| Device tree bindings for GPMC connected NANDs | 
 |  | 
 | GPMC connected NAND (found on OMAP boards) are represented as child nodes of | 
 | the GPMC controller with a name of "nand". | 
 |  | 
 | All timing relevant properties as well as generic gpmc child properties are | 
 | explained in a separate documents - please refer to | 
 | Documentation/devicetree/bindings/bus/ti-gpmc.txt | 
 |  | 
 | For NAND specific properties such as ECC modes or bus width, please refer to | 
 | Documentation/devicetree/bindings/mtd/nand.txt | 
 |  | 
 |  | 
 | Required properties: | 
 |  | 
 |  - reg:		The CS line the peripheral is connected to | 
 |  | 
 | Optional properties: | 
 |  | 
 |  - nand-bus-width: 		Set this numeric value to 16 if the hardware | 
 | 				is wired that way. If not specified, a bus | 
 | 				width of 8 is assumed. | 
 |  | 
 |  - ti,nand-ecc-opt:		A string setting the ECC layout to use. One of: | 
 |  | 
 | 		"sw"		Software method (default) | 
 | 		"hw"		Hardware method | 
 | 		"hw-romcode"	gpmc hamming mode method & romcode layout | 
 | 		"bch4"		4-bit BCH ecc code | 
 | 		"bch8"		8-bit BCH ecc code | 
 |  | 
 |  - ti,nand-xfer-type:		A string setting the data transfer type. One of: | 
 |  | 
 | 		"prefetch-polled"	Prefetch polled mode (default) | 
 | 		"polled"		Polled mode, without prefetch | 
 | 		"prefetch-dma"		Prefetch enabled sDMA mode | 
 | 		"prefetch-irq"		Prefetch enabled irq mode | 
 |  | 
 |  - elm_id:	Specifies elm device node. This is required to support BCH | 
 |  		error correction using ELM module. | 
 |  | 
 | For inline partiton table parsing (optional): | 
 |  | 
 |  - #address-cells: should be set to 1 | 
 |  - #size-cells: should be set to 1 | 
 |  | 
 | Example for an AM33xx board: | 
 |  | 
 | 	gpmc: gpmc@50000000 { | 
 | 		compatible = "ti,am3352-gpmc"; | 
 | 		ti,hwmods = "gpmc"; | 
 | 		reg = <0x50000000 0x1000000>; | 
 | 		interrupts = <100>; | 
 | 		gpmc,num-cs = <8>; | 
 | 		gpmc,num-waitpins = <2>; | 
 | 		#address-cells = <2>; | 
 | 		#size-cells = <1>; | 
 | 		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */ | 
 | 		elm_id = <&elm>; | 
 |  | 
 | 		nand@0,0 { | 
 | 			reg = <0 0 0>; /* CS0, offset 0 */ | 
 | 			nand-bus-width = <16>; | 
 | 			ti,nand-ecc-opt = "bch8"; | 
 | 			ti,nand-xfer-type = "polled"; | 
 |  | 
 | 			gpmc,sync-clk-ps = <0>; | 
 | 			gpmc,cs-on-ns = <0>; | 
 | 			gpmc,cs-rd-off-ns = <44>; | 
 | 			gpmc,cs-wr-off-ns = <44>; | 
 | 			gpmc,adv-on-ns = <6>; | 
 | 			gpmc,adv-rd-off-ns = <34>; | 
 | 			gpmc,adv-wr-off-ns = <44>; | 
 | 			gpmc,we-off-ns = <40>; | 
 | 			gpmc,oe-off-ns = <54>; | 
 | 			gpmc,access-ns = <64>; | 
 | 			gpmc,rd-cycle-ns = <82>; | 
 | 			gpmc,wr-cycle-ns = <82>; | 
 | 			gpmc,wr-access-ns = <40>; | 
 | 			gpmc,wr-data-mux-bus-ns = <0>; | 
 |  | 
 | 			#address-cells = <1>; | 
 | 			#size-cells = <1>; | 
 |  | 
 | 			/* partitions go here */ | 
 | 		}; | 
 | 	}; | 
 |  |