[POWERPC] Cleanup CPU inits
Cleanup CPU inits a bit more, Geoff Levand already did some earlier.
* Move CPU state save to cpu_setup, since cpu_setup is only ever done
on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
function pointers to the cputable to use instead. Powermac always
has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
everyone but powermac and iSeries use it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S
index 6ff3cf5..e9963d9 100644
--- a/arch/powerpc/kernel/head_64.S
+++ b/arch/powerpc/kernel/head_64.S
@@ -132,7 +132,7 @@
bne 100b
#if defined(CONFIG_SMP) || defined(CONFIG_KEXEC)
- LOAD_REG_IMMEDIATE(r4, .pSeries_secondary_smp_init)
+ LOAD_REG_IMMEDIATE(r4, .generic_secondary_smp_init)
mtctr r4
mr r3,r24
bctr
@@ -1484,19 +1484,17 @@
. = 0x8000
/*
- * On pSeries, secondary processors spin in the following code.
+ * On pSeries and most other platforms, secondary processors spin
+ * in the following code.
* At entry, r3 = this processor's number (physical cpu id)
*/
-_GLOBAL(pSeries_secondary_smp_init)
+_GLOBAL(generic_secondary_smp_init)
mr r24,r3
/* turn on 64-bit mode */
bl .enable_64b_mode
isync
- /* Copy some CPU settings from CPU 0 */
- bl .__restore_cpu_setup
-
/* Set up a paca value for this processor. Since we have the
* physical cpu id in r24, we need to search the pacas to find
* which logical id maps to our physical one.
@@ -1522,15 +1520,28 @@
/* start. */
sync
- /* Create a temp kernel stack for use before relocation is on. */
+#ifndef CONFIG_SMP
+ b 3b /* Never go on non-SMP */
+#else
+ cmpwi 0,r23,0
+ beq 3b /* Loop until told to go */
+
+ /* See if we need to call a cpu state restore handler */
+ LOAD_REG_IMMEDIATE(r23, cur_cpu_spec)
+ ld r23,0(r23)
+ ld r23,CPU_SPEC_RESTORE(r23)
+ cmpdi 0,r23,0
+ beq 4f
+ ld r23,0(r23)
+ mtctr r23
+ bctrl
+
+4: /* Create a temp kernel stack for use before relocation is on. */
ld r1,PACAEMERGSP(r13)
subi r1,r1,STACK_FRAME_OVERHEAD
- cmpwi 0,r23,0
-#ifdef CONFIG_SMP
- bne .__secondary_start
+ b .__secondary_start
#endif
- b 3b /* Loop until told to go */
#ifdef CONFIG_PPC_ISERIES
_STATIC(__start_initialization_iSeries)
@@ -1611,7 +1622,16 @@
bl .enable_64b_mode
/* Setup some critical 970 SPRs before switching MMU off */
- bl .__970_cpu_preinit
+ mfspr r0,SPRN_PVR
+ srwi r0,r0,16
+ cmpwi r0,0x39 /* 970 */
+ beq 1f
+ cmpwi r0,0x3c /* 970FX */
+ beq 1f
+ cmpwi r0,0x44 /* 970MP */
+ bne 2f
+1: bl .__cpu_preinit_ppc970
+2:
/* Switch off MMU if not already */
LOAD_REG_IMMEDIATE(r4, .__after_prom_start - KERNELBASE)
@@ -1782,7 +1802,7 @@
isync
/* Copy some CPU settings from CPU 0 */
- bl .__restore_cpu_setup
+ bl .__restore_cpu_ppc970
/* pSeries do that early though I don't think we really need it */
mfmsr r3
@@ -1932,12 +1952,6 @@
mr r5,r26
bl .identify_cpu
- /* Save some low level config HIDs of CPU0 to be copied to
- * other CPUs later on, or used for suspend/resume
- */
- bl .__save_cpu_setup
- sync
-
/* Do very early kernel initializations, including initial hash table,
* stab and slb setup before we turn on relocation. */