ide: move CONFIG_IDE_ETRAX to drivers/ide/Kconfig
* Move ETRAX_IDE and friends from arch/cris/arch-{v10,v32}/drivers/Kconfig
to drivers/ide/Kconfig.
* Don't force selecting ide-disk and ide-cd device drivers
(please handle this through defconfig if necessary).
* Make ETRAX_IDE depend on BROKEN for the time being
(it doesn't even compile currently).
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index faf8b4d..e3c0f29 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -542,45 +542,6 @@
loopback. Not all products are able to do this in software only.
Axis 2400/2401 must disable receiver.
-config ETRAX_IDE
- bool "ATA/IDE support"
- select IDE
- select BLK_DEV_IDE
- select BLK_DEV_IDEDISK
- select BLK_DEV_IDECD
- select BLK_DEV_IDEDMA
- select IDE_GENERIC
- help
- Enable this to get support for ATA/IDE.
- You can't use parallel ports or SCSI ports
- at the same time.
-
-
-config ETRAX_IDE_DELAY
- int "Delay for drives to regain consciousness"
- depends on ETRAX_IDE
- default 15
- help
- Number of seconds to wait for IDE drives to spin up after an IDE
- reset.
-choice
- prompt "IDE reset pin"
- depends on ETRAX_IDE
- default ETRAX_IDE_PB7_RESET
-
-config ETRAX_IDE_PB7_RESET
- bool "Port_PB_Bit_7"
- help
- IDE reset on pin 7 on port B
-
-config ETRAX_IDE_G27_RESET
- bool "Port_G_Bit_27"
- help
- IDE reset on pin 27 on port G
-
-endchoice
-
-
config ETRAX_USB_HOST
bool "USB host"
select USB
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
index 7f72d7c..9bccb5e 100644
--- a/arch/cris/arch-v32/drivers/Kconfig
+++ b/arch/cris/arch-v32/drivers/Kconfig
@@ -582,18 +582,6 @@
that a user can change the value on using ioctl's.
Bit set = changeable.
-config ETRAX_IDE
- bool "ATA/IDE support"
- depends on ETRAX_ARCH_V32
- select IDE
- select BLK_DEV_IDE
- select BLK_DEV_IDEDISK
- select BLK_DEV_IDECD
- select BLK_DEV_IDEDMA
- select IDE_GENERIC
- help
- Enables the ETRAX IDE driver.
-
config ETRAX_CARDBUS
bool "Cardbus support"
depends on ETRAX_ARCH_V32
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index ca8239a..403e3ff 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -882,6 +882,41 @@
Say Y here if you want to support the onboard IDE channels on the
Simtec BAST or the Thorcom VR1000
+config ETRAX_IDE
+ bool "ETRAX IDE support"
+ depends on CRIS && BROKEN
+ select BLK_DEV_IDEDMA
+ select IDE_GENERIC
+ help
+ Enables the ETRAX IDE driver.
+
+ You can't use parallel ports or SCSI ports at the same time.
+
+config ETRAX_IDE_DELAY
+ int "Delay for drives to regain consciousness"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default 15
+ help
+ Number of seconds to wait for IDE drives to spin up after an IDE
+ reset.
+
+choice
+ prompt "IDE reset pin"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default ETRAX_IDE_PB7_RESET
+
+config ETRAX_IDE_PB7_RESET
+ bool "Port_PB_Bit_7"
+ help
+ IDE reset on pin 7 on port B
+
+config ETRAX_IDE_G27_RESET
+ bool "Port_G_Bit_27"
+ help
+ IDE reset on pin 27 on port G
+
+endchoice
+
config IDE_H8300
bool "H8300 IDE support"
depends on H8300