation Indicator */
+#define PCAP32 0x00000200 /* DMA 32-bit Operation Indicator */
+#define PCAPWR 0x00000400 /* DMA Write Operation Indicator */
+#define PCAPRD 0x00000800 /* DMA Read Operation Indicator */
+#define PMAP 0x00007000 /* DMA Peripheral Map Field */
+
+#define PMAP_PPI 0x0000 /* PMAP PPI Port DMA */
+#define PMAP_SPORT0RX 0x1000 /* PMAP SPORT0 Receive DMA */
+#define PMAP_SPORT0TX 0x2000 /* PMAP SPORT0 Transmit DMA */
+#define PMAP_SPORT1RX 0x3000 /* PMAP SPORT1 Receive DMA */
+#define PMAP_SPORT1TX 0x4000 /* PMAP SPORT1 Transmit DMA */
+#define PMAP_SPI 0x5000 /* PMAP SPI DMA */
+#define PMAP_UARTRX 0x6000 /* PMAP UART Receive DMA */
+#define PMAP_UARTTX 0x7000 /* PMAP UART Transmit DMA */
+
+/* ************* GENERAL PURPOSE TIMER MASKS ******************** */
+
+/* PWM Timer bit definitions */
+
+/* TIMER_ENABLE Register */
+#define TIMEN0 0x0001
+#define TIMEN1 0x0002
+#define TIMEN2 0x0004
+
+#define TIMEN0_P 0x00
+#define TIMEN1_P 0x01
+#define TIMEN2_P 0x02
+
+/* TIMER_DISABLE Register */
+#define TIMDIS0 0x0001
+#define TIMDIS1 0x0002
+#define TIMDIS2 0x0004
+
+#define TIMDIS0_P 0x00
+#define TIMDIS1_P 0x01
+#define TIMDIS2_P 0x02
+
+/* TIMER_STATUS Register */
+#define TIMIL0 0x0001
+#define TIMIL1 0x0002
+#define TIMIL2 0x0004
+#define TOVF_ERR0 0x0010 /* Timer 0 Counter Overflow */
+#define TOVF_ERR1 0x0020 /* Timer 1 Counter Overflow */
+#define TOVF_ERR2 0x0040 /* Timer 2 Counter Overflow */
+#define TRUN0 0x1000
+#define TRUN1 0x2000
+#define TRUN2 0x4000
+
+#define TIMIL0_P 0x00
+#define TIMIL1_P 0x01
+#define TIMIL2_P 0x02
+#define TOVF_ERR0_P 0x04
+#define TOVF_ERR1_P 0x05
+#define TOVF_ERR2_P 0x06
+#define TRUN0_P 0x0C
+#define TRUN1_P 0x0D
+#define TRUN2_P 0x0E
+
+/* Alternate Deprecated Macros Provided For Backwards Code Compatibility */
+#define TOVL_ERR0 TOVF_ERR0
+#define TOVL_ERR1 TOVF_ERR1
+#define TOVL_ERR2 TOVF_ERR2
+#define TOVL_ERR0_P TOVF_ERR0_P
+#define TOVL_ERR1_P TOVF_ERR1_P
+#define TOVL_ERR2_P TOVF_ERR2_P
+
+/* TIMERx_CONFIG Registers */
+#define PWM_OUT 0x0001
+#define WDTH_CAP 0x0002
+#define EXT_CLK 0x0003
+#define PULSE_HI 0x0004
+#define PERIOD_CNT 0x0008
+#define IRQ_ENA 0x0010
+#define TIN_SEL 0x0020
+#define OUT_DIS 0x0040
+#define CLK_SEL 0x0080
+#define TOGGLE_HI 0x0100
+#define EMU_RUN 0x0200
+#define ERR_TYP(x) ((x & 0x03) << 14)
+
+#define TMODE_P0 0x00
+#define TMODE_P1 0x01
+#define PULSE_HI_P 0x02
+#define PERIOD_CNT_P 0x03
+#define IRQ_ENA_P 0x04
+#define TIN_SEL_P 0x05
+#define OUT_DIS_P 0x06
+#define CLK_SEL_P 0x07
+#define TOGGLE_HI_P 0x08
+#define EMU_RUN_P 0x09
+#define ERR_TYP_P0 0x0E
+#define ERR_TYP_P1 0x0F
+
+/*/ ****************** PROGRAMMABLE FLAG MASKS ********************* */
+
+/* General Purpose IO (0xFFC00700 - 0xFFC007FF) Masks */
+#define PF0 0x0001
+#define PF1 0x0002
+#define PF2 0x0004
+#define PF3 0x0008
+#define PF4 0x0010
+#define PF5 0x0020
+#define PF6 0x0040
+#define PF7 0x0080
+#define PF8 0x0100
+#define PF9 0x0200
+#define PF10 0x0400
+#define PF11 0x0800
+#define PF12 0x1000
+#define PF13 0x2000
+#define PF14 0x4000
+#define PF15 0x8000
+
+/* General Purpose IO (0xFFC00700 - 0xFFC007FF) BIT POSITIONS */
+#define PF0_P 0
+#define PF1_P 1
+#define PF2_P 2
+#define PF3_P 3
+#define PF4_P 4
+#define PF5_P 5
+#define PF6_P 6
+#define PF7_P 7
+#define PF8_P 8
+#define PF9_P 9
+#define PF10_P 10
+#define PF11_P 11
+#define PF12_P 12
+#define PF13_P 13
+#define PF14_P 14
+#define PF15_P 15
+
+/* *********** SERIAL PERIPHERAL INTERFACE (SPI) MASKS **************** */
+
+/* SPI_CTL Masks */
+#define TIMOD 0x00000003 /* Transfer initiation mode and interrupt generation */
+#define RDBR_CORE 0x0000 /* RDBR Read Initiates, IRQ When RDBR Full */
+#define TDBR_CORE 0x0001 /* TDBR Write Initiates, IRQ When TDBR Empty */
+#define RDBR_DMA 0x0002 /* DMA Read, DMA Until FIFO Empty */
+#define TDBR_DMA 0x0003 /* DMA Write, DMA Until FIFO Full */
+#define SZ 0x00000004 /* Send Zero (=0) or last (=1) word when TDBR empty. */
+#define GM 0x00000008 /* When RDBR full, get more (=1) data or discard (=0) incoming Data */
+#define PSSE 0x00000010 /* Enable (=1) Slave-Select input for Master. */
+#define EMISO 0x00000020 /* Enable (=1) MISO pin as an output. */
+#define SIZE 0x00000100 /* Word length (0 => 8 bits, 1 => 16 bits) */
+#define LSBF 0x00000200 /* Data format (0 => MSB sent/received first 1 => LSB sent/received first) */
+#define CPHA 0x00000400 /* Clock phase (0 => SPICLK starts toggling in middle of xfer, 1 => SPICLK toggles at the beginning of xfer. */
+#define CPOL 0x00000800 /* Clock polarity (0 => active-high, 1 => active-low) */
+#define MSTR 0x00001000 /* Configures SPI as master (=1) or slave (=0) */
+#define WOM 0x00002000 /* Open drain (=1) data output enable (for MOSI and MISO) */
+#define SPE 0x00004000 /* SPI module enable (=1), disable (=0) */
+
+/* SPI_FLG Masks */
+#define FLS1 0x00000002 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
+#define FLS2 0x00000004 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
+#define FLS3 0x00000008 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
+#define FLS4 0x00000010 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
+#define FLS5 0x00000020 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
+#define FLS6 0x00000040 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
+#define FLS7 0x00000080 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
+#define FLG1 0x00000200 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
+#define FLG2 0x00000400 /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
+#define FLG3 0x00000800 /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
+#define FLG4 0x00001000 /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
+#define FLG5 0x00002000 /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
+#define FLG6 0x00004000 /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
+#define FLG7 0x00008000 /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
+
+/* SPI_FLG Bit Positions */
+#define FLS1_P 0x00000001 /* Enables (=1) SPI_FLOUT1 as flag output for SPI Slave-select */
+#define FLS2_P 0x00000002 /* Enables (=1) SPI_FLOUT2 as flag output for SPI Slave-select */
+#define FLS3_P 0x00000003 /* Enables (=1) SPI_FLOUT3 as flag output for SPI Slave-select */
+#define FLS4_P 0x00000004 /* Enables (=1) SPI_FLOUT4 as flag output for SPI Slave-select */
+#define FLS5_P 0x00000005 /* Enables (=1) SPI_FLOUT5 as flag output for SPI Slave-select */
+#define FLS6_P 0x00000006 /* Enables (=1) SPI_FLOUT6 as flag output for SPI Slave-select */
+#define FLS7_P 0x00000007 /* Enables (=1) SPI_FLOUT7 as flag output for SPI Slave-select */
+#define FLG1_P 0x00000009 /* Activates (=0) SPI_FLOUT1 as flag output for SPI Slave-select */
+#define FLG2_P 0x0000000A /* Activates (=0) SPI_FLOUT2 as flag output for SPI Slave-select */
+#define FLG3_P 0x0000000B /* Activates (=0) SPI_FLOUT3 as flag output for SPI Slave-select */
+#define FLG4_P 0x0000000C /* Activates (=0) SPI_FLOUT4 as flag output for SPI Slave-select */
+#define FLG5_P 0x0000000D /* Activates (=0) SPI_FLOUT5 as flag output for SPI Slave-select */
+#define FLG6_P 0x0000000E /* Activates (=0) SPI_FLOUT6 as flag output for SPI Slave-select */
+#define FLG7_P 0x0000000F /* Activates (=0) SPI_FLOUT7 as flag output for SPI Slave-select */
+
+/* SPI_STAT Masks */
+#define SPIF 0x00000001 /* Set (=1) when SPI single-word transfer complete */
+#define MODF 0x00000002 /* Set (=1) in a master device when some other device tries to become master */
+#define TXE 0x00000004 /* Set (=1) when transmission occurs with no new data in SPI_TDBR */
+#define TXS 0x00000008 /* SPI_TDBR Data Buffer Status (0=Empty, 1=Full) */
+#define RBSY 0x00000010 /* Set (=1) when data is received with RDBR full */
+#define RXS 0x00000020 /* SPI_RDBR Data Buffer Status (0=Empty, 1=Full) */
+#define TXCOL 0x00000040 /* When set (=1), corrupt data may have been transmitted */
+
+/* SPIx_FLG Masks */
+#define FLG1E 0xFDFF /* Activates SPI_FLOUT1 */
+#define FLG2E 0xFBFF /* Activates SPI_FLOUT2 */
+#define FLG3E 0xF7FF /* Activates SPI_FLOUT3 */
+#define FLG4E 0xEFFF /* Activates SPI_FLOUT4 */
+#define FLG5E 0xDFFF /* Activates SPI_FLOUT5 */
+#define FLG6E 0xBFFF /* Activates SPI_FLOUT6 */
+#define FLG7E 0x7FFF /* Activates SPI_FLOUT7 */
+
+/* ********************* ASYNCHRONOUS MEMORY CONTROLLER MASKS ************* */
+
+/* AMGCTL Masks */
+#define AMCKEN 0x00000001 /* Enable CLKOUT */
+#define AMBEN_NONE 0x00000000 /* All Banks Disabled */
+#define AMBEN_B0 0x00000002 /* Enable Asynchronous Memory Bank 0 only */
+#define AMBEN_B0_B1 0x00000004 /* Enable Asynchronous Memory Banks 0 & 1 only */
+#define AMBEN_B0_B1_B2 0x00000006 /* Enable Asynchronous Memory Banks 0, 1, and 2 */
+#define AMBEN_ALL 0x00000008 /* Enable Asynchronous Memory Banks (all) 0, 1, 2, and 3 */
+
+/* AMGCTL Bit Positions */
+#define AMCKEN_P 0x00000000 /* Enable CLKOUT */
+#define AMBEN_P0 0x00000001 /* Asynchronous Memory Enable, 000 - banks 0-3 disabled, 001 - Bank 0 enabled */
+#define AMBEN_P1 0x00000002 /* Asynchronous Memory Enable, 010 - banks 0&1 enabled, 011 - banks 0-3 enabled */
+#define AMBEN_P2 0x00000003 /* Asynchronous Memory Enable, 1xx - All banks (bank 0, 1, 2, and 3) enabled */
+
+/* AMBCTL0 Masks */
+#define B0RDYEN 0x00000001 /* Bank 0 RDY Enable, 0=disable, 1=enable */
+#define B0RDYPOL 0x00000002 /* Bank 0 RDY Active high, 0=active low, 1=active high */
+#define B0TT_1 0x00000004 /* Bank 0 Transition Time from Read to Write = 1 cycle */
+#define B0TT_2 0x00000008 /* Bank 0 Transition Time from Read to Write = 2 cycles */
+#define B0TT_3 0x0000000C /* Bank 0 Transition Time from Read to Write = 3 cycles */
+#define B0TT_4 0x00000000 /* Bank 0 Transition Time from Read to Write = 4 cycles */
+#define B0ST_1 0x00000010 /* Bank 0 Setup Time from AOE asserted to Read/Write asserted=1 cycle */
+#define B0ST_2 0x00000020 /* Bank 0 Setup Time from AOE asserted to Read/Write asserted=2 cycles */
+#define B0ST_3 0x00000030 /* Bank 0 Setup Time from AOE asserted to Read/Write asserted=3 cycles */
+#define B0ST_4 0x00000000 /* Bank 0 Setup Time from AOE asserted to Read/Write asserted=4 cycles */
+#define B0HT_1 0x00000040 /* Bank 0 Hold Time from Read/Write deasserted to AOE deasserted = 1 cycle */
+#define B0HT_2 0x00000080 /* Bank 0 Hold Time from Read/Write deasserted to AOE deasserted = 2 cycles */
+#define B0HT_3 0x000000C0 /* Bank 0 Hold Time from Read/Write deasserted to AOE deasserted = 3 cycles */
+#define B0HT_0 0x00000000 /* Bank 0 Hold Time from Read/Write deasserted to AOE deasserted = 0 cycles */
+#define B0RAT_1 0x00000100 /* Bank 0 Read Access Time = 1 cycle */
+#define B0RAT_2 0x00000200 /* Bank 0 Read Access Time = 2 cycles */
+#define B0RAT_3 0x00000300 /* Bank 0 Read Access Time = 3 cycles */
+#define B0RAT_4 0x00000400 /* Bank 0 Read Access Time = 4 cycles */
+#define B0RAT_5 0x00000500 /* Bank 0 Read Access Time = 5 cycles */
+#define B0RAT_6 0x00000600 /* Bank 0 Read Access Time = 6 cycles */
+#define B0RAT_7 0x00000700 /* Bank 0 Read Access Time = 7 cycles */
+#define B0RAT_8 0x00000800 /* Bank 0 Read Access Time = 8 cycles */
+#define B0RAT_9 0x00000900 /* Bank 0 Read Access Time = 9 cycles */
+#define B0RAT_10 0x00000A00 /* Bank 0 Read Access Time = 10 cycles */
+#define B0RAT_11 0x00000B00 /* Bank 0 Read Access Time = 11 cycles */
+#define B0RAT_12 0x00000C00 /* Bank 0 Read Access Time = 12 cycles */
+#define B0RAT_13 0x00000D00 /* Bank 0 Read Access Time = 13 cycles */
+#define B0RAT_14 0x00000E00 /* Bank 0 Read Access Time = 14 cycles */
+#define B0RAT_15 0x00000F00 /* Bank 0 Read Access Time = 15 cycles */
+#define B0WAT_1 0x00001000 /* Bank 0 Write Access Time = 1 cycle */
+#define B0WAT_2 0x00002000 /* Bank 0 Write Access Time = 2 cycles */
+#define B0WAT_3 0x00003000 /* Bank 0 Write Access Time = 3 cycles */
+#define B0WAT_4 0x00004000 /* Bank 0 Write Access Time = 4 cycles */
+#define B0WAT_5 0x00005000 /* Bank 0 Write Access Time = 5 cycles */
+#define B0WAT_6 0x00006000 /* Bank 0 Write Access Time = 6 cycles */
+#define B0WAT_7 0x00007000 /* Bank 0 Write Access Time = 7 cycles */
+#define B0WAT_8 0x00008000 /* Bank 0 Write Access Time = 8 cycles */
+#define B0WAT_9 0x00009000 /* Bank 0 Write Access Time = 9 cycles */
+#define B0WAT_10 0x0000A000 /* Bank 0 Write Access Time = 10 cycles */
+#define B0WAT_11 0x0000B000 /* Bank 0 Write Access Time = 11 cycles */
+#define B0WAT_12 0x0000C000 /* Bank 0 Write Access Time = 12 cycles */
+#define B0WAT_13 0x0000D000 /* Bank 0 Write Access Time = 13 cycles */
+#define B0WAT_14 0x0000E000 /* Bank 0 Write Access Time = 14 cycles */
+#define B0WAT_15 0x0000F000 /* Bank 0 Write Access Time = 15 cycles */
+#define B1RDYEN 0x00010000 /* Bank 1 RDY enable, 0=disable, 1=enable */
+#define B1RDYPOL 0x00020000 /* Bank 1 RDY Active high, 0=active low, 1=active high */
+#define B1TT_1 0x00040000 /* Bank 1 Transition Time from Read to Write = 1 cycle */
+#define B1TT_2 0x00080000 /* Bank 1 Transition Time from Read to Write = 2 cycles */
+#define B1TT_3 0x000C0000 /* Bank 1 Transition Time from Read to Write = 3 cycles */
+#define B1TT_4 0x00000000 /* Bank 1 Transition Time from Read to Write = 4 cycles */
+#define B1ST_1 0x00100000 /* Bank 1 Setup Time from AOE asserted to Read or Write asserted = 1 cycle */
+#define B1ST_2 0x00200000 /* Bank 1 Setup Time from AOE asserted to Read or Write asserted = 2 cycles */
+#define B1ST_3 0x00300000 /* Bank 1 Setup Time from AOE asserted to Read or Write asserted = 3 cycles */
+#define B1ST_4 0x00000000 /* Bank 1 Setup Time from AOE asserted to Read or Write asserted = 4 cycles */
+#define B1HT_1 0x00400000 /* Bank 1 Hold Time from Read or Write deasserted to AOE deasserted = 1 cycle */
+#define B1HT_2 0x00800000 /* Bank 1 Hold Time from Read or Write deasserted to AOE deasserted = 2 cycles */
+#define B1HT_3 0x00C00000 /* Bank 1 Hold Time from Read or Write deasserted to AOE deasserted = 3 cycles */
+#define B1HT_0 0x00000000 /* Bank 1 Hold Time from Read or Write deasserted to AOE deasserted = 0 cycles */
+#define B1RAT_1 0x01000000 /* Bank 1 Read Access Time = 1 cycle */
+#define B1RAT_2 0x02000000 /* Bank 1 Read Access Time = 2 cycles */
+#define B1RAT_3 0x03000000 /* Bank 1 Read Access Time = 3 cycles */
+#define B1RAT_4 0x04000000 /* Bank 1 Read Access Time = 4 cycles */
+#define B1RAT_5 0x05000000 /* Bank 1 Read Access Time = 5 cycles */
+#define B1RAT_6 0x06000000 /* Bank 1 Read Access Time = 6 cycles */
+#define B1RAT_7 0x07000000 /* Bank 1 Read Access Time = 7 cycles */
+#define B1RAT_8 0x08000000 /* Bank 1 Read Access Time = 8 cycles */
+#define B1RAT_9 0x09000000 /* Bank 1 Read Access Time = 9 cycles */
+#define B1RAT_10 0x0A000000 /* Bank 1 Read Access Time = 10 cycles */
+#define B1RAT_11 0x0B000000 /* Bank 1 Read Access Time = 11 cycles */
+#define B1RAT_12 0x0C000000 /* Bank 1 Read Access Time = 12 cycles */
+#define B1RAT_13 0x0D000000 /* Bank 1 Read Access Time = 13 cycles */
+#define B1RAT_14 0x0E000000 /* Bank 1 Read Access Time = 14 cycles */
+#define B1RAT_15 0x0F000000 /* Bank 1 Read Access Time = 15 cycles */
+#define B1WAT_1 0x10000000 /* Bank 1 Write Access Time = 1 cycle */
+#define B1WAT_2 0x20000000 /* Bank 1 Write Access Time = 2 cycles */
+#define B1WAT_3 0x30000000 /* Bank 1 Write Access Time = 3 cycles */
+#define B1WAT_4 0x40000000 /* Bank 1 Write Access Time = 4 cycles */
+#define B1WAT_5 0x50000000 /* Bank 1 Write Access Time = 5 cycles */
+#define B1WAT_6 0x60000000 /* Bank 1 Write Access Time = 6 cycles */
+#define B1WAT_7 0x70000000 /* Bank 1 Write Access Time = 7 cycles */
+#define B1WAT_8 0x80000000 /* Bank 1 Write Access Time = 8 cycles */
+#define B1WAT_9 0x90000000 /* Bank 1 Write Access Time = 9 cycles */
+#define B1WAT_10 0xA0000000 /* Bank 1 Write Access Time = 10 cycles */
+#define B1WAT_11 0xB0000000 /* Bank 1 Write Access Time = 11 cycles */
+#define B1WAT_12 0xC0000000 /* Bank 1 Write Access Time = 12 cycles */
+#define B1WAT_13 0xD0000000 /* Bank 1 Write Access Time = 13 cycles */
+#define B1WAT_14 0xE0000000 /* Bank 1 Write Access Time = 14 cycles */
+#define B1WAT_15 0xF0000000 /* Bank 1 Write Access Time = 15 cycles */
+
+/* AMBCTL1 Masks */
+#define B2RDYEN 0x00000001 /* Bank 2 RDY Enable, 0=disable, 1=enable */
+#define B2RDYPOL 0x00000002 /* Bank 2 RDY Active high, 0=active low, 1=active high */
+#define B2TT_1 0x00000004 /* Bank 2 Transition Time from Read to Write = 1 cycle */
+#define B2TT_2 0x00000008 /* Bank 2 Transition Time from Read to Write = 2 cycles */
+#define B2TT_3 0x0000000C /* Bank 2 Transition Time from Read to Write = 3 cycles */
+#define B2TT_4 0x00000000 /* Bank 2 Transition Time from Read to Write = 4 cycles */
+#define B2ST_1 0x00000010 /* Bank 2 Setup Time from AOE asserted to Read or Write asserted = 1 cycle */
+#define B2ST_2 0x00000020 /* Bank 2 Setup Time from AOE asserted to Read or Write asserted = 2 cycles */
+#define B2ST_3 0x00000030 /* Bank 2 Setup Time from AOE asserted to Read or Write asserted = 3 cycles */
+#define B2ST_4 0x00000000 /* Bank 2 Setup Time from AOE asserted to Read or Write asserted = 4 cycles */
+#define B2HT_1 0x00000040 /* Bank 2 Hold Time from Read or Write deasserted to AOE deasserted = 1 cycle */
+#define B2HT_2 0x00000080 /* Bank 2 Hold Time from Read or Write deasserted to AOE deasserted = 2 cycles */
+#define B2HT_3 0x000000C0 /* Bank 2 Hold Time from Read or Write deasserted to AOE deasserted = 3 cycles */
+#define B2HT_0 0x00000000 /* Bank 2 Hold Time from Read or Write deasserted to AOE deasserted = 0 cycles */
+#define B2RAT_1 0x00000100 /* Bank 2 Read Access Time = 1 cycle */
+#define B2RAT_2 0x00000200 /* Bank 2 Read Access Time = 2 cycles */
+#define B2RAT_3 0x00000300 /* Bank 2 Read Access Time = 3 cycles */
+#define B2RAT_4 0x00000400 /* Bank 2 Read Access Time = 4 cycles */
+#define B2RAT_5 0x00000500 /* Bank 2 Read Access Time = 5 cycles */
+#define B2RAT_6 0x00000600 /* Bank 2 Read Access Time = 6 cycles */
+#define B2RAT_7 0x00000700 /* Bank 2 Read Access Time = 7 cycles */
+#define B2RAT_8 0x00000800 /* Bank 2 Read Access Time = 8 cycles */
+#define B2RAT_9 0x00000900 /* Bank 2 Read Access Time = 9 cycles */
+#define B2RAT_10 0x00000A00 /* Bank 2 Read Access Time = 10 cycles */
+#define B2RAT_11 0x00000B00 /* Bank 2 Read Access Time = 11 cycles */
+#define B2RAT_12 0x00000C00 /* Bank 2 Read Access Time = 12 cycles */
+#define B2RAT_13 0x00000D00 /* Bank 2 Read Access Time = 13 cycles */
+#define B2RAT_14 0x00000E00 /* Bank 2 Read Access Time = 14 cycles */
+#define B2RAT_15 0x00000F00 /* Bank 2 Read Access Time = 15 cycles */
+#define B2WAT_1 0x00001000 /* Bank 2 Write Access Time = 1 cycle */
+#define B2WAT_2 0x00002000 /* Bank 2 Write Access Time = 2 cycles */
+#define B2WAT_3 0x00003000 /* Bank 2 Write Access Time = 3 cycles */
+#define B2WAT_4 0x00004000 /* Bank 2 Write Access Time = 4 cycles */
+#define B2WAT_5 0x00005000 /* Bank 2 Write Access Time = 5 cycles */
+#define B2WAT_6 0x00006000 /* Bank 2 Write Access Time = 6 cycles */
+#define B2WAT_7 0x00007000 /* Bank 2 Write Access Time = 7 cycles */
+#define B2WAT_8 0x00008000 /* Bank 2 Write Access Time = 8 cycles */
+#define B2WAT_9 0x00009000 /* Bank 2 Write Access Time = 9 cycles */
+#define B2WAT_10 0x0000A000 /* Bank 2 Write Access Time = 10 cycles */
+#define B2WAT_11 0x0000B000 /* Bank 2 Write Access Time = 11 cycles */
+#define B2WAT_12 0x0000C000 /* Bank 2 Write Access Time = 12 cycles */
+#define B2WAT_13 0x0000D000 /* Bank 2 Write Access Time = 13 cycles */
+#define B2WAT_14 0x0000E000 /* Bank 2 Write Access Time = 14 cycles */
+#define B2WAT_15 0x0000F000 /* Bank 2 Write Access Time = 15 cycles */
+#define B3RDYEN 0x00010000 /* Bank 3 RDY enable, 0=disable, 1=enable */
+#define B3RDYPOL 0x00020000 /* Bank 3 RDY Active high, 0=active low, 1=active high */
+#define B3TT_1 0x00040000 /* Bank 3 Transition Time from Read to Write = 1 cycle */
+#define B3TT_2 0x00080000 /* Bank 3 Transition Time from Read to Write = 2 cycles */
+#define B3TT_3 0x000C0000 /* Bank 3 Transition Time from Read to Write = 3 cycles */
+#define B3TT_4 0x00000000 /* Bank 3 Transition Time from Read to Write = 4 cycles */
+#define B3ST_1 0x00100000 /* Bank 3 Setup Time from AOE asserted to Read or Write asserted = 1 cycle */
+#define B3ST_2 0x00200000 /* Bank 3 Setup Time from AOE asserted to Read or Write asserted = 2 cycles */
+#define B3ST_3 0x00300000 /* Bank 3 Setup Time from AOE asserted to Read or Write asserted = 3 cycles */
+#define B3ST_4 0x00000000 /* Bank 3 Setup Time from AOE asserted to Read or Write asserted = 4 cycles */
+#define B3HT_1 0x00400000 /* Bank 3 Hold Time from Read or Write deasserted to AOE deasserted = 1 cycle */
+#define B3HT_2 0x00800000 /* Bank 3 Hold Time from Read or Write deasserted to AOE deasserted = 2 cycles */
+#define B3HT_3 0x00C00000 /* Bank 3 Hold Time from Read or Write deasserted to AOE deasserted = 3 cycles */
+#define B3HT_0 0x00000000 /* Bank 3 Hold Time from Read or Write deasserted to AOE deasserted = 0 cycles */
+#define B3RAT_1 0x01000000 /* Bank 3 Read Access Time = 1 cycle */
+#define B3RAT_2 0x02000000 /* Bank 3 Read Access Time = 2 cycles */
+#define B3RAT_3 0x03000000 /* Bank 3 Read Access Time = 3 cycles */
+#define B3RAT_4 0x04000000 /* Bank 3 Read Access Time = 4 cycles */
+#define B3RAT_5 0x05000000 /* Bank 3 Read Access Time = 5 cycles */
+#define B3RAT_6 0x06000000 /* Bank 3 Read Access Time = 6 cycles */
+#define B3RAT_7 0x07000000 /* Bank 3 Read Access Time = 7 cycles */
+#define B3RAT_8 0x08000000 /* Bank 3 Read Access Time = 8 cycles */
+#define B3RAT_9 0x09000000 /* Bank 3 Read Access Time = 9 cycles */
+#define B3RAT_10 0x0A000000 /* Bank 3 Read Access Time = 10 cycles */
+#define B3RAT_11 0x0B000000 /* Bank 3 Read Access Time = 11 cycles */
+#define B3RAT_12 0x0C000000 /* Bank 3 Read Access Time = 12 cycles */
+#define B3RAT_13 0x0D000000 /* Bank 3 Read Access Time = 13 cycles */
+#define B3RAT_14 0x0E000000 /* Bank 3 Read Access Time = 14 cycles */
+#define B3RAT_15 0x0F000000 /* Bank 3 Read Access Time = 15 cycles */
+#define B3WAT_1 0x10000000 /* Bank 3 Write Access Time = 1 cycle */
+#define B3WAT_2 0x20000000 /* Bank 3 Write Access Time = 2 cycles */
+#define B3WAT_3 0x30000000 /* Bank 3 Write Access Time = 3 cycles */
+#define B3WAT_4 0x40000000 /* Bank 3 Write Access Time = 4 cycles */
+#define B3WAT_5 0x50000000 /* Bank 3 Write Access Time = 5 cycles */
+#define B3WAT_6 0x60000000 /* Bank 3 Write Access Time = 6 cycles */
+#define B3WAT_7 0x70000000 /* Bank 3 Write Access Time = 7 cycles */
+#define B3WAT_8 0x80000000 /* Bank 3 Write Access Time = 8 cycles */
+#define B3WAT_9 0x90000000 /* Bank 3 Write Access Time = 9 cycles */
+#define B3WAT_10 0xA0000000 /* Bank 3 Write Access Time = 10 cycles */
+#define B3WAT_11 0xB0000000 /* Bank 3 Write Access Time = 11 cycles */
+#define B3WAT_12 0xC0000000 /* Bank 3 Write Access Time = 12 cycles */
+#define B3WAT_13 0xD0000000 /* Bank 3 Write Access Time = 13 cycles */
+#define B3WAT_14 0xE0000000 /* Bank 3 Write Access Time = 14 cycles */
+#define B3WAT_15 0xF0000000 /* Bank 3 Write Access Time = 15 cycles */
+
+/* ********************** SDRAM CONTROLLER MASKS *************************** */
+
+/* SDGCTL Masks */
+#define SCTLE 0x00000001 /* Enable SCLK[0], /SRAS, /SCAS, /SWE, SDQM[3:0] */
+#define CL_2 0x00000008 /* SDRAM CAS latency = 2 cycles */
+#define CL_3 0x0000000C /* SDRAM CAS latency = 3 cycles */
+#define PFE 0x00000010 /* Enable SDRAM prefetch */
+#define PFP 0x00000020 /* Prefetch has priority over AMC requests */
+#define PASR_ALL 0x00000000 /* All 4 SDRAM Banks Refreshed In Self-Refresh */
+#define PASR_B0_B1 0x00000010 /* SDRAM Banks 0 and 1 Are Refreshed In Self-Refresh */
+#define PASR_B0 0x00000020 /* Only SDRAM Bank 0 Is Refreshed In Self-Refresh */
+#define TRAS_1 0x00000040 /* SDRAM tRAS = 1 cycle */
+#define TRAS_2 0x00000080 /* SDRAM tRAS = 2 cycles */
+#define TRAS_3 0x000000C0 /* SDRAM tRAS = 3 cycles */
+#define TRAS_4 0x00000100 /* SDRAM tRAS = 4 cycles */
+#define TRAS_5 0x00000140 /* SDRAM tRAS = 5 cycles */
+#define TRAS_6 0x00000180 /* SDRAM tRAS = 6 cycles */
+#define TRAS_7 0x000001C0 /* SDRAM tRAS = 7 cycles */
+#define TRAS_8 0x00000200 /* SDRAM tRAS = 8 cycles */
+#define TRAS_9 0x00000240 /* SDRAM tRAS = 9 cycles */
+#define TRAS_10 0x00000280 /* SDRAM tRAS = 10 cycles */
+#define TRAS_11 0x000002C0 /* SDRAM tRAS = 11 cycles */
+#define TRAS_12 0x00000300 /* SDRAM tRAS = 12 cycles */
+#define TRAS_13 0x00000340 /* SDRAM tRAS = 13 cycles */
+#define TRAS_14 0x00000380 /* SDRAM tRAS = 14 cycles */
+#define TRAS_15 0x000003C0 /* SDRAM tRAS = 15 cycles */
+#define TRP_1 0x00000800 /* SDRAM tRP = 1 cycle */
+#define TRP_2 0x00001000 /* SDRAM tRP = 2 cycles */
+#define TRP_3 0x00001800 /* SDRAM tRP = 3 cycles */
+#define TRP_4 0x00002000 /* SDRAM tRP = 4 cycles */
+#define TRP_5 0x00002800 /* SDRAM tRP = 5 cycles */
+#define TRP_6 0x00003000 /* SDRAM tRP = 6 cycles */
+#define TRP_7 0x00003800 /* SDRAM tRP = 7 cycles */
+#define TRCD_1 0x00008000 /* SDRAM tRCD = 1 cycle */
+#define TRCD_2 0x00010000 /* SDRAM tRCD = 2 cycles */
+#define TRCD_3 0x00018000 /* SDRAM tRCD = 3 cycles */
+#define TRCD_4 0x00020000 /* SDRAM tRCD = 4 cycles */
+#define TRCD_5 0x00028000 /* SDRAM tRCD = 5 cycles */
+#define TRCD_6 0x00030000 /* SDRAM tRCD = 6 cycles */
+#define TRCD_7 0x00038000 /* SDRAM tRCD = 7 cycles */
+#define TWR_1 0x00080000 /* SDRAM tWR = 1 cycle */
+#define TWR_2 0x00100000 /* SDRAM tWR = 2 cycles */
+#define TWR_3 0x00180000 /* SDRAM tWR = 3 cycles */
+#define PUPSD 0x00200000 /*Power-up start delay */
+#define PSM 0x00400000 /* SDRAM power-up sequence = Precharge, mode register set, 8 CBR refresh cycles */
+#define PSS 0x00800000 /* enable SDRAM power-up sequence on next SDRAM access */
+#define SRFS 0x01000000 /* Start SDRAM self-refresh mode */
+#define EBUFE 0x02000000 /* Enable external buffering timing */
+#define FBBRW 0x04000000 /* Fast back-to-back read write enable */
+#define EMREN 0x10000000 /* Extended mode register enable */
+#define TCSR 0x20000000 /* Temp compensated self refresh value 85 deg C */
+#define CDDBG 0x40000000 /* Tristate SDRAM controls during bus grant */
+
+/* EBIU_SDBCTL Masks */
+#define EBE 0x00000001 /* Enable SDRAM external bank */
+#define EBSZ_16 0x00000000 /* SDRAM external bank size = 16MB */
+#define EBSZ_32 0x00000002 /* SDRAM external bank size = 32MB */
+#define EBSZ_64 0x00000004 /* SDRAM external bank size = 64MB */
+#define EBSZ_128 0x00000006 /* SDRAM external bank size = 128MB */
+#define EBCAW_8 0x00000000 /* SDRAM external bank column address width = 8 bits */
+#define EBCAW_9 0x00000010 /* SDRAM external bank column address width = 9 bits */
+#define EBCAW_10 0x00000020 /* SDRAM external bank column address width = 9 bits */
+#define EBCAW_11 0x00000030 /* SDRAM external bank column address width = 9 bits */
+
+/* EBIU_SDSTAT Masks */
+#define SDCI 0x00000001 /* SDRAM controller is idle */
+#define SDSRA 0x00000002 /* SDRAM SDRAM self refresh is active */
+#define SDPUA 0x00000004 /* SDRAM power up active */
+#define SDRS 0x00000008 /* SDRAM is in reset state */
+#define SDEASE 0x00000010 /* SDRAM EAB sticky error status - W1C */
+#define BGSTAT 0x00000020 /* Bus granted */
+
+
+#endif /* _DEF_BF532_H */
diff --git a/arch/blackfin/mach-bf533/include/mach/dma.h b/arch/blackfin/mach-bf533/include/mach/dma.h
new file mode 100644
index 0000000..bd9d5e9
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/dma.h
@@ -0,0 +1,54 @@
+/*****************************************************************************
+*
+* BF-533/2/1 Specific Declarations
+*
+****************************************************************************/
+/*
+ * File: include/asm-blackfin/mach-bf533/dma.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _MACH_DMA_H_
+#define _MACH_DMA_H_
+
+#define MAX_BLACKFIN_DMA_CHANNEL 12
+
+#define CH_PPI 0
+#define CH_SPORT0_RX 1
+#define CH_SPORT0_TX 2
+#define CH_SPORT1_RX 3
+#define CH_SPORT1_TX 4
+#define CH_SPI 5
+#define CH_UART_RX 6
+#define CH_UART_TX 7
+#define CH_MEM_STREAM0_DEST 8 /* TX */
+#define CH_MEM_STREAM0_SRC 9 /* RX */
+#define CH_MEM_STREAM1_DEST 10 /* TX */
+#define CH_MEM_STREAM1_SRC 11 /* RX */
+
+#endif
diff --git a/arch/blackfin/mach-bf533/include/mach/irq.h b/arch/blackfin/mach-bf533/include/mach/irq.h
new file mode 100644
index 0000000..5aa38e5
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/irq.h
@@ -0,0 +1,173 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/defBF532.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _BF533_IRQ_H_
+#define _BF533_IRQ_H_
+
+/*
+ * Interrupt source definitions
+ Event Source Core Event Name
+Core Emulation **
+ Events (highest priority) EMU 0
+ Reset RST 1
+ NMI NMI 2
+ Exception EVX 3
+ Reserved -- 4
+ Hardware Error IVHW 5
+ Core Timer IVTMR 6 *
+ PLL Wakeup Interrupt IVG7 7
+ DMA Error (generic) IVG7 8
+ PPI Error Interrupt IVG7 9
+ SPORT0 Error Interrupt IVG7 10
+ SPORT1 Error Interrupt IVG7 11
+ SPI Error Interrupt IVG7 12
+ UART Error Interrupt IVG7 13
+ RTC Interrupt IVG8 14
+ DMA0 Interrupt (PPI) IVG8 15
+ DMA1 (SPORT0 RX) IVG9 16
+ DMA2 (SPORT0 TX) IVG9 17
+ DMA3 (SPORT1 RX) IVG9 18
+ DMA4 (SPORT1 TX) IVG9 19
+ DMA5 (PPI) IVG10 20
+ DMA6 (UART RX) IVG10 21
+ DMA7 (UART TX) IVG10 22
+ Timer0 IVG11 23
+ Timer1 IVG11 24
+ Timer2 IVG11 25
+ PF Interrupt A IVG12 26
+ PF Interrupt B IVG12 27
+ DMA8/9 Interrupt IVG13 28
+ DMA10/11 Interrupt IVG13 29
+ Watchdog Timer IVG13 30
+
+ Softirq IVG14 31
+ System Call --
+ (lowest priority) IVG15 32 *
+ */
+#define SYS_IRQS 31
+#define NR_PERI_INTS 24
+
+/* The ABSTRACT IRQ definitions */
+/** the first seven of the following are fixed, the rest you change if you need to **/
+#define IRQ_EMU 0 /*Emulation */
+#define IRQ_RST 1 /*reset */
+#define IRQ_NMI 2 /*Non Maskable */
+#define IRQ_EVX 3 /*Exception */
+#define IRQ_UNUSED 4 /*- unused interrupt*/
+#define IRQ_HWERR 5 /*Hardware Error */
+#define IRQ_CORETMR 6 /*Core timer */
+
+#define IRQ_PLL_WAKEUP 7 /*PLL Wakeup Interrupt */
+#define IRQ_DMA_ERROR 8 /*DMA Error (general) */
+#define IRQ_PPI_ERROR 9 /*PPI Error Interrupt */
+#define IRQ_SPORT0_ERROR 10 /*SPORT0 Error Interrupt */
+#define IRQ_SPORT1_ERROR 11 /*SPORT1 Error Interrupt */
+#define IRQ_SPI_ERROR 12 /*SPI Error Interrupt */
+#define IRQ_UART_ERROR 13 /*UART Error Interrupt */
+#define IRQ_RTC 14 /*RTC Interrupt */
+#define IRQ_PPI 15 /*DMA0 Interrupt (PPI) */
+#define IRQ_SPORT0_RX 16 /*DMA1 Interrupt (SPORT0 RX) */
+#define IRQ_SPORT0_TX 17 /*DMA2 Interrupt (SPORT0 TX) */
+#define IRQ_SPORT1_RX 18 /*DMA3 Interrupt (SPORT1 RX) */
+#define IRQ_SPORT1_TX 19 /*DMA4 Interrupt (SPORT1 TX) */
+#define IRQ_SPI 20 /*DMA5 Interrupt (SPI) */
+#define IRQ_UART_RX 21 /*DMA6 Interrupt (UART RX) */
+#define IRQ_UART_TX 22 /*DMA7 Interrupt (UART TX) */
+#define IRQ_TMR0 23 /*Timer 0 */
+#define IRQ_TMR1 24 /*Timer 1 */
+#define IRQ_TMR2 25 /*Timer 2 */
+#define IRQ_PROG_INTA 26 /*Programmable Flags A (8) */
+#define IRQ_PROG_INTB 27 /*Programmable Flags B (8) */
+#define IRQ_MEM_DMA0 28 /*DMA8/9 Interrupt (Memory DMA Stream 0) */
+#define IRQ_MEM_DMA1 29 /*DMA10/11 Interrupt (Memory DMA Stream 1) */
+#define IRQ_WATCH 30 /*Watch Dog Timer */
+
+#define IRQ_PF0 33
+#define IRQ_PF1 34
+#define IRQ_PF2 35
+#define IRQ_PF3 36
+#define IRQ_PF4 37
+#define IRQ_PF5 38
+#define IRQ_PF6 39
+#define IRQ_PF7 40
+#define IRQ_PF8 41
+#define IRQ_PF9 42
+#define IRQ_PF10 43
+#define IRQ_PF11 44
+#define IRQ_PF12 45
+#define IRQ_PF13 46
+#define IRQ_PF14 47
+#define IRQ_PF15 48
+
+#define GPIO_IRQ_BASE IRQ_PF0
+
+#define NR_IRQS (IRQ_PF15+1)
+
+#define IVG7 7
+#define IVG8 8
+#define IVG9 9
+#define IVG10 10
+#define IVG11 11
+#define IVG12 12
+#define IVG13 13
+#define IVG14 14
+#define IVG15 15
+
+/* IAR0 BIT FIELDS*/
+#define RTC_ERROR_POS 28
+#define UART_ERROR_POS 24
+#define SPORT1_ERROR_POS 20
+#define SPI_ERROR_POS 16
+#define SPORT0_ERROR_POS 12
+#define PPI_ERROR_POS 8
+#define DMA_ERROR_POS 4
+#define PLLWAKE_ERROR_POS 0
+
+/* IAR1 BIT FIELDS*/
+#define DMA7_UARTTX_POS 28
+#define DMA6_UARTRX_POS 24
+#define DMA5_SPI_POS 20
+#define DMA4_SPORT1TX_POS 16
+#define DMA3_SPORT1RX_POS 12
+#define DMA2_SPORT0TX_POS 8
+#define DMA1_SPORT0RX_POS 4
+#define DMA0_PPI_POS 0
+
+/* IAR2 BIT FIELDS*/
+#define WDTIMER_POS 28
+#define MEMDMA1_POS 24
+#define MEMDMA0_POS 20
+#define PFB_POS 16
+#define PFA_POS 12
+#define TIMER2_POS 8
+#define TIMER1_POS 4
+#define TIMER0_POS 0
+
+#endif /* _BF533_IRQ_H_ */
diff --git a/arch/blackfin/mach-bf533/include/mach/mem_init.h b/arch/blackfin/mach-bf533/include/mach/mem_init.h
new file mode 100644
index 0000000..ed2034b
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/mem_init.h
@@ -0,0 +1,297 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/mem_init.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || \
+ CONFIG_MEM_MT48LC32M16A2TG_75 || CONFIG_MEM_GENERIC_BOARD)
+#if (CONFIG_SCLK_HZ > 119402985)
+#define SDRAM_tRP TRP_2
+#define SDRAM_tRP_num 2
+#define SDRAM_tRAS TRAS_7
+#define SDRAM_tRAS_num 7
+#define SDRAM_tRCD TRCD_2
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 104477612) && (CONFIG_SCLK_HZ <= 119402985)
+#define SDRAM_tRP TRP_2
+#define SDRAM_tRP_num 2
+#define SDRAM_tRAS TRAS_6
+#define SDRAM_tRAS_num 6
+#define SDRAM_tRCD TRCD_2
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612)
+#define SDRAM_tRP TRP_2
+#define SDRAM_tRP_num 2
+#define SDRAM_tRAS TRAS_5
+#define SDRAM_tRAS_num 5
+#define SDRAM_tRCD TRCD_2
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 74626866) && (CONFIG_SCLK_HZ <= 89552239)
+#define SDRAM_tRP TRP_2
+#define SDRAM_tRP_num 2
+#define SDRAM_tRAS TRAS_4
+#define SDRAM_tRAS_num 4
+#define SDRAM_tRCD TRCD_2
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 66666667) && (CONFIG_SCLK_HZ <= 74626866)
+#define SDRAM_tRP TRP_2
+#define SDRAM_tRP_num 2
+#define SDRAM_tRAS TRAS_3
+#define SDRAM_tRAS_num 3
+#define SDRAM_tRCD TRCD_2
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 59701493) && (CONFIG_SCLK_HZ <= 66666667)
+#define SDRAM_tRP TRP_1
+#define SDRAM_tRP_num 1
+#define SDRAM_tRAS TRAS_4
+#define SDRAM_tRAS_num 3
+#define SDRAM_tRCD TRCD_1
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 44776119) && (CONFIG_SCLK_HZ <= 59701493)
+#define SDRAM_tRP TRP_1
+#define SDRAM_tRP_num 1
+#define SDRAM_tRAS TRAS_3
+#define SDRAM_tRAS_num 3
+#define SDRAM_tRCD TRCD_1
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 29850746) && (CONFIG_SCLK_HZ <= 44776119)
+#define SDRAM_tRP TRP_1
+#define SDRAM_tRP_num 1
+#define SDRAM_tRAS TRAS_2
+#define SDRAM_tRAS_num 2
+#define SDRAM_tRCD TRCD_1
+#define SDRAM_tWR TWR_2
+#endif
+#if (CONFIG_SCLK_HZ <= 29850746)
+#define SDRAM_tRP TRP_1
+#define SDRAM_tRP_num 1
+#define SDRAM_tRAS TRAS_1
+#define SDRAM_tRAS_num 1
+#define SDRAM_tRCD TRCD_1
+#define SDRAM_tWR TWR_2
+#endif
+#endif
+
+#if (CONFIG_MEM_MT48LC16M16A2TG_75)
+ /*SDRAM INFORMATION: */
+#define SDRAM_Tref 64 /* Refresh period in milliseconds */
+#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+#define SDRAM_CL CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC64M4A2FB_7E)
+ /*SDRAM INFORMATION: */
+#define SDRAM_Tref 64 /* Refresh period in milliseconds */
+#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+#define SDRAM_CL CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC32M16A2TG_75)
+ /*SDRAM INFORMATION: */
+#define SDRAM_Tref 64 /* Refresh period in milliseconds */
+#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+#define SDRAM_CL CL_3
+#endif
+
+#if (CONFIG_MEM_GENERIC_BOARD)
+ /*SDRAM INFORMATION: Modify this for your board */
+#define SDRAM_Tref 64 /* Refresh period in milliseconds */
+#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */
+#define SDRAM_CL CL_3
+#endif
+
+/* Equation from section 17 (p17-46) of BF533 HRM */
+#define mem_SDRRC (((CONFIG_SCLK_HZ / 1000) * SDRAM_Tref) / SDRAM_NRA) - (SDRAM_tRAS_num + SDRAM_tRP_num)
+
+/* Enable SCLK Out */
+#define mem_SDGCTL (SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR | PSS)
+
+#if defined CONFIG_CLKIN_HALF
+#define CLKIN_HALF 1
+#else
+#define CLKIN_HALF 0
+#endif
+
+#if defined CONFIG_PLL_BYPASS
+#define PLL_BYPASS 1
+#else
+#define PLL_BYPASS 0
+#endif
+
+/***************************************Currently Not Being Used *********************************/
+#define flash_EBIU_AMBCTL_WAT ((CONFIG_FLASH_SPEED_BWAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_RAT ((CONFIG_FLASH_SPEED_BRAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_HT ((CONFIG_FLASH_SPEED_BHT * 4) / (4000000000 / CONFIG_SCLK_HZ))
+#define flash_EBIU_AMBCTL_ST ((CONFIG_FLASH_SPEED_BST * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_TT ((CONFIG_FLASH_SPEED_BTT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+
+#if (flash_EBIU_AMBCTL_TT > 3)
+#define flash_EBIU_AMBCTL0_TT B0TT_4
+#endif
+#if (flash_EBIU_AMBCTL_TT == 3)
+#define flash_EBIU_AMBCTL0_TT B0TT_3
+#endif
+#if (flash_EBIU_AMBCTL_TT == 2)
+#define flash_EBIU_AMBCTL0_TT B0TT_2
+#endif
+#if (flash_EBIU_AMBCTL_TT < 2)
+#define flash_EBIU_AMBCTL0_TT B0TT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_ST > 3)
+#define flash_EBIU_AMBCTL0_ST B0ST_4
+#endif
+#if (flash_EBIU_AMBCTL_ST == 3)
+#define flash_EBIU_AMBCTL0_ST B0ST_3
+#endif
+#if (flash_EBIU_AMBCTL_ST == 2)
+#define flash_EBIU_AMBCTL0_ST B0ST_2
+#endif
+#if (flash_EBIU_AMBCTL_ST < 2)
+#define flash_EBIU_AMBCTL0_ST B0ST_1
+#endif
+
+#if (flash_EBIU_AMBCTL_HT > 2)
+#define flash_EBIU_AMBCTL0_HT B0HT_3
+#endif
+#if (flash_EBIU_AMBCTL_HT == 2)
+#define flash_EBIU_AMBCTL0_HT B0HT_2
+#endif
+#if (flash_EBIU_AMBCTL_HT == 1)
+#define flash_EBIU_AMBCTL0_HT B0HT_1
+#endif
+#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT == 0)
+#define flash_EBIU_AMBCTL0_HT B0HT_0
+#endif
+#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT != 0)
+#define flash_EBIU_AMBCTL0_HT B0HT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_WAT > 14)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_15
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 14)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_14
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 13)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_13
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 12)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_12
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 11)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_11
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 10)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_10
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 9)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_9
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 8)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_8
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 7)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_7
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 6)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_6
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 5)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_5
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 4)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_4
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 3)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_3
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 2)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_2
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 1)
+#define flash_EBIU_AMBCTL0_WAT B0WAT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_RAT > 14)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_15
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 14)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_14
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 13)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_13
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 12)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_12
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 11)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_11
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 10)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_10
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 9)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_9
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 8)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_8
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 7)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_7
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 6)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_6
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 5)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_5
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 4)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_4
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 3)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_3
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 2)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_2
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 1)
+#define flash_EBIU_AMBCTL0_RAT B0RAT_1
+#endif
+
+#define flash_EBIU_AMBCTL0 \
+ (flash_EBIU_AMBCTL0_WAT | flash_EBIU_AMBCTL0_RAT | flash_EBIU_AMBCTL0_HT | \
+ flash_EBIU_AMBCTL0_ST | flash_EBIU_AMBCTL0_TT | CONFIG_FLASH_SPEED_RDYEN)
diff --git a/arch/blackfin/mach-bf533/include/mach/mem_map.h b/arch/blackfin/mach-bf533/include/mach/mem_map.h
new file mode 100644
index 0000000..581fc6e
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/mem_map.h
@@ -0,0 +1,171 @@
+/*
+ * File: include/asm-blackfin/mach-bf533/mem_map.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _MEM_MAP_533_H_
+#define _MEM_MAP_533_H_
+
+#define COREMMR_BASE 0xFFE00000 /* Core MMRs */
+#define SYSMMR_BASE 0xFFC00000 /* System MMRs */
+
+/* Async Memory Banks */
+#define ASYNC_BANK3_BASE 0x20300000 /* Async Bank 3 */
+#define ASYNC_BANK3_SIZE 0x00100000 /* 1M */
+#define ASYNC_BANK2_BASE 0x20200000 /* Async Bank 2 */
+#define ASYNC_BANK2_SIZE 0x00100000 /* 1M */
+#define ASYNC_BANK1_BASE 0x20100000 /* Async Bank 1 */
+#define ASYNC_BANK1_SIZE 0x00100000 /* 1M */
+#define ASYNC_BANK0_BASE 0x20000000 /* Async Bank 0 */
+#define ASYNC_BANK0_SIZE 0x00100000 /* 1M */
+
+/* Boot ROM Memory */
+
+#define BOOT_ROM_START 0xEF000000
+#define BOOT_ROM_LENGTH 0x400
+
+/* Level 1 Memory */
+
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE (16*1024)
+#else
+#define BFIN_ICACHESIZE (0*1024)
+#endif
+
+/* Memory Map for ADSP-BF533 processors */
+
+#ifdef CONFIG_BF533
+#define L1_CODE_START 0xFFA00000
+#define L1_DATA_A_START 0xFF800000
+#define L1_DATA_B_START 0xFF900000
+
+#ifdef CONFIG_BFIN_ICACHE
+#define L1_CODE_LENGTH (0x14000 - 0x4000)
+#else
+#define L1_CODE_LENGTH 0x14000
+#endif
+
+#ifdef CONFIG_BFIN_DCACHE
+
+#ifdef CONFIG_BFIN_DCACHE_BANKA
+#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH 0x8000
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
+#else
+#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH (0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH (0x8000 - 0x4000)
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
+#endif
+
+#else
+#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH 0x8000
+#define L1_DATA_B_LENGTH 0x8000
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
+#endif
+
+/* Memory Map for ADSP-BF532 processors */
+
+#ifdef CONFIG_BF532
+#define L1_CODE_START 0xFFA08000
+#define L1_DATA_A_START 0xFF804000
+#define L1_DATA_B_START 0xFF904000
+
+#ifdef CONFIG_BFIN_ICACHE
+#define L1_CODE_LENGTH (0xC000 - 0x4000)
+#else
+#define L1_CODE_LENGTH 0xC000
+#endif
+
+#ifdef CONFIG_BFIN_DCACHE
+
+#ifdef CONFIG_BFIN_DCACHE_BANKA
+#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
+#define L1_DATA_B_LENGTH 0x4000
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
+
+#else
+#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
+#define L1_DATA_B_LENGTH (0x4000 - 0x4000)
+#define BFIN_DCACHESIZE (32*1024)
+#define BFIN_DSUPBANKS 2
+#endif
+
+#else
+#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH 0x4000
+#define L1_DATA_B_LENGTH 0x4000
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif /*CONFIG_BFIN_DCACHE*/
+#endif
+
+/* Memory Map for ADSP-BF531 processors */
+
+#ifdef CONFIG_BF531
+#define L1_CODE_START 0xFFA08000
+#define L1_DATA_A_START 0xFF804000
+#define L1_DATA_B_START 0xFF904000
+#define L1_CODE_LENGTH 0x4000
+#define L1_DATA_B_LENGTH 0x0000
+
+
+#ifdef CONFIG_BFIN_DCACHE
+#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH (0x4000 - 0x4000)
+#define BFIN_DCACHESIZE (16*1024)
+#define BFIN_DSUPBANKS 1
+#else
+#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH 0x4000
+#define BFIN_DCACHESIZE (0*1024)
+#define BFIN_DSUPBANKS 0
+#endif
+
+#endif
+
+/* Level 2 Memory - none */
+
+#define L2_START 0
+#define L2_LENGTH 0
+
+/* Scratch Pad Memory */
+
+#define L1_SCRATCH_START 0xFFB00000
+#define L1_SCRATCH_LENGTH 0x1000
+
+#endif /* _MEM_MAP_533_H_ */
diff --git a/arch/blackfin/mach-bf533/include/mach/portmux.h b/arch/blackfin/mach-bf533/include/mach/portmux.h
new file mode 100644
index 0000000..685a265
--- /dev/null
+++ b/arch/blackfin/mach-bf533/include/mach/portmux.h
@@ -0,0 +1,67 @@
+#ifndef _MACH_PORTMUX_H_
+#define _MACH_PORTMUX_H_
+
+#define MAX_RESOURCES MAX_BLACKFIN_GPIOS
+
+#define P_PPI0_CLK (P_DONTCARE)
+#define P_PPI0_FS1 (P_DONTCARE)
+#define P_PPI0_FS2 (P_DONTCARE)
+#define P_PPI0_FS3 (P_DEFINED | P_IDENT(GPIO_PF3))
+#define P_PPI0_D15 (P_DEFINED | P_IDENT(GPIO_PF4))
+#define P_PPI0_D14 (P_DEFINED | P_IDENT(GPIO_PF5))
+#define P_PPI0_D13 (P_DEFINED | P_IDENT(GPIO_PF6))
+#define P_PPI0_D12 (P_DEFINED | P_IDENT(GPIO_PF7))
+#define P_PPI0_D11 (P_DEFINED | P_IDENT(GPIO_PF8))
+#define P_PPI0_D10 (P_DEFINED | P_IDENT(GPIO_PF9))
+#define P_PPI0_D9 (P_DEFINED | P_IDENT(GPIO_PF10))
+#define P_PPI0_D8 (P_DEFINED | P_IDENT(GPIO_PF11))
+#define P_PPI0_D0 (P_DONTCARE)
+#define P_PPI0_D1 (P_DONTCARE)
+#define P_PPI0_D2 (P_DONTCARE)
+#define P_PPI0_D3 (P_DONTCARE)
+#define P_PPI0_D4 (P_DEFINED | P_IDENT(GPIO_PF15))
+#define P_PPI0_D5 (P_DEFINED | P_IDENT(GPIO_PF14))
+#define P_PPI0_D6 (P_DEFINED | P_IDENT(GPIO_PF13))
+#define P_PPI0_D7 (P_DEFINED | P_IDENT(GPIO_PF12))
+
+#define P_SPORT1_TSCLK (P_DONTCARE)
+#define P_SPORT1_RSCLK (P_DONTCARE)
+#define P_SPORT0_TSCLK (P_DONTCARE)
+#define P_SPORT0_RSCLK (P_DONTCARE)
+#define P_UART0_RX (P_DONTCARE)
+#define P_UART0_TX (P_DONTCARE)
+#define P_SPORT1_DRSEC (P_DONTCARE)
+#define P_SPORT1_RFS (P_DONTCARE)
+#define P_SPORT1_DTPRI (P_DONTCARE)
+#define P_SPORT1_DTSEC (P_DONTCARE)
+#define P_SPORT1_TFS (P_DONTCARE)
+#define P_SPORT1_DRPRI (P_DONTCARE)
+#define P_SPORT0_DRSEC (P_DONTCARE)
+#define P_SPORT0_RFS (P_DONTCARE)
+#define P_SPORT0_DTPRI (P_DONTCARE)
+#define P_SPORT0_DTSEC (P_DONTCARE)
+#define P_SPORT0_TFS (P_DONTCARE)
+#define P_SPORT0_DRPRI (P_DONTCARE)
+
+#define P_SPI0_MOSI (P_DONTCARE)
+#define P_SPI0_MISO (P_DONTCARE)
+#define P_SPI0_SCK (P_DONTCARE)
+#define P_SPI0_SSEL7 (P_DEFINED | P_IDENT(GPIO_PF7))
+#define P_SPI0_SSEL6 (P_DEFINED | P_IDENT(GPIO_PF6))
+#define P_SPI0_SSEL5 (P_DEFINED | P_IDENT(GPIO_PF5))
+#define P_SPI0_SSEL4 (P_DEFINED | P_IDENT(GPIO_PF4))
+#define P_SPI0_SSEL3 (P_DEFINED | P_IDENT(GPIO_PF3))
+#define P_SPI0_SSEL2 (P_DEFINED | P_IDENT(GPIO_PF2))
+#define P_SPI0_SSEL1 (P_DEFINED | P_IDENT(GPIO_PF1))
+#define P_SPI0_SS (P_DEFINED | P_IDENT(GPIO_PF0))
+
+#define P_TMR2 (P_DONTCARE)
+#define P_TMR1 (P_DONTCARE)
+#define P_TMR0 (P_DONTCARE)
+#define P_TMRCLK (P_DEFINED | P_IDENT(GPIO_PF1))
+
+
+
+
+
+#endif /* _MACH_PORTMUX_H_ */