xen: set IO permission early (before early_cpu_init())
This patch is based off "xen dom0: Set up basic IO permissions for dom0."
by Juan Quintela <quintela@redhat.com>.
On AMD machines when we boot the kernel as Domain 0 we get this nasty:
mapping kernel into physical memory
Xen: setup ISA identity maps
about to get started...
(XEN) traps.c:475:d0 Unhandled general protection fault fault/trap [#13] on VCPU 0 [ec=0000]
(XEN) domain_crash_sync called from entry.S
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.1-101116 x86_64 debug=y Not tainted ]----
(XEN) CPU: 0
(XEN) RIP: e033:[<ffffffff8130271b>]
(XEN) RFLAGS: 0000000000000282 EM: 1 CONTEXT: pv guest
(XEN) rax: 000000008000c068 rbx: ffffffff8186c680 rcx: 0000000000000068
(XEN) rdx: 0000000000000cf8 rsi: 000000000000c000 rdi: 0000000000000000
(XEN) rbp: ffffffff81801e98 rsp: ffffffff81801e50 r8: ffffffff81801eac
(XEN) r9: ffffffff81801ea8 r10: ffffffff81801eb4 r11: 00000000ffffffff
(XEN) r12: ffffffff8186c694 r13: ffffffff81801f90 r14: ffffffffffffffff
(XEN) r15: 0000000000000000 cr0: 000000008005003b cr4: 00000000000006f0
(XEN) cr3: 0000000221803000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: e02b cs: e033
(XEN) Guest stack trace from rsp=ffffffff81801e50:
RIP points to read_pci_config() function.
The issue is that we don't set IO permissions for the Linux kernel early enough.
The call sequence used to be:
xen_start_kernel()
x86_init.oem.arch_setup = xen_setup_arch;
setup_arch:
- early_cpu_init
- early_init_amd
- read_pci_config
- x86_init.oem.arch_setup [ xen_arch_setup ]
- set IO permissions.
We need to set the IO permissions earlier on, which this patch does.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
diff --git a/arch/x86/xen/enlighten.c b/arch/x86/xen/enlighten.c
index bd35549..7250bef 100644
--- a/arch/x86/xen/enlighten.c
+++ b/arch/x86/xen/enlighten.c
@@ -1095,6 +1095,8 @@
/* First C function to be called on Xen boot */
asmlinkage void __init xen_start_kernel(void)
{
+ struct physdev_set_iopl set_iopl;
+ int rc;
pgd_t *pgd;
if (!xen_start_info)
@@ -1209,10 +1211,18 @@
#else
pv_info.kernel_rpl = 0;
#endif
-
/* set the limit of our address space */
xen_reserve_top();
+ /* We used to do this in xen_arch_setup, but that is too late on AMD
+ * were early_cpu_init (run before ->arch_setup()) calls early_amd_init
+ * which pokes 0xcf8 port.
+ */
+ set_iopl.iopl = 1;
+ rc = HYPERVISOR_physdev_op(PHYSDEVOP_set_iopl, &set_iopl);
+ if (rc != 0)
+ xen_raw_printk("physdev_op failed %d\n", rc);
+
#ifdef CONFIG_X86_32
/* set up basic CPUID stuff */
cpu_detect(&new_cpu_data);