mtd: at91: add dt parameters for Atmel PMECC
Add DT support for PMECC parameters.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index a200695..d555421 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -3,7 +3,9 @@
Required properties:
- compatible : "atmel,at91rm9200-nand".
- reg : should specify localbus address and size used for the chip,
- and if availlable the ECC.
+ and hardware ECC controller if available.
+ If the hardware ECC is PMECC, it should contain address and size for
+ PMECC, PMECC Error Location controller and ROM which has lookup tables.
- atmel,nand-addr-offset : offset for the address latch.
- atmel,nand-cmd-offset : offset for the command latch.
- #address-cells, #size-cells : Must be present if the device has sub-nodes
@@ -16,6 +18,15 @@
- nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
"soft_bch".
+- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware.
+ Only supported by at91sam9x5 or later sam9 product.
+- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC
+ Controller. Supported values are: 2, 4, 8, 12, 24.
+- atmel,pmecc-sector-size : sector size for ECC computation. Supported values
+ are: 512, 1024.
+- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM
+ for different sector size. First one is for sector size 512, the next is for
+ sector size 1024.
- nand-bus-width : 8 or 16 bus width if not present 8
- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
@@ -39,3 +50,30 @@
...
};
};
+
+/* for PMECC supported chips */
+nand0: nand@40000000 {
+ compatible = "atmel,at91rm9200-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = < 0x40000000 0x10000000 /* bus addr & size */
+ 0xffffe000 0x00000600 /* PMECC addr & size */
+ 0xffffe600 0x00000200 /* PMECC ERRLOC addr & size */
+ 0x00100000 0x00100000 /* ROM addr & size */
+ >;
+ atmel,nand-addr-offset = <21>; /* ale */
+ atmel,nand-cmd-offset = <22>; /* cle */
+ nand-on-flash-bbt;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc; /* enable PMECC */
+ atmel,pmecc-cap = <2>;
+ atmel,pmecc-sector-size = <512>;
+ atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
+ gpios = <&pioD 5 0 /* rdy */
+ &pioD 4 0 /* nce */
+ 0 /* cd */
+ >;
+ partition@0 {
+ ...
+ };
+};