pxa2xx_spi: fix chip_info defaults and documentation.
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 59ae3ed..dae87b1 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -47,6 +47,10 @@
#define MAX_BUSES 3
+#define RX_THRESH_DFLT 8
+#define TX_THRESH_DFLT 8
+#define TIMOUT_DFLT 1000
+
#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
#define IS_DMA_ALIGNED(x) ((((u32)(x)) & 0x07) == 0)
@@ -1171,6 +1175,8 @@
struct driver_data *drv_data = spi_master_get_devdata(spi->master);
struct ssp_device *ssp = drv_data->ssp;
unsigned int clk_div;
+ uint tx_thres = TX_THRESH_DFLT;
+ uint rx_thres = RX_THRESH_DFLT;
if (!spi->bits_per_word)
spi->bits_per_word = 8;
@@ -1209,8 +1215,7 @@
chip->cs_control = null_cs_control;
chip->enable_dma = 0;
- chip->timeout = 1000;
- chip->threshold = SSCR1_RxTresh(1) | SSCR1_TxTresh(1);
+ chip->timeout = TIMOUT_DFLT;
chip->dma_burst_size = drv_data->master_info->enable_dma ?
DCMD_BURST8 : 0;
}
@@ -1224,22 +1229,21 @@
if (chip_info) {
if (chip_info->cs_control)
chip->cs_control = chip_info->cs_control;
-
- chip->timeout = chip_info->timeout;
-
- chip->threshold = (SSCR1_RxTresh(chip_info->rx_threshold) &
- SSCR1_RFT) |
- (SSCR1_TxTresh(chip_info->tx_threshold) &
- SSCR1_TFT);
-
- chip->enable_dma = chip_info->dma_burst_size != 0
- && drv_data->master_info->enable_dma;
+ if (chip_info->timeout)
+ chip->timeout = chip_info->timeout;
+ if (chip_info->tx_threshold)
+ tx_thres = chip_info->tx_threshold;
+ if (chip_info->rx_threshold)
+ rx_thres = chip_info->rx_threshold;
+ chip->enable_dma = drv_data->master_info->enable_dma;
chip->dma_threshold = 0;
-
if (chip_info->enable_loopback)
chip->cr1 = SSCR1_LBM;
}
+ chip->threshold = (SSCR1_RxTresh(rx_thres) & SSCR1_RFT) |
+ (SSCR1_TxTresh(tx_thres) & SSCR1_TFT);
+
/* set dma burst and threshold outside of chip_info path so that if
* chip_info goes away after setting chip->enable_dma, the
* burst and threshold can still respond to changes in bits_per_word */
@@ -1268,17 +1272,19 @@
/* NOTE: PXA25x_SSP _could_ use external clocking ... */
if (drv_data->ssp_type != PXA25x_SSP)
- dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d\n",
+ dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d, %s\n",
spi->bits_per_word,
clk_get_rate(ssp->clk)
/ (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
- spi->mode & 0x3);
+ spi->mode & 0x3,
+ chip->enable_dma ? "DMA" : "PIO");
else
- dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d\n",
+ dev_dbg(&spi->dev, "%d bits/word, %ld Hz, mode %d, %s\n",
spi->bits_per_word,
- clk_get_rate(ssp->clk)
+ clk_get_rate(ssp->clk) / 2
/ (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
- spi->mode & 0x3);
+ spi->mode & 0x3,
+ chip->enable_dma ? "DMA" : "PIO");
if (spi->bits_per_word <= 8) {
chip->n_bytes = 1;
@@ -1498,7 +1504,9 @@
/* Load default SSP configuration */
write_SSCR0(0, drv_data->ioaddr);
- write_SSCR1(SSCR1_RxTresh(4) | SSCR1_TxTresh(12), drv_data->ioaddr);
+ write_SSCR1(SSCR1_RxTresh(RX_THRESH_DFLT) |
+ SSCR1_TxTresh(TX_THRESH_DFLT),
+ drv_data->ioaddr);
write_SSCR0(SSCR0_SerClkDiv(2)
| SSCR0_Motorola
| SSCR0_DataSize(8),