i2c: Bus drivers return -Errno not -1
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c
index 93bf87d..3d75256 100644
--- a/drivers/i2c/busses/i2c-ali15x3.c
+++ b/drivers/i2c/busses/i2c-ali15x3.c
@@ -282,7 +282,7 @@
dev_err(&adap->dev, "SMBus reset failed! (0x%02x) - "
"controller or device on bus is probably hung\n",
temp);
- return -1;
+ return -EBUSY;
}
} else {
/* check and clear done bit */
@@ -304,12 +304,12 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
- result = -1;
+ result = -ETIMEDOUT;
dev_err(&adap->dev, "SMBus Timeout!\n");
}
if (temp & ALI15X3_STS_TERM) {
- result = -1;
+ result = -EIO;
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
}
@@ -320,7 +320,7 @@
This means that bus collisions go unreported.
*/
if (temp & ALI15X3_STS_COLL) {
- result = -1;
+ result = -ENXIO;
dev_dbg(&adap->dev,
"Error: no response or bus collision ADD=%02x\n",
inb_p(SMBHSTADD));
@@ -328,7 +328,7 @@
/* haven't ever seen this */
if (temp & ALI15X3_STS_DEV) {
- result = -1;
+ result = -EIO;
dev_err(&adap->dev, "Error: device error\n");
}
dev_dbg(&adap->dev, "Transaction (post): STS=%02x, CNT=%02x, CMD=%02x, "
@@ -338,7 +338,7 @@
return result;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 ali15x3_access(struct i2c_adapter * adap, u16 addr,
unsigned short flags, char read_write, u8 command,
int size, union i2c_smbus_data * data)
@@ -364,7 +364,7 @@
switch (size) {
case I2C_SMBUS_PROC_CALL:
dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n");
- return -1;
+ return -EOPNOTSUPP;
case I2C_SMBUS_QUICK:
outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
SMBHSTADD);
@@ -421,8 +421,9 @@
outb_p(size, SMBHSTCNT); /* output command */
- if (ali15x3_transaction(adap)) /* Error in transaction */
- return -1;
+ temp = ali15x3_transaction(adap);
+ if (temp)
+ return temp;
if ((read_write == I2C_SMBUS_WRITE) || (size == ALI15X3_QUICK))
return 0;