x86, efi stub: Add .reloc section back into image
Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.
Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)
To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.com
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
diff --git a/arch/x86/boot/header.S b/arch/x86/boot/header.S
index 8bbea6a..efe5acf 100644
--- a/arch/x86/boot/header.S
+++ b/arch/x86/boot/header.S
@@ -94,10 +94,10 @@
.section ".bsdata", "a"
bugger_off_msg:
- .ascii "Direct booting from floppy is no longer supported.\r\n"
- .ascii "Please use a boot loader program instead.\r\n"
+ .ascii "Direct floppy boot is not supported. "
+ .ascii "Use a boot loader program instead.\r\n"
.ascii "\n"
- .ascii "Remove disk and press any key to reboot . . .\r\n"
+ .ascii "Remove disk and press any key to reboot ...\r\n"
.byte 0
#ifdef CONFIG_EFI_STUB
@@ -111,7 +111,7 @@
#else
.word 0x8664 # x86-64
#endif
- .word 2 # nr_sections
+ .word 3 # nr_sections
.long 0 # TimeDateStamp
.long 0 # PointerToSymbolTable
.long 1 # NumberOfSymbols
@@ -158,8 +158,8 @@
#else
.quad 0 # ImageBase
#endif
- .long 0x1000 # SectionAlignment
- .long 0x200 # FileAlignment
+ .long 0x20 # SectionAlignment
+ .long 0x20 # FileAlignment
.word 0 # MajorOperatingSystemVersion
.word 0 # MinorOperatingSystemVersion
.word 0 # MajorImageVersion
@@ -200,8 +200,10 @@
# Section table
section_table:
- .ascii ".text"
- .byte 0
+ #
+ # The offset & size fields are filled in by build.c.
+ #
+ .ascii ".setup"
.byte 0
.byte 0
.long 0
@@ -217,9 +219,8 @@
#
# The EFI application loader requires a relocation section
- # because EFI applications must be relocatable. But since
- # we don't need the loader to fixup any relocs for us, we
- # just create an empty (zero-length) .reloc section header.
+ # because EFI applications must be relocatable. The .reloc
+ # offset & size fields are filled in by build.c.
#
.ascii ".reloc"
.byte 0
@@ -233,6 +234,25 @@
.word 0 # NumberOfRelocations
.word 0 # NumberOfLineNumbers
.long 0x42100040 # Characteristics (section flags)
+
+ #
+ # The offset & size fields are filled in by build.c.
+ #
+ .ascii ".text"
+ .byte 0
+ .byte 0
+ .byte 0
+ .long 0
+ .long 0x0 # startup_{32,64}
+ .long 0 # Size of initialized data
+ # on disk
+ .long 0x0 # startup_{32,64}
+ .long 0 # PointerToRelocations
+ .long 0 # PointerToLineNumbers
+ .word 0 # NumberOfRelocations
+ .word 0 # NumberOfLineNumbers
+ .long 0x60500020 # Characteristics (section flags)
+
#endif /* CONFIG_EFI_STUB */
# Kernel attributes; used by setup. This is part 1 of the