microblaze: Prefer to use pr_XXX instead of printk(KERN_XX)
Fix reset.c, timer.c, setup.c file.
Signed-off-by: Michal Simek <monstr@monstr.eu>
diff --git a/arch/microblaze/kernel/reset.c b/arch/microblaze/kernel/reset.c
index 6ce60fb..2e5079a 100644
--- a/arch/microblaze/kernel/reset.c
+++ b/arch/microblaze/kernel/reset.c
@@ -26,14 +26,14 @@
"hard-reset-gpios", 0);
if (!gpio_is_valid(handle)) {
- printk(KERN_INFO "Skipping unavailable RESET gpio %d (%s)\n",
+ pr_info("Skipping unavailable RESET gpio %d (%s)\n",
handle, "reset");
return;
}
ret = gpio_request(handle, "reset");
if (ret < 0) {
- printk(KERN_INFO "GPIO pin is already allocated\n");
+ pr_info("GPIO pin is already allocated\n");
return;
}
@@ -50,7 +50,7 @@
/* Setup output direction */
gpio_set_value(handle, 0);
- printk(KERN_INFO "RESET: Registered gpio device: %d, current val: %d\n",
+ pr_info("RESET: Registered gpio device: %d, current val: %d\n",
handle, reset_val);
return;
err:
@@ -76,7 +76,7 @@
void machine_restart(char *cmd)
{
- printk(KERN_NOTICE "Machine restart...\n");
+ pr_notice("Machine restart...\n");
gpio_system_reset();
while (1)
;
@@ -84,21 +84,21 @@
void machine_shutdown(void)
{
- printk(KERN_NOTICE "Machine shutdown...\n");
+ pr_notice("Machine shutdown...\n");
while (1)
;
}
void machine_halt(void)
{
- printk(KERN_NOTICE "Machine halt...\n");
+ pr_notice("Machine halt...\n");
while (1)
;
}
void machine_power_off(void)
{
- printk(KERN_NOTICE "Machine power off...\n");
+ pr_notice("Machine power off...\n");
while (1)
;
}
diff --git a/arch/microblaze/kernel/setup.c b/arch/microblaze/kernel/setup.c
index 9dbc9ec..954348f 100644
--- a/arch/microblaze/kernel/setup.c
+++ b/arch/microblaze/kernel/setup.c
@@ -69,7 +69,7 @@
xilinx_pci_init();
#if defined(CONFIG_SELFMOD_INTC) || defined(CONFIG_SELFMOD_TIMER)
- printk(KERN_NOTICE "Self modified code enable\n");
+ pr_notice("Self modified code enable\n");
#endif
#ifdef CONFIG_VT
diff --git a/arch/microblaze/kernel/timer.c b/arch/microblaze/kernel/timer.c
index edd3f83..aec5020 100644
--- a/arch/microblaze/kernel/timer.c
+++ b/arch/microblaze/kernel/timer.c
@@ -116,21 +116,21 @@
{
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
- printk(KERN_INFO "%s: periodic\n", __func__);
+ pr_info("%s: periodic\n", __func__);
microblaze_timer0_start_periodic(freq_div_hz);
break;
case CLOCK_EVT_MODE_ONESHOT:
- printk(KERN_INFO "%s: oneshot\n", __func__);
+ pr_info("%s: oneshot\n", __func__);
break;
case CLOCK_EVT_MODE_UNUSED:
- printk(KERN_INFO "%s: unused\n", __func__);
+ pr_info("%s: unused\n", __func__);
break;
case CLOCK_EVT_MODE_SHUTDOWN:
- printk(KERN_INFO "%s: shutdown\n", __func__);
+ pr_info("%s: shutdown\n", __func__);
microblaze_timer0_stop();
break;
case CLOCK_EVT_MODE_RESUME:
- printk(KERN_INFO "%s: resume\n", __func__);
+ pr_info("%s: resume\n", __func__);
break;
}
}
@@ -274,14 +274,14 @@
timer_num = be32_to_cpup(of_get_property(timer,
"xlnx,one-timer-only", NULL));
if (timer_num) {
- printk(KERN_EMERG "Please enable two timers in HW\n");
+ pr_emerg("Please enable two timers in HW\n");
BUG();
}
#ifdef CONFIG_SELFMOD_TIMER
selfmod_function((int *) arr_func, timer_baseaddr);
#endif
- printk(KERN_INFO "%s #0 at 0x%08x, irq=%d\n",
+ pr_info("%s #0 at 0x%08x, irq=%d\n",
timer->name, timer_baseaddr, irq);
/* If there is clock-frequency property than use it */