ARM: OMAP1: Use generic map_io, init_early and init_irq
This allows removing omap hacks for map_io allowing generic
map_io.
Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index a6b1bea..b09dfe6 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -297,63 +297,6 @@
static void __init omap_fsample_init(void)
{
- fsample_init_smc91x();
-
- if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
- BUG();
- gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
-
- omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
- omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
-
- /* Mux pins for keypad */
- omap_cfg_reg(E2_7XX_KBR0);
- omap_cfg_reg(J7_7XX_KBR1);
- omap_cfg_reg(E1_7XX_KBR2);
- omap_cfg_reg(F3_7XX_KBR3);
- omap_cfg_reg(D2_7XX_KBR4);
- omap_cfg_reg(C2_7XX_KBC0);
- omap_cfg_reg(D3_7XX_KBC1);
- omap_cfg_reg(E4_7XX_KBC2);
- omap_cfg_reg(F4_7XX_KBC3);
- omap_cfg_reg(E3_7XX_KBC4);
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
- omap_board_config = fsample_config;
- omap_board_config_size = ARRAY_SIZE(fsample_config);
- omap_serial_init();
- omap_register_i2c_bus(1, 100, NULL, 0);
-}
-
-static void __init omap_fsample_init_irq(void)
-{
- omap1_init_common_hw();
- omap1_init_irq();
-}
-
-/* Only FPGA needs to be mapped here. All others are done with ioremap */
-static struct map_desc omap_fsample_io_desc[] __initdata = {
- {
- .virtual = H2P2_DBG_FPGA_BASE,
- .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
- .length = H2P2_DBG_FPGA_SIZE,
- .type = MT_DEVICE
- },
- {
- .virtual = FSAMPLE_CPLD_BASE,
- .pfn = __phys_to_pfn(FSAMPLE_CPLD_START),
- .length = FSAMPLE_CPLD_SIZE,
- .type = MT_DEVICE
- }
-};
-
-static void __init omap_fsample_map_io(void)
-{
- omap1_map_common_io();
- iotable_init(omap_fsample_io_desc,
- ARRAY_SIZE(omap_fsample_io_desc));
-
/* Early, board-dependent init */
/*
@@ -384,15 +327,68 @@
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
- omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
+ omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF,
+ OMAP7XX_IO_CONF_9);
+
+ fsample_init_smc91x();
+
+ if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+ BUG();
+ gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
+
+ omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
+ omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
+
+ /* Mux pins for keypad */
+ omap_cfg_reg(E2_7XX_KBR0);
+ omap_cfg_reg(J7_7XX_KBR1);
+ omap_cfg_reg(E1_7XX_KBR2);
+ omap_cfg_reg(F3_7XX_KBR3);
+ omap_cfg_reg(D2_7XX_KBR4);
+ omap_cfg_reg(C2_7XX_KBC0);
+ omap_cfg_reg(D3_7XX_KBC1);
+ omap_cfg_reg(E4_7XX_KBC2);
+ omap_cfg_reg(F4_7XX_KBC3);
+ omap_cfg_reg(E3_7XX_KBC4);
+
+ platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ omap_board_config = fsample_config;
+ omap_board_config_size = ARRAY_SIZE(fsample_config);
+ omap_serial_init();
+ omap_register_i2c_bus(1, 100, NULL, 0);
+}
+
+/* Only FPGA needs to be mapped here. All others are done with ioremap */
+static struct map_desc omap_fsample_io_desc[] __initdata = {
+ {
+ .virtual = H2P2_DBG_FPGA_BASE,
+ .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
+ .length = H2P2_DBG_FPGA_SIZE,
+ .type = MT_DEVICE
+ },
+ {
+ .virtual = FSAMPLE_CPLD_BASE,
+ .pfn = __phys_to_pfn(FSAMPLE_CPLD_START),
+ .length = FSAMPLE_CPLD_SIZE,
+ .type = MT_DEVICE
+ }
+};
+
+static void __init omap_fsample_map_io(void)
+{
+ omap15xx_map_io();
+ iotable_init(omap_fsample_io_desc,
+ ARRAY_SIZE(omap_fsample_io_desc));
}
MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")
/* Maintainer: Brian Swetland <swetland@google.com> */
.boot_params = 0x10000100,
.map_io = omap_fsample_map_io,
+ .init_early = omap1_init_early,
.reserve = omap_reserve,
- .init_irq = omap_fsample_init_irq,
+ .init_irq = omap1_init_irq,
.init_machine = omap_fsample_init,
.timer = &omap1_timer,
MACHINE_END