spelling fixes: arch/sh/
Spelling fixes in arch/sh/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
diff --git a/arch/sh/boards/landisk/gio.c b/arch/sh/boards/landisk/gio.c
index 50d38be..a37643d 100644
--- a/arch/sh/boards/landisk/gio.c
+++ b/arch/sh/boards/landisk/gio.c
@@ -69,7 +69,7 @@
}
switch (cmd) {
- case GIODRV_IOCSGIOSETADDR: /* addres set */
+ case GIODRV_IOCSGIOSETADDR: /* address set */
addr = data;
break;
diff --git a/arch/sh/boards/snapgear/rtc.c b/arch/sh/boards/snapgear/rtc.c
index 1659fdd..edb3dd9 100644
--- a/arch/sh/boards/snapgear/rtc.c
+++ b/arch/sh/boards/snapgear/rtc.c
@@ -108,7 +108,7 @@
static void ds1302_reset(void)
{
unsigned long flags;
- /* Hardware dependant reset/init */
+ /* Hardware dependent reset/init */
local_irq_save(flags);
set_dirp(get_dirp() | RTC_RESET | RTC_IODATA | RTC_SCLK);
set_dp(get_dp() & ~(RTC_RESET | RTC_IODATA | RTC_SCLK));
diff --git a/arch/sh/boards/superh/microdev/io.c b/arch/sh/boards/superh/microdev/io.c
index 83419bf..b704e20 100644
--- a/arch/sh/boards/superh/microdev/io.c
+++ b/arch/sh/boards/superh/microdev/io.c
@@ -198,12 +198,12 @@
/*
* There is a board feature with the current SH4-202 MicroDev in
* that the 2 byte enables (nBE0 and nBE1) are tied together (and
- * to the Chip Select Line (Ethernet_CS)). Due to this conectivity,
+ * to the Chip Select Line (Ethernet_CS)). Due to this connectivity,
* it is not possible to safely perform 8-bit writes to the
* Ethernet registers, as 16-bits will be consumed from the Data
* lines (corrupting the other byte). Hence, this function is
- * written to impliment 16-bit read/modify/write for all byte-wide
- * acceses.
+ * written to implement 16-bit read/modify/write for all byte-wide
+ * accesses.
*
* Note: there is no problem with byte READS (even or odd).
*
diff --git a/arch/sh/boards/superh/microdev/irq.c b/arch/sh/boards/superh/microdev/irq.c
index 8c64baa..cc1cb04 100644
--- a/arch/sh/boards/superh/microdev/irq.c
+++ b/arch/sh/boards/superh/microdev/irq.c
@@ -100,7 +100,7 @@
fpgaIrq = fpgaIrqTable[irq].fpgaIrq;
- /* disable interupts on the FPGA INTC register */
+ /* disable interrupts on the FPGA INTC register */
ctrl_outl(MICRODEV_FPGA_INTC_MASK(fpgaIrq), MICRODEV_FPGA_INTDSB_REG);
}
@@ -125,7 +125,7 @@
priorities |= MICRODEV_FPGA_INTPRI_LEVEL(fpgaIrq, pri);
ctrl_outl(priorities, priorityReg);
- /* enable interupts on the FPGA INTC register */
+ /* enable interrupts on the FPGA INTC register */
ctrl_outl(MICRODEV_FPGA_INTC_MASK(fpgaIrq), MICRODEV_FPGA_INTENB_REG);
}
@@ -152,7 +152,7 @@
{
int i;
- /* disable interupts on the FPGA INTC register */
+ /* disable interrupts on the FPGA INTC register */
ctrl_outl(~0ul, MICRODEV_FPGA_INTDSB_REG);
for (i = 0; i < NUM_EXTERNAL_IRQS; i++)
diff --git a/arch/sh/boards/superh/microdev/setup.c b/arch/sh/boards/superh/microdev/setup.c
index 031c814..6396cea 100644
--- a/arch/sh/boards/superh/microdev/setup.c
+++ b/arch/sh/boards/superh/microdev/setup.c
@@ -349,7 +349,7 @@
SMSC_WRITE_INDEXED(0x00, 0xc7); /* GP47 = nIOWOP */
SMSC_WRITE_INDEXED(0x08, 0xe8); /* GP20 = nIDE2_OE */
- /* Exit the configuraton state */
+ /* Exit the configuration state */
outb(SMSC_EXIT_CONFIG_KEY, SMSC_CONFIG_PORT_ADDR);
return 0;
diff --git a/arch/sh/boards/unknown/setup.c b/arch/sh/boards/unknown/setup.c
index 1c94137..bee4612 100644
--- a/arch/sh/boards/unknown/setup.c
+++ b/arch/sh/boards/unknown/setup.c
@@ -6,7 +6,7 @@
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
- * Setup code for an unknown machine (internal peripherials only)
+ * Setup code for an unknown machine (internal peripherals only)
*
* This is the simplest of all boards, and serves only as a quick and dirty
* method to start debugging a new board during bring-up until proper board