Merge branch 'imx-features-for-arnd' of git://git.pengutronix.de/git/imx/linux-2.6 into imx/devel
Conflicts:
arch/arm/mach-mx5/clock-mx51-mx53.c
arch/arm/mach-mx5/devices-imx53.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 975b5dd..3bf38c8 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1272,6 +1272,32 @@
This workaround defines cpu_relax() as smp_mb(), preventing correctly
written polling loops from denying visibility of updates to memory.
+config ARM_ERRATA_364296
+ bool "ARM errata: Possible cache data corruption with hit-under-miss enabled"
+ depends on CPU_V6 && !SMP
+ help
+ This options enables the workaround for the 364296 ARM1136
+ r0p2 erratum (possible cache data corruption with
+ hit-under-miss enabled). It sets the undocumented bit 31 in
+ the auxiliary control register and the FI bit in the control
+ register, thus disabling hit-under-miss without putting the
+ processor into full low interrupt latency mode. ARM11MPCore
+ is not affected.
+
+config ARM_ERRATA_764369
+ bool "ARM errata: Data cache line maintenance operation by MVA may not succeed"
+ depends on CPU_V7 && SMP
+ help
+ This option enables the workaround for erratum 764369
+ affecting Cortex-A9 MPCore with two or more processors (all
+ current revisions). Under certain timing circumstances, a data
+ cache line maintenance operation by MVA targeting an Inner
+ Shareable memory region may fail to proceed up to either the
+ Point of Coherency or to the Point of Unification of the
+ system. This workaround adds a DSB instruction before the
+ relevant cache maintenance functions and sets a specific bit
+ in the diagnostic control register of the SCU.
+
endmenu
source "arch/arm/common/Kconfig"
diff --git a/arch/arm/boot/compressed/mmcif-sh7372.c b/arch/arm/boot/compressed/mmcif-sh7372.c
index b6f61d9..672ae95 100644
--- a/arch/arm/boot/compressed/mmcif-sh7372.c
+++ b/arch/arm/boot/compressed/mmcif-sh7372.c
@@ -82,7 +82,7 @@
/* Disable clock to MMC hardware block */
- __raw_writel(__raw_readl(SMSTPCR3) & (1 << 12), SMSTPCR3);
+ __raw_writel(__raw_readl(SMSTPCR3) | (1 << 12), SMSTPCR3);
mmc_update_progress(MMC_PROGRESS_DONE);
}
diff --git a/arch/arm/boot/compressed/sdhi-sh7372.c b/arch/arm/boot/compressed/sdhi-sh7372.c
index d403a8b..d279294 100644
--- a/arch/arm/boot/compressed/sdhi-sh7372.c
+++ b/arch/arm/boot/compressed/sdhi-sh7372.c
@@ -85,7 +85,7 @@
goto err;
/* Disable clock to SDHI1 hardware block */
- __raw_writel(__raw_readl(SMSTPCR3) & (1 << 13), SMSTPCR3);
+ __raw_writel(__raw_readl(SMSTPCR3) | (1 << 13), SMSTPCR3);
mmc_update_progress(MMC_PROGRESS_DONE);
diff --git a/arch/arm/boot/dts/tegra-harmony.dts b/arch/arm/boot/dts/tegra-harmony.dts
index 4c05334..e581866 100644
--- a/arch/arm/boot/dts/tegra-harmony.dts
+++ b/arch/arm/boot/dts/tegra-harmony.dts
@@ -57,14 +57,14 @@
};
sdhci@c8000200 {
- gpios = <&gpio 69 0>, /* cd, gpio PI5 */
- <&gpio 57 0>, /* wp, gpio PH1 */
- <&gpio 155 0>; /* power, gpio PT3 */
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 155 0>; /* gpio PT3 */
};
sdhci@c8000600 {
- gpios = <&gpio 58 0>, /* cd, gpio PH2 */
- <&gpio 59 0>, /* wp, gpio PH3 */
- <&gpio 70 0>; /* power, gpio PI6 */
+ cd-gpios = <&gpio 58 0>; /* gpio PH2 */
+ wp-gpios = <&gpio 59 0>; /* gpio PH3 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
};
};
diff --git a/arch/arm/boot/dts/tegra-seaboard.dts b/arch/arm/boot/dts/tegra-seaboard.dts
index 1940cae..64cedca 100644
--- a/arch/arm/boot/dts/tegra-seaboard.dts
+++ b/arch/arm/boot/dts/tegra-seaboard.dts
@@ -21,8 +21,8 @@
};
sdhci@c8000400 {
- gpios = <&gpio 69 0>, /* cd, gpio PI5 */
- <&gpio 57 0>, /* wp, gpio PH1 */
- <&gpio 70 0>; /* power, gpio PI6 */
+ cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+ wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+ power-gpios = <&gpio 70 0>; /* gpio PI6 */
};
};
diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index db2cb7d..6ee781b 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -26,6 +26,7 @@
CONFIG_MACH_MX28EVK=y
CONFIG_MACH_STMP378X_DEVB=y
CONFIG_MACH_TX28=y
+CONFIG_MACH_M28EVK=y
# CONFIG_ARM_THUMB is not set
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
diff --git a/arch/arm/include/asm/futex.h b/arch/arm/include/asm/futex.h
index 8c73900..253cc86 100644
--- a/arch/arm/include/asm/futex.h
+++ b/arch/arm/include/asm/futex.h
@@ -25,17 +25,17 @@
#ifdef CONFIG_SMP
-#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg) \
+#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg) \
smp_mb(); \
__asm__ __volatile__( \
- "1: ldrex %1, [%2]\n" \
+ "1: ldrex %1, [%3]\n" \
" " insn "\n" \
- "2: strex %1, %0, [%2]\n" \
- " teq %1, #0\n" \
+ "2: strex %2, %0, [%3]\n" \
+ " teq %2, #0\n" \
" bne 1b\n" \
" mov %0, #0\n" \
- __futex_atomic_ex_table("%4") \
- : "=&r" (ret), "=&r" (oldval) \
+ __futex_atomic_ex_table("%5") \
+ : "=&r" (ret), "=&r" (oldval), "=&r" (tmp) \
: "r" (uaddr), "r" (oparg), "Ir" (-EFAULT) \
: "cc", "memory")
@@ -73,14 +73,14 @@
#include <linux/preempt.h>
#include <asm/domain.h>
-#define __futex_atomic_op(insn, ret, oldval, uaddr, oparg) \
+#define __futex_atomic_op(insn, ret, oldval, tmp, uaddr, oparg) \
__asm__ __volatile__( \
- "1: " T(ldr) " %1, [%2]\n" \
+ "1: " T(ldr) " %1, [%3]\n" \
" " insn "\n" \
- "2: " T(str) " %0, [%2]\n" \
+ "2: " T(str) " %0, [%3]\n" \
" mov %0, #0\n" \
- __futex_atomic_ex_table("%4") \
- : "=&r" (ret), "=&r" (oldval) \
+ __futex_atomic_ex_table("%5") \
+ : "=&r" (ret), "=&r" (oldval), "=&r" (tmp) \
: "r" (uaddr), "r" (oparg), "Ir" (-EFAULT) \
: "cc", "memory")
@@ -117,7 +117,7 @@
int cmp = (encoded_op >> 24) & 15;
int oparg = (encoded_op << 8) >> 20;
int cmparg = (encoded_op << 20) >> 20;
- int oldval = 0, ret;
+ int oldval = 0, ret, tmp;
if (encoded_op & (FUTEX_OP_OPARG_SHIFT << 28))
oparg = 1 << oparg;
@@ -129,19 +129,19 @@
switch (op) {
case FUTEX_OP_SET:
- __futex_atomic_op("mov %0, %3", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("mov %0, %4", ret, oldval, tmp, uaddr, oparg);
break;
case FUTEX_OP_ADD:
- __futex_atomic_op("add %0, %1, %3", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("add %0, %1, %4", ret, oldval, tmp, uaddr, oparg);
break;
case FUTEX_OP_OR:
- __futex_atomic_op("orr %0, %1, %3", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("orr %0, %1, %4", ret, oldval, tmp, uaddr, oparg);
break;
case FUTEX_OP_ANDN:
- __futex_atomic_op("and %0, %1, %3", ret, oldval, uaddr, ~oparg);
+ __futex_atomic_op("and %0, %1, %4", ret, oldval, tmp, uaddr, ~oparg);
break;
case FUTEX_OP_XOR:
- __futex_atomic_op("eor %0, %1, %3", ret, oldval, uaddr, oparg);
+ __futex_atomic_op("eor %0, %1, %4", ret, oldval, tmp, uaddr, oparg);
break;
default:
ret = -ENOSYS;
diff --git a/arch/arm/include/asm/hardware/cache-l2x0.h b/arch/arm/include/asm/hardware/cache-l2x0.h
index 16bd480..99a6ed7 100644
--- a/arch/arm/include/asm/hardware/cache-l2x0.h
+++ b/arch/arm/include/asm/hardware/cache-l2x0.h
@@ -45,8 +45,13 @@
#define L2X0_CLEAN_INV_LINE_PA 0x7F0
#define L2X0_CLEAN_INV_LINE_IDX 0x7F8
#define L2X0_CLEAN_INV_WAY 0x7FC
-#define L2X0_LOCKDOWN_WAY_D 0x900
-#define L2X0_LOCKDOWN_WAY_I 0x904
+/*
+ * The lockdown registers repeat 8 times for L310, the L210 has only one
+ * D and one I lockdown register at 0x0900 and 0x0904.
+ */
+#define L2X0_LOCKDOWN_WAY_D_BASE 0x900
+#define L2X0_LOCKDOWN_WAY_I_BASE 0x904
+#define L2X0_LOCKDOWN_STRIDE 0x08
#define L2X0_TEST_OPERATION 0xF00
#define L2X0_LINE_DATA 0xF10
#define L2X0_LINE_TAG 0xF30
@@ -64,7 +69,7 @@
#define L2X0_AUX_CTRL_MASK 0xc0000fff
#define L2X0_AUX_CTRL_ASSOCIATIVITY_SHIFT 16
#define L2X0_AUX_CTRL_WAY_SIZE_SHIFT 17
-#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x3 << 17)
+#define L2X0_AUX_CTRL_WAY_SIZE_MASK (0x7 << 17)
#define L2X0_AUX_CTRL_SHARE_OVERRIDE_SHIFT 22
#define L2X0_AUX_CTRL_NS_LOCKDOWN_SHIFT 26
#define L2X0_AUX_CTRL_NS_INT_CTRL_SHIFT 27
diff --git a/arch/arm/include/asm/pmu.h b/arch/arm/include/asm/pmu.h
index 67c70a3..b7e82c4 100644
--- a/arch/arm/include/asm/pmu.h
+++ b/arch/arm/include/asm/pmu.h
@@ -41,7 +41,7 @@
* encoded error on failure.
*/
extern struct platform_device *
-reserve_pmu(enum arm_pmu_type device);
+reserve_pmu(enum arm_pmu_type type);
/**
* release_pmu() - Relinquish control of the performance counters
@@ -62,26 +62,26 @@
* the actual hardware initialisation.
*/
extern int
-init_pmu(enum arm_pmu_type device);
+init_pmu(enum arm_pmu_type type);
#else /* CONFIG_CPU_HAS_PMU */
#include <linux/err.h>
static inline struct platform_device *
-reserve_pmu(enum arm_pmu_type device)
+reserve_pmu(enum arm_pmu_type type)
{
return ERR_PTR(-ENODEV);
}
static inline int
-release_pmu(struct platform_device *pdev)
+release_pmu(enum arm_pmu_type type)
{
return -ENODEV;
}
static inline int
-init_pmu(enum arm_pmu_type device)
+init_pmu(enum arm_pmu_type type)
{
return -ENODEV;
}
diff --git a/arch/arm/include/asm/unistd.h b/arch/arm/include/asm/unistd.h
index 2c04ed5..c60a294 100644
--- a/arch/arm/include/asm/unistd.h
+++ b/arch/arm/include/asm/unistd.h
@@ -478,8 +478,8 @@
/*
* Unimplemented (or alternatively implemented) syscalls
*/
-#define __IGNORE_fadvise64_64 1
-#define __IGNORE_migrate_pages 1
+#define __IGNORE_fadvise64_64
+#define __IGNORE_migrate_pages
#endif /* __KERNEL__ */
#endif /* __ASM_ARM_UNISTD_H */
diff --git a/arch/arm/kernel/calls.S b/arch/arm/kernel/calls.S
index 80f7896..9943e9e 100644
--- a/arch/arm/kernel/calls.S
+++ b/arch/arm/kernel/calls.S
@@ -178,7 +178,7 @@
CALL(sys_ni_syscall) /* vm86 */
CALL(sys_ni_syscall) /* was sys_query_module */
CALL(sys_poll)
- CALL(sys_nfsservctl)
+ CALL(sys_ni_syscall) /* was nfsservctl */
/* 170 */ CALL(sys_setresgid16)
CALL(sys_getresgid16)
CALL(sys_prctl)
diff --git a/arch/arm/kernel/pmu.c b/arch/arm/kernel/pmu.c
index 2b70709..c53474f 100644
--- a/arch/arm/kernel/pmu.c
+++ b/arch/arm/kernel/pmu.c
@@ -31,7 +31,7 @@
{
if (type < 0 || type >= ARM_NUM_PMU_DEVICES) {
pr_warning("received registration request for unknown "
- "device %d\n", type);
+ "PMU device type %d\n", type);
return -EINVAL;
}
@@ -112,17 +112,17 @@
device_initcall(register_pmu_driver);
struct platform_device *
-reserve_pmu(enum arm_pmu_type device)
+reserve_pmu(enum arm_pmu_type type)
{
struct platform_device *pdev;
- if (test_and_set_bit_lock(device, &pmu_lock)) {
+ if (test_and_set_bit_lock(type, &pmu_lock)) {
pdev = ERR_PTR(-EBUSY);
- } else if (pmu_devices[device] == NULL) {
- clear_bit_unlock(device, &pmu_lock);
+ } else if (pmu_devices[type] == NULL) {
+ clear_bit_unlock(type, &pmu_lock);
pdev = ERR_PTR(-ENODEV);
} else {
- pdev = pmu_devices[device];
+ pdev = pmu_devices[type];
}
return pdev;
@@ -130,11 +130,11 @@
EXPORT_SYMBOL_GPL(reserve_pmu);
int
-release_pmu(enum arm_pmu_type device)
+release_pmu(enum arm_pmu_type type)
{
- if (WARN_ON(!pmu_devices[device]))
+ if (WARN_ON(!pmu_devices[type]))
return -EINVAL;
- clear_bit_unlock(device, &pmu_lock);
+ clear_bit_unlock(type, &pmu_lock);
return 0;
}
EXPORT_SYMBOL_GPL(release_pmu);
@@ -182,17 +182,17 @@
}
int
-init_pmu(enum arm_pmu_type device)
+init_pmu(enum arm_pmu_type type)
{
int err = 0;
- switch (device) {
+ switch (type) {
case ARM_PMU_DEVICE_CPU:
err = init_cpu_pmu();
break;
default:
- pr_warning("attempt to initialise unknown device %d\n",
- device);
+ pr_warning("attempt to initialise PMU of unknown "
+ "type %d\n", type);
err = -EINVAL;
}
diff --git a/arch/arm/kernel/relocate_kernel.S b/arch/arm/kernel/relocate_kernel.S
index 9cf4cbf..d0cdedf 100644
--- a/arch/arm/kernel/relocate_kernel.S
+++ b/arch/arm/kernel/relocate_kernel.S
@@ -57,7 +57,8 @@
mov r0,#0
ldr r1,kexec_mach_type
ldr r2,kexec_boot_atags
- mov pc,lr
+ ARM( mov pc, lr )
+ THUMB( bx lr )
.align
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index 70bca64..e514c76 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -280,18 +280,19 @@
if (arch >= CPU_ARCH_ARMv6) {
if ((cachetype & (7 << 29)) == 4 << 29) {
/* ARMv7 register format */
+ arch = CPU_ARCH_ARMv7;
cacheid = CACHEID_VIPT_NONALIASING;
if ((cachetype & (3 << 14)) == 1 << 14)
cacheid |= CACHEID_ASID_TAGGED;
- else if (cpu_has_aliasing_icache(CPU_ARCH_ARMv7))
- cacheid |= CACHEID_VIPT_I_ALIASING;
- } else if (cachetype & (1 << 23)) {
- cacheid = CACHEID_VIPT_ALIASING;
} else {
- cacheid = CACHEID_VIPT_NONALIASING;
- if (cpu_has_aliasing_icache(CPU_ARCH_ARMv6))
- cacheid |= CACHEID_VIPT_I_ALIASING;
+ arch = CPU_ARCH_ARMv6;
+ if (cachetype & (1 << 23))
+ cacheid = CACHEID_VIPT_ALIASING;
+ else
+ cacheid = CACHEID_VIPT_NONALIASING;
}
+ if (cpu_has_aliasing_icache(arch))
+ cacheid |= CACHEID_VIPT_I_ALIASING;
} else {
cacheid = CACHEID_VIVT;
}
diff --git a/arch/arm/kernel/smp_scu.c b/arch/arm/kernel/smp_scu.c
index 79ed5e7..7fcddb7 100644
--- a/arch/arm/kernel/smp_scu.c
+++ b/arch/arm/kernel/smp_scu.c
@@ -13,6 +13,7 @@
#include <asm/smp_scu.h>
#include <asm/cacheflush.h>
+#include <asm/cputype.h>
#define SCU_CTRL 0x00
#define SCU_CONFIG 0x04
@@ -37,6 +38,15 @@
{
u32 scu_ctrl;
+#ifdef CONFIG_ARM_ERRATA_764369
+ /* Cortex-A9 only */
+ if ((read_cpuid(CPUID_ID) & 0xff0ffff0) == 0x410fc090) {
+ scu_ctrl = __raw_readl(scu_base + 0x30);
+ if (!(scu_ctrl & 1))
+ __raw_writel(scu_ctrl | 0x1, scu_base + 0x30);
+ }
+#endif
+
scu_ctrl = __raw_readl(scu_base + SCU_CTRL);
/* already enabled? */
if (scu_ctrl & 1)
diff --git a/arch/arm/kernel/smp_twd.c b/arch/arm/kernel/smp_twd.c
index 2c277d4..01c1862 100644
--- a/arch/arm/kernel/smp_twd.c
+++ b/arch/arm/kernel/smp_twd.c
@@ -137,8 +137,8 @@
clk->max_delta_ns = clockevent_delta2ns(0xffffffff, clk);
clk->min_delta_ns = clockevent_delta2ns(0xf, clk);
+ clockevents_register_device(clk);
+
/* Make sure our local interrupt controller has this enabled */
gic_enable_ppi(clk->irq);
-
- clockevents_register_device(clk);
}
diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S
index bf977f8..4e66f62 100644
--- a/arch/arm/kernel/vmlinux.lds.S
+++ b/arch/arm/kernel/vmlinux.lds.S
@@ -23,8 +23,10 @@
#if defined(CONFIG_SMP_ON_UP) && !defined(CONFIG_DEBUG_SPINLOCK)
#define ARM_EXIT_KEEP(x) x
+#define ARM_EXIT_DISCARD(x)
#else
#define ARM_EXIT_KEEP(x)
+#define ARM_EXIT_DISCARD(x) x
#endif
OUTPUT_ARCH(arm)
@@ -39,6 +41,11 @@
SECTIONS
{
/*
+ * XXX: The linker does not define how output sections are
+ * assigned to input sections when there are multiple statements
+ * matching the same input section name. There is no documented
+ * order of matching.
+ *
* unwind exit sections must be discarded before the rest of the
* unwind sections get included.
*/
@@ -47,6 +54,9 @@
*(.ARM.extab.exit.text)
ARM_CPU_DISCARD(*(.ARM.exidx.cpuexit.text))
ARM_CPU_DISCARD(*(.ARM.extab.cpuexit.text))
+ ARM_EXIT_DISCARD(EXIT_TEXT)
+ ARM_EXIT_DISCARD(EXIT_DATA)
+ EXIT_CALL
#ifndef CONFIG_HOTPLUG
*(.ARM.exidx.devexit.text)
*(.ARM.extab.devexit.text)
@@ -58,6 +68,8 @@
#ifndef CONFIG_SMP_ON_UP
*(.alt.smp.init)
#endif
+ *(.discard)
+ *(.discard.*)
}
#ifdef CONFIG_XIP_KERNEL
@@ -279,9 +291,6 @@
STABS_DEBUG
.comment 0 : { *(.comment) }
-
- /* Default discards */
- DISCARDS
}
/*
diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c
index d522b47..6c8e3b5 100644
--- a/arch/arm/mach-at91/at91sam9261.c
+++ b/arch/arm/mach-at91/at91sam9261.c
@@ -157,7 +157,7 @@
CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk),
CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk),
- CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc1_clk),
+ CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk),
diff --git a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
index 6bd83ed..d87bfc3 100644
--- a/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
+++ b/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
@@ -8,7 +8,6 @@
* published by the Free Software Foundation.
*/
-#include <mach/hardware.h>
#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
diff --git a/arch/arm/mach-cns3xxx/include/mach/system.h b/arch/arm/mach-cns3xxx/include/mach/system.h
index 58bb03a..4f16c9b 100644
--- a/arch/arm/mach-cns3xxx/include/mach/system.h
+++ b/arch/arm/mach-cns3xxx/include/mach/system.h
@@ -13,7 +13,6 @@
#include <linux/io.h>
#include <asm/proc-fns.h>
-#include <mach/hardware.h>
static inline void arch_idle(void)
{
diff --git a/arch/arm/mach-cns3xxx/include/mach/uncompress.h b/arch/arm/mach-cns3xxx/include/mach/uncompress.h
index de8ead9..a91b605 100644
--- a/arch/arm/mach-cns3xxx/include/mach/uncompress.h
+++ b/arch/arm/mach-cns3xxx/include/mach/uncompress.h
@@ -8,7 +8,6 @@
*/
#include <asm/mach-types.h>
-#include <mach/hardware.h>
#include <mach/cns3xxx.h>
#define AMBA_UART_DR(base) (*(volatile unsigned char *)((base) + 0x00))
diff --git a/arch/arm/mach-cns3xxx/pcie.c b/arch/arm/mach-cns3xxx/pcie.c
index 06fd25d..0f8fca4 100644
--- a/arch/arm/mach-cns3xxx/pcie.c
+++ b/arch/arm/mach-cns3xxx/pcie.c
@@ -49,7 +49,7 @@
return &cns3xxx_pcie[root->domain];
}
-static struct cns3xxx_pcie *pdev_to_cnspci(struct pci_dev *dev)
+static struct cns3xxx_pcie *pdev_to_cnspci(const struct pci_dev *dev)
{
return sysdata_to_cnspci(dev->sysdata);
}
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index bd53945..008d514 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -115,6 +115,32 @@
},
};
+#ifdef CONFIG_MTD
+static void da850_evm_m25p80_notify_add(struct mtd_info *mtd)
+{
+ char *mac_addr = davinci_soc_info.emac_pdata->mac_addr;
+ size_t retlen;
+
+ if (!strcmp(mtd->name, "MAC-Address")) {
+ mtd->read(mtd, 0, ETH_ALEN, &retlen, mac_addr);
+ if (retlen == ETH_ALEN)
+ pr_info("Read MAC addr from SPI Flash: %pM\n",
+ mac_addr);
+ }
+}
+
+static struct mtd_notifier da850evm_spi_notifier = {
+ .add = da850_evm_m25p80_notify_add,
+};
+
+static void da850_evm_setup_mac_addr(void)
+{
+ register_mtd_user(&da850evm_spi_notifier);
+}
+#else
+static void da850_evm_setup_mac_addr(void) { }
+#endif
+
static struct mtd_partition da850_evm_norflash_partition[] = {
{
.name = "bootloaders + env",
@@ -1244,6 +1270,8 @@
if (ret)
pr_warning("da850_evm_init: sata registration failed: %d\n",
ret);
+
+ da850_evm_setup_mac_addr();
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
diff --git a/arch/arm/mach-davinci/include/mach/psc.h b/arch/arm/mach-davinci/include/mach/psc.h
index 47fd0bc..fa59c09 100644
--- a/arch/arm/mach-davinci/include/mach/psc.h
+++ b/arch/arm/mach-davinci/include/mach/psc.h
@@ -243,7 +243,7 @@
#define PSC_STATE_DISABLE 2
#define PSC_STATE_ENABLE 3
-#define MDSTAT_STATE_MASK 0x1f
+#define MDSTAT_STATE_MASK 0x3f
#define MDCTL_FORCE BIT(31)
#ifndef __ASSEMBLER__
diff --git a/arch/arm/mach-davinci/sleep.S b/arch/arm/mach-davinci/sleep.S
index fb5e72b..5f1e045 100644
--- a/arch/arm/mach-davinci/sleep.S
+++ b/arch/arm/mach-davinci/sleep.S
@@ -217,7 +217,11 @@
ENDPROC(davinci_ddr_psc_config)
CACHE_FLUSH:
- .word arm926_flush_kern_cache_all
+#ifdef CONFIG_CPU_V6
+ .word v6_flush_kern_cache_all
+#else
+ .word arm926_flush_kern_cache_all
+#endif
ENTRY(davinci_cpu_suspend_sz)
.word . - davinci_cpu_suspend
diff --git a/arch/arm/mach-dove/common.c b/arch/arm/mach-dove/common.c
index 83dce85..a9e0dae 100644
--- a/arch/arm/mach-dove/common.c
+++ b/arch/arm/mach-dove/common.c
@@ -158,7 +158,7 @@
void __init dove_spi1_init(void)
{
- orion_spi_init(DOVE_SPI1_PHYS_BASE, get_tclk());
+ orion_spi_1_init(DOVE_SPI1_PHYS_BASE, get_tclk());
}
/*****************************************************************************
diff --git a/arch/arm/mach-ep93xx/include/mach/ts72xx.h b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
index 0eabec6..f1397a1 100644
--- a/arch/arm/mach-ep93xx/include/mach/ts72xx.h
+++ b/arch/arm/mach-ep93xx/include/mach/ts72xx.h
@@ -6,7 +6,7 @@
* TS72xx memory map:
*
* virt phys size
- * febff000 22000000 4K model number register
+ * febff000 22000000 4K model number register (bits 0-2)
* febfe000 22400000 4K options register
* febfd000 22800000 4K options register #2
* febf9000 10800000 4K TS-5620 RTC index register
@@ -20,6 +20,9 @@
#define TS72XX_MODEL_TS7200 0x00
#define TS72XX_MODEL_TS7250 0x01
#define TS72XX_MODEL_TS7260 0x02
+#define TS72XX_MODEL_TS7300 0x03
+#define TS72XX_MODEL_TS7400 0x04
+#define TS72XX_MODEL_MASK 0x07
#define TS72XX_OPTIONS_PHYS_BASE 0x22400000
@@ -51,19 +54,34 @@
#ifndef __ASSEMBLY__
+static inline int ts72xx_model(void)
+{
+ return __raw_readb(TS72XX_MODEL_VIRT_BASE) & TS72XX_MODEL_MASK;
+}
+
static inline int board_is_ts7200(void)
{
- return __raw_readb(TS72XX_MODEL_VIRT_BASE) == TS72XX_MODEL_TS7200;
+ return ts72xx_model() == TS72XX_MODEL_TS7200;
}
static inline int board_is_ts7250(void)
{
- return __raw_readb(TS72XX_MODEL_VIRT_BASE) == TS72XX_MODEL_TS7250;
+ return ts72xx_model() == TS72XX_MODEL_TS7250;
}
static inline int board_is_ts7260(void)
{
- return __raw_readb(TS72XX_MODEL_VIRT_BASE) == TS72XX_MODEL_TS7260;
+ return ts72xx_model() == TS72XX_MODEL_TS7260;
+}
+
+static inline int board_is_ts7300(void)
+{
+ return ts72xx_model() == TS72XX_MODEL_TS7300;
+}
+
+static inline int board_is_ts7400(void)
+{
+ return ts72xx_model() == TS72XX_MODEL_TS7400;
}
static inline int is_max197_installed(void)
diff --git a/arch/arm/mach-exynos4/clock.c b/arch/arm/mach-exynos4/clock.c
index 851dea0..86964d2 100644
--- a/arch/arm/mach-exynos4/clock.c
+++ b/arch/arm/mach-exynos4/clock.c
@@ -520,7 +520,7 @@
.ctrlbit = (1 << 21),
}, {
.name = "ac97",
- .id = -1,
+ .devname = "samsung-ac97",
.enable = exynos4_clk_ip_peril_ctrl,
.ctrlbit = (1 << 27),
}, {
@@ -899,8 +899,7 @@
.reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 28, .size = 4 },
}, {
.clk = {
- .name = "sclk_cam",
- .devname = "exynos4-fimc.0",
+ .name = "sclk_cam0",
.enable = exynos4_clksrc_mask_cam_ctrl,
.ctrlbit = (1 << 16),
},
@@ -909,8 +908,7 @@
.reg_div = { .reg = S5P_CLKDIV_CAM, .shift = 16, .size = 4 },
}, {
.clk = {
- .name = "sclk_cam",
- .devname = "exynos4-fimc.1",
+ .name = "sclk_cam1",
.enable = exynos4_clksrc_mask_cam_ctrl,
.ctrlbit = (1 << 20),
},
@@ -1160,7 +1158,7 @@
vpllsrc = clk_get_rate(&clk_vpllsrc.clk);
vpll = s5p_get_pll46xx(vpllsrc, __raw_readl(S5P_VPLL_CON0),
- __raw_readl(S5P_VPLL_CON1), pll_4650);
+ __raw_readl(S5P_VPLL_CON1), pll_4650c);
clk_fout_apll.ops = &exynos4_fout_apll_ops;
clk_fout_mpll.rate = mpll;
diff --git a/arch/arm/mach-exynos4/cpu.c b/arch/arm/mach-exynos4/cpu.c
index 2d8a40c..746d6fc 100644
--- a/arch/arm/mach-exynos4/cpu.c
+++ b/arch/arm/mach-exynos4/cpu.c
@@ -24,12 +24,13 @@
#include <plat/exynos4.h>
#include <plat/adc-core.h>
#include <plat/sdhci.h>
-#include <plat/devs.h>
#include <plat/fb-core.h>
#include <plat/fimc-core.h>
#include <plat/iic-core.h>
+#include <plat/reset.h>
#include <mach/regs-irq.h>
+#include <mach/regs-pmu.h>
extern int combiner_init(unsigned int combiner_nr, void __iomem *base,
unsigned int irq_start);
@@ -128,6 +129,11 @@
local_irq_enable();
}
+static void exynos4_sw_reset(void)
+{
+ __raw_writel(0x1, S5P_SWRESET);
+}
+
/*
* exynos4_map_io
*
@@ -241,5 +247,8 @@
/* set idle function */
pm_idle = exynos4_idle;
+ /* set sw_reset function */
+ s5p_reset_hook = exynos4_sw_reset;
+
return sysdev_register(&exynos4_sysdev);
}
diff --git a/arch/arm/mach-exynos4/include/mach/irqs.h b/arch/arm/mach-exynos4/include/mach/irqs.h
index 934d2a4..f8952f8 100644
--- a/arch/arm/mach-exynos4/include/mach/irqs.h
+++ b/arch/arm/mach-exynos4/include/mach/irqs.h
@@ -80,9 +80,8 @@
#define IRQ_HSMMC3 IRQ_SPI(76)
#define IRQ_DWMCI IRQ_SPI(77)
-#define IRQ_MIPICSI0 IRQ_SPI(78)
-
-#define IRQ_MIPICSI1 IRQ_SPI(80)
+#define IRQ_MIPI_CSIS0 IRQ_SPI(78)
+#define IRQ_MIPI_CSIS1 IRQ_SPI(80)
#define IRQ_ONENAND_AUDI IRQ_SPI(82)
#define IRQ_ROTATOR IRQ_SPI(83)
diff --git a/arch/arm/mach-exynos4/include/mach/regs-pmu.h b/arch/arm/mach-exynos4/include/mach/regs-pmu.h
index fa49bbb..cdf9b47 100644
--- a/arch/arm/mach-exynos4/include/mach/regs-pmu.h
+++ b/arch/arm/mach-exynos4/include/mach/regs-pmu.h
@@ -29,6 +29,8 @@
#define S5P_USE_STANDBY_WFE1 (1 << 25)
#define S5P_USE_MASK ((0x3 << 16) | (0x3 << 24))
+#define S5P_SWRESET S5P_PMUREG(0x0400)
+
#define S5P_WAKEUP_STAT S5P_PMUREG(0x0600)
#define S5P_EINT_WAKEUP_MASK S5P_PMUREG(0x0604)
#define S5P_WAKEUP_MASK S5P_PMUREG(0x0608)
diff --git a/arch/arm/mach-exynos4/irq-eint.c b/arch/arm/mach-exynos4/irq-eint.c
index 9d87d2a..badb8c6 100644
--- a/arch/arm/mach-exynos4/irq-eint.c
+++ b/arch/arm/mach-exynos4/irq-eint.c
@@ -23,6 +23,8 @@
#include <mach/regs-gpio.h>
+#include <asm/mach/irq.h>
+
static DEFINE_SPINLOCK(eint_lock);
static unsigned int eint0_15_data[16];
@@ -184,8 +186,11 @@
static void exynos4_irq_demux_eint16_31(unsigned int irq, struct irq_desc *desc)
{
+ struct irq_chip *chip = irq_get_chip(irq);
+ chained_irq_enter(chip, desc);
exynos4_irq_demux_eint(IRQ_EINT(16));
exynos4_irq_demux_eint(IRQ_EINT(24));
+ chained_irq_exit(chip, desc);
}
static void exynos4_irq_eint0_15(unsigned int irq, struct irq_desc *desc)
@@ -193,6 +198,7 @@
u32 *irq_data = irq_get_handler_data(irq);
struct irq_chip *chip = irq_get_chip(irq);
+ chained_irq_enter(chip, desc);
chip->irq_mask(&desc->irq_data);
if (chip->irq_ack)
@@ -201,6 +207,7 @@
generic_handle_irq(*irq_data);
chip->irq_unmask(&desc->irq_data);
+ chained_irq_exit(chip, desc);
}
int __init exynos4_init_irq_eint(void)
diff --git a/arch/arm/mach-exynos4/mach-universal_c210.c b/arch/arm/mach-exynos4/mach-universal_c210.c
index 0e280d1..b3b5d89 100644
--- a/arch/arm/mach-exynos4/mach-universal_c210.c
+++ b/arch/arm/mach-exynos4/mach-universal_c210.c
@@ -79,7 +79,7 @@
};
static struct regulator_consumer_supply max8952_consumer =
- REGULATOR_SUPPLY("vddarm", NULL);
+ REGULATOR_SUPPLY("vdd_arm", NULL);
static struct max8952_platform_data universal_max8952_pdata __initdata = {
.gpio_vid0 = EXYNOS4_GPX0(3),
@@ -105,7 +105,7 @@
};
static struct regulator_consumer_supply lp3974_buck1_consumer =
- REGULATOR_SUPPLY("vddint", NULL);
+ REGULATOR_SUPPLY("vdd_int", NULL);
static struct regulator_consumer_supply lp3974_buck2_consumer =
REGULATOR_SUPPLY("vddg3d", NULL);
diff --git a/arch/arm/mach-exynos4/mct.c b/arch/arm/mach-exynos4/mct.c
index 1ae059b..ddd8686 100644
--- a/arch/arm/mach-exynos4/mct.c
+++ b/arch/arm/mach-exynos4/mct.c
@@ -132,12 +132,18 @@
return ((cycle_t)hi << 32) | lo;
}
+static void exynos4_frc_resume(struct clocksource *cs)
+{
+ exynos4_mct_frc_start(0, 0);
+}
+
struct clocksource mct_frc = {
.name = "mct-frc",
.rating = 400,
.read = exynos4_frc_read,
.mask = CLOCKSOURCE_MASK(64),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
+ .resume = exynos4_frc_resume,
};
static void __init exynos4_clocksource_init(void)
@@ -389,9 +395,11 @@
}
/* Setup the local clock events for a CPU */
-void __cpuinit local_timer_setup(struct clock_event_device *evt)
+int __cpuinit local_timer_setup(struct clock_event_device *evt)
{
exynos4_mct_tick_init(evt);
+
+ return 0;
}
int local_timer_ack(void)
diff --git a/arch/arm/mach-exynos4/platsmp.c b/arch/arm/mach-exynos4/platsmp.c
index 7c2282c..df6ef1b 100644
--- a/arch/arm/mach-exynos4/platsmp.c
+++ b/arch/arm/mach-exynos4/platsmp.c
@@ -106,6 +106,8 @@
*/
spin_lock(&boot_lock);
spin_unlock(&boot_lock);
+
+ set_cpu_online(cpu, true);
}
int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
diff --git a/arch/arm/mach-exynos4/setup-keypad.c b/arch/arm/mach-exynos4/setup-keypad.c
index 1ee0ebf..7862bfb 100644
--- a/arch/arm/mach-exynos4/setup-keypad.c
+++ b/arch/arm/mach-exynos4/setup-keypad.c
@@ -19,15 +19,16 @@
if (rows > 8) {
/* Set all the necessary GPX2 pins: KP_ROW[0~7] */
- s3c_gpio_cfgrange_nopull(EXYNOS4_GPX2(0), 8, S3C_GPIO_SFN(3));
+ s3c_gpio_cfgall_range(EXYNOS4_GPX2(0), 8, S3C_GPIO_SFN(3),
+ S3C_GPIO_PULL_UP);
/* Set all the necessary GPX3 pins: KP_ROW[8~] */
- s3c_gpio_cfgrange_nopull(EXYNOS4_GPX3(0), (rows - 8),
- S3C_GPIO_SFN(3));
+ s3c_gpio_cfgall_range(EXYNOS4_GPX3(0), (rows - 8),
+ S3C_GPIO_SFN(3), S3C_GPIO_PULL_UP);
} else {
/* Set all the necessary GPX2 pins: KP_ROW[x] */
- s3c_gpio_cfgrange_nopull(EXYNOS4_GPX2(0), rows,
- S3C_GPIO_SFN(3));
+ s3c_gpio_cfgall_range(EXYNOS4_GPX2(0), rows, S3C_GPIO_SFN(3),
+ S3C_GPIO_PULL_UP);
}
/* Set all the necessary GPX1 pins to special-function 3: KP_COL[x] */
diff --git a/arch/arm/mach-exynos4/setup-usb-phy.c b/arch/arm/mach-exynos4/setup-usb-phy.c
index 0883c1b..39aca04 100644
--- a/arch/arm/mach-exynos4/setup-usb-phy.c
+++ b/arch/arm/mach-exynos4/setup-usb-phy.c
@@ -82,7 +82,7 @@
rstcon &= ~(HOST_LINK_PORT_SWRST_MASK | PHY1_SWRST_MASK);
writel(rstcon, EXYNOS4_RSTCON);
- udelay(50);
+ udelay(80);
clk_disable(otg_clk);
clk_put(otg_clk);
diff --git a/arch/arm/mach-footbridge/Kconfig b/arch/arm/mach-footbridge/Kconfig
index dc26fff..c8e7afc 100644
--- a/arch/arm/mach-footbridge/Kconfig
+++ b/arch/arm/mach-footbridge/Kconfig
@@ -62,6 +62,7 @@
config ARCH_NETWINDER
bool "NetWinder"
select CLKSRC_I8253
+ select CLKEVT_I8253
select FOOTBRIDGE_HOST
select ISA
select ISA_DMA
diff --git a/arch/arm/mach-footbridge/dc21285.c b/arch/arm/mach-footbridge/dc21285.c
index 1331fff..18c32a5 100644
--- a/arch/arm/mach-footbridge/dc21285.c
+++ b/arch/arm/mach-footbridge/dc21285.c
@@ -18,6 +18,7 @@
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/spinlock.h>
+#include <video/vga.h>
#include <asm/irq.h>
#include <asm/system.h>
diff --git a/arch/arm/mach-imx/mach-cpuimx27.c b/arch/arm/mach-imx/mach-cpuimx27.c
index b0cd62d..a8364cc 100644
--- a/arch/arm/mach-imx/mach-cpuimx27.c
+++ b/arch/arm/mach-imx/mach-cpuimx27.c
@@ -310,7 +310,7 @@
.init = eukrea_cpuimx27_timer_init,
};
-MACHINE_START(CPUIMX27, "EUKREA CPUIMX27")
+MACHINE_START(EUKREA_CPUIMX27, "EUKREA CPUIMX27")
.boot_params = MX27_PHYS_OFFSET + 0x100,
.map_io = mx27_map_io,
.init_early = imx27_init_early,
diff --git a/arch/arm/mach-imx/mach-cpuimx35.c b/arch/arm/mach-imx/mach-cpuimx35.c
index bd4dbea..fc4fea1 100644
--- a/arch/arm/mach-imx/mach-cpuimx35.c
+++ b/arch/arm/mach-imx/mach-cpuimx35.c
@@ -192,7 +192,7 @@
.init = eukrea_cpuimx35_timer_init,
};
-MACHINE_START(EUKREA_CPUIMX35, "Eukrea CPUIMX35")
+MACHINE_START(EUKREA_CPUIMX35SD, "Eukrea CPUIMX35")
/* Maintainer: Eukrea Electromatique */
.boot_params = MX3x_PHYS_OFFSET + 0x100,
.map_io = mx35_map_io,
diff --git a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
index e2343c8..b05de09 100644
--- a/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
+++ b/arch/arm/mach-imx/mach-eukrea_cpuimx25.c
@@ -161,7 +161,7 @@
.init = eukrea_cpuimx25_timer_init,
};
-MACHINE_START(EUKREA_CPUIMX25, "Eukrea CPUIMX25")
+MACHINE_START(EUKREA_CPUIMX25SD, "Eukrea CPUIMX25")
/* Maintainer: Eukrea Electromatique */
.boot_params = MX25_PHYS_OFFSET + 0x100,
.map_io = mx25_map_io,
diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-integrator/integrator_ap.c
index 2fbbdd5..8cdc730 100644
--- a/arch/arm/mach-integrator/integrator_ap.c
+++ b/arch/arm/mach-integrator/integrator_ap.c
@@ -32,6 +32,7 @@
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/mtd/physmap.h>
+#include <video/vga.h>
#include <mach/hardware.h>
#include <mach/platform.h>
@@ -154,6 +155,7 @@
static void __init ap_map_io(void)
{
iotable_init(ap_io_desc, ARRAY_SIZE(ap_io_desc));
+ vga_base = PCI_MEMORY_VADDR;
}
#define INTEGRATOR_SC_VALID_INT 0x003fffff
@@ -337,15 +339,15 @@
static void integrator_clocksource_init(u32 khz)
{
void __iomem *base = (void __iomem *)TIMER2_VA_BASE;
- u32 ctrl = TIMER_CTRL_ENABLE;
+ u32 ctrl = TIMER_CTRL_ENABLE | TIMER_CTRL_PERIODIC;
if (khz >= 1500) {
khz /= 16;
- ctrl = TIMER_CTRL_DIV16;
+ ctrl |= TIMER_CTRL_DIV16;
}
- writel(ctrl, base + TIMER_CTRL);
writel(0xffff, base + TIMER_LOAD);
+ writel(ctrl, base + TIMER_CTRL);
clocksource_mmio_init(base + TIMER_VALUE, "timer2",
khz * 1000, 200, 16, clocksource_mmio_readl_down);
diff --git a/arch/arm/mach-integrator/pci_v3.c b/arch/arm/mach-integrator/pci_v3.c
index dd56bfb..11b86e5 100644
--- a/arch/arm/mach-integrator/pci_v3.c
+++ b/arch/arm/mach-integrator/pci_v3.c
@@ -27,7 +27,6 @@
#include <linux/spinlock.h>
#include <linux/init.h>
#include <linux/io.h>
-#include <video/vga.h>
#include <mach/hardware.h>
#include <mach/platform.h>
@@ -505,7 +504,6 @@
pcibios_min_io = 0x6000;
pcibios_min_mem = 0x00100000;
- vga_base = PCI_MEMORY_VADDR;
/*
* Hook in our fault handler for PCI errors
diff --git a/arch/arm/mach-mx5/board-mx53_ard.c b/arch/arm/mach-mx5/board-mx53_ard.c
index cb4d753..614edcb 100644
--- a/arch/arm/mach-mx5/board-mx53_ard.c
+++ b/arch/arm/mach-mx5/board-mx53_ard.c
@@ -234,6 +234,7 @@
imx53_add_imx_i2c(1, &mx53_ard_i2c2_data);
imx53_add_imx_i2c(2, &mx53_ard_i2c3_data);
imx_add_gpio_keys(&ard_button_data);
+ imx53_add_ahci_imx();
}
static void __init mx53_ard_timer_init(void)
diff --git a/arch/arm/mach-mx5/board-mx53_loco.c b/arch/arm/mach-mx5/board-mx53_loco.c
index 7149416..0af2766 100644
--- a/arch/arm/mach-mx5/board-mx53_loco.c
+++ b/arch/arm/mach-mx5/board-mx53_loco.c
@@ -293,6 +293,7 @@
imx53_add_sdhci_esdhc_imx(2, &mx53_loco_sd3_data);
imx_add_gpio_keys(&loco_button_data);
gpio_led_register_device(-1, &mx53loco_leds_data);
+ imx53_add_ahci_imx();
}
static void __init mx53_loco_timer_init(void)
diff --git a/arch/arm/mach-mx5/board-mx53_smd.c b/arch/arm/mach-mx5/board-mx53_smd.c
index e64fd2c..d12fd30 100644
--- a/arch/arm/mach-mx5/board-mx53_smd.c
+++ b/arch/arm/mach-mx5/board-mx53_smd.c
@@ -35,6 +35,7 @@
#include "devices-imx53.h"
#define SMD_FEC_PHY_RST IMX_GPIO_NR(7, 6)
+#define MX53_SMD_SATA_PWR_EN IMX_GPIO_NR(3, 3)
static iomux_v3_cfg_t mx53_smd_pads[] = {
MX53_PAD_CSI0_DAT10__UART1_TXD_MUX,
@@ -111,6 +112,19 @@
.bitrate = 100000,
};
+static inline void mx53_smd_ahci_pwr_on(void)
+{
+ int ret;
+
+ /* Enable SATA PWR */
+ ret = gpio_request_one(MX53_SMD_SATA_PWR_EN,
+ GPIOF_DIR_OUT | GPIOF_INIT_HIGH, "ahci-sata-pwr");
+ if (ret) {
+ pr_err("failed to enable SATA_PWR_EN: %d\n", ret);
+ return;
+ }
+}
+
static void __init mx53_smd_board_init(void)
{
imx53_soc_init();
@@ -125,6 +139,8 @@
imx53_add_sdhci_esdhc_imx(0, NULL);
imx53_add_sdhci_esdhc_imx(1, NULL);
imx53_add_sdhci_esdhc_imx(2, NULL);
+ mx53_smd_ahci_pwr_on();
+ imx53_add_ahci_imx();
}
static void __init mx53_smd_timer_init(void)
diff --git a/arch/arm/mach-mx5/clock-mx51-mx53.c b/arch/arm/mach-mx5/clock-mx51-mx53.c
index 2b9bd1f..b94879e 100644
--- a/arch/arm/mach-mx5/clock-mx51-mx53.c
+++ b/arch/arm/mach-mx5/clock-mx51-mx53.c
@@ -1401,6 +1401,22 @@
.secondary = &esdhc4_ipg_clk,
};
+static struct clk sata_clk = {
+ .parent = &ipg_clk,
+ .enable = _clk_max_enable,
+ .enable_reg = MXC_CCM_CCGR4,
+ .enable_shift = MXC_CCM_CCGRx_CG1_OFFSET,
+ .disable = _clk_max_disable,
+};
+
+static struct clk ahci_phy_clk = {
+ .parent = &usb_phy1_clk,
+};
+
+static struct clk ahci_dma_clk = {
+ .parent = &ahb_clk,
+};
+
DEFINE_CLOCK(mipi_esc_clk, 0, MXC_CCM_CCGR4, MXC_CCM_CCGRx_CG5_OFFSET, NULL, NULL, NULL, &pll2_sw_clk);
DEFINE_CLOCK(mipi_hsc2_clk, 0, MXC_CCM_CCGR4, MXC_CCM_CCGRx_CG4_OFFSET, NULL, NULL, &mipi_esc_clk, &pll2_sw_clk);
DEFINE_CLOCK(mipi_hsc1_clk, 0, MXC_CCM_CCGR4, MXC_CCM_CCGRx_CG3_OFFSET, NULL, NULL, &mipi_hsc2_clk, &pll2_sw_clk);
@@ -1513,6 +1529,9 @@
_REGISTER_CLOCK("imx-ssi.2", NULL, ssi3_clk)
_REGISTER_CLOCK("imx-keypad", NULL, dummy_clk)
_REGISTER_CLOCK("pata_imx", NULL, pata_clk)
+ _REGISTER_CLOCK("imx53-ahci.0", "ahci", sata_clk)
+ _REGISTER_CLOCK("imx53-ahci.0", "ahci_phy", ahci_phy_clk)
+ _REGISTER_CLOCK("imx53-ahci.0", "ahci_dma", ahci_dma_clk)
};
static void clk_tree_init(void)
diff --git a/arch/arm/mach-mx5/devices-imx53.h b/arch/arm/mach-mx5/devices-imx53.h
index 7ca5d0c..6e1e5d1 100644
--- a/arch/arm/mach-mx5/devices-imx53.h
+++ b/arch/arm/mach-mx5/devices-imx53.h
@@ -44,3 +44,5 @@
extern const struct imx_pata_imx_data imx53_pata_imx_data;
#define imx53_add_pata_imx() \
imx_add_pata_imx(&imx53_pata_imx_data)
+
+extern struct platform_device *__init imx53_add_ahci_imx(void);
diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig
index fdf104f..cf00b3e 100644
--- a/arch/arm/mach-mxs/Kconfig
+++ b/arch/arm/mach-mxs/Kconfig
@@ -70,8 +70,25 @@
select MXS_HAVE_PLATFORM_MXS_PWM
select MXS_HAVE_PLATFORM_RTC_STMP3XXX
+config MODULE_M28
+ bool
+ select SOC_IMX28
+ select LEDS_GPIO_REGISTER
+ select MXS_HAVE_AMBA_DUART
+ select MXS_HAVE_PLATFORM_AUART
+ select MXS_HAVE_PLATFORM_FEC
+ select MXS_HAVE_PLATFORM_FLEXCAN
+ select MXS_HAVE_PLATFORM_MXS_I2C
+ select MXS_HAVE_PLATFORM_MXS_MMC
+ select MXS_HAVE_PLATFORM_MXSFB
+ select MXS_OCOTP
+
config MACH_TX28
bool "Ka-Ro TX28 module"
select MODULE_TX28
+config MACH_M28EVK
+ bool "Support DENX M28EVK Platform"
+ select MODULE_M28
+
endif
diff --git a/arch/arm/mach-mxs/Makefile b/arch/arm/mach-mxs/Makefile
index ea8dcb7..8c93b24 100644
--- a/arch/arm/mach-mxs/Makefile
+++ b/arch/arm/mach-mxs/Makefile
@@ -10,6 +10,7 @@
obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o
+obj-$(CONFIG_MACH_M28EVK) += mach-m28evk.o
obj-$(CONFIG_MODULE_TX28) += module-tx28.o
obj-$(CONFIG_MACH_TX28) += mach-tx28.o
diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c
index 7954013..e2fb70c 100644
--- a/arch/arm/mach-mxs/clock-mx28.c
+++ b/arch/arm/mach-mxs/clock-mx28.c
@@ -740,11 +740,17 @@
__raw_writel(BM_CLKCTRL_CPU_INTERRUPT_WAIT,
CLKCTRL_BASE_ADDR + HW_CLKCTRL_CPU_SET);
- /* Extra fec clock setting */
- reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
- reg &= ~BM_CLKCTRL_ENET_SLEEP;
- reg |= BM_CLKCTRL_ENET_CLK_OUT_EN;
- __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
+ /*
+ * Extra fec clock setting
+ * The DENX M28 uses an external clock source
+ * and the clock output must not be enabled
+ */
+ if (!machine_is_m28evk()) {
+ reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
+ reg &= ~BM_CLKCTRL_ENET_SLEEP;
+ reg |= BM_CLKCTRL_ENET_CLK_OUT_EN;
+ __raw_writel(reg, CLKCTRL_BASE_ADDR + HW_CLKCTRL_ENET);
+ }
/*
* 480 MHz seems too high to be ssp clock source directly,
diff --git a/arch/arm/mach-mxs/include/mach/mxs.h b/arch/arm/mach-mxs/include/mach/mxs.h
index 5aa5f75..0d2d2b4 100644
--- a/arch/arm/mach-mxs/include/mach/mxs.h
+++ b/arch/arm/mach-mxs/include/mach/mxs.h
@@ -33,6 +33,7 @@
0)
#define cpu_is_mx28() ( \
machine_is_mx28evk() || \
+ machine_is_m28evk() || \
machine_is_tx28() || \
0)
diff --git a/arch/arm/mach-mxs/include/mach/uncompress.h b/arch/arm/mach-mxs/include/mach/uncompress.h
index 7f8bf65..6777674 100644
--- a/arch/arm/mach-mxs/include/mach/uncompress.h
+++ b/arch/arm/mach-mxs/include/mach/uncompress.h
@@ -63,6 +63,7 @@
mxs_duart_base = MX23_DUART_BASE_ADDR;
break;
case MACH_TYPE_MX28EVK:
+ case MACH_TYPE_M28EVK:
case MACH_TYPE_TX28:
mxs_duart_base = MX28_DUART_BASE_ADDR;
break;
diff --git a/arch/arm/mach-mxs/mach-m28evk.c b/arch/arm/mach-mxs/mach-m28evk.c
new file mode 100644
index 0000000..3b1681e
--- /dev/null
+++ b/arch/arm/mach-mxs/mach-m28evk.c
@@ -0,0 +1,366 @@
+/*
+ * Copyright (C) 2011
+ * Stefano Babic, DENX Software Engineering, <sbabic@denx.de>
+ *
+ * based on: mach-mx28_evk.c
+ * Copyright 2010 Freescale Semiconductor, Inc. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/irq.h>
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include <mach/common.h>
+#include <mach/iomux-mx28.h>
+
+#include "devices-mx28.h"
+
+#define M28EVK_GPIO_USERLED1 MXS_GPIO_NR(3, 16)
+#define M28EVK_GPIO_USERLED2 MXS_GPIO_NR(3, 17)
+
+#define MX28EVK_BL_ENABLE MXS_GPIO_NR(3, 18)
+#define M28EVK_LCD_ENABLE MXS_GPIO_NR(3, 28)
+
+#define MX28EVK_MMC0_WRITE_PROTECT MXS_GPIO_NR(2, 12)
+#define MX28EVK_MMC1_WRITE_PROTECT MXS_GPIO_NR(0, 28)
+
+static const iomux_cfg_t m28evk_pads[] __initconst = {
+ /* duart */
+ MX28_PAD_AUART0_CTS__DUART_RX | MXS_PAD_CTRL,
+ MX28_PAD_AUART0_RTS__DUART_TX | MXS_PAD_CTRL,
+
+ /* auart0 */
+ MX28_PAD_AUART0_RX__AUART0_RX | MXS_PAD_CTRL,
+ MX28_PAD_AUART0_TX__AUART0_TX | MXS_PAD_CTRL,
+
+ /* auart3 */
+ MX28_PAD_AUART3_RX__AUART3_RX | MXS_PAD_CTRL,
+ MX28_PAD_AUART3_TX__AUART3_TX | MXS_PAD_CTRL,
+ MX28_PAD_AUART3_CTS__AUART3_CTS | MXS_PAD_CTRL,
+ MX28_PAD_AUART3_RTS__AUART3_RTS | MXS_PAD_CTRL,
+
+#define MXS_PAD_FEC (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP)
+ /* fec0 */
+ MX28_PAD_ENET0_MDC__ENET0_MDC | MXS_PAD_FEC,
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MXS_PAD_FEC,
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET | MXS_PAD_FEC,
+ /* fec1 */
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RXD2__ENET1_RXD0 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_COL__ENET1_TX_EN | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MXS_PAD_FEC,
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MXS_PAD_FEC,
+
+ /* flexcan0 */
+ MX28_PAD_GPMI_RDY2__CAN0_TX,
+ MX28_PAD_GPMI_RDY3__CAN0_RX,
+
+ /* flexcan1 */
+ MX28_PAD_GPMI_CE2N__CAN1_TX,
+ MX28_PAD_GPMI_CE3N__CAN1_RX,
+
+ /* I2C */
+ MX28_PAD_I2C0_SCL__I2C0_SCL,
+ MX28_PAD_I2C0_SDA__I2C0_SDA,
+
+ /* mxsfb (lcdif) */
+ MX28_PAD_LCD_D00__LCD_D0 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D01__LCD_D1 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D02__LCD_D2 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D03__LCD_D3 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D04__LCD_D4 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D05__LCD_D5 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D06__LCD_D6 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D07__LCD_D7 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D08__LCD_D8 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D09__LCD_D9 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D10__LCD_D10 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D11__LCD_D11 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D12__LCD_D12 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D13__LCD_D13 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D14__LCD_D14 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D15__LCD_D15 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D16__LCD_D16 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D17__LCD_D17 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D18__LCD_D18 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D19__LCD_D19 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D20__LCD_D20 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D21__LCD_D21 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D22__LCD_D22 | MXS_PAD_CTRL,
+ MX28_PAD_LCD_D23__LCD_D23 | MXS_PAD_CTRL,
+
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE | MXS_PAD_CTRL,
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK | MXS_PAD_CTRL,
+
+ /* mmc0 */
+ MX28_PAD_SSP0_DATA0__SSP0_D0 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA1__SSP0_D1 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA2__SSP0_D2 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA3__SSP0_D3 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA4__SSP0_D4 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA5__SSP0_D5 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA6__SSP0_D6 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DATA7__SSP0_D7 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_CMD__SSP0_CMD |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ MX28_PAD_SSP0_SCK__SSP0_SCK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+
+ /* mmc1 */
+ MX28_PAD_GPMI_D00__SSP1_D0 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D01__SSP1_D1 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D02__SSP1_D2 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D03__SSP1_D3 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D04__SSP1_D4 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D05__SSP1_D5 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D06__SSP1_D6 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_D07__SSP1_D7 |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_RDY1__SSP1_CMD |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_RDY0__SSP1_CARD_DETECT |
+ (MXS_PAD_8MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_WRN__SSP1_SCK |
+ (MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ /* write protect */
+ MX28_PAD_GPMI_RESETN__GPIO_0_28 |
+ (MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+ /* slot power enable */
+ MX28_PAD_PWM4__GPIO_3_29 |
+ (MXS_PAD_4MA | MXS_PAD_3V3 | MXS_PAD_NOPULL),
+
+ /* led */
+ MX28_PAD_PWM0__GPIO_3_16 | MXS_PAD_CTRL,
+ MX28_PAD_PWM1__GPIO_3_17 | MXS_PAD_CTRL,
+
+ /* nand */
+ MX28_PAD_GPMI_D00__GPMI_D0 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D01__GPMI_D1 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D02__GPMI_D2 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D03__GPMI_D3 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D04__GPMI_D4 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D05__GPMI_D5 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D06__GPMI_D6 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_D07__GPMI_D7 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_CE0N__GPMI_CE0N |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_RDY0__GPMI_READY0 |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_NOPULL),
+ MX28_PAD_GPMI_RDN__GPMI_RDN |
+ (MXS_PAD_12MA | MXS_PAD_1V8 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_WRN__GPMI_WRN |
+ (MXS_PAD_12MA | MXS_PAD_1V8 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_ALE__GPMI_ALE |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_CLE__GPMI_CLE |
+ (MXS_PAD_4MA | MXS_PAD_1V8 | MXS_PAD_PULLUP),
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN |
+ (MXS_PAD_12MA | MXS_PAD_1V8 | MXS_PAD_PULLUP),
+
+ /* Backlight */
+ MX28_PAD_PWM3__GPIO_3_28 | MXS_PAD_CTRL,
+};
+
+/* led */
+static const struct gpio_led m28evk_leds[] __initconst = {
+ {
+ .name = "user-led1",
+ .default_trigger = "heartbeat",
+ .gpio = M28EVK_GPIO_USERLED1,
+ },
+ {
+ .name = "user-led2",
+ .default_trigger = "heartbeat",
+ .gpio = M28EVK_GPIO_USERLED2,
+ },
+};
+
+static const struct gpio_led_platform_data m28evk_led_data __initconst = {
+ .leds = m28evk_leds,
+ .num_leds = ARRAY_SIZE(m28evk_leds),
+};
+
+static struct fec_platform_data mx28_fec_pdata[] __initdata = {
+ {
+ /* fec0 */
+ .phy = PHY_INTERFACE_MODE_RMII,
+ }, {
+ /* fec1 */
+ .phy = PHY_INTERFACE_MODE_RMII,
+ },
+};
+
+static int __init m28evk_fec_get_mac(void)
+{
+ int i;
+ u32 val;
+ const u32 *ocotp = mxs_get_ocotp();
+
+ if (!ocotp) {
+ pr_err("%s: timeout when reading fec mac from OCOTP\n",
+ __func__);
+ return -ETIMEDOUT;
+ }
+
+ /*
+ * OCOTP only stores the last 4 octets for each mac address,
+ * so hard-code DENX OUI (C0:E5:4E) here.
+ */
+ for (i = 0; i < 2; i++) {
+ val = ocotp[i * 4];
+ mx28_fec_pdata[i].mac[0] = 0xC0;
+ mx28_fec_pdata[i].mac[1] = 0xE5;
+ mx28_fec_pdata[i].mac[2] = 0x4E;
+ mx28_fec_pdata[i].mac[3] = (val >> 16) & 0xff;
+ mx28_fec_pdata[i].mac[4] = (val >> 8) & 0xff;
+ mx28_fec_pdata[i].mac[5] = (val >> 0) & 0xff;
+ }
+
+ return 0;
+}
+
+/* mxsfb (lcdif) */
+static struct fb_videomode m28evk_video_modes[] = {
+ {
+ .name = "Ampire AM-800480R2TMQW-T01H",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 30066, /* picosecond (33.26 MHz) */
+ .left_margin = 0,
+ .right_margin = 256,
+ .upper_margin = 0,
+ .lower_margin = 45,
+ .hsync_len = 1,
+ .vsync_len = 1,
+ .sync = FB_SYNC_DATA_ENABLE_HIGH_ACT,
+ },
+};
+
+static const struct mxsfb_platform_data m28evk_mxsfb_pdata __initconst = {
+ .mode_list = m28evk_video_modes,
+ .mode_count = ARRAY_SIZE(m28evk_video_modes),
+ .default_bpp = 16,
+ .ld_intf_width = STMLCDIF_18BIT,
+};
+
+static struct at24_platform_data m28evk_eeprom = {
+ .byte_len = 16384,
+ .page_size = 32,
+ .flags = AT24_FLAG_ADDR16,
+};
+
+static struct i2c_board_info m28_stk5v3_i2c_boardinfo[] __initdata = {
+ {
+ I2C_BOARD_INFO("at24", 0x51), /* E0=1, E1=0, E2=0 */
+ .platform_data = &m28evk_eeprom,
+ },
+};
+
+static struct mxs_mmc_platform_data m28evk_mmc_pdata[] __initdata = {
+ {
+ /* mmc0 */
+ .wp_gpio = MX28EVK_MMC0_WRITE_PROTECT,
+ .flags = SLOTF_8_BIT_CAPABLE,
+ }, {
+ /* mmc1 */
+ .wp_gpio = MX28EVK_MMC1_WRITE_PROTECT,
+ .flags = SLOTF_8_BIT_CAPABLE,
+ },
+};
+
+static void __init m28evk_init(void)
+{
+ mxs_iomux_setup_multiple_pads(m28evk_pads, ARRAY_SIZE(m28evk_pads));
+
+ mx28_add_duart();
+ mx28_add_auart0();
+ mx28_add_auart3();
+
+ if (!m28evk_fec_get_mac()) {
+ mx28_add_fec(0, &mx28_fec_pdata[0]);
+ mx28_add_fec(1, &mx28_fec_pdata[1]);
+ }
+
+ mx28_add_flexcan(0, NULL);
+ mx28_add_flexcan(1, NULL);
+
+ mx28_add_mxsfb(&m28evk_mxsfb_pdata);
+
+ mx28_add_mxs_mmc(0, &m28evk_mmc_pdata[0]);
+ mx28_add_mxs_mmc(1, &m28evk_mmc_pdata[1]);
+
+ gpio_led_register_device(0, &m28evk_led_data);
+
+ /* I2C */
+ mx28_add_mxs_i2c(0);
+ i2c_register_board_info(0, m28_stk5v3_i2c_boardinfo,
+ ARRAY_SIZE(m28_stk5v3_i2c_boardinfo));
+}
+
+static void __init m28evk_timer_init(void)
+{
+ mx28_clocks_init();
+}
+
+static struct sys_timer m28evk_timer = {
+ .init = m28evk_timer_init,
+};
+
+MACHINE_START(M28EVK, "DENX M28 EVK")
+ .map_io = mx28_map_io,
+ .init_irq = mx28_init_irq,
+ .init_machine = m28evk_init,
+ .timer = &m28evk_timer,
+MACHINE_END
diff --git a/arch/arm/mach-omap2/clock3xxx_data.c b/arch/arm/mach-omap2/clock3xxx_data.c
index ffd55b1..b9b8446 100644
--- a/arch/arm/mach-omap2/clock3xxx_data.c
+++ b/arch/arm/mach-omap2/clock3xxx_data.c
@@ -3078,6 +3078,7 @@
.name = "gpt12_fck",
.ops = &clkops_null,
.parent = &secure_32k_fck,
+ .clkdm_name = "wkup_clkdm",
.recalc = &followparent_recalc,
};
@@ -3085,6 +3086,7 @@
.name = "wdt1_fck",
.ops = &clkops_null,
.parent = &secure_32k_fck,
+ .clkdm_name = "wkup_clkdm",
.recalc = &followparent_recalc,
};
diff --git a/arch/arm/mach-omap2/clock44xx_data.c b/arch/arm/mach-omap2/clock44xx_data.c
index 2af0e3f0..c0b6fbd 100644
--- a/arch/arm/mach-omap2/clock44xx_data.c
+++ b/arch/arm/mach-omap2/clock44xx_data.c
@@ -3376,10 +3376,18 @@
} else if (cpu_is_omap446x()) {
cpu_mask = RATE_IN_4460;
cpu_clkflg = CK_446X;
+ } else {
+ return 0;
}
clk_init(&omap2_clk_functions);
- omap2_clk_disable_clkdm_control();
+
+ /*
+ * Must stay commented until all OMAP SoC drivers are
+ * converted to runtime PM, or drivers may start crashing
+ *
+ * omap2_clk_disable_clkdm_control();
+ */
for (c = omap44xx_clks; c < omap44xx_clks + ARRAY_SIZE(omap44xx_clks);
c++)
diff --git a/arch/arm/mach-omap2/clockdomain.c b/arch/arm/mach-omap2/clockdomain.c
index ab7db08..8f08906 100644
--- a/arch/arm/mach-omap2/clockdomain.c
+++ b/arch/arm/mach-omap2/clockdomain.c
@@ -747,6 +747,7 @@
spin_lock_irqsave(&clkdm->lock, flags);
clkdm->_flags &= ~_CLKDM_FLAG_HWSUP_ENABLED;
ret = arch_clkdm->clkdm_wakeup(clkdm);
+ ret |= pwrdm_state_switch(clkdm->pwrdm.ptr);
spin_unlock_irqrestore(&clkdm->lock, flags);
return ret;
}
@@ -818,6 +819,7 @@
spin_lock_irqsave(&clkdm->lock, flags);
clkdm->_flags &= ~_CLKDM_FLAG_HWSUP_ENABLED;
arch_clkdm->clkdm_deny_idle(clkdm);
+ pwrdm_state_switch(clkdm->pwrdm.ptr);
spin_unlock_irqrestore(&clkdm->lock, flags);
}
diff --git a/arch/arm/mach-omap2/omap_hwmod_2430_data.c b/arch/arm/mach-omap2/omap_hwmod_2430_data.c
index 16743c7..408193d 100644
--- a/arch/arm/mach-omap2/omap_hwmod_2430_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_2430_data.c
@@ -192,6 +192,7 @@
.pa_end = OMAP243X_HS_BASE + SZ_4K - 1,
.flags = ADDR_TYPE_RT
},
+ { }
};
/* l4_core ->usbhsotg interface */
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
index 3feb359..472bf22 100644
--- a/arch/arm/mach-omap2/pm.c
+++ b/arch/arm/mach-omap2/pm.c
@@ -130,7 +130,6 @@
} else {
hwsup = clkdm_in_hwsup(pwrdm->pwrdm_clkdms[0]);
clkdm_wakeup(pwrdm->pwrdm_clkdms[0]);
- pwrdm_wait_transition(pwrdm);
sleep_switch = FORCEWAKEUP_SWITCH;
}
}
@@ -156,7 +155,6 @@
return ret;
}
- pwrdm_wait_transition(pwrdm);
pwrdm_state_switch(pwrdm);
err:
return ret;
diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c
index 9af0847..ef71fdd 100644
--- a/arch/arm/mach-omap2/powerdomain.c
+++ b/arch/arm/mach-omap2/powerdomain.c
@@ -195,28 +195,35 @@
/**
* pwrdm_init - set up the powerdomain layer
- * @pwrdm_list: array of struct powerdomain pointers to register
+ * @pwrdms: array of struct powerdomain pointers to register
* @custom_funcs: func pointers for arch specific implementations
*
- * Loop through the array of powerdomains @pwrdm_list, registering all
- * that are available on the current CPU. If pwrdm_list is supplied
- * and not null, all of the referenced powerdomains will be
- * registered. No return value. XXX pwrdm_list is not really a
- * "list"; it is an array. Rename appropriately.
+ * Loop through the array of powerdomains @pwrdms, registering all
+ * that are available on the current CPU. Also, program all
+ * powerdomain target state as ON; this is to prevent domains from
+ * hitting low power states (if bootloader has target states set to
+ * something other than ON) and potentially even losing context while
+ * PM is not fully initialized. The PM late init code can then program
+ * the desired target state for all the power domains. No return
+ * value.
*/
-void pwrdm_init(struct powerdomain **pwrdm_list, struct pwrdm_ops *custom_funcs)
+void pwrdm_init(struct powerdomain **pwrdms, struct pwrdm_ops *custom_funcs)
{
struct powerdomain **p = NULL;
+ struct powerdomain *temp_p;
if (!custom_funcs)
WARN(1, "powerdomain: No custom pwrdm functions registered\n");
else
arch_pwrdm = custom_funcs;
- if (pwrdm_list) {
- for (p = pwrdm_list; *p; p++)
+ if (pwrdms) {
+ for (p = pwrdms; *p; p++)
_pwrdm_register(*p);
}
+
+ list_for_each_entry(temp_p, &pwrdm_list, node)
+ pwrdm_set_next_pwrst(temp_p, PWRDM_POWER_ON);
}
/**
diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c
index a6eddae..c105556 100644
--- a/arch/arm/mach-orion5x/dns323-setup.c
+++ b/arch/arm/mach-orion5x/dns323-setup.c
@@ -77,7 +77,7 @@
/*
* Check for devices with hard-wired IRQs.
*/
- irq = orion5x_pci_map_irq(const dev, slot, pin);
+ irq = orion5x_pci_map_irq(dev, slot, pin);
if (irq != -1)
return irq;
diff --git a/arch/arm/mach-orion5x/pci.c b/arch/arm/mach-orion5x/pci.c
index 28b8760..bc4a920 100644
--- a/arch/arm/mach-orion5x/pci.c
+++ b/arch/arm/mach-orion5x/pci.c
@@ -14,6 +14,7 @@
#include <linux/pci.h>
#include <linux/slab.h>
#include <linux/mbus.h>
+#include <video/vga.h>
#include <asm/irq.h>
#include <asm/mach/pci.h>
#include <plat/pcie.h>
diff --git a/arch/arm/mach-prima2/clock.c b/arch/arm/mach-prima2/clock.c
index f9a2aaf..615a4e7 100644
--- a/arch/arm/mach-prima2/clock.c
+++ b/arch/arm/mach-prima2/clock.c
@@ -481,6 +481,7 @@
static struct of_device_id clkc_ids[] = {
{ .compatible = "sirf,prima2-clkc" },
+ {},
};
void __init sirfsoc_of_clk_init(void)
diff --git a/arch/arm/mach-prima2/irq.c b/arch/arm/mach-prima2/irq.c
index c3404cb..7af254d 100644
--- a/arch/arm/mach-prima2/irq.c
+++ b/arch/arm/mach-prima2/irq.c
@@ -51,6 +51,7 @@
static struct of_device_id intc_ids[] = {
{ .compatible = "sirf,prima2-intc" },
+ {},
};
void __init sirfsoc_of_irq_init(void)
diff --git a/arch/arm/mach-prima2/rstc.c b/arch/arm/mach-prima2/rstc.c
index d074786..492cfa8 100644
--- a/arch/arm/mach-prima2/rstc.c
+++ b/arch/arm/mach-prima2/rstc.c
@@ -19,6 +19,7 @@
static struct of_device_id rstc_ids[] = {
{ .compatible = "sirf,prima2-rstc" },
+ {},
};
static int __init sirfsoc_of_rstc_init(void)
diff --git a/arch/arm/mach-prima2/timer.c b/arch/arm/mach-prima2/timer.c
index 44027f3..ed7ec48 100644
--- a/arch/arm/mach-prima2/timer.c
+++ b/arch/arm/mach-prima2/timer.c
@@ -190,6 +190,7 @@
static struct of_device_id timer_ids[] = {
{ .compatible = "sirf,prima2-tick" },
+ {},
};
static void __init sirfsoc_of_timer_map(void)
diff --git a/arch/arm/mach-realview/include/mach/system.h b/arch/arm/mach-realview/include/mach/system.h
index a30f2e3..6657ff23 100644
--- a/arch/arm/mach-realview/include/mach/system.h
+++ b/arch/arm/mach-realview/include/mach/system.h
@@ -44,6 +44,7 @@
*/
if (realview_reset)
realview_reset(mode);
+ dsb();
}
#endif
diff --git a/arch/arm/mach-s3c2443/clock.c b/arch/arm/mach-s3c2443/clock.c
index a1a7176..38058af 100644
--- a/arch/arm/mach-s3c2443/clock.c
+++ b/arch/arm/mach-s3c2443/clock.c
@@ -128,7 +128,7 @@
unsigned long clkcon0;
clkcon0 = __raw_readl(S3C2443_CLKDIV0);
- clkcon0 &= S3C2443_CLKDIV0_ARMDIV_MASK;
+ clkcon0 &= ~S3C2443_CLKDIV0_ARMDIV_MASK;
clkcon0 |= val << S3C2443_CLKDIV0_ARMDIV_SHIFT;
__raw_writel(clkcon0, S3C2443_CLKDIV0);
}
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c64xx/mach-smdk6410.c
index ecbea92..a9f3183 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6410.c
@@ -262,45 +262,6 @@
.cols = 8,
};
-static int smdk6410_backlight_init(struct device *dev)
-{
- int ret;
-
- ret = gpio_request(S3C64XX_GPF(15), "Backlight");
- if (ret) {
- printk(KERN_ERR "failed to request GPF for PWM-OUT1\n");
- return ret;
- }
-
- /* Configure GPIO pin with S3C64XX_GPF15_PWM_TOUT1 */
- s3c_gpio_cfgpin(S3C64XX_GPF(15), S3C_GPIO_SFN(2));
-
- return 0;
-}
-
-static void smdk6410_backlight_exit(struct device *dev)
-{
- s3c_gpio_cfgpin(S3C64XX_GPF(15), S3C_GPIO_OUTPUT);
- gpio_free(S3C64XX_GPF(15));
-}
-
-static struct platform_pwm_backlight_data smdk6410_backlight_data = {
- .pwm_id = 1,
- .max_brightness = 255,
- .dft_brightness = 255,
- .pwm_period_ns = 78770,
- .init = smdk6410_backlight_init,
- .exit = smdk6410_backlight_exit,
-};
-
-static struct platform_device smdk6410_backlight_device = {
- .name = "pwm-backlight",
- .dev = {
- .parent = &s3c_device_timer[1].dev,
- .platform_data = &smdk6410_backlight_data,
- },
-};
-
static struct map_desc smdk6410_iodesc[] = {};
static struct platform_device *smdk6410_devices[] __initdata = {
diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c64xx/pm.c
index 8bad643..055e285 100644
--- a/arch/arm/mach-s3c64xx/pm.c
+++ b/arch/arm/mach-s3c64xx/pm.c
@@ -16,6 +16,7 @@
#include <linux/suspend.h>
#include <linux/serial_core.h>
#include <linux/io.h>
+#include <linux/gpio.h>
#include <mach/map.h>
#include <mach/irqs.h>
diff --git a/arch/arm/mach-s5p64x0/irq-eint.c b/arch/arm/mach-s5p64x0/irq-eint.c
index 69ed454..fe7380f 100644
--- a/arch/arm/mach-s5p64x0/irq-eint.c
+++ b/arch/arm/mach-s5p64x0/irq-eint.c
@@ -129,7 +129,7 @@
}
ct = gc->chip_types;
- ct->chip.irq_ack = irq_gc_ack;
+ ct->chip.irq_ack = irq_gc_ack_set_bit;
ct->chip.irq_mask = irq_gc_mask_set_bit;
ct->chip.irq_unmask = irq_gc_mask_clr_bit;
ct->chip.irq_set_type = s5p64x0_irq_eint_set_type;
diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c
index 52a8e60..f5f8fa8 100644
--- a/arch/arm/mach-s5pv210/clock.c
+++ b/arch/arm/mach-s5pv210/clock.c
@@ -815,8 +815,7 @@
.reg_div = { .reg = S5P_CLK_DIV3, .shift = 20, .size = 4 },
}, {
.clk = {
- .name = "sclk_cam",
- .devname = "s5pv210-fimc.0",
+ .name = "sclk_cam0",
.enable = s5pv210_clk_mask0_ctrl,
.ctrlbit = (1 << 3),
},
@@ -825,8 +824,7 @@
.reg_div = { .reg = S5P_CLK_DIV1, .shift = 12, .size = 4 },
}, {
.clk = {
- .name = "sclk_cam",
- .devname = "s5pv210-fimc.1",
+ .name = "sclk_cam1",
.enable = s5pv210_clk_mask0_ctrl,
.ctrlbit = (1 << 4),
},
diff --git a/arch/arm/mach-s5pv210/pm.c b/arch/arm/mach-s5pv210/pm.c
index 309e388..f149d27 100644
--- a/arch/arm/mach-s5pv210/pm.c
+++ b/arch/arm/mach-s5pv210/pm.c
@@ -88,7 +88,7 @@
SAVE_ITEM(S3C2410_TCNTO(0)),
};
-void s5pv210_cpu_suspend(unsigned long arg)
+static int s5pv210_cpu_suspend(unsigned long arg)
{
unsigned long tmp;
diff --git a/arch/arm/mach-shmobile/board-ag5evm.c b/arch/arm/mach-shmobile/board-ag5evm.c
index ce5c251..cdfdd62 100644
--- a/arch/arm/mach-shmobile/board-ag5evm.c
+++ b/arch/arm/mach-shmobile/board-ag5evm.c
@@ -341,6 +341,7 @@
static struct sh_mobile_sdhi_info sdhi0_info = {
.dma_slave_tx = SHDMA_SLAVE_SDHI0_TX,
.dma_slave_rx = SHDMA_SLAVE_SDHI0_RX,
+ .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
.tmio_caps = MMC_CAP_SD_HIGHSPEED,
.tmio_ocr_mask = MMC_VDD_27_28 | MMC_VDD_28_29,
};
@@ -382,7 +383,7 @@
}
static struct sh_mobile_sdhi_info sh_sdhi1_info = {
- .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE,
+ .tmio_flags = TMIO_MMC_WRPROTECT_DISABLE | TMIO_MMC_HAS_IDLE_WAIT,
.tmio_caps = MMC_CAP_NONREMOVABLE | MMC_CAP_SDIO_IRQ,
.tmio_ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.set_pwr = ag5evm_sdhi1_set_pwr,
diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c
index 9e0856b..523f608 100644
--- a/arch/arm/mach-shmobile/board-ap4evb.c
+++ b/arch/arm/mach-shmobile/board-ap4evb.c
@@ -1412,6 +1412,7 @@
fsi_init_pm_clock();
sh7372_pm_init();
pm_clk_add(&fsi_device.dev, "spu2");
+ pm_clk_add(&lcdc1_device.dev, "hdmi");
}
static void __init ap4evb_timer_init(void)
diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index d41c01f..17c19dc 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -641,6 +641,8 @@
},
.driver_param = {
.buswait_bwait = 4,
+ .d0_tx_id = SHDMA_SLAVE_USB0_TX,
+ .d1_rx_id = SHDMA_SLAVE_USB0_RX,
},
},
};
@@ -810,6 +812,8 @@
.buswait_bwait = 4,
.pipe_type = usbhs1_pipe_cfg,
.pipe_size = ARRAY_SIZE(usbhs1_pipe_cfg),
+ .d0_tx_id = SHDMA_SLAVE_USB1_TX,
+ .d1_rx_id = SHDMA_SLAVE_USB1_RX,
},
},
};
@@ -1588,6 +1592,7 @@
hdmi_init_pm_clock();
sh7372_pm_init();
pm_clk_add(&fsi_device.dev, "spu2");
+ pm_clk_add(&hdmi_lcdc_device.dev, "hdmi");
}
static void __init mackerel_timer_init(void)
diff --git a/arch/arm/mach-shmobile/clock-sh7372.c b/arch/arm/mach-shmobile/clock-sh7372.c
index 6b1619a..6697592 100644
--- a/arch/arm/mach-shmobile/clock-sh7372.c
+++ b/arch/arm/mach-shmobile/clock-sh7372.c
@@ -503,16 +503,17 @@
&sh7372_fsidivb_clk,
};
-enum { MSTP001,
+enum { MSTP001, MSTP000,
MSTP131, MSTP130,
MSTP129, MSTP128, MSTP127, MSTP126, MSTP125,
MSTP118, MSTP117, MSTP116, MSTP113,
MSTP106, MSTP101, MSTP100,
MSTP223,
- MSTP218, MSTP217, MSTP216,
- MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
- MSTP329, MSTP328, MSTP323, MSTP322, MSTP314, MSTP313, MSTP312,
- MSTP423, MSTP415, MSTP413, MSTP411, MSTP410, MSTP406, MSTP403,
+ MSTP218, MSTP217, MSTP216, MSTP214, MSTP208, MSTP207,
+ MSTP206, MSTP205, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
+ MSTP328, MSTP323, MSTP322, MSTP314, MSTP313, MSTP312,
+ MSTP423, MSTP415, MSTP413, MSTP411, MSTP410, MSTP407, MSTP406,
+ MSTP405, MSTP404, MSTP403, MSTP400,
MSTP_NR };
#define MSTP(_parent, _reg, _bit, _flags) \
@@ -520,6 +521,7 @@
static struct clk mstp_clks[MSTP_NR] = {
[MSTP001] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR0, 1, 0), /* IIC2 */
+ [MSTP000] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR0, 0, 0), /* MSIOF0 */
[MSTP131] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 31, 0), /* VEU3 */
[MSTP130] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 30, 0), /* VEU2 */
[MSTP129] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 29, 0), /* VEU1 */
@@ -538,14 +540,16 @@
[MSTP218] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* DMAC1 */
[MSTP217] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 17, 0), /* DMAC2 */
[MSTP216] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 16, 0), /* DMAC3 */
+ [MSTP214] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 14, 0), /* USBDMAC */
+ [MSTP208] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 8, 0), /* MSIOF1 */
[MSTP207] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */
[MSTP206] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */
+ [MSTP205] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 5, 0), /* MSIOF2 */
[MSTP204] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */
[MSTP203] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 3, 0), /* SCIFA1 */
[MSTP202] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 2, 0), /* SCIFA2 */
[MSTP201] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 1, 0), /* SCIFA3 */
[MSTP200] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 0, 0), /* SCIFA4 */
- [MSTP329] = MSTP(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */
[MSTP328] = MSTP(&div6_clks[DIV6_SPU], SMSTPCR3, 28, 0), /* FSI2 */
[MSTP323] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 23, 0), /* IIC1 */
[MSTP322] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 22, 0), /* USB0 */
@@ -557,8 +561,12 @@
[MSTP413] = MSTP(&pllc1_div2_clk, SMSTPCR4, 13, 0), /* HDMI */
[MSTP411] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR4, 11, 0), /* IIC3 */
[MSTP410] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR4, 10, 0), /* IIC4 */
+ [MSTP407] = MSTP(&div4_clks[DIV4_HP], SMSTPCR4, 7, 0), /* USB-DMAC1 */
[MSTP406] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR4, 6, 0), /* USB1 */
+ [MSTP405] = MSTP(&r_clk, SMSTPCR4, 5, 0), /* CMT4 */
+ [MSTP404] = MSTP(&r_clk, SMSTPCR4, 4, 0), /* CMT3 */
[MSTP403] = MSTP(&r_clk, SMSTPCR4, 3, 0), /* KEYSC */
+ [MSTP400] = MSTP(&r_clk, SMSTPCR4, 0, 0), /* CMT2 */
};
static struct clk_lookup lookups[] = {
@@ -609,6 +617,7 @@
/* MSTP32 clocks */
CLKDEV_DEV_ID("i2c-sh_mobile.2", &mstp_clks[MSTP001]), /* IIC2 */
+ CLKDEV_DEV_ID("spi_sh_msiof.0", &mstp_clks[MSTP000]), /* MSIOF0 */
CLKDEV_DEV_ID("uio_pdrv_genirq.4", &mstp_clks[MSTP131]), /* VEU3 */
CLKDEV_DEV_ID("uio_pdrv_genirq.3", &mstp_clks[MSTP130]), /* VEU2 */
CLKDEV_DEV_ID("uio_pdrv_genirq.2", &mstp_clks[MSTP129]), /* VEU1 */
@@ -629,14 +638,16 @@
CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]), /* DMAC1 */
CLKDEV_DEV_ID("sh-dma-engine.1", &mstp_clks[MSTP217]), /* DMAC2 */
CLKDEV_DEV_ID("sh-dma-engine.2", &mstp_clks[MSTP216]), /* DMAC3 */
+ CLKDEV_DEV_ID("sh-dma-engine.3", &mstp_clks[MSTP214]), /* USB-DMAC0 */
+ CLKDEV_DEV_ID("spi_sh_msiof.1", &mstp_clks[MSTP208]), /* MSIOF1 */
CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
CLKDEV_DEV_ID("sh-sci.6", &mstp_clks[MSTP206]), /* SCIFB */
+ CLKDEV_DEV_ID("spi_sh_msiof.2", &mstp_clks[MSTP205]), /* MSIOF2 */
CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */
CLKDEV_DEV_ID("sh-sci.2", &mstp_clks[MSTP202]), /* SCIFA2 */
CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP201]), /* SCIFA3 */
CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP200]), /* SCIFA4 */
- CLKDEV_DEV_ID("sh_cmt.10", &mstp_clks[MSTP329]), /* CMT10 */
CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]), /* FSI2 */
CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]), /* IIC1 */
CLKDEV_DEV_ID("r8a66597_hcd.0", &mstp_clks[MSTP322]), /* USB0 */
@@ -650,11 +661,17 @@
CLKDEV_DEV_ID("sh-mobile-hdmi", &mstp_clks[MSTP413]), /* HDMI */
CLKDEV_DEV_ID("i2c-sh_mobile.3", &mstp_clks[MSTP411]), /* IIC3 */
CLKDEV_DEV_ID("i2c-sh_mobile.4", &mstp_clks[MSTP410]), /* IIC4 */
+ CLKDEV_DEV_ID("sh-dma-engine.4", &mstp_clks[MSTP407]), /* USB-DMAC1 */
CLKDEV_DEV_ID("r8a66597_hcd.1", &mstp_clks[MSTP406]), /* USB1 */
CLKDEV_DEV_ID("r8a66597_udc.1", &mstp_clks[MSTP406]), /* USB1 */
CLKDEV_DEV_ID("renesas_usbhs.1", &mstp_clks[MSTP406]), /* USB1 */
+ CLKDEV_DEV_ID("sh_cmt.4", &mstp_clks[MSTP405]), /* CMT4 */
+ CLKDEV_DEV_ID("sh_cmt.3", &mstp_clks[MSTP404]), /* CMT3 */
CLKDEV_DEV_ID("sh_keysc.0", &mstp_clks[MSTP403]), /* KEYSC */
+ CLKDEV_DEV_ID("sh_cmt.2", &mstp_clks[MSTP400]), /* CMT2 */
+ CLKDEV_ICK_ID("hdmi", "sh_mobile_lcdc_fb.1",
+ &div6_reparent_clks[DIV6_HDMI]),
CLKDEV_ICK_ID("ick", "sh-mobile-hdmi", &div6_reparent_clks[DIV6_HDMI]),
CLKDEV_ICK_ID("icka", "sh_fsi2", &div6_reparent_clks[DIV6_FSIA]),
CLKDEV_ICK_ID("ickb", "sh_fsi2", &div6_reparent_clks[DIV6_FSIB]),
diff --git a/arch/arm/mach-shmobile/clock-sh73a0.c b/arch/arm/mach-shmobile/clock-sh73a0.c
index 6db2cca..61a846b 100644
--- a/arch/arm/mach-shmobile/clock-sh73a0.c
+++ b/arch/arm/mach-shmobile/clock-sh73a0.c
@@ -365,7 +365,7 @@
__raw_writel(0x108, SD2CKCR);
/* detect main clock parent */
- switch ((__raw_readl(CKSCR) >> 24) & 0x03) {
+ switch ((__raw_readl(CKSCR) >> 28) & 0x03) {
case 0:
main_clk.parent = &sh73a0_extal1_clk;
break;
diff --git a/arch/arm/mach-shmobile/include/mach/sh7372.h b/arch/arm/mach-shmobile/include/mach/sh7372.h
index ce595ce..24e63a8 100644
--- a/arch/arm/mach-shmobile/include/mach/sh7372.h
+++ b/arch/arm/mach-shmobile/include/mach/sh7372.h
@@ -459,6 +459,10 @@
SHDMA_SLAVE_SDHI2_TX,
SHDMA_SLAVE_MMCIF_RX,
SHDMA_SLAVE_MMCIF_TX,
+ SHDMA_SLAVE_USB0_TX,
+ SHDMA_SLAVE_USB0_RX,
+ SHDMA_SLAVE_USB1_TX,
+ SHDMA_SLAVE_USB1_RX,
};
extern struct clk sh7372_extal1_clk;
diff --git a/arch/arm/mach-shmobile/intc-sh7372.c b/arch/arm/mach-shmobile/intc-sh7372.c
index 3b28743..739315e3 100644
--- a/arch/arm/mach-shmobile/intc-sh7372.c
+++ b/arch/arm/mach-shmobile/intc-sh7372.c
@@ -379,7 +379,7 @@
/* BBIF2 */
VPU,
TSIF1,
- _3DG_SGX530,
+ /* 3DG */
_2DDMAC,
IIC2_ALI2, IIC2_TACKI2, IIC2_WAITI2, IIC2_DTEI2,
IPMMU_IPMMUR, IPMMU_IPMMUR2,
@@ -436,7 +436,7 @@
/* BBIF2 */
INTCS_VECT(VPU, 0x980),
INTCS_VECT(TSIF1, 0x9a0),
- INTCS_VECT(_3DG_SGX530, 0x9e0),
+ /* 3DG */
INTCS_VECT(_2DDMAC, 0xa00),
INTCS_VECT(IIC2_ALI2, 0xa80), INTCS_VECT(IIC2_TACKI2, 0xaa0),
INTCS_VECT(IIC2_WAITI2, 0xac0), INTCS_VECT(IIC2_DTEI2, 0xae0),
@@ -521,7 +521,7 @@
RTDMAC_1_DEI3, RTDMAC_1_DEI2, RTDMAC_1_DEI1, RTDMAC_1_DEI0 } },
{ 0xffd20198, 0xffd201d8, 8, /* IMR6SA / IMCR6SA */
{ 0, 0, MSIOF, 0,
- _3DG_SGX530, 0, 0, 0 } },
+ 0, 0, 0, 0 } },
{ 0xffd2019c, 0xffd201dc, 8, /* IMR7SA / IMCR7SA */
{ 0, TMU_TUNI2, TMU_TUNI1, TMU_TUNI0,
0, 0, 0, 0 } },
@@ -561,7 +561,6 @@
TMU_TUNI2, TSIF1 } },
{ 0xffd2001c, 0, 16, 4, /* IPRHS */ { 0, 0, VEU, BEU } },
{ 0xffd20020, 0, 16, 4, /* IPRIS */ { 0, MSIOF, TSIF0, IIC0 } },
- { 0xffd20024, 0, 16, 4, /* IPRJS */ { 0, _3DG_SGX530, 0, 0 } },
{ 0xffd20028, 0, 16, 4, /* IPRKS */ { 0, 0, LMB, 0 } },
{ 0xffd2002c, 0, 16, 4, /* IPRLS */ { IPMMU, 0, 0, 0 } },
{ 0xffd20030, 0, 16, 4, /* IPRMS */ { IIC2, 0, 0, 0 } },
diff --git a/arch/arm/mach-shmobile/setup-sh7372.c b/arch/arm/mach-shmobile/setup-sh7372.c
index 79f0413..2d9b1b1 100644
--- a/arch/arm/mach-shmobile/setup-sh7372.c
+++ b/arch/arm/mach-shmobile/setup-sh7372.c
@@ -169,35 +169,35 @@
};
/* CMT */
-static struct sh_timer_config cmt10_platform_data = {
- .name = "CMT10",
- .channel_offset = 0x10,
- .timer_bit = 0,
+static struct sh_timer_config cmt2_platform_data = {
+ .name = "CMT2",
+ .channel_offset = 0x40,
+ .timer_bit = 5,
.clockevent_rating = 125,
.clocksource_rating = 125,
};
-static struct resource cmt10_resources[] = {
+static struct resource cmt2_resources[] = {
[0] = {
- .name = "CMT10",
- .start = 0xe6138010,
- .end = 0xe613801b,
+ .name = "CMT2",
+ .start = 0xe6130040,
+ .end = 0xe613004b,
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = evt2irq(0x0b00), /* CMT1_CMT10 */
+ .start = evt2irq(0x0b80), /* CMT2 */
.flags = IORESOURCE_IRQ,
},
};
-static struct platform_device cmt10_device = {
+static struct platform_device cmt2_device = {
.name = "sh_cmt",
- .id = 10,
+ .id = 2,
.dev = {
- .platform_data = &cmt10_platform_data,
+ .platform_data = &cmt2_platform_data,
},
- .resource = cmt10_resources,
- .num_resources = ARRAY_SIZE(cmt10_resources),
+ .resource = cmt2_resources,
+ .num_resources = ARRAY_SIZE(cmt2_resources),
};
/* TMU */
@@ -602,6 +602,150 @@
},
};
+/*
+ * USB-DMAC
+ */
+
+unsigned int usbts_shift[] = {3, 4, 5};
+
+enum {
+ XMIT_SZ_8BYTE = 0,
+ XMIT_SZ_16BYTE = 1,
+ XMIT_SZ_32BYTE = 2,
+};
+
+#define USBTS_INDEX2VAL(i) (((i) & 3) << 6)
+
+static const struct sh_dmae_channel sh7372_usb_dmae_channels[] = {
+ {
+ .offset = 0,
+ }, {
+ .offset = 0x20,
+ },
+};
+
+/* USB DMAC0 */
+static const struct sh_dmae_slave_config sh7372_usb_dmae0_slaves[] = {
+ {
+ .slave_id = SHDMA_SLAVE_USB0_TX,
+ .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE),
+ }, {
+ .slave_id = SHDMA_SLAVE_USB0_RX,
+ .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE),
+ },
+};
+
+static struct sh_dmae_pdata usb_dma0_platform_data = {
+ .slave = sh7372_usb_dmae0_slaves,
+ .slave_num = ARRAY_SIZE(sh7372_usb_dmae0_slaves),
+ .channel = sh7372_usb_dmae_channels,
+ .channel_num = ARRAY_SIZE(sh7372_usb_dmae_channels),
+ .ts_low_shift = 6,
+ .ts_low_mask = 0xc0,
+ .ts_high_shift = 0,
+ .ts_high_mask = 0,
+ .ts_shift = usbts_shift,
+ .ts_shift_num = ARRAY_SIZE(usbts_shift),
+ .dmaor_init = DMAOR_DME,
+ .chcr_offset = 0x14,
+ .chcr_ie_bit = 1 << 5,
+ .dmaor_is_32bit = 1,
+ .needs_tend_set = 1,
+ .no_dmars = 1,
+};
+
+static struct resource sh7372_usb_dmae0_resources[] = {
+ {
+ /* Channel registers and DMAOR */
+ .start = 0xe68a0020,
+ .end = 0xe68a0064 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ /* VCR/SWR/DMICR */
+ .start = 0xe68a0000,
+ .end = 0xe68a0014 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ /* IRQ for channels */
+ .start = evt2irq(0x0a00),
+ .end = evt2irq(0x0a00),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device usb_dma0_device = {
+ .name = "sh-dma-engine",
+ .id = 3,
+ .resource = sh7372_usb_dmae0_resources,
+ .num_resources = ARRAY_SIZE(sh7372_usb_dmae0_resources),
+ .dev = {
+ .platform_data = &usb_dma0_platform_data,
+ },
+};
+
+/* USB DMAC1 */
+static const struct sh_dmae_slave_config sh7372_usb_dmae1_slaves[] = {
+ {
+ .slave_id = SHDMA_SLAVE_USB1_TX,
+ .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE),
+ }, {
+ .slave_id = SHDMA_SLAVE_USB1_RX,
+ .chcr = USBTS_INDEX2VAL(XMIT_SZ_8BYTE),
+ },
+};
+
+static struct sh_dmae_pdata usb_dma1_platform_data = {
+ .slave = sh7372_usb_dmae1_slaves,
+ .slave_num = ARRAY_SIZE(sh7372_usb_dmae1_slaves),
+ .channel = sh7372_usb_dmae_channels,
+ .channel_num = ARRAY_SIZE(sh7372_usb_dmae_channels),
+ .ts_low_shift = 6,
+ .ts_low_mask = 0xc0,
+ .ts_high_shift = 0,
+ .ts_high_mask = 0,
+ .ts_shift = usbts_shift,
+ .ts_shift_num = ARRAY_SIZE(usbts_shift),
+ .dmaor_init = DMAOR_DME,
+ .chcr_offset = 0x14,
+ .chcr_ie_bit = 1 << 5,
+ .dmaor_is_32bit = 1,
+ .needs_tend_set = 1,
+ .no_dmars = 1,
+};
+
+static struct resource sh7372_usb_dmae1_resources[] = {
+ {
+ /* Channel registers and DMAOR */
+ .start = 0xe68c0020,
+ .end = 0xe68c0064 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ /* VCR/SWR/DMICR */
+ .start = 0xe68c0000,
+ .end = 0xe68c0014 - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ /* IRQ for channels */
+ .start = evt2irq(0x1d00),
+ .end = evt2irq(0x1d00),
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device usb_dma1_device = {
+ .name = "sh-dma-engine",
+ .id = 4,
+ .resource = sh7372_usb_dmae1_resources,
+ .num_resources = ARRAY_SIZE(sh7372_usb_dmae1_resources),
+ .dev = {
+ .platform_data = &usb_dma1_platform_data,
+ },
+};
+
/* VPU */
static struct uio_info vpu_platform_data = {
.name = "VPU5HG",
@@ -818,7 +962,7 @@
&scif4_device,
&scif5_device,
&scif6_device,
- &cmt10_device,
+ &cmt2_device,
&tmu00_device,
&tmu01_device,
};
@@ -829,6 +973,8 @@
&dma0_device,
&dma1_device,
&dma2_device,
+ &usb_dma0_device,
+ &usb_dma1_device,
&vpu_device,
&veu0_device,
&veu1_device,
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index 9e6b93b..d0d267a 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -318,6 +318,10 @@
.rate = 1000000,
};
+static struct clk v2m_ref_clk = {
+ .rate = 32768,
+};
+
static struct clk dummy_apb_pclk;
static struct clk_lookup v2m_lookups[] = {
@@ -348,6 +352,9 @@
}, { /* CLCD */
.dev_id = "mb:clcd",
.clk = &osc1_clk,
+ }, { /* SP805 WDT */
+ .dev_id = "mb:wdt",
+ .clk = &v2m_ref_clk,
}, { /* SP804 timers */
.dev_id = "sp804",
.con_id = "v2m-timer0",
diff --git a/arch/arm/mm/abort-macro.S b/arch/arm/mm/abort-macro.S
index 52162d5..2cbf68e 100644
--- a/arch/arm/mm/abort-macro.S
+++ b/arch/arm/mm/abort-macro.S
@@ -17,7 +17,7 @@
cmp \tmp, # 0x5600 @ Is it ldrsb?
orreq \tmp, \tmp, #1 << 11 @ Set L-bit if yes
tst \tmp, #1 << 11 @ L = 0 -> write
- orreq \psr, \psr, #1 << 11 @ yes.
+ orreq \fsr, \fsr, #1 << 11 @ yes.
b do_DataAbort
not_thumb:
.endm
diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c
index 44c0867..9ecfdb5 100644
--- a/arch/arm/mm/cache-l2x0.c
+++ b/arch/arm/mm/cache-l2x0.c
@@ -277,6 +277,25 @@
spin_unlock_irqrestore(&l2x0_lock, flags);
}
+static void __init l2x0_unlock(__u32 cache_id)
+{
+ int lockregs;
+ int i;
+
+ if (cache_id == L2X0_CACHE_ID_PART_L310)
+ lockregs = 8;
+ else
+ /* L210 and unknown types */
+ lockregs = 1;
+
+ for (i = 0; i < lockregs; i++) {
+ writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
+ i * L2X0_LOCKDOWN_STRIDE);
+ writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
+ i * L2X0_LOCKDOWN_STRIDE);
+ }
+}
+
void __init l2x0_init(void __iomem *base, __u32 aux_val, __u32 aux_mask)
{
__u32 aux;
@@ -328,6 +347,8 @@
* accessing the below registers will fault.
*/
if (!(readl_relaxed(l2x0_base + L2X0_CTRL) & 1)) {
+ /* Make sure that I&D is not locked down when starting */
+ l2x0_unlock(cache_id);
/* l2x0 controller is disabled */
writel_relaxed(aux, l2x0_base + L2X0_AUX_CTRL);
diff --git a/arch/arm/mm/cache-v7.S b/arch/arm/mm/cache-v7.S
index 3b24bfa..07c4bc8 100644
--- a/arch/arm/mm/cache-v7.S
+++ b/arch/arm/mm/cache-v7.S
@@ -174,6 +174,10 @@
dcache_line_size r2, r3
sub r3, r2, #1
bic r12, r0, r3
+#ifdef CONFIG_ARM_ERRATA_764369
+ ALT_SMP(W(dsb))
+ ALT_UP(W(nop))
+#endif
1:
USER( mcr p15, 0, r12, c7, c11, 1 ) @ clean D line to the point of unification
add r12, r12, r2
@@ -223,6 +227,10 @@
add r1, r0, r1
sub r3, r2, #1
bic r0, r0, r3
+#ifdef CONFIG_ARM_ERRATA_764369
+ ALT_SMP(W(dsb))
+ ALT_UP(W(nop))
+#endif
1:
mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D line / unified line
add r0, r0, r2
@@ -247,6 +255,10 @@
sub r3, r2, #1
tst r0, r3
bic r0, r0, r3
+#ifdef CONFIG_ARM_ERRATA_764369
+ ALT_SMP(W(dsb))
+ ALT_UP(W(nop))
+#endif
mcrne p15, 0, r0, c7, c14, 1 @ clean & invalidate D / U line
tst r1, r3
@@ -270,6 +282,10 @@
dcache_line_size r2, r3
sub r3, r2, #1
bic r0, r0, r3
+#ifdef CONFIG_ARM_ERRATA_764369
+ ALT_SMP(W(dsb))
+ ALT_UP(W(nop))
+#endif
1:
mcr p15, 0, r0, c7, c10, 1 @ clean D / U line
add r0, r0, r2
@@ -288,6 +304,10 @@
dcache_line_size r2, r3
sub r3, r2, #1
bic r0, r0, r3
+#ifdef CONFIG_ARM_ERRATA_764369
+ ALT_SMP(W(dsb))
+ ALT_UP(W(nop))
+#endif
1:
mcr p15, 0, r0, c7, c14, 1 @ clean & invalidate D / U line
add r0, r0, r2
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index 0a0a1e7..c3ff82f 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -324,6 +324,8 @@
if (addr)
*handle = pfn_to_dma(dev, page_to_pfn(page));
+ else
+ __dma_free_buffer(page, size);
return addr;
}
diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
index 91bca35..cc7e2d8 100644
--- a/arch/arm/mm/init.c
+++ b/arch/arm/mm/init.c
@@ -298,7 +298,7 @@
#ifdef CONFIG_HAVE_ARCH_PFN_VALID
int pfn_valid(unsigned long pfn)
{
- return memblock_is_memory(pfn << PAGE_SHIFT);
+ return memblock_is_memory(__pfn_to_phys(pfn));
}
EXPORT_SYMBOL(pfn_valid);
#endif
diff --git a/arch/arm/mm/proc-arm920.S b/arch/arm/mm/proc-arm920.S
index 92bd102..2e6849b 100644
--- a/arch/arm/mm/proc-arm920.S
+++ b/arch/arm/mm/proc-arm920.S
@@ -379,7 +379,7 @@
/* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */
.globl cpu_arm920_suspend_size
-.equ cpu_arm920_suspend_size, 4 * 3
+.equ cpu_arm920_suspend_size, 4 * 4
#ifdef CONFIG_PM_SLEEP
ENTRY(cpu_arm920_do_suspend)
stmfd sp!, {r4 - r7, lr}
diff --git a/arch/arm/mm/proc-arm926.S b/arch/arm/mm/proc-arm926.S
index 2bbcf05..cd8f79c 100644
--- a/arch/arm/mm/proc-arm926.S
+++ b/arch/arm/mm/proc-arm926.S
@@ -394,7 +394,7 @@
/* Suspend/resume support: taken from arch/arm/plat-s3c24xx/sleep.S */
.globl cpu_arm926_suspend_size
-.equ cpu_arm926_suspend_size, 4 * 3
+.equ cpu_arm926_suspend_size, 4 * 4
#ifdef CONFIG_PM_SLEEP
ENTRY(cpu_arm926_do_suspend)
stmfd sp!, {r4 - r7, lr}
diff --git a/arch/arm/mm/proc-sa1100.S b/arch/arm/mm/proc-sa1100.S
index 07219c2..69e7f2e 100644
--- a/arch/arm/mm/proc-sa1100.S
+++ b/arch/arm/mm/proc-sa1100.S
@@ -182,11 +182,11 @@
ENTRY(cpu_sa1100_do_resume)
ldmia r0, {r4 - r7} @ load cp regs
- mov r1, #0
- mcr p15, 0, r1, c8, c7, 0 @ flush I+D TLBs
- mcr p15, 0, r1, c7, c7, 0 @ flush I&D cache
- mcr p15, 0, r1, c9, c0, 0 @ invalidate RB
- mcr p15, 0, r1, c9, c0, 5 @ allow user space to use RB
+ mov ip, #0
+ mcr p15, 0, ip, c8, c7, 0 @ flush I+D TLBs
+ mcr p15, 0, ip, c7, c7, 0 @ flush I&D cache
+ mcr p15, 0, ip, c9, c0, 0 @ invalidate RB
+ mcr p15, 0, ip, c9, c0, 5 @ allow user space to use RB
mcr p15, 0, r4, c3, c0, 0 @ domain ID
mcr p15, 0, r5, c2, c0, 0 @ translation table base addr
diff --git a/arch/arm/mm/proc-v6.S b/arch/arm/mm/proc-v6.S
index 219138d..a923aa0 100644
--- a/arch/arm/mm/proc-v6.S
+++ b/arch/arm/mm/proc-v6.S
@@ -223,6 +223,22 @@
mrc p15, 0, r0, c1, c0, 0 @ read control register
bic r0, r0, r5 @ clear bits them
orr r0, r0, r6 @ set them
+#ifdef CONFIG_ARM_ERRATA_364296
+ /*
+ * Workaround for the 364296 ARM1136 r0p2 erratum (possible cache data
+ * corruption with hit-under-miss enabled). The conditional code below
+ * (setting the undocumented bit 31 in the auxiliary control register
+ * and the FI bit in the control register) disables hit-under-miss
+ * without putting the processor into full low interrupt latency mode.
+ */
+ ldr r6, =0x4107b362 @ id for ARM1136 r0p2
+ mrc p15, 0, r5, c0, c0, 0 @ get processor id
+ teq r5, r6 @ check for the faulty core
+ mrceq p15, 0, r5, c1, c0, 1 @ load aux control reg
+ orreq r5, r5, #(1 << 31) @ set the undocumented bit 31
+ mcreq p15, 0, r5, c1, c0, 1 @ write aux control reg
+ orreq r0, r0, #(1 << 21) @ low interrupt latency configuration
+#endif
mov pc, lr @ return to head.S:__ret
/*
diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S
index a30e785..9049c07 100644
--- a/arch/arm/mm/proc-v7.S
+++ b/arch/arm/mm/proc-v7.S
@@ -66,6 +66,7 @@
ENTRY(cpu_v7_reset)
mrc p15, 0, r1, c1, c0, 0 @ ctrl register
bic r1, r1, #0x1 @ ...............m
+ THUMB( bic r1, r1, #1 << 30 ) @ SCTLR.TE (Thumb exceptions)
mcr p15, 0, r1, c1, c0, 0 @ disable MMU
isb
mov pc, r0
@@ -247,13 +248,16 @@
mcr p15, 0, r7, c2, c0, 0 @ TTB 0
mcr p15, 0, r8, c2, c0, 1 @ TTB 1
mcr p15, 0, ip, c2, c0, 2 @ TTB control register
- mcr p15, 0, r10, c1, c0, 1 @ Auxiliary control register
+ mrc p15, 0, r4, c1, c0, 1 @ Read Auxiliary control register
+ teq r4, r10 @ Is it already set?
+ mcrne p15, 0, r10, c1, c0, 1 @ No, so write it
mcr p15, 0, r11, c1, c0, 2 @ Co-processor access control
ldr r4, =PRRR @ PRRR
ldr r5, =NMRR @ NMRR
mcr p15, 0, r4, c10, c2, 0 @ write PRRR
mcr p15, 0, r5, c10, c2, 1 @ write NMRR
isb
+ dsb
mov r0, r9 @ control register
mov r2, r7, lsr #14 @ get TTB0 base
mov r2, r2, lsl #14
diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S
index 28c72a2..755e1bf 100644
--- a/arch/arm/mm/proc-xsc3.S
+++ b/arch/arm/mm/proc-xsc3.S
@@ -406,7 +406,7 @@
.align
.globl cpu_xsc3_suspend_size
-.equ cpu_xsc3_suspend_size, 4 * 8
+.equ cpu_xsc3_suspend_size, 4 * 7
#ifdef CONFIG_PM_SLEEP
ENTRY(cpu_xsc3_do_suspend)
stmfd sp!, {r4 - r10, lr}
@@ -418,12 +418,12 @@
mrc p15, 0, r9, c1, c0, 1 @ auxiliary control reg
mrc p15, 0, r10, c1, c0, 0 @ control reg
bic r4, r4, #2 @ clear frequency change bit
- stmia r0, {r1, r4 - r10} @ store v:p offset + cp regs
+ stmia r0, {r4 - r10} @ store cp regs
ldmia sp!, {r4 - r10, pc}
ENDPROC(cpu_xsc3_do_suspend)
ENTRY(cpu_xsc3_do_resume)
- ldmia r0, {r1, r4 - r10} @ load v:p offset + cp regs
+ ldmia r0, {r4 - r10} @ load cp regs
mov ip, #0
mcr p15, 0, ip, c7, c7, 0 @ invalidate I & D caches, BTB
mcr p15, 0, ip, c7, c10, 4 @ drain write (&fill) buffer
diff --git a/arch/arm/plat-mxc/devices/Kconfig b/arch/arm/plat-mxc/devices/Kconfig
index b0f74f7..cb3e3ee 100644
--- a/arch/arm/plat-mxc/devices/Kconfig
+++ b/arch/arm/plat-mxc/devices/Kconfig
@@ -79,3 +79,7 @@
config IMX_HAVE_PLATFORM_SPI_IMX
bool
+
+config IMX_HAVE_PLATFORM_AHCI
+ bool
+ default y if ARCH_MX53
diff --git a/arch/arm/plat-mxc/devices/Makefile b/arch/arm/plat-mxc/devices/Makefile
index a093b45..c11ac84 100644
--- a/arch/arm/plat-mxc/devices/Makefile
+++ b/arch/arm/plat-mxc/devices/Makefile
@@ -26,3 +26,4 @@
obj-$(CONFIG_IMX_HAVE_PLATFORM_MXC_W1) += platform-mxc_w1.o
obj-$(CONFIG_IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX) += platform-sdhci-esdhc-imx.o
obj-$(CONFIG_IMX_HAVE_PLATFORM_SPI_IMX) += platform-spi_imx.o
+obj-$(CONFIG_IMX_HAVE_PLATFORM_AHCI) += platform-ahci-imx.o
diff --git a/arch/arm/plat-mxc/devices/platform-ahci-imx.c b/arch/arm/plat-mxc/devices/platform-ahci-imx.c
new file mode 100644
index 0000000..d8a56ae
--- /dev/null
+++ b/arch/arm/plat-mxc/devices/platform-ahci-imx.c
@@ -0,0 +1,156 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc. All Rights Reserved.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <asm/sizes.h>
+#include <mach/hardware.h>
+#include <mach/devices-common.h>
+
+#define imx_ahci_imx_data_entry_single(soc, _devid) \
+ { \
+ .devid = _devid, \
+ .iobase = soc ## _SATA_BASE_ADDR, \
+ .irq = soc ## _INT_SATA, \
+ }
+
+#ifdef CONFIG_SOC_IMX53
+const struct imx_ahci_imx_data imx53_ahci_imx_data __initconst =
+ imx_ahci_imx_data_entry_single(MX53, "imx53-ahci");
+#endif
+
+enum {
+ HOST_CAP = 0x00,
+ HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
+ HOST_PORTS_IMPL = 0x0c,
+ HOST_TIMER1MS = 0xe0, /* Timer 1-ms */
+};
+
+static struct clk *sata_clk, *sata_ref_clk;
+
+/* AHCI module Initialization, if return 0, initialization is successful. */
+static int imx_sata_init(struct device *dev, void __iomem *addr)
+{
+ u32 tmpdata;
+ int ret = 0;
+ struct clk *clk;
+
+ sata_clk = clk_get(dev, "ahci");
+ if (IS_ERR(sata_clk)) {
+ dev_err(dev, "no sata clock.\n");
+ return PTR_ERR(sata_clk);
+ }
+ ret = clk_enable(sata_clk);
+ if (ret) {
+ dev_err(dev, "can't enable sata clock.\n");
+ goto put_sata_clk;
+ }
+
+ /* Get the AHCI SATA PHY CLK */
+ sata_ref_clk = clk_get(dev, "ahci_phy");
+ if (IS_ERR(sata_ref_clk)) {
+ dev_err(dev, "no sata ref clock.\n");
+ ret = PTR_ERR(sata_ref_clk);
+ goto release_sata_clk;
+ }
+ ret = clk_enable(sata_ref_clk);
+ if (ret) {
+ dev_err(dev, "can't enable sata ref clock.\n");
+ goto put_sata_ref_clk;
+ }
+
+ /* Get the AHB clock rate, and configure the TIMER1MS reg later */
+ clk = clk_get(dev, "ahci_dma");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "no dma clock.\n");
+ ret = PTR_ERR(clk);
+ goto release_sata_ref_clk;
+ }
+ tmpdata = clk_get_rate(clk) / 1000;
+ clk_put(clk);
+
+ writel(tmpdata, addr + HOST_TIMER1MS);
+
+ tmpdata = readl(addr + HOST_CAP);
+ if (!(tmpdata & HOST_CAP_SSS)) {
+ tmpdata |= HOST_CAP_SSS;
+ writel(tmpdata, addr + HOST_CAP);
+ }
+
+ if (!(readl(addr + HOST_PORTS_IMPL) & 0x1))
+ writel((readl(addr + HOST_PORTS_IMPL) | 0x1),
+ addr + HOST_PORTS_IMPL);
+
+ return 0;
+
+release_sata_ref_clk:
+ clk_disable(sata_ref_clk);
+put_sata_ref_clk:
+ clk_put(sata_ref_clk);
+release_sata_clk:
+ clk_disable(sata_clk);
+put_sata_clk:
+ clk_put(sata_clk);
+
+ return ret;
+}
+
+static void imx_sata_exit(struct device *dev)
+{
+ clk_disable(sata_ref_clk);
+ clk_put(sata_ref_clk);
+
+ clk_disable(sata_clk);
+ clk_put(sata_clk);
+
+}
+struct platform_device *__init imx_add_ahci_imx(
+ const struct imx_ahci_imx_data *data,
+ const struct ahci_platform_data *pdata)
+{
+ struct resource res[] = {
+ {
+ .start = data->iobase,
+ .end = data->iobase + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = data->irq,
+ .end = data->irq,
+ .flags = IORESOURCE_IRQ,
+ },
+ };
+
+ return imx_add_platform_device_dmamask(data->devid, 0,
+ res, ARRAY_SIZE(res),
+ pdata, sizeof(*pdata), DMA_BIT_MASK(32));
+}
+
+struct platform_device *__init imx53_add_ahci_imx(void)
+{
+ struct ahci_platform_data pdata = {
+ .init = imx_sata_init,
+ .exit = imx_sata_exit,
+ };
+
+ return imx_add_ahci_imx(&imx53_ahci_imx_data, &pdata);
+}
diff --git a/arch/arm/plat-mxc/include/mach/devices-common.h b/arch/arm/plat-mxc/include/mach/devices-common.h
index 4cbad45..117a381 100644
--- a/arch/arm/plat-mxc/include/mach/devices-common.h
+++ b/arch/arm/plat-mxc/include/mach/devices-common.h
@@ -309,3 +309,13 @@
struct platform_device *imx_add_imx_dma(void);
struct platform_device *imx_add_imx_sdma(char *name,
resource_size_t iobase, int irq, struct sdma_platform_data *pdata);
+
+#include <linux/ahci_platform.h>
+struct imx_ahci_imx_data {
+ const char *devid;
+ resource_size_t iobase;
+ resource_size_t irq;
+};
+struct platform_device *__init imx_add_ahci_imx(
+ const struct imx_ahci_imx_data *data,
+ const struct ahci_platform_data *pdata);
diff --git a/arch/arm/plat-omap/omap_device.c b/arch/arm/plat-omap/omap_device.c
index b6b4097..02609ee 100644
--- a/arch/arm/plat-omap/omap_device.c
+++ b/arch/arm/plat-omap/omap_device.c
@@ -615,6 +615,9 @@
return pm_generic_resume_noirq(dev);
}
+#else
+#define _od_suspend_noirq NULL
+#define _od_resume_noirq NULL
#endif
static struct dev_pm_domain omap_device_pm_domain = {
@@ -622,7 +625,8 @@
SET_RUNTIME_PM_OPS(_od_runtime_suspend, _od_runtime_resume,
_od_runtime_idle)
USE_PLATFORM_PM_SLEEP_OPS
- SET_SYSTEM_SLEEP_PM_OPS(_od_suspend_noirq, _od_resume_noirq)
+ .suspend_noirq = _od_suspend_noirq,
+ .resume_noirq = _od_resume_noirq,
}
};
diff --git a/arch/arm/plat-s5p/clock.c b/arch/arm/plat-s5p/clock.c
index 02af235..5f84a3f 100644
--- a/arch/arm/plat-s5p/clock.c
+++ b/arch/arm/plat-s5p/clock.c
@@ -192,7 +192,7 @@
if (IS_ERR(pclk))
return -EINVAL;
- rate = pclk->ops->get_rate(clk);
+ rate = pclk->ops->get_rate(pclk);
clk_put(pclk);
return rate;
diff --git a/arch/arm/plat-s5p/irq-gpioint.c b/arch/arm/plat-s5p/irq-gpioint.c
index 327ab9f..f88216d 100644
--- a/arch/arm/plat-s5p/irq-gpioint.c
+++ b/arch/arm/plat-s5p/irq-gpioint.c
@@ -23,6 +23,8 @@
#include <plat/gpio-core.h>
#include <plat/gpio-cfg.h>
+#include <asm/mach/irq.h>
+
#define GPIO_BASE(chip) (((unsigned long)(chip)->base) & 0xFFFFF000u)
#define CON_OFFSET 0x700
@@ -81,6 +83,9 @@
int group, pend_offset, mask_offset;
unsigned int pend, mask;
+ struct irq_chip *chip = irq_get_chip(irq);
+ chained_irq_enter(chip, desc);
+
for (group = 0; group < bank->nr_groups; group++) {
struct s3c_gpio_chip *chip = bank->chips[group];
if (!chip)
@@ -102,23 +107,25 @@
pend &= ~BIT(offset);
}
}
+ chained_irq_exit(chip, desc);
}
static __init int s5p_gpioint_add(struct s3c_gpio_chip *chip)
{
static int used_gpioint_groups = 0;
int group = chip->group;
- struct s5p_gpioint_bank *bank = NULL;
+ struct s5p_gpioint_bank *b, *bank = NULL;
struct irq_chip_generic *gc;
struct irq_chip_type *ct;
if (used_gpioint_groups >= S5P_GPIOINT_GROUP_COUNT)
return -ENOMEM;
- list_for_each_entry(bank, &banks, list) {
- if (group >= bank->start &&
- group < bank->start + bank->nr_groups)
+ list_for_each_entry(b, &banks, list) {
+ if (group >= b->start && group < b->start + b->nr_groups) {
+ bank = b;
break;
+ }
}
if (!bank)
return -EINVAL;
diff --git a/arch/arm/plat-samsung/clock.c b/arch/arm/plat-samsung/clock.c
index 302c426..3b44519 100644
--- a/arch/arm/plat-samsung/clock.c
+++ b/arch/arm/plat-samsung/clock.c
@@ -64,6 +64,17 @@
*/
DEFINE_SPINLOCK(clocks_lock);
+/* Global watchdog clock used by arch_wtd_reset() callback */
+struct clk *s3c2410_wdtclk;
+static int __init s3c_wdt_reset_init(void)
+{
+ s3c2410_wdtclk = clk_get(NULL, "watchdog");
+ if (IS_ERR(s3c2410_wdtclk))
+ printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__);
+ return 0;
+}
+arch_initcall(s3c_wdt_reset_init);
+
/* enable and disable calls for use with the clk struct */
static int clk_null_enable(struct clk *clk, int enable)
diff --git a/arch/arm/plat-samsung/include/plat/backlight.h b/arch/arm/plat-samsung/include/plat/backlight.h
index 51d8da8..ad530c7 100644
--- a/arch/arm/plat-samsung/include/plat/backlight.h
+++ b/arch/arm/plat-samsung/include/plat/backlight.h
@@ -20,7 +20,7 @@
int func;
};
-extern void samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
+extern void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
struct platform_pwm_backlight_data *bl_data);
#endif /* __ASM_PLAT_BACKLIGHT_H */
diff --git a/arch/arm/plat-samsung/include/plat/clock.h b/arch/arm/plat-samsung/include/plat/clock.h
index 87d5b38..73c66d4 100644
--- a/arch/arm/plat-samsung/include/plat/clock.h
+++ b/arch/arm/plat-samsung/include/plat/clock.h
@@ -9,6 +9,9 @@
* published by the Free Software Foundation.
*/
+#ifndef __ASM_PLAT_CLOCK_H
+#define __ASM_PLAT_CLOCK_H __FILE__
+
#include <linux/spinlock.h>
#include <linux/clkdev.h>
@@ -121,3 +124,8 @@
extern void s3c_pwmclk_init(void);
+/* Global watchdog clock used by arch_wtd_reset() callback */
+
+extern struct clk *s3c2410_wdtclk;
+
+#endif /* __ASM_PLAT_CLOCK_H */
diff --git a/arch/arm/plat-samsung/include/plat/watchdog-reset.h b/arch/arm/plat-samsung/include/plat/watchdog-reset.h
index 54b762a..40dbb2b 100644
--- a/arch/arm/plat-samsung/include/plat/watchdog-reset.h
+++ b/arch/arm/plat-samsung/include/plat/watchdog-reset.h
@@ -10,6 +10,7 @@
* published by the Free Software Foundation.
*/
+#include <plat/clock.h>
#include <plat/regs-watchdog.h>
#include <mach/map.h>
@@ -19,17 +20,12 @@
static inline void arch_wdt_reset(void)
{
- struct clk *wdtclk;
-
printk("arch_reset: attempting watchdog reset\n");
__raw_writel(0, S3C2410_WTCON); /* disable watchdog, to be safe */
- wdtclk = clk_get(NULL, "watchdog");
- if (!IS_ERR(wdtclk)) {
- clk_enable(wdtclk);
- } else
- printk(KERN_WARNING "%s: warning: cannot get watchdog clock\n", __func__);
+ if (s3c2410_wdtclk)
+ clk_enable(s3c2410_wdtclk);
/* put initial values into count and data */
__raw_writel(0x80, S3C2410_WTCNT);
diff --git a/arch/arm/plat-samsung/irq-vic-timer.c b/arch/arm/plat-samsung/irq-vic-timer.c
index f714d06..51583cd 100644
--- a/arch/arm/plat-samsung/irq-vic-timer.c
+++ b/arch/arm/plat-samsung/irq-vic-timer.c
@@ -22,9 +22,14 @@
#include <plat/irq-vic-timer.h>
#include <plat/regs-timer.h>
+#include <asm/mach/irq.h>
+
static void s3c_irq_demux_vic_timer(unsigned int irq, struct irq_desc *desc)
{
+ struct irq_chip *chip = irq_get_chip(irq);
+ chained_irq_enter(chip, desc);
generic_handle_irq((int)desc->irq_data.handler_data);
+ chained_irq_exit(chip, desc);
}
/* We assume the IRQ_TIMER0..IRQ_TIMER4 range is continuous. */
diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types
index fff68d0..62cc8f9 100644
--- a/arch/arm/tools/mach-types
+++ b/arch/arm/tools/mach-types
@@ -351,7 +351,7 @@
nokia_rx51 MACH_NOKIA_RX51 NOKIA_RX51 1955
omap_zoom2 MACH_OMAP_ZOOM2 OMAP_ZOOM2 1967
cpuat9260 MACH_CPUAT9260 CPUAT9260 1973
-eukrea_cpuimx27 MACH_CPUIMX27 CPUIMX27 1975
+eukrea_cpuimx27 MACH_EUKREA_CPUIMX27 EUKREA_CPUIMX27 1975
acs5k MACH_ACS5K ACS5K 1982
snapper_9260 MACH_SNAPPER_9260 SNAPPER_9260 1987
dsm320 MACH_DSM320 DSM320 1988
@@ -476,8 +476,8 @@
omap4_panda MACH_OMAP4_PANDA OMAP4_PANDA 2791
ti8168evm MACH_TI8168EVM TI8168EVM 2800
teton_bga MACH_TETON_BGA TETON_BGA 2816
-eukrea_cpuimx25sd MACH_EUKREA_CPUIMX25 EUKREA_CPUIMX25 2820
-eukrea_cpuimx35sd MACH_EUKREA_CPUIMX35 EUKREA_CPUIMX35 2821
+eukrea_cpuimx25sd MACH_EUKREA_CPUIMX25SD EUKREA_CPUIMX25SD 2820
+eukrea_cpuimx35sd MACH_EUKREA_CPUIMX35SD EUKREA_CPUIMX35SD 2821
eukrea_cpuimx51sd MACH_EUKREA_CPUIMX51SD EUKREA_CPUIMX51SD 2822
eukrea_cpuimx51 MACH_EUKREA_CPUIMX51 EUKREA_CPUIMX51 2823
smdkc210 MACH_SMDKC210 SMDKC210 2838