e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 1c98dfa..68aa174 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -533,7 +533,7 @@
mac->autoneg_failed = 1;
return 0;
}
- e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n");
+ e_dbg("NOT Rx'ing /C/, disable AutoNeg and force link.\n");
/* Disable auto-negotiation in the TXCW register */
ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
@@ -556,7 +556,7 @@
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
*/
- e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ e_dbg("Rx'ing /C/, enable AutoNeg and stop forcing link.\n");
ew32(TXCW, mac->txcw);
ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
@@ -598,7 +598,7 @@
mac->autoneg_failed = 1;
return 0;
}
- e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n");
+ e_dbg("NOT Rx'ing /C/, disable AutoNeg and force link.\n");
/* Disable auto-negotiation in the TXCW register */
ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
@@ -621,7 +621,7 @@
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
*/
- e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n");
+ e_dbg("Rx'ing /C/, enable AutoNeg and stop forcing link.\n");
ew32(TXCW, mac->txcw);
ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
@@ -800,9 +800,9 @@
* The possible values of the "fc" parameter are:
* 0: Flow control is completely disabled
* 1: Rx flow control is enabled (we can receive pause frames,
- * but not send pause frames).
+ * but not send pause frames).
* 2: Tx flow control is enabled (we can send pause frames but we
- * do not support receiving pause frames).
+ * do not support receiving pause frames).
* 3: Both Rx and Tx flow control (symmetric) are enabled.
*/
switch (hw->fc.current_mode) {
@@ -1031,9 +1031,9 @@
* The possible values of the "fc" parameter are:
* 0: Flow control is completely disabled
* 1: Rx flow control is enabled (we can receive pause
- * frames but not send pause frames).
+ * frames but not send pause frames).
* 2: Tx flow control is enabled (we can send pause frames
- * frames but we do not receive pause frames).
+ * frames but we do not receive pause frames).
* 3: Both Rx and Tx flow control (symmetric) is enabled.
* other: No other values should be possible at this point.
*/
@@ -1189,7 +1189,7 @@
} else {
hw->fc.current_mode = e1000_fc_rx_pause;
e_dbg("Flow Control = "
- "RX PAUSE frames only.\r\n");
+ "Rx PAUSE frames only.\r\n");
}
}
/*