mtd: spelling, capitalization, uniformity
Therefor -> Therefore
[Intern], [Internal] -> [INTERN]
[REPLACABLE] -> [REPLACEABLE]
syndrom, syndom -> syndrome
ecc -> ECC
buswith -> buswidth
endianess -> endianness
dont -> don't
occures -> occurs
independend -> independent
wihin -> within
erease -> erase
blockes -> blocks
...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index 0f239e7..877fbbd 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -42,10 +42,10 @@
/* Internal helper for board drivers which need to override command function */
extern void nand_wait_ready(struct mtd_info *mtd);
-/* locks all blockes present in the device */
+/* locks all blocks present in the device */
extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
-/* unlocks specified locked blockes */
+/* unlocks specified locked blocks */
extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len);
/* The maximum number of NAND chips in an array */
@@ -150,7 +150,7 @@
#define NAND_ECC_READ 0
/* Reset Hardware ECC for write */
#define NAND_ECC_WRITE 1
-/* Enable Hardware ECC before syndrom is read back from flash */
+/* Enable Hardware ECC before syndrome is read back from flash */
#define NAND_ECC_READSYN 2
/* Bit mask for flags passed to do_nand_read_ecc */
@@ -163,7 +163,7 @@
*/
/* Chip can not auto increment pages */
#define NAND_NO_AUTOINCR 0x00000001
-/* Buswitdh is 16 bit */
+/* Buswidth is 16 bit */
#define NAND_BUSWIDTH_16 0x00000002
/* Device supports partial programming without padding */
#define NAND_NO_PADDING 0x00000004
@@ -319,26 +319,26 @@
};
/**
- * struct nand_ecc_ctrl - Control structure for ecc
- * @mode: ecc mode
- * @steps: number of ecc steps per page
- * @size: data bytes per ecc step
- * @bytes: ecc bytes per step
- * @total: total number of ecc bytes per page
- * @prepad: padding information for syndrome based ecc generators
- * @postpad: padding information for syndrome based ecc generators
+ * struct nand_ecc_ctrl - Control structure for ECC
+ * @mode: ECC mode
+ * @steps: number of ECC steps per page
+ * @size: data bytes per ECC step
+ * @bytes: ECC bytes per step
+ * @total: total number of ECC bytes per page
+ * @prepad: padding information for syndrome based ECC generators
+ * @postpad: padding information for syndrome based ECC generators
* @layout: ECC layout control struct pointer
- * @priv: pointer to private ecc control data
- * @hwctl: function to control hardware ecc generator. Must only
+ * @priv: pointer to private ECC control data
+ * @hwctl: function to control hardware ECC generator. Must only
* be provided if an hardware ECC is available
- * @calculate: function for ecc calculation or readback from ecc hardware
- * @correct: function for ecc correction, matching to ecc generator (sw/hw)
+ * @calculate: function for ECC calculation or readback from ECC hardware
+ * @correct: function for ECC correction, matching to ECC generator (sw/hw)
* @read_page_raw: function to read a raw page without ECC
* @write_page_raw: function to write a raw page without ECC
- * @read_page: function to read a page according to the ecc generator
+ * @read_page: function to read a page according to the ECC generator
* requirements.
* @read_subpage: function to read parts of the page covered by ECC.
- * @write_page: function to write a page according to the ecc generator
+ * @write_page: function to write a page according to the ECC generator
* requirements.
* @read_oob: function to read chip OOB data
* @write_oob: function to write chip OOB data
@@ -376,8 +376,8 @@
/**
* struct nand_buffers - buffer structure for read/write
- * @ecccalc: buffer for calculated ecc
- * @ecccode: buffer for ecc read from flash
+ * @ecccalc: buffer for calculated ECC
+ * @ecccode: buffer for ECC read from flash
* @databuf: buffer for data - dynamically sized
*
* Do not change the order of buffers. databuf and oobrbuf must be in
@@ -410,7 +410,7 @@
* mtd->oobsize, mtd->writesize and so on.
* @id_data contains the 8 bytes values of NAND_CMD_READID.
* Return with the bus width.
- * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing
+ * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing
* device ready/busy line. If set to NULL no access to
* ready/busy is available and the ready/busy information
* is read from the chip status register.
@@ -418,7 +418,7 @@
* commands to the chip.
* @waitfunc: [REPLACEABLE] hardwarespecific function for wait on
* ready.
- * @ecc: [BOARDSPECIFIC] ecc control ctructure
+ * @ecc: [BOARDSPECIFIC] ECC control structure
* @buffers: buffer structure for read/write
* @hwcontrol: platform-specific hardware control structure
* @ops: oob operation operands
@@ -455,7 +455,7 @@
* non 0 if ONFI supported.
* @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is
* supported, 0 otherwise.
- * @ecclayout: [REPLACEABLE] the default ecc placement scheme
+ * @ecclayout: [REPLACEABLE] the default ECC placement scheme
* @bbt: [INTERN] bad block table pointer
* @bbt_td: [REPLACEABLE] bad block table descriptor for flash
* lookup.
@@ -463,7 +463,7 @@
* @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial
* bad block scan.
* @controller: [REPLACEABLE] a pointer to a hardware controller
- * structure which is shared among multiple independend
+ * structure which is shared among multiple independent
* devices.
* @priv: [OPTIONAL] pointer to private chip date
* @errstat: [OPTIONAL] hardware specific function to perform
@@ -604,7 +604,7 @@
* @chip_delay: R/B delay value in us
* @options: Option flags, e.g. 16bit buswidth
* @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH
- * @ecclayout: ecc layout info structure
+ * @ecclayout: ECC layout info structure
* @part_probe_types: NULL-terminated array of probe types
* @set_parts: platform specific function to set partitions
* @priv: hardware controller specific settings