i2c-pxa2xx: Add PCI support for PXA I2C controller
The Sodaville I2C controller is almost the same as found on PXA2xx. The
difference:
- the register are at a different offset
- no slave support
The PCI probe code adds three platform devices which are probed then by
the platform code.
The X86 part also adds dummy clock defines because we don't have HW
clock support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c
index fc2a90e..ab59b7e 100644
--- a/drivers/i2c/busses/i2c-pxa.c
+++ b/drivers/i2c/busses/i2c-pxa.c
@@ -38,6 +38,13 @@
#include <asm/irq.h>
+#ifndef CONFIG_HAVE_CLK
+#define clk_get(dev, id) NULL
+#define clk_put(clk) do { } while (0)
+#define clk_disable(clk) do { } while (0)
+#define clk_enable(clk) do { } while (0)
+#endif
+
struct pxa_reg_layout {
u32 ibmr;
u32 idbr;
@@ -49,6 +56,7 @@
enum pxa_i2c_types {
REGS_PXA2XX,
REGS_PXA3XX,
+ REGS_CE4100,
};
/*
@@ -69,11 +77,19 @@
.isr = 0x18,
.isar = 0x20,
},
+ [REGS_CE4100] = {
+ .ibmr = 0x14,
+ .idbr = 0x0c,
+ .icr = 0x00,
+ .isr = 0x04,
+ /* no isar register */
+ },
};
static const struct platform_device_id i2c_pxa_id_table[] = {
{ "pxa2xx-i2c", REGS_PXA2XX },
{ "pxa3xx-pwri2c", REGS_PXA3XX },
+ { "ce4100-i2c", REGS_CE4100 },
{ },
};
MODULE_DEVICE_TABLE(platform, i2c_pxa_id_table);
@@ -442,7 +458,8 @@
writel(I2C_ISR_INIT, _ISR(i2c));
writel(readl(_ICR(i2c)) & ~ICR_UR, _ICR(i2c));
- writel(i2c->slave_addr, _ISAR(i2c));
+ if (i2c->reg_isar)
+ writel(i2c->slave_addr, _ISAR(i2c));
/* set control register values */
writel(I2C_ICR_INIT | (i2c->fast_mode ? ICR_FM : 0), _ICR(i2c));
@@ -1074,7 +1091,8 @@
i2c->reg_idbr = i2c->reg_base + pxa_reg_layout[i2c_type].idbr;
i2c->reg_icr = i2c->reg_base + pxa_reg_layout[i2c_type].icr;
i2c->reg_isr = i2c->reg_base + pxa_reg_layout[i2c_type].isr;
- i2c->reg_isar = i2c->reg_base + pxa_reg_layout[i2c_type].isar;
+ if (i2c_type != REGS_CE4100)
+ i2c->reg_isar = i2c->reg_base + pxa_reg_layout[i2c_type].isar;
i2c->iobase = res->start;
i2c->iosize = resource_size(res);
@@ -1113,7 +1131,10 @@
i2c->adap.algo_data = i2c;
i2c->adap.dev.parent = &dev->dev;
- ret = i2c_add_numbered_adapter(&i2c->adap);
+ if (i2c_type == REGS_CE4100)
+ ret = i2c_add_adapter(&i2c->adap);
+ else
+ ret = i2c_add_numbered_adapter(&i2c->adap);
if (ret < 0) {
printk(KERN_INFO "I2C: Failed to add bus\n");
goto eadapt;