| /* |
| * opp2xxx.h - macros for old-style OMAP2xxx "OPP" definitions |
| * |
| * Copyright (C) 2005-2009 Texas Instruments, Inc. |
| * Copyright (C) 2004-2009 Nokia Corporation |
| * |
| * Richard Woodruff <r-woodruff2@ti.com> |
| * |
| * The OMAP2 processor can be run at several discrete 'PRCM configurations'. |
| * These configurations are characterized by voltage and speed for clocks. |
| * The device is only validated for certain combinations. One way to express |
| * these combinations is via the 'ratio's' which the clocks operate with |
| * respect to each other. These ratio sets are for a given voltage/DPLL |
| * setting. All configurations can be described by a DPLL setting and a ratio |
| * There are 3 ratio sets for the 2430 and X ratio sets for 2420. |
| * |
| * 2430 differs from 2420 in that there are no more phase synchronizers used. |
| * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs |
| * 2430 (iva2.1, NOdsp, mdm) |
| * |
| * XXX Missing voltage data. |
| * |
| * THe format described in this file is deprecated. Once a reasonable |
| * OPP API exists, the data in this file should be converted to use it. |
| * |
| * This is technically part of the OMAP2xxx clock code. |
| */ |
| |
| #ifndef __ARCH_ARM_MACH_OMAP2_OPP2XXX_H |
| #define __ARCH_ARM_MACH_OMAP2_OPP2XXX_H |
| |
| /** |
| * struct prcm_config - define clock rates on a per-OPP basis (24xx) |
| * |
| * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. |
| * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,CM_CLKSEL_DSP |
| * CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL CM_CLKSEL2_PLL, CM_CLKSEL_MDM |
| * |
| * This is deprecated. As soon as we have a decent OPP API, we should |
| * move all this stuff to it. |
| */ |
| struct prcm_config { |
| unsigned long xtal_speed; /* crystal rate */ |
| unsigned long dpll_speed; /* dpll: out*xtal*M/(N-1)table_recalc */ |
| unsigned long mpu_speed; /* speed of MPU */ |
| unsigned long cm_clksel_mpu; /* mpu divider */ |
| unsigned long cm_clksel_dsp; /* dsp+iva1 div(2420), iva2.1(2430) */ |
| unsigned long cm_clksel_gfx; /* gfx dividers */ |
| unsigned long cm_clksel1_core; /* major subsystem dividers */ |
| unsigned long cm_clksel1_pll; /* m,n */ |
| unsigned long cm_clksel2_pll; /* dpllx1 or x2 out */ |
| unsigned long cm_clksel_mdm; /* modem dividers 2430 only */ |
| unsigned long base_sdrc_rfr; /* base refresh timing for a set */ |
| unsigned char flags; |
| }; |
| |
| |
| /* Core fields for cm_clksel, not ratio governed */ |
| #define RX_CLKSEL_DSS1 (0x10 << 8) |
| #define RX_CLKSEL_DSS2 (0x0 << 13) |
| #define RX_CLKSEL_SSI (0x5 << 20) |
| |
| /*------------------------------------------------------------------------- |
| * Voltage/DPLL ratios |
| *-------------------------------------------------------------------------*/ |
| |
| /* 2430 Ratio's, 2430-Ratio Config 1 */ |
| #define R1_CLKSEL_L3 (4 << 0) |
| #define R1_CLKSEL_L4 (2 << 5) |
| #define R1_CLKSEL_USB (4 << 25) |
| #define R1_CM_CLKSEL1_CORE_VAL (R1_CLKSEL_USB | RX_CLKSEL_SSI | \ |
| RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ |
| R1_CLKSEL_L4 | R1_CLKSEL_L3) |
| #define R1_CLKSEL_MPU (2 << 0) |
| #define R1_CM_CLKSEL_MPU_VAL R1_CLKSEL_MPU |
| #define R1_CLKSEL_DSP (2 << 0) |
| #define R1_CLKSEL_DSP_IF (2 << 5) |
| #define R1_CM_CLKSEL_DSP_VAL (R1_CLKSEL_DSP | R1_CLKSEL_DSP_IF) |
| #define R1_CLKSEL_GFX (2 << 0) |
| #define R1_CM_CLKSEL_GFX_VAL R1_CLKSEL_GFX |
| #define R1_CLKSEL_MDM (4 << 0) |
| #define R1_CM_CLKSEL_MDM_VAL R1_CLKSEL_MDM |
| |
| /* 2430-Ratio Config 2 */ |
| #define R2_CLKSEL_L3 (6 << 0) |
| #define R2_CLKSEL_L4 (2 << 5) |
| #define R2_CLKSEL_USB (2 << 25) |
| #define R2_CM_CLKSEL1_CORE_VAL (R2_CLKSEL_USB | RX_CLKSEL_SSI | \ |
| RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ |
| R2_CLKSEL_L4 | R2_CLKSEL_L3) |
| #define R2_CLKSEL_MPU (2 << 0) |
| #define R2_CM_CLKSEL_MPU_VAL R2_CLKSEL_MPU |
| #define R2_CLKSEL_DSP (2 << 0) |
| #define R2_CLKSEL_DSP_IF (3 << 5) |
| #define R2_CM_CLKSEL_DSP_VAL (R2_CLKSEL_DSP | R2_CLKSEL_DSP_IF) |
| #define R2_CLKSEL_GFX (2 << 0) |
| #define R2_CM_CLKSEL_GFX_VAL R2_CLKSEL_GFX |
| #define R2_CLKSEL_MDM (6 << 0) |
| #define R2_CM_CLKSEL_MDM_VAL R2_CLKSEL_MDM |
| |
| /* 2430-Ratio Bootm (BYPASS) */ |
| #define RB_CLKSEL_L3 (1 << 0) |
| #define RB_CLKSEL_L4 (1 << 5) |
| #define RB_CLKSEL_USB (1 << 25) |
| #define RB_CM_CLKSEL1_CORE_VAL (RB_CLKSEL_USB | RX_CLKSEL_SSI | \ |
| RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ |
| RB_CLKSEL_L4 | RB_CLKSEL_L3) |
| #define RB_CLKSEL_MPU (1 << 0) |
| #define RB_CM_CLKSEL_MPU_VAL RB_CLKSEL_MPU |
| #define RB_CLKSEL_DSP (1 << 0) |
| #define RB_CLKSEL_DSP_IF (1 << 5) |
| #define RB_CM_CLKSEL_DSP_VAL (RB_CLKSEL_DSP | RB_CLKSEL_DSP_IF) |
| #define RB_CLKSEL_GFX (1 << 0) |
| #define RB_CM_CLKSEL_GFX_VAL RB_CLKSEL_GFX |
| #define RB_CLKSEL_MDM (1 << 0) |
| #define RB_CM_CLKSEL_MDM_VAL RB_CLKSEL_MDM |
| |
| /* 2420 Ratio Equivalents */ |
| #define RXX_CLKSEL_VLYNQ (0x12 << 15) |
| #define RXX_CLKSEL_SSI (0x8 << 20) |
| |
| /* 2420-PRCM III 532MHz core */ |
| #define RIII_CLKSEL_L3 (4 << 0) /* 133MHz */ |
| #define RIII_CLKSEL_L4 (2 << 5) /* 66.5MHz */ |
| #define RIII_CLKSEL_USB (4 << 25) /* 33.25MHz */ |
| #define RIII_CM_CLKSEL1_CORE_VAL (RIII_CLKSEL_USB | RXX_CLKSEL_SSI | \ |
| RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \ |
| RX_CLKSEL_DSS1 | RIII_CLKSEL_L4 | \ |
| RIII_CLKSEL_L3) |
| #define RIII_CLKSEL_MPU (2 << 0) /* 266MHz */ |
| #define RIII_CM_CLKSEL_MPU_VAL RIII_CLKSEL_MPU |
| #define RIII_CLKSEL_DSP (3 << 0) /* c5x - 177.3MHz */ |
| #define RIII_CLKSEL_DSP_IF (2 << 5) /* c5x - 88.67MHz */ |
| #define RIII_SYNC_DSP (1 << 7) /* Enable sync */ |
| #define RIII_CLKSEL_IVA (6 << 8) /* iva1 - 88.67MHz */ |
| #define RIII_SYNC_IVA (1 << 13) /* Enable sync */ |
| #define RIII_CM_CLKSEL_DSP_VAL (RIII_SYNC_IVA | RIII_CLKSEL_IVA | \ |
| RIII_SYNC_DSP | RIII_CLKSEL_DSP_IF | \ |
| RIII_CLKSEL_DSP) |
| #define RIII_CLKSEL_GFX (2 << 0) /* 66.5MHz */ |
| #define RIII_CM_CLKSEL_GFX_VAL RIII_CLKSEL_GFX |
| |
| /* 2420-PRCM II 600MHz core */ |
| #define RII_CLKSEL_L3 (6 << 0) /* 100MHz */ |
| #define RII_CLKSEL_L4 (2 << 5) /* 50MHz */ |
| #define RII_CLKSEL_USB (2 << 25) /* 50MHz */ |
| #define RII_CM_CLKSEL1_CORE_VAL (RII_CLKSEL_USB | RXX_CLKSEL_SSI | \ |
| RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \ |
| RX_CLKSEL_DSS1 | RII_CLKSEL_L4 | \ |
| RII_CLKSEL_L3) |
| #define RII_CLKSEL_MPU (2 << 0) /* 300MHz */ |
| #define RII_CM_CLKSEL_MPU_VAL RII_CLKSEL_MPU |
| #define RII_CLKSEL_DSP (3 << 0) /* c5x - 200MHz */ |
| #define RII_CLKSEL_DSP_IF (2 << 5) /* c5x - 100MHz */ |
| #define RII_SYNC_DSP (0 << 7) /* Bypass sync */ |
| #define RII_CLKSEL_IVA (3 << 8) /* iva1 - 200MHz */ |
| #define RII_SYNC_IVA (0 << 13) /* Bypass sync */ |
| #define RII_CM_CLKSEL_DSP_VAL (RII_SYNC_IVA | RII_CLKSEL_IVA | \ |
| RII_SYNC_DSP | RII_CLKSEL_DSP_IF | \ |
| RII_CLKSEL_DSP) |
| #define RII_CLKSEL_GFX (2 << 0) /* 50MHz */ |
| #define RII_CM_CLKSEL_GFX_VAL RII_CLKSEL_GFX |
| |
| /* 2420-PRCM I 660MHz core */ |
| #define RI_CLKSEL_L3 (4 << 0) /* 165MHz */ |
| #define RI_CLKSEL_L4 (2 << 5) /* 82.5MHz */ |
| #define RI_CLKSEL_USB (4 << 25) /* 41.25MHz */ |
| #define RI_CM_CLKSEL1_CORE_VAL (RI_CLKSEL_USB | \ |
| RXX_CLKSEL_SSI | RXX_CLKSEL_VLYNQ | \ |
| RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ |
| RI_CLKSEL_L4 | RI_CLKSEL_L3) |
| #define RI_CLKSEL_MPU (2 << 0) /* 330MHz */ |
| #define RI_CM_CLKSEL_MPU_VAL RI_CLKSEL_MPU |
| #define RI_CLKSEL_DSP (3 << 0) /* c5x - 220MHz */ |
| #define RI_CLKSEL_DSP_IF (2 << 5) /* c5x - 110MHz */ |
| #define RI_SYNC_DSP (1 << 7) /* Activate sync */ |
| #define RI_CLKSEL_IVA (4 << 8) /* iva1 - 165MHz */ |
| #define RI_SYNC_IVA (0 << 13) /* Bypass sync */ |
| #define RI_CM_CLKSEL_DSP_VAL (RI_SYNC_IVA | RI_CLKSEL_IVA | \ |
| RI_SYNC_DSP | RI_CLKSEL_DSP_IF | \ |
| RI_CLKSEL_DSP) |
| #define RI_CLKSEL_GFX (1 << 0) /* 165MHz */ |
| #define RI_CM_CLKSEL_GFX_VAL RI_CLKSEL_GFX |
| |
| /* 2420-PRCM VII (boot) */ |
| #define RVII_CLKSEL_L3 (1 << 0) |
| #define RVII_CLKSEL_L4 (1 << 5) |
| #define RVII_CLKSEL_DSS1 (1 << 8) |
| #define RVII_CLKSEL_DSS2 (0 << 13) |
| #define RVII_CLKSEL_VLYNQ (1 << 15) |
| #define RVII_CLKSEL_SSI (1 << 20) |
| #define RVII_CLKSEL_USB (1 << 25) |
| |
| #define RVII_CM_CLKSEL1_CORE_VAL (RVII_CLKSEL_USB | RVII_CLKSEL_SSI | \ |
| RVII_CLKSEL_VLYNQ | \ |
| RVII_CLKSEL_DSS2 | RVII_CLKSEL_DSS1 | \ |
| RVII_CLKSEL_L4 | RVII_CLKSEL_L3) |
| |
| #define RVII_CLKSEL_MPU (1 << 0) /* all divide by 1 */ |
| #define RVII_CM_CLKSEL_MPU_VAL RVII_CLKSEL_MPU |
| |
| #define RVII_CLKSEL_DSP (1 << 0) |
| #define RVII_CLKSEL_DSP_IF (1 << 5) |
| #define RVII_SYNC_DSP (0 << 7) |
| #define RVII_CLKSEL_IVA (1 << 8) |
| #define RVII_SYNC_IVA (0 << 13) |
| #define RVII_CM_CLKSEL_DSP_VAL (RVII_SYNC_IVA | RVII_CLKSEL_IVA | \ |
| RVII_SYNC_DSP | RVII_CLKSEL_DSP_IF | \ |
| RVII_CLKSEL_DSP) |
| |
| #define RVII_CLKSEL_GFX (1 << 0) |
| #define RVII_CM_CLKSEL_GFX_VAL RVII_CLKSEL_GFX |
| |
| /*------------------------------------------------------------------------- |
| * 2430 Target modes: Along with each configuration the CPU has several |
| * modes which goes along with them. Modes mainly are the addition of |
| * describe DPLL combinations to go along with a ratio. |
| *-------------------------------------------------------------------------*/ |
| |
| /* Hardware governed */ |
| #define MX_48M_SRC (0 << 3) |
| #define MX_54M_SRC (0 << 5) |
| #define MX_APLLS_CLIKIN_12 (3 << 23) |
| #define MX_APLLS_CLIKIN_13 (2 << 23) |
| #define MX_APLLS_CLIKIN_19_2 (0 << 23) |
| |
| /* |
| * 2430 - standalone, 2*ref*M/(n+1), M/N is for exactness not relock speed |
| * #5a (ratio1) baseport-target, target DPLL = 266*2 = 532MHz |
| */ |
| #define M5A_DPLL_MULT_12 (133 << 12) |
| #define M5A_DPLL_DIV_12 (5 << 8) |
| #define M5A_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M5A_DPLL_DIV_12 | M5A_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| #define M5A_DPLL_MULT_13 (61 << 12) |
| #define M5A_DPLL_DIV_13 (2 << 8) |
| #define M5A_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M5A_DPLL_DIV_13 | M5A_DPLL_MULT_13 | \ |
| MX_APLLS_CLIKIN_13) |
| #define M5A_DPLL_MULT_19 (55 << 12) |
| #define M5A_DPLL_DIV_19 (3 << 8) |
| #define M5A_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M5A_DPLL_DIV_19 | M5A_DPLL_MULT_19 | \ |
| MX_APLLS_CLIKIN_19_2) |
| /* #5b (ratio1) target DPLL = 200*2 = 400MHz */ |
| #define M5B_DPLL_MULT_12 (50 << 12) |
| #define M5B_DPLL_DIV_12 (2 << 8) |
| #define M5B_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M5B_DPLL_DIV_12 | M5B_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| #define M5B_DPLL_MULT_13 (200 << 12) |
| #define M5B_DPLL_DIV_13 (12 << 8) |
| |
| #define M5B_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M5B_DPLL_DIV_13 | M5B_DPLL_MULT_13 | \ |
| MX_APLLS_CLIKIN_13) |
| #define M5B_DPLL_MULT_19 (125 << 12) |
| #define M5B_DPLL_DIV_19 (31 << 8) |
| #define M5B_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M5B_DPLL_DIV_19 | M5B_DPLL_MULT_19 | \ |
| MX_APLLS_CLIKIN_19_2) |
| /* |
| * #4 (ratio2), DPLL = 399*2 = 798MHz, L3=133MHz |
| */ |
| #define M4_DPLL_MULT_12 (133 << 12) |
| #define M4_DPLL_DIV_12 (3 << 8) |
| #define M4_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M4_DPLL_DIV_12 | M4_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| |
| #define M4_DPLL_MULT_13 (399 << 12) |
| #define M4_DPLL_DIV_13 (12 << 8) |
| #define M4_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M4_DPLL_DIV_13 | M4_DPLL_MULT_13 | \ |
| MX_APLLS_CLIKIN_13) |
| |
| #define M4_DPLL_MULT_19 (145 << 12) |
| #define M4_DPLL_DIV_19 (6 << 8) |
| #define M4_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M4_DPLL_DIV_19 | M4_DPLL_MULT_19 | \ |
| MX_APLLS_CLIKIN_19_2) |
| |
| /* |
| * #3 (ratio2) baseport-target, target DPLL = 330*2 = 660MHz |
| */ |
| #define M3_DPLL_MULT_12 (55 << 12) |
| #define M3_DPLL_DIV_12 (1 << 8) |
| #define M3_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M3_DPLL_DIV_12 | M3_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| #define M3_DPLL_MULT_13 (76 << 12) |
| #define M3_DPLL_DIV_13 (2 << 8) |
| #define M3_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M3_DPLL_DIV_13 | M3_DPLL_MULT_13 | \ |
| MX_APLLS_CLIKIN_13) |
| #define M3_DPLL_MULT_19 (17 << 12) |
| #define M3_DPLL_DIV_19 (0 << 8) |
| #define M3_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M3_DPLL_DIV_19 | M3_DPLL_MULT_19 | \ |
| MX_APLLS_CLIKIN_19_2) |
| |
| /* |
| * #2 (ratio1) DPLL = 330*2 = 660MHz, L3=165MHz |
| */ |
| #define M2_DPLL_MULT_12 (55 << 12) |
| #define M2_DPLL_DIV_12 (1 << 8) |
| #define M2_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M2_DPLL_DIV_12 | M2_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| |
| /* Speed changes - Used 658.7MHz instead of 660MHz for LP-Refresh M=76 N=2, |
| * relock time issue */ |
| /* Core frequency changed from 330/165 to 329/164 MHz*/ |
| #define M2_DPLL_MULT_13 (76 << 12) |
| #define M2_DPLL_DIV_13 (2 << 8) |
| #define M2_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M2_DPLL_DIV_13 | M2_DPLL_MULT_13 | \ |
| MX_APLLS_CLIKIN_13) |
| |
| #define M2_DPLL_MULT_19 (17 << 12) |
| #define M2_DPLL_DIV_19 (0 << 8) |
| #define M2_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| M2_DPLL_DIV_19 | M2_DPLL_MULT_19 | \ |
| MX_APLLS_CLIKIN_19_2) |
| |
| /* boot (boot) */ |
| #define MB_DPLL_MULT (1 << 12) |
| #define MB_DPLL_DIV (0 << 8) |
| #define MB_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MB_DPLL_DIV | MB_DPLL_MULT | \ |
| MX_APLLS_CLIKIN_12) |
| |
| #define MB_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MB_DPLL_DIV | MB_DPLL_MULT | \ |
| MX_APLLS_CLIKIN_13) |
| |
| #define MB_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MB_DPLL_DIV | MB_DPLL_MULT | \ |
| MX_APLLS_CLIKIN_19) |
| |
| /* |
| * 2430 - chassis (sedna) |
| * 165 (ratio1) same as above #2 |
| * 150 (ratio1) |
| * 133 (ratio2) same as above #4 |
| * 110 (ratio2) same as above #3 |
| * 104 (ratio2) |
| * boot (boot) |
| */ |
| |
| /* PRCM I target DPLL = 2*330MHz = 660MHz */ |
| #define MI_DPLL_MULT_12 (55 << 12) |
| #define MI_DPLL_DIV_12 (1 << 8) |
| #define MI_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MI_DPLL_DIV_12 | MI_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| |
| /* |
| * 2420 Equivalent - mode registers |
| * PRCM II , target DPLL = 2*300MHz = 600MHz |
| */ |
| #define MII_DPLL_MULT_12 (50 << 12) |
| #define MII_DPLL_DIV_12 (1 << 8) |
| #define MII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MII_DPLL_DIV_12 | MII_DPLL_MULT_12 | \ |
| MX_APLLS_CLIKIN_12) |
| #define MII_DPLL_MULT_13 (300 << 12) |
| #define MII_DPLL_DIV_13 (12 << 8) |
| #define MII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MII_DPLL_DIV_13 | MII_DPLL_MULT_13 | \ |
| MX_APLLS_CLIKIN_13) |
| |
| /* PRCM III target DPLL = 2*266 = 532MHz*/ |
| #define MIII_DPLL_MULT_12 (133 << 12) |
| #define MIII_DPLL_DIV_12 (5 << 8) |
| #define MIII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MIII_DPLL_DIV_12 | \ |
| MIII_DPLL_MULT_12 | MX_APLLS_CLIKIN_12) |
| #define MIII_DPLL_MULT_13 (266 << 12) |
| #define MIII_DPLL_DIV_13 (12 << 8) |
| #define MIII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ |
| MIII_DPLL_DIV_13 | \ |
| MIII_DPLL_MULT_13 | MX_APLLS_CLIKIN_13) |
| |
| /* PRCM VII (boot bypass) */ |
| #define MVII_CM_CLKSEL1_PLL_12_VAL MB_CM_CLKSEL1_PLL_12_VAL |
| #define MVII_CM_CLKSEL1_PLL_13_VAL MB_CM_CLKSEL1_PLL_13_VAL |
| |
| /* High and low operation value */ |
| #define MX_CLKSEL2_PLL_2x_VAL (2 << 0) |
| #define MX_CLKSEL2_PLL_1x_VAL (1 << 0) |
| |
| /* MPU speed defines */ |
| #define S12M 12000000 |
| #define S13M 13000000 |
| #define S19M 19200000 |
| #define S26M 26000000 |
| #define S100M 100000000 |
| #define S133M 133000000 |
| #define S150M 150000000 |
| #define S164M 164000000 |
| #define S165M 165000000 |
| #define S199M 199000000 |
| #define S200M 200000000 |
| #define S266M 266000000 |
| #define S300M 300000000 |
| #define S329M 329000000 |
| #define S330M 330000000 |
| #define S399M 399000000 |
| #define S400M 400000000 |
| #define S532M 532000000 |
| #define S600M 600000000 |
| #define S658M 658000000 |
| #define S660M 660000000 |
| #define S798M 798000000 |
| |
| |
| extern const struct prcm_config omap2420_rate_table[]; |
| |
| #ifdef CONFIG_SOC_OMAP2430 |
| extern const struct prcm_config omap2430_rate_table[]; |
| #else |
| #define omap2430_rate_table NULL |
| #endif |
| extern const struct prcm_config *rate_table; |
| extern const struct prcm_config *curr_prcm_set; |
| |
| #endif |