[SCSI] mvsas: split driver into multiple files
Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
diff --git a/drivers/scsi/mvsas/mv_defs.h b/drivers/scsi/mvsas/mv_defs.h
new file mode 100644
index 0000000..d8e96a3
--- /dev/null
+++ b/drivers/scsi/mvsas/mv_defs.h
@@ -0,0 +1,441 @@
+/*
+ mv_defs.h - Marvell 88SE6440 SAS/SATA support
+
+ Copyright 2007 Red Hat, Inc.
+ Copyright 2008 Marvell. <kewei@marvell.com>
+
+ This program is free software; you can redistribute it and/or
+ modify it under the terms of the GNU General Public License as
+ published by the Free Software Foundation; either version 2,
+ or (at your option) any later version.
+
+ This program is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty
+ of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ See the GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public
+ License along with this program; see the file COPYING. If not,
+ write to the Free Software Foundation, 675 Mass Ave, Cambridge,
+ MA 02139, USA.
+
+ */
+
+#ifndef _MV_DEFS_H_
+#define _MV_DEFS_H_
+
+/* driver compile-time configuration */
+enum driver_configuration {
+ MVS_TX_RING_SZ = 1024, /* TX ring size (12-bit) */
+ MVS_RX_RING_SZ = 1024, /* RX ring size (12-bit) */
+ /* software requires power-of-2
+ ring size */
+
+ MVS_SLOTS = 512, /* command slots */
+ MVS_SLOT_BUF_SZ = 8192, /* cmd tbl + IU + status + PRD */
+ MVS_SSP_CMD_SZ = 64, /* SSP command table buffer size */
+ MVS_ATA_CMD_SZ = 96, /* SATA command table buffer size */
+ MVS_OAF_SZ = 64, /* Open address frame buffer size */
+
+ MVS_RX_FIS_COUNT = 17, /* Optional rx'd FISs (max 17) */
+
+ MVS_QUEUE_SIZE = 30, /* Support Queue depth */
+ MVS_CAN_QUEUE = MVS_SLOTS - 1, /* SCSI Queue depth */
+};
+
+/* unchangeable hardware details */
+enum hardware_details {
+ MVS_MAX_PHYS = 8, /* max. possible phys */
+ MVS_MAX_PORTS = 8, /* max. possible ports */
+ MVS_RX_FISL_SZ = 0x400 + (MVS_RX_FIS_COUNT * 0x100),
+};
+
+/* peripheral registers (BAR2) */
+enum peripheral_registers {
+ SPI_CTL = 0x10, /* EEPROM control */
+ SPI_CMD = 0x14, /* EEPROM command */
+ SPI_DATA = 0x18, /* EEPROM data */
+};
+
+enum peripheral_register_bits {
+ TWSI_RDY = (1U << 7), /* EEPROM interface ready */
+ TWSI_RD = (1U << 4), /* EEPROM read access */
+
+ SPI_ADDR_MASK = 0x3ffff, /* bits 17:0 */
+};
+
+enum hw_register_bits {
+ /* MVS_GBL_CTL */
+ INT_EN = (1U << 1), /* Global int enable */
+ HBA_RST = (1U << 0), /* HBA reset */
+
+ /* MVS_GBL_INT_STAT */
+ INT_XOR = (1U << 4), /* XOR engine event */
+ INT_SAS_SATA = (1U << 0), /* SAS/SATA event */
+
+ /* MVS_GBL_PORT_TYPE */ /* shl for ports 1-3 */
+ SATA_TARGET = (1U << 16), /* port0 SATA target enable */
+ MODE_AUTO_DET_PORT7 = (1U << 15), /* port0 SAS/SATA autodetect */
+ MODE_AUTO_DET_PORT6 = (1U << 14),
+ MODE_AUTO_DET_PORT5 = (1U << 13),
+ MODE_AUTO_DET_PORT4 = (1U << 12),
+ MODE_AUTO_DET_PORT3 = (1U << 11),
+ MODE_AUTO_DET_PORT2 = (1U << 10),
+ MODE_AUTO_DET_PORT1 = (1U << 9),
+ MODE_AUTO_DET_PORT0 = (1U << 8),
+ MODE_AUTO_DET_EN = MODE_AUTO_DET_PORT0 | MODE_AUTO_DET_PORT1 |
+ MODE_AUTO_DET_PORT2 | MODE_AUTO_DET_PORT3 |
+ MODE_AUTO_DET_PORT4 | MODE_AUTO_DET_PORT5 |
+ MODE_AUTO_DET_PORT6 | MODE_AUTO_DET_PORT7,
+ MODE_SAS_PORT7_MASK = (1U << 7), /* port0 SAS(1), SATA(0) mode */
+ MODE_SAS_PORT6_MASK = (1U << 6),
+ MODE_SAS_PORT5_MASK = (1U << 5),
+ MODE_SAS_PORT4_MASK = (1U << 4),
+ MODE_SAS_PORT3_MASK = (1U << 3),
+ MODE_SAS_PORT2_MASK = (1U << 2),
+ MODE_SAS_PORT1_MASK = (1U << 1),
+ MODE_SAS_PORT0_MASK = (1U << 0),
+ MODE_SAS_SATA = MODE_SAS_PORT0_MASK | MODE_SAS_PORT1_MASK |
+ MODE_SAS_PORT2_MASK | MODE_SAS_PORT3_MASK |
+ MODE_SAS_PORT4_MASK | MODE_SAS_PORT5_MASK |
+ MODE_SAS_PORT6_MASK | MODE_SAS_PORT7_MASK,
+
+ /* SAS_MODE value may be
+ * dictated (in hw) by values
+ * of SATA_TARGET & AUTO_DET
+ */
+
+ /* MVS_TX_CFG */
+ TX_EN = (1U << 16), /* Enable TX */
+ TX_RING_SZ_MASK = 0xfff, /* TX ring size, bits 11:0 */
+
+ /* MVS_RX_CFG */
+ RX_EN = (1U << 16), /* Enable RX */
+ RX_RING_SZ_MASK = 0xfff, /* RX ring size, bits 11:0 */
+
+ /* MVS_INT_COAL */
+ COAL_EN = (1U << 16), /* Enable int coalescing */
+
+ /* MVS_INT_STAT, MVS_INT_MASK */
+ CINT_I2C = (1U << 31), /* I2C event */
+ CINT_SW0 = (1U << 30), /* software event 0 */
+ CINT_SW1 = (1U << 29), /* software event 1 */
+ CINT_PRD_BC = (1U << 28), /* PRD BC err for read cmd */
+ CINT_DMA_PCIE = (1U << 27), /* DMA to PCIE timeout */
+ CINT_MEM = (1U << 26), /* int mem parity err */
+ CINT_I2C_SLAVE = (1U << 25), /* slave I2C event */
+ CINT_SRS = (1U << 3), /* SRS event */
+ CINT_CI_STOP = (1U << 1), /* cmd issue stopped */
+ CINT_DONE = (1U << 0), /* cmd completion */
+
+ /* shl for ports 1-3 */
+ CINT_PORT_STOPPED = (1U << 16), /* port0 stopped */
+ CINT_PORT = (1U << 8), /* port0 event */
+ CINT_PORT_MASK_OFFSET = 8,
+ CINT_PORT_MASK = (0xFF << CINT_PORT_MASK_OFFSET),
+
+ /* TX (delivery) ring bits */
+ TXQ_CMD_SHIFT = 29,
+ TXQ_CMD_SSP = 1, /* SSP protocol */
+ TXQ_CMD_SMP = 2, /* SMP protocol */
+ TXQ_CMD_STP = 3, /* STP/SATA protocol */
+ TXQ_CMD_SSP_FREE_LIST = 4, /* add to SSP targ free list */
+ TXQ_CMD_SLOT_RESET = 7, /* reset command slot */
+ TXQ_MODE_I = (1U << 28), /* mode: 0=target,1=initiator */
+ TXQ_PRIO_HI = (1U << 27), /* priority: 0=normal, 1=high */
+ TXQ_SRS_SHIFT = 20, /* SATA register set */
+ TXQ_SRS_MASK = 0x7f,
+ TXQ_PHY_SHIFT = 12, /* PHY bitmap */
+ TXQ_PHY_MASK = 0xff,
+ TXQ_SLOT_MASK = 0xfff, /* slot number */
+
+ /* RX (completion) ring bits */
+ RXQ_GOOD = (1U << 23), /* Response good */
+ RXQ_SLOT_RESET = (1U << 21), /* Slot reset complete */
+ RXQ_CMD_RX = (1U << 20), /* target cmd received */
+ RXQ_ATTN = (1U << 19), /* attention */
+ RXQ_RSP = (1U << 18), /* response frame xfer'd */
+ RXQ_ERR = (1U << 17), /* err info rec xfer'd */
+ RXQ_DONE = (1U << 16), /* cmd complete */
+ RXQ_SLOT_MASK = 0xfff, /* slot number */
+
+ /* mvs_cmd_hdr bits */
+ MCH_PRD_LEN_SHIFT = 16, /* 16-bit PRD table len */
+ MCH_SSP_FR_TYPE_SHIFT = 13, /* SSP frame type */
+
+ /* SSP initiator only */
+ MCH_SSP_FR_CMD = 0x0, /* COMMAND frame */
+
+ /* SSP initiator or target */
+ MCH_SSP_FR_TASK = 0x1, /* TASK frame */
+
+ /* SSP target only */
+ MCH_SSP_FR_XFER_RDY = 0x4, /* XFER_RDY frame */
+ MCH_SSP_FR_RESP = 0x5, /* RESPONSE frame */
+ MCH_SSP_FR_READ = 0x6, /* Read DATA frame(s) */
+ MCH_SSP_FR_READ_RESP = 0x7, /* ditto, plus RESPONSE */
+
+ MCH_PASSTHRU = (1U << 12), /* pass-through (SSP) */
+ MCH_FBURST = (1U << 11), /* first burst (SSP) */
+ MCH_CHK_LEN = (1U << 10), /* chk xfer len (SSP) */
+ MCH_RETRY = (1U << 9), /* tport layer retry (SSP) */
+ MCH_PROTECTION = (1U << 8), /* protection info rec (SSP) */
+ MCH_RESET = (1U << 7), /* Reset (STP/SATA) */
+ MCH_FPDMA = (1U << 6), /* First party DMA (STP/SATA) */
+ MCH_ATAPI = (1U << 5), /* ATAPI (STP/SATA) */
+ MCH_BIST = (1U << 4), /* BIST activate (STP/SATA) */
+ MCH_PMP_MASK = 0xf, /* PMP from cmd FIS (STP/SATA)*/
+
+ CCTL_RST = (1U << 5), /* port logic reset */
+
+ /* 0(LSB first), 1(MSB first) */
+ CCTL_ENDIAN_DATA = (1U << 3), /* PRD data */
+ CCTL_ENDIAN_RSP = (1U << 2), /* response frame */
+ CCTL_ENDIAN_OPEN = (1U << 1), /* open address frame */
+ CCTL_ENDIAN_CMD = (1U << 0), /* command table */
+
+ /* MVS_Px_SER_CTLSTAT (per-phy control) */
+ PHY_SSP_RST = (1U << 3), /* reset SSP link layer */
+ PHY_BCAST_CHG = (1U << 2), /* broadcast(change) notif */
+ PHY_RST_HARD = (1U << 1), /* hard reset + phy reset */
+ PHY_RST = (1U << 0), /* phy reset */
+ PHY_MIN_SPP_PHYS_LINK_RATE_MASK = (0xF << 8),
+ PHY_MAX_SPP_PHYS_LINK_RATE_MASK = (0xF << 12),
+ PHY_NEG_SPP_PHYS_LINK_RATE_MASK_OFFSET = (16),
+ PHY_NEG_SPP_PHYS_LINK_RATE_MASK =
+ (0xF << PHY_NEG_SPP_PHYS_LINK_RATE_MASK_OFFSET),
+ PHY_READY_MASK = (1U << 20),
+
+ /* MVS_Px_INT_STAT, MVS_Px_INT_MASK (per-phy events) */
+ PHYEV_DEC_ERR = (1U << 24), /* Phy Decoding Error */
+ PHYEV_UNASSOC_FIS = (1U << 19), /* unassociated FIS rx'd */
+ PHYEV_AN = (1U << 18), /* SATA async notification */
+ PHYEV_BIST_ACT = (1U << 17), /* BIST activate FIS */
+ PHYEV_SIG_FIS = (1U << 16), /* signature FIS */
+ PHYEV_POOF = (1U << 12), /* phy ready from 1 -> 0 */
+ PHYEV_IU_BIG = (1U << 11), /* IU too long err */
+ PHYEV_IU_SMALL = (1U << 10), /* IU too short err */
+ PHYEV_UNK_TAG = (1U << 9), /* unknown tag */
+ PHYEV_BROAD_CH = (1U << 8), /* broadcast(CHANGE) */
+ PHYEV_COMWAKE = (1U << 7), /* COMWAKE rx'd */
+ PHYEV_PORT_SEL = (1U << 6), /* port selector present */
+ PHYEV_HARD_RST = (1U << 5), /* hard reset rx'd */
+ PHYEV_ID_TMOUT = (1U << 4), /* identify timeout */
+ PHYEV_ID_FAIL = (1U << 3), /* identify failed */
+ PHYEV_ID_DONE = (1U << 2), /* identify done */
+ PHYEV_HARD_RST_DONE = (1U << 1), /* hard reset done */
+ PHYEV_RDY_CH = (1U << 0), /* phy ready changed state */
+
+ /* MVS_PCS */
+ PCS_EN_SATA_REG_SHIFT = (16), /* Enable SATA Register Set */
+ PCS_EN_PORT_XMT_SHIFT = (12), /* Enable Port Transmit */
+ PCS_EN_PORT_XMT_SHIFT2 = (8), /* For 6480 */
+ PCS_SATA_RETRY = (1U << 8), /* retry ctl FIS on R_ERR */
+ PCS_RSP_RX_EN = (1U << 7), /* raw response rx */
+ PCS_SELF_CLEAR = (1U << 5), /* self-clearing int mode */
+ PCS_FIS_RX_EN = (1U << 4), /* FIS rx enable */
+ PCS_CMD_STOP_ERR = (1U << 3), /* cmd stop-on-err enable */
+ PCS_CMD_RST = (1U << 1), /* reset cmd issue */
+ PCS_CMD_EN = (1U << 0), /* enable cmd issue */
+
+ /* Port n Attached Device Info */
+ PORT_DEV_SSP_TRGT = (1U << 19),
+ PORT_DEV_SMP_TRGT = (1U << 18),
+ PORT_DEV_STP_TRGT = (1U << 17),
+ PORT_DEV_SSP_INIT = (1U << 11),
+ PORT_DEV_SMP_INIT = (1U << 10),
+ PORT_DEV_STP_INIT = (1U << 9),
+ PORT_PHY_ID_MASK = (0xFFU << 24),
+ PORT_DEV_TRGT_MASK = (0x7U << 17),
+ PORT_DEV_INIT_MASK = (0x7U << 9),
+ PORT_DEV_TYPE_MASK = (0x7U << 0),
+
+ /* Port n PHY Status */
+ PHY_RDY = (1U << 2),
+ PHY_DW_SYNC = (1U << 1),
+ PHY_OOB_DTCTD = (1U << 0),
+
+ /* VSR */
+ /* PHYMODE 6 (CDB) */
+ PHY_MODE6_LATECLK = (1U << 29), /* Lock Clock */
+ PHY_MODE6_DTL_SPEED = (1U << 27), /* Digital Loop Speed */
+ PHY_MODE6_FC_ORDER = (1U << 26), /* Fibre Channel Mode Order*/
+ PHY_MODE6_MUCNT_EN = (1U << 24), /* u Count Enable */
+ PHY_MODE6_SEL_MUCNT_LEN = (1U << 22), /* Training Length Select */
+ PHY_MODE6_SELMUPI = (1U << 20), /* Phase Multi Select (init) */
+ PHY_MODE6_SELMUPF = (1U << 18), /* Phase Multi Select (final) */
+ PHY_MODE6_SELMUFF = (1U << 16), /* Freq Loop Multi Sel(final) */
+ PHY_MODE6_SELMUFI = (1U << 14), /* Freq Loop Multi Sel(init) */
+ PHY_MODE6_FREEZE_LOOP = (1U << 12), /* Freeze Rx CDR Loop */
+ PHY_MODE6_INT_RXFOFFS = (1U << 3), /* Rx CDR Freq Loop Enable */
+ PHY_MODE6_FRC_RXFOFFS = (1U << 2), /* Initial Rx CDR Offset */
+ PHY_MODE6_STAU_0D8 = (1U << 1), /* Rx CDR Freq Loop Saturate */
+ PHY_MODE6_RXSAT_DIS = (1U << 0), /* Saturate Ctl */
+};
+
+/* SAS/SATA configuration port registers, aka phy registers */
+enum sas_sata_config_port_regs {
+ PHYR_IDENTIFY = 0x00, /* info for IDENTIFY frame */
+ PHYR_ADDR_LO = 0x04, /* my SAS address (low) */
+ PHYR_ADDR_HI = 0x08, /* my SAS address (high) */
+ PHYR_ATT_DEV_INFO = 0x0C, /* attached device info */
+ PHYR_ATT_ADDR_LO = 0x10, /* attached dev SAS addr (low) */
+ PHYR_ATT_ADDR_HI = 0x14, /* attached dev SAS addr (high) */
+ PHYR_SATA_CTL = 0x18, /* SATA control */
+ PHYR_PHY_STAT = 0x1C, /* PHY status */
+ PHYR_SATA_SIG0 = 0x20, /*port SATA signature FIS(Byte 0-3) */
+ PHYR_SATA_SIG1 = 0x24, /*port SATA signature FIS(Byte 4-7) */
+ PHYR_SATA_SIG2 = 0x28, /*port SATA signature FIS(Byte 8-11) */
+ PHYR_SATA_SIG3 = 0x2c, /*port SATA signature FIS(Byte 12-15) */
+ PHYR_R_ERR_COUNT = 0x30, /* port R_ERR count register */
+ PHYR_CRC_ERR_COUNT = 0x34, /* port CRC error count register */
+ PHYR_WIDE_PORT = 0x38, /* wide port participating */
+ PHYR_CURRENT0 = 0x80, /* current connection info 0 */
+ PHYR_CURRENT1 = 0x84, /* current connection info 1 */
+ PHYR_CURRENT2 = 0x88, /* current connection info 2 */
+};
+
+enum mvs_info_flags {
+ MVF_MSI = (1U << 0), /* MSI is enabled */
+ MVF_PHY_PWR_FIX = (1U << 1), /* bug workaround */
+};
+
+enum sas_cmd_port_registers {
+ CMD_CMRST_OOB_DET = 0x100, /* COMRESET OOB detect register */
+ CMD_CMWK_OOB_DET = 0x104, /* COMWAKE OOB detect register */
+ CMD_CMSAS_OOB_DET = 0x108, /* COMSAS OOB detect register */
+ CMD_BRST_OOB_DET = 0x10c, /* burst OOB detect register */
+ CMD_OOB_SPACE = 0x110, /* OOB space control register */
+ CMD_OOB_BURST = 0x114, /* OOB burst control register */
+ CMD_PHY_TIMER = 0x118, /* PHY timer control register */
+ CMD_PHY_CONFIG0 = 0x11c, /* PHY config register 0 */
+ CMD_PHY_CONFIG1 = 0x120, /* PHY config register 1 */
+ CMD_SAS_CTL0 = 0x124, /* SAS control register 0 */
+ CMD_SAS_CTL1 = 0x128, /* SAS control register 1 */
+ CMD_SAS_CTL2 = 0x12c, /* SAS control register 2 */
+ CMD_SAS_CTL3 = 0x130, /* SAS control register 3 */
+ CMD_ID_TEST = 0x134, /* ID test register */
+ CMD_PL_TIMER = 0x138, /* PL timer register */
+ CMD_WD_TIMER = 0x13c, /* WD timer register */
+ CMD_PORT_SEL_COUNT = 0x140, /* port selector count register */
+ CMD_APP_MEM_CTL = 0x144, /* Application Memory Control */
+ CMD_XOR_MEM_CTL = 0x148, /* XOR Block Memory Control */
+ CMD_DMA_MEM_CTL = 0x14c, /* DMA Block Memory Control */
+ CMD_PORT_MEM_CTL0 = 0x150, /* Port Memory Control 0 */
+ CMD_PORT_MEM_CTL1 = 0x154, /* Port Memory Control 1 */
+ CMD_SATA_PORT_MEM_CTL0 = 0x158, /* SATA Port Memory Control 0 */
+ CMD_SATA_PORT_MEM_CTL1 = 0x15c, /* SATA Port Memory Control 1 */
+ CMD_XOR_MEM_BIST_CTL = 0x160, /* XOR Memory BIST Control */
+ CMD_XOR_MEM_BIST_STAT = 0x164, /* XOR Memroy BIST Status */
+ CMD_DMA_MEM_BIST_CTL = 0x168, /* DMA Memory BIST Control */
+ CMD_DMA_MEM_BIST_STAT = 0x16c, /* DMA Memory BIST Status */
+ CMD_PORT_MEM_BIST_CTL = 0x170, /* Port Memory BIST Control */
+ CMD_PORT_MEM_BIST_STAT0 = 0x174, /* Port Memory BIST Status 0 */
+ CMD_PORT_MEM_BIST_STAT1 = 0x178, /* Port Memory BIST Status 1 */
+ CMD_STP_MEM_BIST_CTL = 0x17c, /* STP Memory BIST Control */
+ CMD_STP_MEM_BIST_STAT0 = 0x180, /* STP Memory BIST Status 0 */
+ CMD_STP_MEM_BIST_STAT1 = 0x184, /* STP Memory BIST Status 1 */
+ CMD_RESET_COUNT = 0x188, /* Reset Count */
+ CMD_MONTR_DATA_SEL = 0x18C, /* Monitor Data/Select */
+ CMD_PLL_PHY_CONFIG = 0x190, /* PLL/PHY Configuration */
+ CMD_PHY_CTL = 0x194, /* PHY Control and Status */
+ CMD_PHY_TEST_COUNT0 = 0x198, /* Phy Test Count 0 */
+ CMD_PHY_TEST_COUNT1 = 0x19C, /* Phy Test Count 1 */
+ CMD_PHY_TEST_COUNT2 = 0x1A0, /* Phy Test Count 2 */
+ CMD_APP_ERR_CONFIG = 0x1A4, /* Application Error Configuration */
+ CMD_PND_FIFO_CTL0 = 0x1A8, /* Pending FIFO Control 0 */
+ CMD_HOST_CTL = 0x1AC, /* Host Control Status */
+ CMD_HOST_WR_DATA = 0x1B0, /* Host Write Data */
+ CMD_HOST_RD_DATA = 0x1B4, /* Host Read Data */
+ CMD_PHY_MODE_21 = 0x1B8, /* Phy Mode 21 */
+ CMD_SL_MODE0 = 0x1BC, /* SL Mode 0 */
+ CMD_SL_MODE1 = 0x1C0, /* SL Mode 1 */
+ CMD_PND_FIFO_CTL1 = 0x1C4, /* Pending FIFO Control 1 */
+};
+
+enum pci_cfg_register_bits {
+ PCTL_PWR_ON = (0xFU << 24),
+ PCTL_OFF = (0xFU << 12),
+ PRD_REQ_SIZE = (0x4000),
+ PRD_REQ_MASK = (0x00007000),
+};
+
+enum nvram_layout_offsets {
+ NVR_SIG = 0x00, /* 0xAA, 0x55 */
+ NVR_SAS_ADDR = 0x02, /* 8-byte SAS address */
+};
+
+enum chip_flavors {
+ chip_6320,
+ chip_6440,
+ chip_6480,
+};
+
+enum port_type {
+ PORT_TYPE_SAS = (1L << 1),
+ PORT_TYPE_SATA = (1L << 0),
+};
+
+/* Command Table Format */
+enum ct_format {
+ /* SSP */
+ SSP_F_H = 0x00,
+ SSP_F_IU = 0x18,
+ SSP_F_MAX = 0x4D,
+ /* STP */
+ STP_CMD_FIS = 0x00,
+ STP_ATAPI_CMD = 0x40,
+ STP_F_MAX = 0x10,
+ /* SMP */
+ SMP_F_T = 0x00,
+ SMP_F_DEP = 0x01,
+ SMP_F_MAX = 0x101,
+};
+
+enum status_buffer {
+ SB_EIR_OFF = 0x00, /* Error Information Record */
+ SB_RFB_OFF = 0x08, /* Response Frame Buffer */
+ SB_RFB_MAX = 0x400, /* RFB size*/
+};
+
+enum error_info_rec {
+ CMD_ISS_STPD = (1U << 31), /* Cmd Issue Stopped */
+ CMD_PI_ERR = (1U << 30), /* Protection info error. see flags2 */
+ RSP_OVER = (1U << 29), /* rsp buffer overflow */
+ RETRY_LIM = (1U << 28), /* FIS/frame retry limit exceeded */
+ UNK_FIS = (1U << 27), /* unknown FIS */
+ DMA_TERM = (1U << 26), /* DMA terminate primitive rx'd */
+ SYNC_ERR = (1U << 25), /* SYNC rx'd during frame xmit */
+ TFILE_ERR = (1U << 24), /* SATA taskfile Error bit set */
+ R_ERR = (1U << 23), /* SATA returned R_ERR prim */
+ RD_OFS = (1U << 20), /* Read DATA frame invalid offset */
+ XFER_RDY_OFS = (1U << 19), /* XFER_RDY offset error */
+ UNEXP_XFER_RDY = (1U << 18), /* unexpected XFER_RDY error */
+ DATA_OVER_UNDER = (1U << 16), /* data overflow/underflow */
+ INTERLOCK = (1U << 15), /* interlock error */
+ NAK = (1U << 14), /* NAK rx'd */
+ ACK_NAK_TO = (1U << 13), /* ACK/NAK timeout */
+ CXN_CLOSED = (1U << 12), /* cxn closed w/out ack/nak */
+ OPEN_TO = (1U << 11), /* I_T nexus lost, open cxn timeout */
+ PATH_BLOCKED = (1U << 10), /* I_T nexus lost, pathway blocked */
+ NO_DEST = (1U << 9), /* I_T nexus lost, no destination */
+ STP_RES_BSY = (1U << 8), /* STP resources busy */
+ BREAK = (1U << 7), /* break received */
+ BAD_DEST = (1U << 6), /* bad destination */
+ BAD_PROTO = (1U << 5), /* protocol not supported */
+ BAD_RATE = (1U << 4), /* cxn rate not supported */
+ WRONG_DEST = (1U << 3), /* wrong destination error */
+ CREDIT_TO = (1U << 2), /* credit timeout */
+ WDOG_TO = (1U << 1), /* watchdog timeout */
+ BUF_PAR = (1U << 0), /* buffer parity error */
+};
+
+enum error_info_rec_2 {
+ SLOT_BSY_ERR = (1U << 31), /* Slot Busy Error */
+ GRD_CHK_ERR = (1U << 14), /* Guard Check Error */
+ APP_CHK_ERR = (1U << 13), /* Application Check error */
+ REF_CHK_ERR = (1U << 12), /* Reference Check Error */
+ USR_BLK_NM = (1U << 0), /* User Block Number */
+};
+
+#endif