atl1c: Add AR8151 v2 support and change L0s/L1 routine
Add AR8151 v2.0 Gigabit 1000 support
Change jumbo frame size to 6K
Update L0s/L1 rountine
when link speed is 100M or 1G, set L1 link timer to 4 for l1d_2 and l2c_b2
set L1 link timer to 7 for l2c_b, set L1 link timer to 0xF for others.
Update atl1c_suspend routine
just refactory the function, add atl1c_phy_power_saving routine,
when Wake On Lan enable, this func will be called to save power,
it will reautoneg PHY to 10/100M speed depend on the link
partners link capability.
Update atl1c_configure_des_ring
do not use l2c_b default SRAM configuration.
Signed-off-by: Jie Yang <Jie.Yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/atl1c/atl1c_hw.h b/drivers/net/atl1c/atl1c_hw.h
index 1eeb3ed..3dd6759 100644
--- a/drivers/net/atl1c/atl1c_hw.h
+++ b/drivers/net/atl1c/atl1c_hw.h
@@ -42,7 +42,7 @@
int atl1c_phy_init(struct atl1c_hw *hw);
int atl1c_check_eeprom_exist(struct atl1c_hw *hw);
int atl1c_restart_autoneg(struct atl1c_hw *hw);
-
+int atl1c_phy_power_saving(struct atl1c_hw *hw);
/* register definition */
#define REG_DEVICE_CAP 0x5C
#define DEVICE_CAP_MAX_PAYLOAD_MASK 0x7
@@ -120,6 +120,12 @@
#define REG_PCIE_PHYMISC 0x1000
#define PCIE_PHYMISC_FORCE_RCV_DET 0x4
+#define REG_PCIE_PHYMISC2 0x1004
+#define PCIE_PHYMISC2_SERDES_CDR_MASK 0x3
+#define PCIE_PHYMISC2_SERDES_CDR_SHIFT 16
+#define PCIE_PHYMISC2_SERDES_TH_MASK 0x3
+#define PCIE_PHYMISC2_SERDES_TH_SHIFT 18
+
#define REG_TWSI_DEBUG 0x1108
#define TWSI_DEBUG_DEV_EXIST 0x20000000
@@ -150,24 +156,28 @@
#define PM_CTRL_ASPM_L0S_EN 0x00001000
#define PM_CTRL_CLK_SWH_L1 0x00002000
#define PM_CTRL_CLK_PWM_VER1_1 0x00004000
-#define PM_CTRL_PCIE_RECV 0x00008000
+#define PM_CTRL_RCVR_WT_TIMER 0x00008000
#define PM_CTRL_L1_ENTRY_TIMER_MASK 0xF
#define PM_CTRL_L1_ENTRY_TIMER_SHIFT 16
#define PM_CTRL_PM_REQ_TIMER_MASK 0xF
#define PM_CTRL_PM_REQ_TIMER_SHIFT 20
-#define PM_CTRL_LCKDET_TIMER_MASK 0x3F
+#define PM_CTRL_LCKDET_TIMER_MASK 0xF
#define PM_CTRL_LCKDET_TIMER_SHIFT 24
#define PM_CTRL_EN_BUFS_RX_L0S 0x10000000
#define PM_CTRL_SA_DLY_EN 0x20000000
#define PM_CTRL_MAC_ASPM_CHK 0x40000000
#define PM_CTRL_HOTRST 0x80000000
+#define REG_LTSSM_ID_CTRL 0x12FC
+#define LTSSM_ID_EN_WRO 0x1000
/* Selene Master Control Register */
#define REG_MASTER_CTRL 0x1400
#define MASTER_CTRL_SOFT_RST 0x1
#define MASTER_CTRL_TEST_MODE_MASK 0x3
#define MASTER_CTRL_TEST_MODE_SHIFT 2
#define MASTER_CTRL_BERT_START 0x10
+#define MASTER_CTRL_OOB_DIS_OFF 0x40
+#define MASTER_CTRL_SA_TIMER_EN 0x80
#define MASTER_CTRL_MTIMER_EN 0x100
#define MASTER_CTRL_MANUAL_INT 0x200
#define MASTER_CTRL_TX_ITIMER_EN 0x400
@@ -220,6 +230,12 @@
GPHY_CTRL_PWDOWN_HW |\
GPHY_CTRL_PHY_IDDQ)
+#define GPHY_CTRL_POWER_SAVING ( \
+ GPHY_CTRL_SEL_ANA_RST |\
+ GPHY_CTRL_HIB_EN |\
+ GPHY_CTRL_HIB_PULSE |\
+ GPHY_CTRL_PWDOWN_HW |\
+ GPHY_CTRL_PHY_IDDQ)
/* Block IDLE Status Register */
#define REG_IDLE_STATUS 0x1410
#define IDLE_STATUS_MASK 0x00FF
@@ -287,6 +303,14 @@
#define SERDES_LOCK_DETECT 0x1 /* SerDes lock detected. This signal
* comes from Analog SerDes */
#define SERDES_LOCK_DETECT_EN 0x2 /* 1: Enable SerDes Lock detect function */
+#define SERDES_LOCK_STS_SELFB_PLL_SHIFT 0xE
+#define SERDES_LOCK_STS_SELFB_PLL_MASK 0x3
+#define SERDES_OVCLK_18_25 0x0
+#define SERDES_OVCLK_12_18 0x1
+#define SERDES_OVCLK_0_4 0x2
+#define SERDES_OVCLK_4_12 0x3
+#define SERDES_MAC_CLK_SLOWDOWN 0x20000
+#define SERDES_PYH_CLK_SLOWDOWN 0x40000
/* MAC Control Register */
#define REG_MAC_CTRL 0x1480
@@ -693,6 +717,21 @@
#define REG_MAC_TX_STATUS_BIN 0x1760
#define REG_MAC_TX_STATUS_END 0x17c0
+#define REG_CLK_GATING_CTRL 0x1814
+#define CLK_GATING_DMAW_EN 0x0001
+#define CLK_GATING_DMAR_EN 0x0002
+#define CLK_GATING_TXQ_EN 0x0004
+#define CLK_GATING_RXQ_EN 0x0008
+#define CLK_GATING_TXMAC_EN 0x0010
+#define CLK_GATING_RXMAC_EN 0x0020
+
+#define CLK_GATING_EN_ALL (CLK_GATING_DMAW_EN |\
+ CLK_GATING_DMAR_EN |\
+ CLK_GATING_TXQ_EN |\
+ CLK_GATING_RXQ_EN |\
+ CLK_GATING_TXMAC_EN|\
+ CLK_GATING_RXMAC_EN)
+
/* DEBUG ADDR */
#define REG_DEBUG_DATA0 0x1900
#define REG_DEBUG_DATA1 0x1904
@@ -734,6 +773,10 @@
#define MII_PHYSID1 0x02
#define MII_PHYSID2 0x03
+#define L1D_MPW_PHYID1 0xD01C /* V7 */
+#define L1D_MPW_PHYID2 0xD01D /* V1-V6 */
+#define L1D_MPW_PHYID3 0xD01E /* V8 */
+
/* Autoneg Advertisement Register */
#define MII_ADVERTISE 0x04