drivers/net: Move && and || to end of previous line
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index a3d9991..3943d89 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -374,8 +374,8 @@
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
/* downshift on PHY 88E1112 and 88E1149 is changed */
- if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED)
- && (hw->flags & SKY2_HW_NEWER_PHY)) {
+ if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) &&
+ (hw->flags & SKY2_HW_NEWER_PHY)) {
/* set downshift counter to 3x and enable downshift */
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
@@ -619,8 +619,8 @@
/* no effect on Yukon-XL */
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
- if ( !(sky2->flags & SKY2_FLAG_AUTO_SPEED)
- || sky2->speed == SPEED_100) {
+ if (!(sky2->flags & SKY2_FLAG_AUTO_SPEED) ||
+ sky2->speed == SPEED_100) {
/* turn on 100 Mbps LED (LED_LINK100) */
ledover |= PHY_M_LED_MO_100(MO_LED_ON);
}
@@ -937,8 +937,8 @@
/* On chips without ram buffer, pause is controled by MAC level */
if (!(hw->flags & SKY2_HW_RAM_BUFFER)) {
/* Pause threshold is scaled by 8 in bytes */
- if (hw->chip_id == CHIP_ID_YUKON_FE_P
- && hw->chip_rev == CHIP_REV_YU_FE2_A0)
+ if (hw->chip_id == CHIP_ID_YUKON_FE_P &&
+ hw->chip_rev == CHIP_REV_YU_FE2_A0)
reg = 1568 / 8;
else
reg = 1024 / 8;
@@ -1353,8 +1353,8 @@
/* These chips have no ram buffer?
* MAC Rx RAM Read is controlled by hardware */
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
- (hw->chip_rev == CHIP_REV_YU_EC_U_A1
- || hw->chip_rev == CHIP_REV_YU_EC_U_B0))
+ (hw->chip_rev == CHIP_REV_YU_EC_U_A1 ||
+ hw->chip_rev == CHIP_REV_YU_EC_U_B0))
sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
@@ -1560,8 +1560,8 @@
sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF);
/* Set almost empty threshold */
- if (hw->chip_id == CHIP_ID_YUKON_EC_U
- && hw->chip_rev == CHIP_REV_YU_EC_U_A0)
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
+ hw->chip_rev == CHIP_REV_YU_EC_U_A0)
sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV);
sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map,
@@ -1907,8 +1907,8 @@
sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET);
/* Workaround shared GMAC reset */
- if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0
- && port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
+ if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 &&
+ port == 0 && hw->dev[1] && netif_running(hw->dev[1])))
sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET);
sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
@@ -2085,8 +2085,8 @@
sky2->flow_status = FC_TX;
}
- if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
- && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
+ if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 &&
+ !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
if (sky2->flow_status & FC_TX)
@@ -3244,8 +3244,8 @@
struct sky2_port *sky2 = netdev_priv(dev);
struct sky2_hw *hw = sky2->hw;
- if ((wol->wolopts & ~sky2_wol_supported(sky2->hw))
- || !device_can_wakeup(&hw->pdev->dev))
+ if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) ||
+ !device_can_wakeup(&hw->pdev->dev))
return -EOPNOTSUPP;
sky2->wol = wol->wolopts;