ARM: at91: dt: switch to standard GPIO flag defines.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index ba1205d..85e9c5e 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -68,7 +68,7 @@
slot@0 {
reg = <0>;
bus-width = <4>;
- cd-gpios = <&pioD 10 0>;
+ cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
};
};
@@ -81,8 +81,8 @@
slot@0 {
reg = <0>;
bus-width = <4>;
- cd-gpios = <&pioD 11 0>;
- wp-gpios = <&pioD 29 0>;
+ cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
};
};
@@ -139,8 +139,8 @@
usb0: ohci@00700000 {
status = "okay";
num-ports = <2>;
- atmel,vbus-gpio = <&pioD 1 1
- &pioD 3 1>;
+ atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
+ &pioD 3 GPIO_ACTIVE_LOW>;
};
usb1: ehci@00800000 {
@@ -153,19 +153,19 @@
d8 {
label = "d8";
- gpios = <&pioD 30 0>;
+ gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
d6 {
label = "d6";
- gpios = <&pioD 0 1>;
+ gpios = <&pioD 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "nand-disk";
};
d7 {
label = "d7";
- gpios = <&pioD 31 1>;
+ gpios = <&pioD 31 GPIO_ACTIVE_LOW>;
linux,default-trigger = "mmc0";
};
};
@@ -175,45 +175,45 @@
left_click {
label = "left_click";
- gpios = <&pioB 6 1>;
+ gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
linux,code = <272>;
gpio-key,wakeup;
};
right_click {
label = "right_click";
- gpios = <&pioB 7 1>;
+ gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
linux,code = <273>;
gpio-key,wakeup;
};
left {
label = "Joystick Left";
- gpios = <&pioB 14 1>;
+ gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
linux,code = <105>;
};
right {
label = "Joystick Right";
- gpios = <&pioB 15 1>;
+ gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
linux,code = <106>;
};
up {
label = "Joystick Up";
- gpios = <&pioB 16 1>;
+ gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
linux,code = <103>;
};
down {
label = "Joystick Down";
- gpios = <&pioB 17 1>;
+ gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
linux,code = <108>;
};
enter {
label = "Joystick Press";
- gpios = <&pioB 18 1>;
+ gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
linux,code = <28>;
};
};