|  | /* | 
|  | * Davicom DM9601 USB 1.1 10/100Mbps ethernet devices | 
|  | * | 
|  | * Peter Korsgaard <jacmet@sunsite.dk> | 
|  | * | 
|  | * This file is licensed under the terms of the GNU General Public License | 
|  | * version 2.  This program is licensed "as is" without any warranty of any | 
|  | * kind, whether express or implied. | 
|  | */ | 
|  |  | 
|  | //#define DEBUG | 
|  |  | 
|  | #include <linux/module.h> | 
|  | #include <linux/sched.h> | 
|  | #include <linux/stddef.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/netdevice.h> | 
|  | #include <linux/etherdevice.h> | 
|  | #include <linux/ethtool.h> | 
|  | #include <linux/mii.h> | 
|  | #include <linux/usb.h> | 
|  | #include <linux/crc32.h> | 
|  | #include <linux/usb/usbnet.h> | 
|  | #include <linux/slab.h> | 
|  |  | 
|  | /* datasheet: | 
|  | http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf | 
|  | */ | 
|  |  | 
|  | /* control requests */ | 
|  | #define DM_READ_REGS	0x00 | 
|  | #define DM_WRITE_REGS	0x01 | 
|  | #define DM_READ_MEMS	0x02 | 
|  | #define DM_WRITE_REG	0x03 | 
|  | #define DM_WRITE_MEMS	0x05 | 
|  | #define DM_WRITE_MEM	0x07 | 
|  |  | 
|  | /* registers */ | 
|  | #define DM_NET_CTRL	0x00 | 
|  | #define DM_RX_CTRL	0x05 | 
|  | #define DM_SHARED_CTRL	0x0b | 
|  | #define DM_SHARED_ADDR	0x0c | 
|  | #define DM_SHARED_DATA	0x0d	/* low + high */ | 
|  | #define DM_PHY_ADDR	0x10	/* 6 bytes */ | 
|  | #define DM_MCAST_ADDR	0x16	/* 8 bytes */ | 
|  | #define DM_GPR_CTRL	0x1e | 
|  | #define DM_GPR_DATA	0x1f | 
|  |  | 
|  | #define DM_MAX_MCAST	64 | 
|  | #define DM_MCAST_SIZE	8 | 
|  | #define DM_EEPROM_LEN	256 | 
|  | #define DM_TX_OVERHEAD	2	/* 2 byte header */ | 
|  | #define DM_RX_OVERHEAD	7	/* 3 byte header + 4 byte crc tail */ | 
|  | #define DM_TIMEOUT	1000 | 
|  |  | 
|  |  | 
|  | static int dm_read(struct usbnet *dev, u8 reg, u16 length, void *data) | 
|  | { | 
|  | void *buf; | 
|  | int err = -ENOMEM; | 
|  |  | 
|  | netdev_dbg(dev->net, "dm_read() reg=0x%02x length=%d\n", reg, length); | 
|  |  | 
|  | buf = kmalloc(length, GFP_KERNEL); | 
|  | if (!buf) | 
|  | goto out; | 
|  |  | 
|  | err = usb_control_msg(dev->udev, | 
|  | usb_rcvctrlpipe(dev->udev, 0), | 
|  | DM_READ_REGS, | 
|  | USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, | 
|  | 0, reg, buf, length, USB_CTRL_SET_TIMEOUT); | 
|  | if (err == length) | 
|  | memcpy(data, buf, length); | 
|  | else if (err >= 0) | 
|  | err = -EINVAL; | 
|  | kfree(buf); | 
|  |  | 
|  | out: | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value) | 
|  | { | 
|  | return dm_read(dev, reg, 1, value); | 
|  | } | 
|  |  | 
|  | static int dm_write(struct usbnet *dev, u8 reg, u16 length, void *data) | 
|  | { | 
|  | void *buf = NULL; | 
|  | int err = -ENOMEM; | 
|  |  | 
|  | netdev_dbg(dev->net, "dm_write() reg=0x%02x, length=%d\n", reg, length); | 
|  |  | 
|  | if (data) { | 
|  | buf = kmemdup(data, length, GFP_KERNEL); | 
|  | if (!buf) | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | err = usb_control_msg(dev->udev, | 
|  | usb_sndctrlpipe(dev->udev, 0), | 
|  | DM_WRITE_REGS, | 
|  | USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE, | 
|  | 0, reg, buf, length, USB_CTRL_SET_TIMEOUT); | 
|  | kfree(buf); | 
|  | if (err >= 0 && err < length) | 
|  | err = -EINVAL; | 
|  | out: | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int dm_write_reg(struct usbnet *dev, u8 reg, u8 value) | 
|  | { | 
|  | netdev_dbg(dev->net, "dm_write_reg() reg=0x%02x, value=0x%02x\n", | 
|  | reg, value); | 
|  | return usb_control_msg(dev->udev, | 
|  | usb_sndctrlpipe(dev->udev, 0), | 
|  | DM_WRITE_REG, | 
|  | USB_DIR_OUT | USB_TYPE_VENDOR |USB_RECIP_DEVICE, | 
|  | value, reg, NULL, 0, USB_CTRL_SET_TIMEOUT); | 
|  | } | 
|  |  | 
|  | static void dm_write_async_callback(struct urb *urb) | 
|  | { | 
|  | struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context; | 
|  | int status = urb->status; | 
|  |  | 
|  | if (status < 0) | 
|  | printk(KERN_DEBUG "dm_write_async_callback() failed with %d\n", | 
|  | status); | 
|  |  | 
|  | kfree(req); | 
|  | usb_free_urb(urb); | 
|  | } | 
|  |  | 
|  | static void dm_write_async_helper(struct usbnet *dev, u8 reg, u8 value, | 
|  | u16 length, void *data) | 
|  | { | 
|  | struct usb_ctrlrequest *req; | 
|  | struct urb *urb; | 
|  | int status; | 
|  |  | 
|  | urb = usb_alloc_urb(0, GFP_ATOMIC); | 
|  | if (!urb) { | 
|  | netdev_err(dev->net, "Error allocating URB in dm_write_async_helper!\n"); | 
|  | return; | 
|  | } | 
|  |  | 
|  | req = kmalloc(sizeof(struct usb_ctrlrequest), GFP_ATOMIC); | 
|  | if (!req) { | 
|  | netdev_err(dev->net, "Failed to allocate memory for control request\n"); | 
|  | usb_free_urb(urb); | 
|  | return; | 
|  | } | 
|  |  | 
|  | req->bRequestType = USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE; | 
|  | req->bRequest = length ? DM_WRITE_REGS : DM_WRITE_REG; | 
|  | req->wValue = cpu_to_le16(value); | 
|  | req->wIndex = cpu_to_le16(reg); | 
|  | req->wLength = cpu_to_le16(length); | 
|  |  | 
|  | usb_fill_control_urb(urb, dev->udev, | 
|  | usb_sndctrlpipe(dev->udev, 0), | 
|  | (void *)req, data, length, | 
|  | dm_write_async_callback, req); | 
|  |  | 
|  | status = usb_submit_urb(urb, GFP_ATOMIC); | 
|  | if (status < 0) { | 
|  | netdev_err(dev->net, "Error submitting the control message: status=%d\n", | 
|  | status); | 
|  | kfree(req); | 
|  | usb_free_urb(urb); | 
|  | } | 
|  | } | 
|  |  | 
|  | static void dm_write_async(struct usbnet *dev, u8 reg, u16 length, void *data) | 
|  | { | 
|  | netdev_dbg(dev->net, "dm_write_async() reg=0x%02x length=%d\n", reg, length); | 
|  |  | 
|  | dm_write_async_helper(dev, reg, 0, length, data); | 
|  | } | 
|  |  | 
|  | static void dm_write_reg_async(struct usbnet *dev, u8 reg, u8 value) | 
|  | { | 
|  | netdev_dbg(dev->net, "dm_write_reg_async() reg=0x%02x value=0x%02x\n", | 
|  | reg, value); | 
|  |  | 
|  | dm_write_async_helper(dev, reg, value, 0, NULL); | 
|  | } | 
|  |  | 
|  | static int dm_read_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 *value) | 
|  | { | 
|  | int ret, i; | 
|  |  | 
|  | mutex_lock(&dev->phy_mutex); | 
|  |  | 
|  | dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg); | 
|  | dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0xc : 0x4); | 
|  |  | 
|  | for (i = 0; i < DM_TIMEOUT; i++) { | 
|  | u8 tmp; | 
|  |  | 
|  | udelay(1); | 
|  | ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp); | 
|  | if (ret < 0) | 
|  | goto out; | 
|  |  | 
|  | /* ready */ | 
|  | if ((tmp & 1) == 0) | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (i == DM_TIMEOUT) { | 
|  | netdev_err(dev->net, "%s read timed out!\n", phy ? "phy" : "eeprom"); | 
|  | ret = -EIO; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | dm_write_reg(dev, DM_SHARED_CTRL, 0x0); | 
|  | ret = dm_read(dev, DM_SHARED_DATA, 2, value); | 
|  |  | 
|  | netdev_dbg(dev->net, "read shared %d 0x%02x returned 0x%04x, %d\n", | 
|  | phy, reg, *value, ret); | 
|  |  | 
|  | out: | 
|  | mutex_unlock(&dev->phy_mutex); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int dm_write_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 value) | 
|  | { | 
|  | int ret, i; | 
|  |  | 
|  | mutex_lock(&dev->phy_mutex); | 
|  |  | 
|  | ret = dm_write(dev, DM_SHARED_DATA, 2, &value); | 
|  | if (ret < 0) | 
|  | goto out; | 
|  |  | 
|  | dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg); | 
|  | dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0x1a : 0x12); | 
|  |  | 
|  | for (i = 0; i < DM_TIMEOUT; i++) { | 
|  | u8 tmp; | 
|  |  | 
|  | udelay(1); | 
|  | ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp); | 
|  | if (ret < 0) | 
|  | goto out; | 
|  |  | 
|  | /* ready */ | 
|  | if ((tmp & 1) == 0) | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (i == DM_TIMEOUT) { | 
|  | netdev_err(dev->net, "%s write timed out!\n", phy ? "phy" : "eeprom"); | 
|  | ret = -EIO; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | dm_write_reg(dev, DM_SHARED_CTRL, 0x0); | 
|  |  | 
|  | out: | 
|  | mutex_unlock(&dev->phy_mutex); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int dm_read_eeprom_word(struct usbnet *dev, u8 offset, void *value) | 
|  | { | 
|  | return dm_read_shared_word(dev, 0, offset, value); | 
|  | } | 
|  |  | 
|  |  | 
|  |  | 
|  | static int dm9601_get_eeprom_len(struct net_device *dev) | 
|  | { | 
|  | return DM_EEPROM_LEN; | 
|  | } | 
|  |  | 
|  | static int dm9601_get_eeprom(struct net_device *net, | 
|  | struct ethtool_eeprom *eeprom, u8 * data) | 
|  | { | 
|  | struct usbnet *dev = netdev_priv(net); | 
|  | __le16 *ebuf = (__le16 *) data; | 
|  | int i; | 
|  |  | 
|  | /* access is 16bit */ | 
|  | if ((eeprom->offset % 2) || (eeprom->len % 2)) | 
|  | return -EINVAL; | 
|  |  | 
|  | for (i = 0; i < eeprom->len / 2; i++) { | 
|  | if (dm_read_eeprom_word(dev, eeprom->offset / 2 + i, | 
|  | &ebuf[i]) < 0) | 
|  | return -EINVAL; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int dm9601_mdio_read(struct net_device *netdev, int phy_id, int loc) | 
|  | { | 
|  | struct usbnet *dev = netdev_priv(netdev); | 
|  |  | 
|  | __le16 res; | 
|  |  | 
|  | if (phy_id) { | 
|  | netdev_dbg(dev->net, "Only internal phy supported\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | dm_read_shared_word(dev, 1, loc, &res); | 
|  |  | 
|  | netdev_dbg(dev->net, | 
|  | "dm9601_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n", | 
|  | phy_id, loc, le16_to_cpu(res)); | 
|  |  | 
|  | return le16_to_cpu(res); | 
|  | } | 
|  |  | 
|  | static void dm9601_mdio_write(struct net_device *netdev, int phy_id, int loc, | 
|  | int val) | 
|  | { | 
|  | struct usbnet *dev = netdev_priv(netdev); | 
|  | __le16 res = cpu_to_le16(val); | 
|  |  | 
|  | if (phy_id) { | 
|  | netdev_dbg(dev->net, "Only internal phy supported\n"); | 
|  | return; | 
|  | } | 
|  |  | 
|  | netdev_dbg(dev->net, "dm9601_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n", | 
|  | phy_id, loc, val); | 
|  |  | 
|  | dm_write_shared_word(dev, 1, loc, res); | 
|  | } | 
|  |  | 
|  | static void dm9601_get_drvinfo(struct net_device *net, | 
|  | struct ethtool_drvinfo *info) | 
|  | { | 
|  | /* Inherit standard device info */ | 
|  | usbnet_get_drvinfo(net, info); | 
|  | info->eedump_len = DM_EEPROM_LEN; | 
|  | } | 
|  |  | 
|  | static u32 dm9601_get_link(struct net_device *net) | 
|  | { | 
|  | struct usbnet *dev = netdev_priv(net); | 
|  |  | 
|  | return mii_link_ok(&dev->mii); | 
|  | } | 
|  |  | 
|  | static int dm9601_ioctl(struct net_device *net, struct ifreq *rq, int cmd) | 
|  | { | 
|  | struct usbnet *dev = netdev_priv(net); | 
|  |  | 
|  | return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL); | 
|  | } | 
|  |  | 
|  | static const struct ethtool_ops dm9601_ethtool_ops = { | 
|  | .get_drvinfo	= dm9601_get_drvinfo, | 
|  | .get_link	= dm9601_get_link, | 
|  | .get_msglevel	= usbnet_get_msglevel, | 
|  | .set_msglevel	= usbnet_set_msglevel, | 
|  | .get_eeprom_len	= dm9601_get_eeprom_len, | 
|  | .get_eeprom	= dm9601_get_eeprom, | 
|  | .get_settings	= usbnet_get_settings, | 
|  | .set_settings	= usbnet_set_settings, | 
|  | .nway_reset	= usbnet_nway_reset, | 
|  | }; | 
|  |  | 
|  | static void dm9601_set_multicast(struct net_device *net) | 
|  | { | 
|  | struct usbnet *dev = netdev_priv(net); | 
|  | /* We use the 20 byte dev->data for our 8 byte filter buffer | 
|  | * to avoid allocating memory that is tricky to free later */ | 
|  | u8 *hashes = (u8 *) & dev->data; | 
|  | u8 rx_ctl = 0x31; | 
|  |  | 
|  | memset(hashes, 0x00, DM_MCAST_SIZE); | 
|  | hashes[DM_MCAST_SIZE - 1] |= 0x80;	/* broadcast address */ | 
|  |  | 
|  | if (net->flags & IFF_PROMISC) { | 
|  | rx_ctl |= 0x02; | 
|  | } else if (net->flags & IFF_ALLMULTI || | 
|  | netdev_mc_count(net) > DM_MAX_MCAST) { | 
|  | rx_ctl |= 0x04; | 
|  | } else if (!netdev_mc_empty(net)) { | 
|  | struct netdev_hw_addr *ha; | 
|  |  | 
|  | netdev_for_each_mc_addr(ha, net) { | 
|  | u32 crc = ether_crc(ETH_ALEN, ha->addr) >> 26; | 
|  | hashes[crc >> 3] |= 1 << (crc & 0x7); | 
|  | } | 
|  | } | 
|  |  | 
|  | dm_write_async(dev, DM_MCAST_ADDR, DM_MCAST_SIZE, hashes); | 
|  | dm_write_reg_async(dev, DM_RX_CTRL, rx_ctl); | 
|  | } | 
|  |  | 
|  | static void __dm9601_set_mac_address(struct usbnet *dev) | 
|  | { | 
|  | dm_write_async(dev, DM_PHY_ADDR, ETH_ALEN, dev->net->dev_addr); | 
|  | } | 
|  |  | 
|  | static int dm9601_set_mac_address(struct net_device *net, void *p) | 
|  | { | 
|  | struct sockaddr *addr = p; | 
|  | struct usbnet *dev = netdev_priv(net); | 
|  |  | 
|  | if (!is_valid_ether_addr(addr->sa_data)) { | 
|  | dev_err(&net->dev, "not setting invalid mac address %pM\n", | 
|  | addr->sa_data); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | memcpy(net->dev_addr, addr->sa_data, net->addr_len); | 
|  | __dm9601_set_mac_address(dev); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct net_device_ops dm9601_netdev_ops = { | 
|  | .ndo_open		= usbnet_open, | 
|  | .ndo_stop		= usbnet_stop, | 
|  | .ndo_start_xmit		= usbnet_start_xmit, | 
|  | .ndo_tx_timeout		= usbnet_tx_timeout, | 
|  | .ndo_change_mtu		= usbnet_change_mtu, | 
|  | .ndo_validate_addr	= eth_validate_addr, | 
|  | .ndo_do_ioctl 		= dm9601_ioctl, | 
|  | .ndo_set_rx_mode	= dm9601_set_multicast, | 
|  | .ndo_set_mac_address	= dm9601_set_mac_address, | 
|  | }; | 
|  |  | 
|  | static int dm9601_bind(struct usbnet *dev, struct usb_interface *intf) | 
|  | { | 
|  | int ret; | 
|  | u8 mac[ETH_ALEN]; | 
|  |  | 
|  | ret = usbnet_get_endpoints(dev, intf); | 
|  | if (ret) | 
|  | goto out; | 
|  |  | 
|  | dev->net->netdev_ops = &dm9601_netdev_ops; | 
|  | dev->net->ethtool_ops = &dm9601_ethtool_ops; | 
|  | dev->net->hard_header_len += DM_TX_OVERHEAD; | 
|  | dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len; | 
|  | dev->rx_urb_size = dev->net->mtu + ETH_HLEN + DM_RX_OVERHEAD; | 
|  |  | 
|  | dev->mii.dev = dev->net; | 
|  | dev->mii.mdio_read = dm9601_mdio_read; | 
|  | dev->mii.mdio_write = dm9601_mdio_write; | 
|  | dev->mii.phy_id_mask = 0x1f; | 
|  | dev->mii.reg_num_mask = 0x1f; | 
|  |  | 
|  | /* reset */ | 
|  | dm_write_reg(dev, DM_NET_CTRL, 1); | 
|  | udelay(20); | 
|  |  | 
|  | /* read MAC */ | 
|  | if (dm_read(dev, DM_PHY_ADDR, ETH_ALEN, mac) < 0) { | 
|  | printk(KERN_ERR "Error reading MAC address\n"); | 
|  | ret = -ENODEV; | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Overwrite the auto-generated address only with good ones. | 
|  | */ | 
|  | if (is_valid_ether_addr(mac)) | 
|  | memcpy(dev->net->dev_addr, mac, ETH_ALEN); | 
|  | else { | 
|  | printk(KERN_WARNING | 
|  | "dm9601: No valid MAC address in EEPROM, using %pM\n", | 
|  | dev->net->dev_addr); | 
|  | __dm9601_set_mac_address(dev); | 
|  | } | 
|  |  | 
|  | /* power up phy */ | 
|  | dm_write_reg(dev, DM_GPR_CTRL, 1); | 
|  | dm_write_reg(dev, DM_GPR_DATA, 0); | 
|  |  | 
|  | /* receive broadcast packets */ | 
|  | dm9601_set_multicast(dev->net); | 
|  |  | 
|  | dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET); | 
|  | dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, | 
|  | ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP); | 
|  | mii_nway_restart(&dev->mii); | 
|  |  | 
|  | out: | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int dm9601_rx_fixup(struct usbnet *dev, struct sk_buff *skb) | 
|  | { | 
|  | u8 status; | 
|  | int len; | 
|  |  | 
|  | /* format: | 
|  | b1: rx status | 
|  | b2: packet length (incl crc) low | 
|  | b3: packet length (incl crc) high | 
|  | b4..n-4: packet data | 
|  | bn-3..bn: ethernet crc | 
|  | */ | 
|  |  | 
|  | if (unlikely(skb->len < DM_RX_OVERHEAD)) { | 
|  | dev_err(&dev->udev->dev, "unexpected tiny rx frame\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | status = skb->data[0]; | 
|  | len = (skb->data[1] | (skb->data[2] << 8)) - 4; | 
|  |  | 
|  | if (unlikely(status & 0xbf)) { | 
|  | if (status & 0x01) dev->net->stats.rx_fifo_errors++; | 
|  | if (status & 0x02) dev->net->stats.rx_crc_errors++; | 
|  | if (status & 0x04) dev->net->stats.rx_frame_errors++; | 
|  | if (status & 0x20) dev->net->stats.rx_missed_errors++; | 
|  | if (status & 0x90) dev->net->stats.rx_length_errors++; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | skb_pull(skb, 3); | 
|  | skb_trim(skb, len); | 
|  |  | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static struct sk_buff *dm9601_tx_fixup(struct usbnet *dev, struct sk_buff *skb, | 
|  | gfp_t flags) | 
|  | { | 
|  | int len; | 
|  |  | 
|  | /* format: | 
|  | b1: packet length low | 
|  | b2: packet length high | 
|  | b3..n: packet data | 
|  | */ | 
|  |  | 
|  | len = skb->len; | 
|  |  | 
|  | if (skb_headroom(skb) < DM_TX_OVERHEAD) { | 
|  | struct sk_buff *skb2; | 
|  |  | 
|  | skb2 = skb_copy_expand(skb, DM_TX_OVERHEAD, 0, flags); | 
|  | dev_kfree_skb_any(skb); | 
|  | skb = skb2; | 
|  | if (!skb) | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | __skb_push(skb, DM_TX_OVERHEAD); | 
|  |  | 
|  | /* usbnet adds padding if length is a multiple of packet size | 
|  | if so, adjust length value in header */ | 
|  | if ((skb->len % dev->maxpacket) == 0) | 
|  | len++; | 
|  |  | 
|  | skb->data[0] = len; | 
|  | skb->data[1] = len >> 8; | 
|  |  | 
|  | return skb; | 
|  | } | 
|  |  | 
|  | static void dm9601_status(struct usbnet *dev, struct urb *urb) | 
|  | { | 
|  | int link; | 
|  | u8 *buf; | 
|  |  | 
|  | /* format: | 
|  | b0: net status | 
|  | b1: tx status 1 | 
|  | b2: tx status 2 | 
|  | b3: rx status | 
|  | b4: rx overflow | 
|  | b5: rx count | 
|  | b6: tx count | 
|  | b7: gpr | 
|  | */ | 
|  |  | 
|  | if (urb->actual_length < 8) | 
|  | return; | 
|  |  | 
|  | buf = urb->transfer_buffer; | 
|  |  | 
|  | link = !!(buf[0] & 0x40); | 
|  | if (netif_carrier_ok(dev->net) != link) { | 
|  | if (link) { | 
|  | netif_carrier_on(dev->net); | 
|  | usbnet_defer_kevent (dev, EVENT_LINK_RESET); | 
|  | } | 
|  | else | 
|  | netif_carrier_off(dev->net); | 
|  | netdev_dbg(dev->net, "Link Status is: %d\n", link); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int dm9601_link_reset(struct usbnet *dev) | 
|  | { | 
|  | struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET }; | 
|  |  | 
|  | mii_check_media(&dev->mii, 1, 1); | 
|  | mii_ethtool_gset(&dev->mii, &ecmd); | 
|  |  | 
|  | netdev_dbg(dev->net, "link_reset() speed: %u duplex: %d\n", | 
|  | ethtool_cmd_speed(&ecmd), ecmd.duplex); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct driver_info dm9601_info = { | 
|  | .description	= "Davicom DM9601 USB Ethernet", | 
|  | .flags		= FLAG_ETHER | FLAG_LINK_INTR, | 
|  | .bind		= dm9601_bind, | 
|  | .rx_fixup	= dm9601_rx_fixup, | 
|  | .tx_fixup	= dm9601_tx_fixup, | 
|  | .status		= dm9601_status, | 
|  | .link_reset	= dm9601_link_reset, | 
|  | .reset		= dm9601_link_reset, | 
|  | }; | 
|  |  | 
|  | static const struct usb_device_id products[] = { | 
|  | { | 
|  | USB_DEVICE(0x07aa, 0x9601),	/* Corega FEther USB-TXC */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0a46, 0x9601),	/* Davicom USB-100 */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0a46, 0x6688),	/* ZT6688 USB NIC */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0a46, 0x0268),	/* ShanTou ST268 USB NIC */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0a46, 0x8515),	/* ADMtek ADM8515 USB NIC */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0a47, 0x9601),	/* Hirose USB-100 */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0fe6, 0x8101),	/* DM9601 USB to Fast Ethernet Adapter */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0fe6, 0x9700),	/* DM9601 USB to Fast Ethernet Adapter */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | { | 
|  | USB_DEVICE(0x0a46, 0x9000),	/* DM9000E */ | 
|  | .driver_info = (unsigned long)&dm9601_info, | 
|  | }, | 
|  | {},			// END | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(usb, products); | 
|  |  | 
|  | static struct usb_driver dm9601_driver = { | 
|  | .name = "dm9601", | 
|  | .id_table = products, | 
|  | .probe = usbnet_probe, | 
|  | .disconnect = usbnet_disconnect, | 
|  | .suspend = usbnet_suspend, | 
|  | .resume = usbnet_resume, | 
|  | .disable_hub_initiated_lpm = 1, | 
|  | }; | 
|  |  | 
|  | module_usb_driver(dm9601_driver); | 
|  |  | 
|  | MODULE_AUTHOR("Peter Korsgaard <jacmet@sunsite.dk>"); | 
|  | MODULE_DESCRIPTION("Davicom DM9601 USB 1.1 ethernet devices"); | 
|  | MODULE_LICENSE("GPL"); |