Serial: Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs
Add support for new devices: Exar's XR17V35x family of multi-port PCIe UARTs.
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/tty/serial/8250/8250.c b/drivers/tty/serial/8250/8250.c
index 2af83a2..3624df6 100644
--- a/drivers/tty/serial/8250/8250.c
+++ b/drivers/tty/serial/8250/8250.c
@@ -282,6 +282,15 @@
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR,
},
+ [PORT_XR17V35X] = {
+ .name = "XR17V35X",
+ .fifo_size = 256,
+ .tx_loadsz = 256,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
+ UART_FCR_T_TRIG_11,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP,
+ },
[PORT_LPC3220] = {
.name = "LPC3220",
.fifo_size = 64,
@@ -455,6 +464,7 @@
}
static int serial8250_default_handle_irq(struct uart_port *port);
+static int exar_handle_irq(struct uart_port *port);
static void set_io_from_upio(struct uart_port *p)
{
@@ -574,6 +584,18 @@
*/
static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
{
+ /*
+ * Exar UARTs have a SLEEP register that enables or disables
+ * each UART to enter sleep mode separately. On the XR17V35x the
+ * register is accessible to each UART at the UART_EXAR_SLEEP
+ * offset but the UART channel may only write to the corresponding
+ * bit.
+ */
+ if (p->port.type == PORT_XR17V35X) {
+ serial_out(p, UART_EXAR_SLEEP, 0xff);
+ return;
+ }
+
if (p->capabilities & UART_CAP_SLEEP) {
if (p->capabilities & UART_CAP_EFR) {
serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
@@ -882,6 +904,27 @@
up->capabilities |= UART_CAP_FIFO;
/*
+ * XR17V35x UARTs have an extra divisor register, DLD
+ * that gets enabled with when DLAB is set which will
+ * cause the device to incorrectly match and assign
+ * port type to PORT_16650. The EFR for this UART is
+ * found at offset 0x09. Instead check the Deice ID (DVID)
+ * register for a 2, 4 or 8 port UART.
+ */
+ status1 = serial_in(up, UART_EXAR_DVID);
+ if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
+ if (up->port.flags & UPF_EXAR_EFR) {
+ DEBUG_AUTOCONF("Exar XR17V35x ");
+ up->port.type = PORT_XR17V35X;
+ up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP;
+
+ return;
+ }
+
+ }
+
+ /*
* Check for presence of the EFR when DLAB is set.
* Only ST16C650V1 UARTs pass this test.
*/
@@ -1516,6 +1559,30 @@
}
/*
+ * These Exar UARTs have an extra interrupt indicator that could
+ * fire for a few unimplemented interrupts. One of which is a
+ * wakeup event when coming out of sleep. Put this here just
+ * to be on the safe side that these interrupts don't go unhandled.
+ */
+static int exar_handle_irq(struct uart_port *port)
+{
+ unsigned char int0, int1, int2, int3;
+ unsigned int iir = serial_port_in(port, UART_IIR);
+ int ret;
+
+ ret = serial8250_handle_irq(port, iir);
+
+ if (port->type == PORT_XR17V35X) {
+ int0 = serial_port_in(port, 0x80);
+ int1 = serial_port_in(port, 0x81);
+ int2 = serial_port_in(port, 0x82);
+ int3 = serial_port_in(port, 0x83);
+ }
+
+ return ret;
+}
+
+/*
* This is the serial driver's interrupt routine.
*
* Arjan thinks the old way was overly complex, so it got simplified.
@@ -2614,6 +2681,10 @@
serial8250_release_rsa_resource(up);
if (port->type == PORT_UNKNOWN)
serial8250_release_std_resource(up);
+
+ /* Fixme: probably not the best place for this */
+ if (port->type == PORT_XR17V35X)
+ port->handle_irq = exar_handle_irq;
}
static int