| |
| -=< The IBM Microchannel SCSI-Subsystem >=- |
| |
| for the IBM PS/2 series |
| |
| Low Level Software-Driver for Linux |
| |
| Copyright (c) 1995 Strom Systems, Inc. under the terms of the GNU |
| General Public License. Originally written by Martin Kolinek, December 1995. |
| Officially modified and maintained by Michael Lang since January 1999. |
| |
| Version 4.0a |
| |
| Last update: January 3, 2001 |
| |
| Before you Start |
| ---------------- |
| This is the common README.ibmmca file for all driver releases of the |
| IBM MCA SCSI driver for Linux. Please note, that driver releases 4.0 |
| or newer do not work with kernel versions older than 2.4.0, while driver |
| versions older than 4.0 do not work with kernels 2.4.0 or later! If you |
| try to compile your kernel with the wrong driver source, the |
| compilation is aborted and you get a corresponding error message. This is |
| no bug in the driver. It prevents you from using the wrong sourcecode |
| with the wrong kernel version. |
| |
| Authors of this Driver |
| ---------------------- |
| - Chris Beauregard (improvement of the SCSI-device mapping by the driver) |
| - Martin Kolinek (origin, first release of this driver) |
| - Klaus Kudielka (multiple SCSI-host management/detection, adaption to |
| Linux Kernel 2.1.x, module support) |
| - Michael Lang (assigning original pun/lun mapping, dynamical ldn |
| assignment, rewritten adapter detection, this file, |
| patches, official driver maintenance and subsequent |
| debugging, related with the driver) |
| |
| Table of Contents |
| ----------------- |
| 1 Abstract |
| 2 Driver Description |
| 2.1 IBM SCSI-Subsystem Detection |
| 2.2 Physical Units, Logical Units, and Logical Devices |
| 2.3 SCSI-Device Recognition and dynamical ldn Assignment |
| 2.4 SCSI-Device Order |
| 2.5 Regular SCSI-Command-Processing |
| 2.6 Abort & Reset Commands |
| 2.7 Disk Geometry |
| 2.8 Kernel Boot Option |
| 2.9 Driver Module Support |
| 2.10 Multiple Hostadapter Support |
| 2.11 /proc/scsi-Filesystem Information |
| 2.12 /proc/mca-Filesystem Information |
| 2.13 Supported IBM SCSI-Subsystems |
| 2.14 Linux Kernel Versions |
| 3 Code History |
| 4 To do |
| 5 Users' Manual |
| 5.1 Commandline Parameters |
| 5.2 Troubleshooting |
| 5.3 Bugreports |
| 5.4 Support WWW-page |
| 6 References |
| 7 Credits to |
| 7.1 People |
| 7.2 Sponsors & Supporters |
| 8 Trademarks |
| 9 Disclaimer |
| |
| * * * |
| |
| 1 Abstract |
| ---------- |
| This README-file describes the IBM SCSI-subsystem low level driver for |
| Linux. The descriptions which were formerly kept in the source-code have |
| been taken out to this file to easify the codes' readability. The driver |
| description has been updated, as most of the former description was already |
| quite outdated. The history of the driver development is also kept inside |
| here. Multiple historical developments have been summarized to shorten the |
| textsize a bit. At the end of this file you can find a small manual for |
| this driver and hints to get it running on your machine. |
| |
| 2 Driver Description |
| -------------------- |
| 2.1 IBM SCSI-Subsystem Detection |
| -------------------------------- |
| This is done in the ibmmca_detect() function. It first checks, if the |
| Microchannel-bus support is enabled, as the IBM SCSI-subsystem needs the |
| Microchannel. In a next step, a free interrupt is chosen and the main |
| interrupt handler is connected to it to handle answers of the SCSI- |
| subsystem(s). If the F/W SCSI-adapter is forced by the BIOS to use IRQ11 |
| instead of IRQ14, IRQ11 is used for the IBM SCSI-2 F/W adapter. In a |
| further step it is checked, if the adapter gets detected by force from |
| the kernel commandline, where the I/O port and the SCSI-subsystem id can |
| be specified. The next step checks if there is an integrated SCSI-subsystem |
| installed. This register area is fixed through all IBM PS/2 MCA-machines |
| and appears as something like a virtual slot 10 of the MCA-bus. On most |
| PS/2 machines, the POS registers of slot 10 are set to 0xff or 0x00 if not |
| integrated SCSI-controller is available. But on certain PS/2s, like model |
| 9595, this slot 10 is used to store other information which at earlier |
| stage confused the driver and resulted in the detection of some ghost-SCSI. |
| If POS-register 2 and 3 are not 0x00 and not 0xff, but all other POS |
| registers are either 0xff or 0x00, there must be an integrated SCSI- |
| subsystem present and it will be registered as IBM Integrated SCSI- |
| Subsystem. The next step checks, if there is a slot-adapter installed on |
| the MCA-bus. To get this, the first two POS-registers, that represent the |
| adapter ID are checked. If they fit to one of the ids, stored in the |
| adapter list, a SCSI-subsystem is assumed to be found in a slot and will be |
| registered. This check is done through all possible MCA-bus slots to allow |
| more than one SCSI-adapter to be present in the PS/2-system and this is |
| already the first point of problems. Looking into the technical reference |
| manual for the IBM PS/2 common interfaces, the POS2 register must have |
| different interpretation of its single bits to avoid overlapping I/O |
| regions. While one can assume, that the integrated subsystem has a fix |
| I/O-address at 0x3540 - 0x3547, further installed IBM SCSI-adapters must |
| use a different I/O-address. This is expressed by bit 1 to 3 of POS2 |
| (multiplied by 8 + 0x3540). Bits 2 and 3 are reserved for the integrated |
| subsystem, but not for the adapters! The following list shows, how the |
| bits of POS2 and POS3 should be interpreted. |
| |
| The POS2-register of all PS/2 models' integrated SCSI-subsystems has the |
| following interpretation of bits: |
| Bit 7 - 4 : Chip Revision ID (Release) |
| Bit 3 - 2 : Reserved |
| Bit 1 : 8k NVRAM Disabled |
| Bit 0 : Chip Enable (EN-Signal) |
| The POS3-register is interpreted as follows (for most IBM SCSI-subsys.): |
| Bit 7 - 5 : SCSI ID |
| Bit 4 - 0 : Reserved = 0 |
| The slot-adapters have different interpretation of these bits. The IBM SCSI |
| adapter (w/Cache) and the IBM SCSI-2 F/W adapter use the following |
| interpretation of the POS2 register: |
| Bit 7 - 4 : ROM Segment Address Select |
| Bit 3 - 1 : Adapter I/O Address Select (*8+0x3540) |
| Bit 0 : Adapter Enable (EN-Signal) |
| and for the POS3 register: |
| Bit 7 - 5 : SCSI ID |
| Bit 4 : Fairness Enable (SCSI ID3 f. F/W) |
| Bit 3 - 0 : Arbitration Level |
| The most modern product of the series is the IBM SCSI-2 F/W adapter, it |
| allows dual-bus SCSI and SCSI-wide addressing, which means, PUNs may be |
| between 0 and 15. Here, Bit 4 is the high-order bit of the 4-bit wide |
| adapter PUN expression. In short words, this means, that IBM PS/2 machines |
| can only support 1 single integrated subsystem by default. Additional |
| slot-adapters get ports assigned by the automatic configuration tool. |
| |
| One day I found a patch in ibmmca_detect(), forcing the I/O-address to be |
| 0x3540 for integrated SCSI-subsystems, there was a remark placed, that on |
| integrated IBM SCSI-subsystems of model 56, the POS2 register was showing 5. |
| This means, that really for these models, POS2 has to be interpreted |
| sticking to the technical reference guide. In this case, the bit 2 (4) is |
| a reserved bit and may not be interpreted. These differences between the |
| adapters and the integrated controllers are taken into account by the |
| detection routine of the driver on from version >3.0g. |
| |
| Every time, a SCSI-subsystem is discovered, the ibmmca_register() function |
| is called. This function checks first, if the requested area for the I/O- |
| address of this SCSI-subsystem is still available and assigns this I/O- |
| area to the SCSI-subsystem. There are always 8 sequential I/O-addresses |
| taken for each individual SCSI-subsystem found, which are: |
| |
| Offset Type Permissions |
| 0 Command Interface Register 1 Read/Write |
| 1 Command Interface Register 2 Read/Write |
| 2 Command Interface Register 3 Read/Write |
| 3 Command Interface Register 4 Read/Write |
| 4 Attention Register Read/Write |
| 5 Basic Control Register Read/Write |
| 6 Interrupt Status Register Read |
| 7 Basic Status Register Read |
| |
| After the I/O-address range is assigned, the host-adapter is assigned |
| to a local structure which keeps all adapter information needed for the |
| driver itself and the mid- and higher-level SCSI-drivers. The SCSI pun/lun |
| and the adapters' ldn tables are initialized and get probed afterwards by |
| the check_devices() function. If no further adapters are found, |
| ibmmca_detect() quits. |
| |
| 2.2 Physical Units, Logical Units, and Logical Devices |
| ------------------------------------------------------ |
| There can be up to 56 devices on the SCSI bus (besides the adapter): |
| there are up to 7 "physical units" (each identified by physical unit |
| number or pun, also called the scsi id, this is the number you select |
| with hardware jumpers), and each physical unit can have up to 8 |
| "logical units" (each identified by logical unit number, or lun, |
| between 0 and 7). The IBM SCSI-2 F/W adapter offers this on up to two |
| busses and provides support for 30 logical devices at the same time, where |
| in wide-addressing mode you can have 16 puns with 32 luns on each device. |
| This section dexribes you the handling of devices on non-F/W adapters. |
| Just imagine, that you can have 16 * 32 = 512 devices on a F/W adapter |
| which means a lot of possible devices for such a small machine. |
| |
| Typically the adapter has pun=7, so puns of other physical units |
| are between 0 and 6(15). On a wide-adapter a pun higher than 7 is |
| possible, but is normally not used. Almost all physical units have only |
| one logical unit, with lun=0. A CD-ROM jukebox would be an example of a |
| physical unit with more than one logical unit. |
| |
| The embedded microprocessor of the IBM SCSI-subsystem hides the complex |
| two-dimensional (pun,lun) organization from the operating system. |
| When the machine is powered-up (or rebooted), the embedded microprocessor |
| checks, on its own, all 56 possible (pun,lun) combinations, and the first |
| 15 devices found are assigned into a one-dimensional array of so-called |
| "logical devices", identified by "logical device numbers" or ldn. The last |
| ldn=15 is reserved for the subsystem itself. Wide adapters may have |
| to check up to 15 * 8 = 120 pun/lun combinations. |
| |
| 2.3 SCSI-Device Recognition and Dynamical ldn Assignment |
| -------------------------------------------------------- |
| One consequence of information hiding is that the real (pun,lun) |
| numbers are also hidden. The two possibilities to get around this problem |
| is to offer fake pun/lun combinations to the operating system or to |
| delete the whole mapping of the adapter and to reassign the ldns, using |
| the immediate assign command of the SCSI-subsystem for probing through |
| all possible pun/lun combinations. a ldn is a "logical device number" |
| which is used by IBM SCSI-subsystems to access some valid SCSI-device. |
| At the beginning of the development of this driver, the following approach |
| was used: |
| |
| First, the driver checked the ldn's (0 to 6) to find out which ldn's |
| have devices assigned. This was done by the functions check_devices() and |
| device_exists(). The interrupt handler has a special paragraph of code |
| (see local_checking_phase_flag) to assist in the checking. Assume, for |
| example, that three logical devices were found assigned at ldn 0, 1, 2. |
| These are presented to the upper layer of Linux SCSI driver |
| as devices with bogus (pun, lun) equal to (0,0), (1,0), (2,0). |
| On the other hand, if the upper layer issues a command to device |
| say (4,0), this driver returns DID_NO_CONNECT error. |
| |
| In a second step of the driver development, the following improvement has |
| been applied: The first approach limited the number of devices to 7, far |
| fewer than the 15 that it could usem then it just maped ldn -> |
| (ldn/8,ldn%8) for pun,lun. We ended up with a real mishmash of puns |
| and luns, but it all seemed to work. |
| |
| The latest development, which is implemented from the driver version 3.0 |
| and later, realizes the device recognition in the following way: |
| The physical SCSI-devices on the SCSI-bus are probed via immediate_assign- |
| and device_inquiry-commands, that is all implemented in a completely new |
| made check_devices() subroutine. This delivers an exact map of the physical |
| SCSI-world that is now stored in the get_scsi[][]-array. This means, |
| that the once hidden pun,lun assignment is now known to this driver. |
| It no longer believes in default-settings of the subsystem and maps all |
| ldns to existing pun,lun "by foot". This assures full control of the ldn |
| mapping and allows dynamical remapping of ldns to different pun,lun, if |
| there are more SCSI-devices installed than ldns available (n>15). The |
| ldns from 0 to 6 get 'hardwired' by this driver to puns 0 to 7 at lun=0, |
| excluding the pun of the subsystem. This assures, that at least simple |
| SCSI-installations have optimum access-speed and are not touched by |
| dynamical remapping. The ldns 7 to 14 are put to existing devices with |
| lun>0 or to non-existing devices, in order to satisfy the subsystem, if |
| there are less than 15 SCSI-devices connected. In the case of more than 15 |
| devices, the dynamical mapping goes active. If the get_scsi[][] reports a |
| device to be existant, but it has no ldn assigned, it gets a ldn out of 7 |
| to 14. The numbers are assigned in cyclic order. Therefore it takes 8 |
| dynamical reassignments on the SCSI-devices, until a certain device |
| loses its ldn again. This assures, that dynamical remapping is avoided |
| during intense I/O between up to 15 SCSI-devices (means pun,lun |
| combinations). A further advantage of this method is, that people who |
| build their kernel without probing on all luns will get what they expect, |
| because the driver just won't assign everything with lun>0 when |
| multpile lun probing is inactive. |
| |
| 2.4 SCSI-Device Order |
| --------------------- |
| Because of the now correct recognition of physical pun,lun, and |
| their report to mid-level- and higher-level-drivers, the new reported puns |
| can be different from the old, faked puns. Therefore, Linux will eventually |
| change /dev/sdXXX assignments and prompt you for corrupted superblock |
| repair on boottime. In this case DO NOT PANIC, YOUR DISKS ARE STILL OK!!! |
| You have to reboot (CTRL-D) with an old kernel and set the /etc/fstab-file |
| entries right. After that, the system should come up as errorfree as before. |
| If your boot-partition is not coming up, also edit the /etc/lilo.conf-file |
| in a Linux session booted on old kernel and run lilo before reboot. Check |
| lilo.conf anyway to get boot on other partitions with foreign OSes right |
| again. But there exists a feature of this driver that allows you to change |
| the assignment order of the SCSI-devices by flipping the PUN-assignment. |
| See the next paragraph for a description. |
| |
| The problem for this is, that Linux does not assign the SCSI-devices in the |
| way as described in the ANSI-SCSI-standard. Linux assigns /dev/sda to |
| the device with at minimum id 0. But the first drive should be at id 6, |
| because for historical reasons, drive at id 6 has, by hardware, the highest |
| priority and a drive at id 0 the lowest. IBM was one of the rare producers, |
| where the BIOS assigns drives belonging to the ANSI-SCSI-standard. Most |
| other producers' BIOS does not (I think even Adaptec-BIOS). The |
| IBMMCA_SCSI_ORDER_STANDARD flag, which you set while configuring the |
| kernel enables to choose the preferred way of SCSI-device-assignment. |
| Defining this flag would result in Linux determining the devices in the |
| same order as DOS and OS/2 does on your MCA-machine. This is also standard |
| on most industrial computers and OSes, like e.g. OS-9. Leaving this flag |
| undefined will get your devices ordered in the default way of Linux. See |
| also the remarks of Chris Beauregard from Dec 15, 1997 and the followups |
| in section 3. |
| |
| 2.5 Regular SCSI-Command-Processing |
| ----------------------------------- |
| Only three functions get involved: ibmmca_queuecommand(), issue_cmd(), |
| and interrupt_handler(). |
| |
| The upper layer issues a scsi command by calling function |
| ibmmca_queuecommand(). This function fills a "subsystem control block" |
| (scb) and calls a local function issue_cmd(), which writes a scb |
| command into subsystem I/O ports. Once the scb command is carried out, |
| the interrupt_handler() is invoked. If a device is determined to be |
| existant and it has not assigned any ldn, it gets one dynamically. |
| For this, the whole stuff is done in ibmmca_queuecommand(). |
| |
| 2.6 Abort & Reset Commands |
| -------------------------- |
| These are implemented with busy waiting for interrupt to arrive. |
| ibmmca_reset() and ibmmca_abort() do not work sufficently well |
| up to now and need still a lot of development work. But, this seems |
| to be even a problem with other SCSI-low level drivers, too. However, |
| this should be no excuse. |
| |
| 2.7 Disk Geometry |
| ----------------- |
| The ibmmca_biosparams() function should return the same disk geometry |
| as the bios. This is needed for fdisk, etc. The returned geometry is |
| certainly correct for disks smaller than 1 gigabyte. In the meantime, |
| it has been proved, that this works fine even with disks larger than |
| 1 gigabyte. |
| |
| 2.8 Kernel Boot Option |
| ---------------------- |
| The function ibmmca_scsi_setup() is called if option ibmmcascsi=n |
| is passed to the kernel. See file linux/init/main.c for details. |
| |
| 2.9 Driver Module Support |
| ------------------------- |
| Is implemented and tested by K. Kudielka. This could probably not work |
| on kernels <2.1.0. |
| |
| 2.10 Multiple Hostadapter Support |
| --------------------------------- |
| This driver supports up to eight interfaces of type IBM-SCSI-Subsystem. |
| Integrated-, and MCA-adapters are automatically recognized. Unrecognizable |
| IBM-SCSI-Subsystem interfaces can be specified as kernel-parameters. |
| |
| 2.11 /proc/scsi-Filesystem Information |
| -------------------------------------- |
| Information about the driver condition is given in |
| /proc/scsi/ibmmca/<host_no>. ibmmca_proc_info() provides this information. |
| |
| This table is quite informative for interested users. It shows the load |
| of commands on the subsystem and whether you are running the bypassed |
| (software) or integrated (hardware) SCSI-command set (see below). The |
| amount of accesses is shown. Read, write, modeselect is shown separately |
| in order to help debugging problems with CD-ROMs or tapedrives. |
| |
| The following table shows the list of 15 logical device numbers, that are |
| used by the SCSI-subsystem. The load on each ldn is shown in the table, |
| again, read and write commands are split. The last column shows the amount |
| of reassignments, that have been applied to the ldns, if you have more than |
| 15 pun/lun combinations available on the SCSI-bus. |
| |
| The last two tables show the pun/lun map and the positions of the ldns |
| on this pun/lun map. This may change during operation, when a ldn is |
| reassigned to another pun/lun combination. If the necessity for dynamical |
| assignments is set to 'no', the ldn structure keeps static. |
| |
| 2.12 /proc/mca-Filesystem Information |
| ------------------------------------- |
| The slot-file contains all default entries and in addition chip and I/O- |
| address information of the SCSI-subsystem. This information is provided |
| by ibmmca_getinfo(). |
| |
| 2.13 Supported IBM SCSI-Subsystems |
| ---------------------------------- |
| The following IBM SCSI-subsystems are supported by this driver: |
| |
| - IBM Fast/Wide SCSI-2 Adapter |
| - IBM 7568 Industrial Computer SCSI Adapter w/Cache |
| - IBM Expansion Unit SCSI Controller |
| - IBM SCSI Adapter w/Cache |
| - IBM SCSI Adapter |
| - IBM Integrated SCSI Controller |
| - All clones, 100% compatible with the chipset and subsystem command |
| system of IBM SCSI-adapters (forced detection) |
| |
| 2.14 Linux Kernel Versions |
| -------------------------- |
| The IBM SCSI-subsystem low level driver is prepared to be used with |
| all versions of Linux between 2.0.x and 2.4.x. The compatibility checks |
| are fully implemented up from version 3.1e of the driver. This means, that |
| you just need the latest ibmmca.h and ibmmca.c file and copy it in the |
| linux/drivers/scsi directory. The code is automatically adapted during |
| kernel compilation. This is different from kernel 2.4.0! Here version |
| 4.0 or later of the driver must be used for kernel 2.4.0 or later. Version |
| 4.0 or later does not work together with older kernels! Driver versions |
| older than 4.0 do not work together with kernel 2.4.0 or later. They work |
| on all older kernels. |
| |
| 3 Code History |
| -------------- |
| Jan 15 1996: First public release. |
| - Martin Kolinek |
| |
| Jan 23 1996: Scrapped code which reassigned scsi devices to logical |
| device numbers. Instead, the existing assignment (created |
| when the machine is powered-up or rebooted) is used. |
| A side effect is that the upper layer of Linux SCSI |
| device driver gets bogus scsi ids (this is benign), |
| and also the hard disks are ordered under Linux the |
| same way as they are under dos (i.e., C: disk is sda, |
| D: disk is sdb, etc.). |
| - Martin Kolinek |
| |
| I think that the CD-ROM is now detected only if a CD is |
| inside CD_ROM while Linux boots. This can be fixed later, |
| once the driver works on all types of PS/2's. |
| - Martin Kolinek |
| |
| Feb 7 1996: Modified biosparam function. Fixed the CD-ROM detection. |
| For now, devices other than harddisk and CD_ROM are |
| ignored. Temporarily modified abort() function |
| to behave like reset(). |
| - Martin Kolinek |
| |
| Mar 31 1996: The integrated scsi subsystem is correctly found |
| in PS/2 models 56,57, but not in model 76. Therefore |
| the ibmmca_scsi_setup() function has been added today. |
| This function allows the user to force detection of |
| scsi subsystem. The kernel option has format |
| ibmmcascsi=n |
| where n is the scsi_id (pun) of the subsystem. Most likely, n is 7. |
| - Martin Kolinek |
| |
| Aug 21 1996: Modified the code which maps ldns to (pun,0). It was |
| insufficient for those of us with CD-ROM changers. |
| - Chris Beauregard |
| |
| Dec 14 1996: More improvements to the ldn mapping. See check_devices |
| for details. Did more fiddling with the integrated SCSI detection, |
| but I think it's ultimately hopeless without actually testing the |
| model of the machine. The 56, 57, 76 and 95 (ultimedia) all have |
| different integrated SCSI register configurations. However, the 56 |
| and 57 are the only ones that have problems with forced detection. |
| - Chris Beauregard |
| |
| Mar 8-16 1997: Modified driver to run as a module and to support |
| multiple adapters. A structure, called ibmmca_hostdata, is now |
| present, containing all the variables, that were once only |
| available for one single adapter. The find_subsystem-routine has vanished. |
| The hardware recognition is now done in ibmmca_detect directly. |
| This routine checks for presence of MCA-bus, checks the interrupt |
| level and continues with checking the installed hardware. |
| Certain PS/2-models do not recognize a SCSI-subsystem automatically. |
| Hence, the setup defined by command-line-parameters is checked first. |
| Thereafter, the routine probes for an integrated SCSI-subsystem. |
| Finally, adapters are checked. This method has the advantage to cover all |
| possible combinations of multiple SCSI-subsystems on one MCA-board. Up to |
| eight SCSI-subsystems can be recognized and announced to the upper-level |
| drivers with this improvement. A set of defines made changes to other |
| routines as small as possible. |
| - Klaus Kudielka |
| |
| May 30 1997: (v1.5b) |
| 1) SCSI-command capability enlarged by the recognition of MODE_SELECT. |
| This needs the RD-Bit to be disabled on IM_OTHER_SCSI_CMD_CMD which |
| allows data to be written from the system to the device. It is a |
| necessary step to be allowed to set blocksize of SCSI-tape-drives and |
| the tape-speed, whithout confusing the SCSI-Subsystem. |
| 2) The recognition of a tape is included in the check_devices routine. |
| This is done by checking for TYPE_TAPE, that is already defined in |
| the kernel-scsi-environment. The markup of a tape is done in the |
| global ldn_is_tape[] array. If the entry on index ldn |
| is 1, there is a tapedrive connected. |
| 3) The ldn_is_tape[] array is necessary to distinguish between tape- and |
| other devices. Fixed blocklength devices should not cause a problem |
| with the SCB-command for read and write in the ibmmca_queuecommand |
| subroutine. Therefore, I only derivate the READ_XX, WRITE_XX for |
| the tape-devices, as recommended by IBM in this Technical Reference, |
| mentioned below. (IBM recommends to avoid using the read/write of the |
| subsystem, but the fact was, that read/write causes a command error from |
| the subsystem and this causes kernel-panic.) |
| 4) In addition, I propose to use the ldn instead of a fix char for the |
| display of PS2_DISK_LED_ON(). On 95, one can distinguish between the |
| devices that are accessed. It shows activity and easyfies debugging. |
| The tape-support has been tested with a SONY SDT-5200 and a HP DDS-2 |
| (I do not know yet the type). Optimization and CD-ROM audio-support, |
| I am working on ... |
| - Michael Lang |
| |
| June 19 1997: (v1.6b) |
| 1) Submitting the extra-array ldn_is_tape[] -> to the local ld[] |
| device-array. |
| 2) CD-ROM Audio-Play seems to work now. |
| 3) When using DDS-2 (120M) DAT-Tapes, mtst shows still density-code |
| 0x13 for ordinary DDS (61000 BPM) instead 0x24 for DDS-2. This appears |
| also on Adaptec 2940 adaptor in a PCI-System. Therefore, I assume that |
| the problem is independent of the low-level-driver/bus-architecture. |
| 4) Hexadecimal ldn on PS/2-95 LED-display. |
| 5) Fixing of the PS/2-LED on/off that it works right with tapedrives and |
| does not confuse the disk_rw_in_progress counter. |
| - Michael Lang |
| |
| June 21 1997: (v1.7b) |
| 1) Adding of a proc_info routine to inform in /proc/scsi/ibmmca/<host> the |
| outer-world about operational load statistics on the different ldns, |
| seen by the driver. Everybody that has more than one IBM-SCSI should |
| test this, because I only have one and cannot see what happens with more |
| than one IBM-SCSI hosts. |
| 2) Definition of a driver version-number to have a better recognition of |
| the source when there are existing too much releases that may confuse |
| the user, when reading about release-specific problems. Up to know, |
| I calculated the version-number to be 1.7. Because we are in BETA-test |
| yet, it is today 1.7b. |
| 3) Sorry for the heavy bug I programmed on June 19 1997! After that, the |
| CD-ROM did not work any more! The C7-command was a fake impression |
| I got while programming. Now, the READ and WRITE commands for CD-ROM are |
| no longer running over the subsystem, but just over |
| IM_OTHER_SCSI_CMD_CMD. On my observations (PS/2-95), now CD-ROM mounts |
| much faster(!) and hopefully all fancy multimedia-functions, like direct |
| digital recording from audio-CDs also work. (I tried it with cdda2wav |
| from the cdwtools-package and it filled up the harddisk immediately :-).) |
| To easify boolean logics, a further local device-type in ld[], called |
| is_cdrom has been included. |
| 4) If one uses a SCSI-device of unsupported type/commands, one |
| immediately runs into a kernel-panic caused by Command Error. To better |
| understand which SCSI-command caused the problem, I extended this |
| specific panic-message slightly. |
| - Michael Lang |
| |
| June 25 1997: (v1.8b) |
| 1) Some cosmetical changes for the handling of SCSI-device-types. |
| Now, also CD-Burners / WORMs and SCSI-scanners should work. For |
| MO-drives I have no experience, therefore not yet supported. |
| In logical_devices I changed from different type-variables to one |
| called 'device_type' where the values, corresponding to scsi.h, |
| of a SCSI-device are stored. |
| 2) There existed a small bug, that maps a device, coming after a SCSI-tape |
| wrong. Therefore, e.g. a CD-ROM changer would have been mapped wrong |
| -> problem removed. |
| 3) Extension of the logical_device structure. Now it contains also device, |
| vendor and revision-level of a SCSI-device for internal usage. |
| - Michael Lang |
| |
| June 26-29 1997: (v2.0b) |
| 1) The release number 2.0b is necessary because of the completely new done |
| recognition and handling of SCSI-devices with the adapter. As I got |
| from Chris the hint, that the subsystem can reassign ldns dynamically, |
| I remembered this immediate_assign-command, I found once in the handbook. |
| Now, the driver first kills all ldn assignments that are set by default |
| on the SCSI-subsystem. After that, it probes on all puns and luns for |
| devices by going through all combinations with immediate_assign and |
| probing for devices, using device_inquiry. The found physical(!) pun,lun |
| structure is stored in get_scsi[][] as device types. This is followed |
| by the assignment of all ldns to existing SCSI-devices. If more ldns |
| than devices are available, they are assigned to non existing pun,lun |
| combinations to satisfy the adapter. With this, the dynamical mapping |
| was possible to implement. (For further info see the text in the |
| source-code and in the description below. Read the description |
| below BEFORE installing this driver on your system!) |
| 2) Changed the name IBMMCA_DRIVER_VERSION to IBMMCA_SCSI_DRIVER_VERSION. |
| 3) The LED-display shows on PS/2-95 no longer the ldn, but the SCSI-ID |
| (pun) of the accessed SCSI-device. This is now senseful, because the |
| pun known within the driver is exactly the pun of the physical device |
| and no longer a fake one. |
| 4) The /proc/scsi/ibmmca/<host_no> consists now of the first part, where |
| hit-statistics of ldns is shown and a second part, where the maps of |
| physical and logical SCSI-devices are displayed. This could be very |
| interesting, when one is using more than 15 SCSI-devices in order to |
| follow the dynamical remapping of ldns. |
| - Michael Lang |
| |
| June 26-29 1997: (v2.0b-1) |
| 1) I forgot to switch the local_checking_phase_flag to 1 and back to 0 |
| in the dynamical remapping part in ibmmca_queuecommand for the |
| device_exist routine. Sorry. |
| - Michael Lang |
| |
| July 1-13 1997: (v3.0b,c) |
| 1) Merging of the driver-developments of Klaus Kudielka and Michael Lang |
| in order to get a optimum and unified driver-release for the |
| IBM-SCSI-Subsystem-Adapter(s). |
| For people, using the Kernel-release >=2.1.0, module-support should |
| be no problem. For users, running under <2.1.0, module-support may not |
| work, because the methods have changed between 2.0.x and 2.1.x. |
| 2) Added some more effective statistics for /proc-output. |
| 3) Change typecasting at necessary points from (unsigned long) to |
| virt_to_bus(). |
| 4) Included #if... at special points to have specific adaption of the |
| driver to kernel 2.0.x and 2.1.x. It should therefore also run with |
| later releases. |
| 5) Magneto-Optical drives and medium-changers are also recognized, now. |
| Therefore, we have a completely gapfree recognition of all SCSI- |
| device-types, that are known by Linux up to kernel 2.1.31. |
| 6) The flag SCSI_IBMMCA_DEV_RESET has been inserted. If it is set within |
| the configuration, each connected SCSI-device will get a reset command |
| during boottime. This can be necessary for some special SCSI-devices. |
| This flag should be included in Config.in. |
| (See also the new Config.in file.) |
| Probable next improvement: bad disk handler. |
| - Michael Lang |
| |
| Sept 14 1997: (v3.0c) |
| 1) Some debugging and speed optimization applied. |
| - Michael Lang |
| |
| Dec 15, 1997 |
| - chrisb@truespectra.com |
| - made the front panel display thingy optional, specified from the |
| command-line via ibmmcascsi=display. Along the lines of the /LED |
| option for the OS/2 driver. |
| - fixed small bug in the LED display that would hang some machines. |
| - reversed ordering of the drives (using the |
| IBMMCA_SCSI_ORDER_STANDARD define). This is necessary for two main |
| reasons: |
| - users who've already installed Linux won't be screwed. Keep |
| in mind that not everyone is a kernel hacker. |
| - be consistent with the BIOS ordering of the drives. In the |
| BIOS, id 6 is C:, id 0 might be D:. With this scheme, they'd be |
| backwards. This confuses the crap out of those heathens who've |
| got a impure Linux installation (which, <wince>, I'm one of). |
| This whole problem arises because IBM is actually non-standard with |
| the id to BIOS mappings. You'll find, in fdomain.c, a similar |
| comment about a few FD BIOS revisions. The Linux (and apparently |
| industry) standard is that C: maps to scsi id (0,0). Let's stick |
| with that standard. |
| - Since this is technically a branch of my own, I changed the |
| version number to 3.0e-cpb. |
| |
| Jan 17, 1998: (v3.0f) |
| 1) Addition of some statistical info for /proc in proc_info. |
| 2) Taking care of the SCSI-assignment problem, dealed by Chris at Dec 15 |
| 1997. In fact, IBM is right, concerning the assignment of SCSI-devices |
| to driveletters. It is conform to the ANSI-definition of the SCSI- |
| standard to assign drive C: to SCSI-id 6, because it is the highest |
| hardware priority after the hostadapter (that has still today by |
| default everywhere id 7). Also realtime-operating systems that I use, |
| like LynxOS and OS9, which are quite industrial systems use top-down |
| numbering of the harddisks, that is also starting at id 6. Now, one |
| sits a bit between two chairs. On one hand side, using the define |
| IBMMCA_SCSI_ORDER_STANDARD makes Linux assigning disks conform to |
| the IBM- and ANSI-SCSI-standard and keeps this driver downward |
| compatible to older releases, on the other hand side, people is quite |
| habituated in believing that C: is assigned to (0,0) and much other |
| SCSI-BIOS do so. Therefore, I moved the IBMMCA_SCSI_ORDER_STANDARD |
| define out of the driver and put it into Config.in as subitem of |
| 'IBM SCSI support'. A help, added to Documentation/Configure.help |
| explains the differences between saying 'y' or 'n' to the user, when |
| IBMMCA_SCSI_ORDER_STANDARD prompts, so the ordinary user is enabled to |
| choose the way of assignment, depending on his own situation and gusto. |
| 3) Adapted SCSI_IBMMCA_DEV_RESET to the local naming convention, so it is |
| now called IBMMCA_SCSI_DEV_RESET. |
| 4) Optimization of proc_info and its subroutines. |
| 5) Added more in-source-comments and extended the driver description by |
| some explanation about the SCSI-device-assignment problem. |
| - Michael Lang |
| |
| Jan 18, 1998: (v3.0g) |
| 1) Correcting names to be absolutely conform to the later 2.1.x releases. |
| This is necessary for |
| IBMMCA_SCSI_DEV_RESET -> CONFIG_IBMMCA_SCSI_DEV_RESET |
| IBMMCA_SCSI_ORDER_STANDARD -> CONFIG_IBMMCA_SCSI_ORDER_STANDARD |
| - Michael Lang |
| |
| Jan 18, 1999: (v3.1 MCA-team internal) |
| 1) The multiple hosts structure is accessed from every subroutine, so there |
| is no longer the address of the device structure passed from function |
| to function, but only the hostindex. A call by value, nothing more. This |
| should really be understood by the compiler and the subsystem should get |
| the right values and addresses. |
| 2) The SCSI-subsystem detection was not complete and quite hugely buggy up |
| to now, compared to the technical manual. The interpretation of the pos2 |
| register is not as assumed by people before, therefore, I dropped a note |
| in the ibmmca_detect function to show the registers' interpretation. |
| The pos-registers of integrated SCSI-subsystems do not contain any |
| information concerning the IO-port offset, really. Instead, they contain |
| some info about the adapter, the chip, the NVRAM .... The I/O-port is |
| fixed to 0x3540 - 0x3547. There can be more than one adapters in the |
| slots and they get an offset for the I/O area in order to get their own |
| I/O-address area. See chapter 2 for detailed description. At least, the |
| detection should now work right, even on models other than 95. The 95ers |
| came happily around the bug, as their pos2 register contains always 0 |
| in the critical area. Reserved bits are not allowed to be interpreted, |
| therefore, IBM is allowed to set those bits as they like and they may |
| really vary between different PS/2 models. So, now, no interpretation |
| of reserved bits - hopefully no trouble here anymore. |
| 3) The command error, which you may get on models 55, 56, 57, 70, 77 and |
| P70 may have been caused by the fact, that adapters of older design do |
| not like sending commands to non-existing SCSI-devices and will react |
| with a command error as a sign of protest. While this error is not |
| present on IBM SCSI Adapter w/cache, it appears on IBM Integrated SCSI |
| Adapters. Therefore, I implemented a workarround to forgive those |
| adapters their protests, but it is marked up in the statisctis, so |
| after a successful boot, you can see in /proc/scsi/ibmmca/<host_number> |
| how often the command errors have been forgiven to the SCSI-subsystem. |
| If the number is bigger than 0, you have a SCSI subsystem of older |
| design, what should no longer matter. |
| 4) ibmmca_getinfo() has been adapted very carefully, so it shows in the |
| slotn file really, what is senseful to be presented. |
| 5) ibmmca_register() has been extended in its parameter list in order to |
| pass the right name of the SCSI-adapter to Linux. |
| - Michael Lang |
| |
| Feb 6, 1999: (v3.1) |
| 1) Finally, after some 3.1Beta-releases, the 3.1 release. Sorry, for |
| the delayed release, but it was not finished with the release of |
| Kernel 2.2.0. |
| - Michael Lang |
| |
| Feb 10, 1999 (v3.1) |
| 1) Added a new commandline parameter called 'bypass' in order to bypass |
| every integrated subsystem SCSI-command consequently in case of |
| troubles. |
| 2) Concatenated read_capacity requests to the harddisks. It gave a lot |
| of troubles with some controllers and after I wanted to apply some |
| extensions, it jumped out in the same situation, on my w/cache, as like |
| on D. Weinehalls' Model 56, having integrated SCSI. This gave me the |
| descissive hint to move the code-part out and declare it global. Now, |
| it seems to work by far much better an more stable. Let us see, what |
| the world thinks of it... |
| 3) By the way, only Sony DAT-drives seem to show density code 0x13. A |
| test with a HP drive gave right results, so the problem is vendor- |
| specific and not a problem of the OS or the driver. |
| - Michael Lang |
| |
| Feb 18, 1999 (v3.1d) |
| 1) The abort command and the reset function have been checked for |
| inconsistencies. From the logical point of thinking, they work |
| at their optimum, now, but as the subsystem does not answer with an |
| interrupt, abort never finishes, sigh... |
| 2) Everything, that is accessed by a busmaster request from the adapter |
| is now declared as global variable, even the return-buffer in the |
| local checking phase. This assures, that no accesses to undefined memory |
| areas are performed. |
| 3) In ibmmca.h, the line unchecked_isa_dma is added with 1 in order to |
| avoid memory-pointers for the areas higher than 16MByte in order to |
| be sure, it also works on 16-Bit Microchannel bus systems. |
| 4) A lot of small things have been found, but nothing that endangered the |
| driver operations. Just it should be more stable, now. |
| - Michael Lang |
| |
| Feb 20, 1999 (v3.1e) |
| 1) I took the warning from the Linux Kernel Hackers Guide serious and |
| checked the cmd->result return value to the done-function very carefully. |
| It is obvious, that the IBM SCSI only delivers the tsb.dev_status, if |
| some error appeared, else it is undefined. Now, this is fixed. Before |
| any SCB command gets queued, the tsb.dev_status is set to 0, so the |
| cmd->result won't screw up Linux higher level drivers. |
| 2) The reset-function has slightly improved. This is still planed for |
| abort. During the abort and the reset function, no interrupts are |
| allowed. This is however quite hard to cope with, so the INT-status |
| register is read. When the interrupt gets queued, one can find its |
| status immediately on that register and is enabled to continue in the |
| reset function. I had no chance to test this really, only in a bogus |
| situation, I got this function running, but the situation was too much |
| worse for Linux :-(, so tests will continue. |
| 3) Buffers got now consistent. No open address mapping, as before and |
| therefore no further troubles with the unassigned memory segmentation |
| faults that scrambled probes on 95XX series and even on 85XX series, |
| when the kernel is done in a not so perfectly fitting way. |
| 4) Spontaneous interrupts from the subsystem, appearing without any |
| command previously queued are answered with a DID_BAD_INTR result. |
| 5) Taken into account ZP Gus' proposals to reverse the SCSI-device |
| scan order. As it does not work on Kernel 2.1.x or 2.2.x, as proposed |
| by him, I implemented it in a slightly derived way, which offers in |
| addition more flexibility. |
| - Michael Lang |
| |
| Apr 23, 2000 (v3.2pre1) |
| 1) During a very long time, I collected a huge amount of bugreports from |
| various people, trying really quite different things on their SCSI- |
| PS/2s. Today, all these bugreports are taken into account and should be |
| mostly solved. The major topics were: |
| - Driver crashes during boottime by no obvious reason. |
| - Driver panics while the midlevel-SCSI-driver is trying to inquire |
| the SCSI-device properties, even though hardware is in perfect state. |
| - Displayed info for the various slot-cards is interpreted wrong. |
| The main reasons for the crashes were two: |
| 1) The commands to check for device information like INQUIRY, |
| TEST_UNIT_READY, REQUEST_SENSE and MODE_SENSE cause the devices |
| to deliver information of up to 255 bytes. Midlevel drivers offer |
| 1024 bytes of space for the answer, but the IBM-SCSI-adapters do |
| not accept this, as they stick quite near to ANSI-SCSI and report |
| a COMMAND_ERROR message which causes the driver to panic. The main |
| problem was located around the INQUIRY command. Now, for all the |
| mentioned commands, the buffersize, sent to the adapter is at |
| maximum 255 which seems to be a quite reasonable solution. |
| TEST_UNIT_READY gets a buffersize of 0 to make sure, that no |
| data is transferred in order to avoid any possible command failure. |
| 2) On unsuccessful TEST_UNIT_READY, the midlevel-driver has to send |
| a REQUEST_SENSE in order to see, where the problem is located. This |
| REQUEST_SENSE may have various length in its answer-buffer. IBM |
| SCSI-subsystems report a command failure, if the returned buffersize |
| is different from the sent buffersize, but this can be supressed by |
| a special bit, which is now done and problems seem to be solved. |
| 2) Code adaption to all kernel-releases. Now, the 3.2 code compiles on |
| 2.0.x, 2.1.x, 2.2.x and 2.3.x kernel releases without any code-changes. |
| 3) Commandline-parameters are recognized again, even under Kernel 2.3.x or |
| higher. |
| - Michael Lang |
| |
| April 27, 2000 (v3.2pre2) |
| 1) Bypassed commands get read by the adapter by one cycle instead of two. |
| This increases SCSI-performance. |
| 2) Synchronous datatransfer is provided for sure to be 5 MHz on older |
| SCSI and 10 MHz on internal F/W SCSI-adapter. |
| 3) New commandline parameters allow to force the adapter to slow down while |
| in synchronous transfer. Could be helpful for very old devices. |
| - Michael Lang |
| |
| June 2, 2000 (v3.2pre5) |
| 1) Added Jim Shorney's contribution to make the activity indicator |
| flashing in addition to the LED-alphanumeric display-panel on |
| models 95A. To be enabled to choose this feature freely, a new |
| commandline parameter is added, called 'activity'. |
| 2) Added the READ_CONTROL bit for test_unit_ready SCSI-command. |
| 3) Added some suppress_exception bits to read_device_capacity and |
| all device_inquiry occurrences in the driver code. |
| 4) Complaints about the various KERNEL_VERSION implementations are |
| taken into account. Every local_LinuxKernelVersion occurrence is |
| now replaced by KERNEL_VERSION, defined in linux/version.h. |
| Corresponding changes were applied to ibmmca.h, too. This was a |
| contribution to all kernel-parts by Philipp Hahn. |
| - Michael Lang |
| |
| July 17, 2000 (v3.2pre8) |
| A long period of collecting bugreports from all corners of the world |
| now lead to the following corrections to the code: |
| 1) SCSI-2 F/W support crashed with a COMMAND ERROR. The reason for this |
| was, that it is possible to disbale Fast-SCSI for the external bus. |
| The feature-control command, where this crash appeared regularly tried |
| to set the maximum speed of 10MHz synchronous transfer speed and that |
| reports a COMMAND ERROR, if external bus Fast-SCSI is disabled. Now, |
| the feature-command probes down from maximum speed until the adapter |
| stops to complain, which is at the same time the maximum possible |
| speed selected in the reference program. So, F/W external can run at |
| 5 MHz (slow-) or 10 MHz (fast-SCSI). During feature probing, the |
| COMMAND ERROR message is used to detect if the adapter does not complain. |
| 2) Up to now, only combined busmode is supported, if you use external |
| SCSI-devices, attached to the F/W-controller. If dual bus is selected, |
| only the internal SCSI-devices get accessed by Linux. For most |
| applications, this should do fine. |
| 3) Wide-SCSI-addressing (16-Bit) is now possible for the internal F/W |
| bus on the F/W adapter. If F/W adapter is detected, the driver |
| automatically uses the extended PUN/LUN <-> LDN mapping tables, which |
| are now new from 3.2pre8. This allows PUNs between 0 and 15 and should |
| provide more fun with the F/W adapter. |
| 4) Several machines use the SCSI: POS registers for internal/undocumented |
| storage of system relevant info. This confused the driver, mainly on |
| models 9595, as it expected no onboard SCSI only, if all POS in |
| the integrated SCSI-area are set to 0x00 or 0xff. Now, the mechanism |
| to check for integrated SCSI is much more restrictive and these problems |
| should be history. |
| - Michael Lang |
| |
| July 18, 2000 (v3.2pre9) |
| This develop rather quickly at the moment. Two major things were still |
| missing in 3.2pre8: |
| 1) The adapter PUN for F/W adapters has 4-bits, while all other adapters |
| have 3-bits. This is now taken into account for F/W. |
| 2) When you select CONFIG_IBMMCA_SCSI_ORDER_STANDARD, you should |
| normally get the inverse probing order of your devices on the SCSI-bus. |
| The ANSI device order gets scrambled in version 3.2pre8!! Now, a new |
| and tested algorithm inverts the device-order on the SCSI-bus and |
| automatically avoids accidental access to whatever SCSI PUN the adapter |
| is set and works with SCSI- and Wide-SCSI-addressing. |
| - Michael Lang |
| |
| July 23, 2000 (v3.2pre10 unpublished) |
| 1) LED panel display supports wide-addressing in ibmmca=display mode. |
| 2) Adapter-information and autoadaption to address-space is done. |
| 3) Auto-probing for maximum synchronous SCSI transfer rate is working. |
| 4) Optimization to some embedded function calls is applied. |
| 5) Added some comment for the user to wait for SCSI-devices being probed. |
| 6) Finished version 3.2 for Kernel 2.4.0. It least, I thought it is but... |
| - Michael Lang |
| |
| July 26, 2000 (v3.2pre11) |
| 1) I passed a horrible weekend getting mad with NMIs on kernel 2.2.14 and |
| a model 9595. Asking around in the community, nobody except of me has |
| seen such errors. Weired, but I am trying to recompile everything on |
| the model 9595. Maybe, as I use a specially modified gcc, that could |
| cause problems. But, it was not the reason. The true background was, |
| that the kernel was compiled for i386 and the 9595 has a 486DX-2. |
| Normally, no troubles should appear, but for this special machine, |
| only the right processor support is working fine! |
| 2) Previous problems with synchronous speed, slowing down from one adapter |
| to the next during probing are corrected. Now, local variables store |
| the synchronous bitmask for every single adapter found on the MCA bus. |
| 3) LED alphanumeric panel support for XX95 systems is now showing some |
| alive rotator during boottime. This makes sense, when no monitor is |
| connected to the system. You can get rid of all display activity, if |
| you do not use any parameter or just ibmmcascsi=activity, for the |
| harddrive activity LED, existant on all PS/2, except models 8595-XXX. |
| If no monitor is available, please use ibmmcascsi=display, which works |
| fine together with the linuxinfo utility for the LED-panel. |
| - Michael Lang |
| |
| July 29, 2000 (v3.2) |
| 1) Submission of this driver for kernel 2.4test-XX and 2.2.17. |
| - Michael Lang |
| |
| December 28, 2000 (v3.2d / v4.0) |
| 1) The interrupt handler had some wrong statement to wait for. This |
| was done due to experimental reasons during 3.2 development but it |
| has shown that this is not stable enough. Going back to wait for the |
| adapter to be not busy is best. |
| 2) Inquiry requests can be shorter than 255 bytes of return buffer. Due |
| to a bug in the ibmmca_queuecommand routine, this buffer was forced |
| to 255 at minimum. If the memory address, this return buffer is pointing |
| to does not offer more space, invalid memory accesses destabilized the |
| kernel. |
| 3) version 4.0 is only valid for kernel 2.4.0 or later. This is necessary |
| to remove old kernel version dependent waste from the driver. 3.2d is |
| only distributed with older kernels but keeps compatibility with older |
| kernel versions. 4.0 and higher versions cannot be used with older |
| kernels anymore!! You must have at least kernel 2.4.0!! |
| 4) The commandline argument 'bypass' and all its functionality got removed |
| in version 4.0. This was never really necessary, as all troubles were |
| based on non-command related reasons up to now, so bypassing commands |
| did not help to avoid any bugs. It is kept in 3.2X for debugging reasons. |
| 5) Dynamical reassignment of ldns was again verified and analyzed to be |
| completely inoperational. This is corrected and should work now. |
| 6) All commands that get sent to the SCSI adapter were verified and |
| completed in such a way, that they are now completely conform to the |
| demands in the technical description of IBM. Main candidates were the |
| DEVICE_INQUIRY, REQUEST_SENSE and DEVICE_CAPACITY commands. They must |
| be tranferred by bypassing the internal command buffer of the adapter |
| or else the response can be a random result. GET_POS_INFO would be more |
| safe in usage, if one could use the SUPRESS_EXCEPTION_SHORT, but this |
| is not allowed by the technical references of IBM. (Sorry, folks, the |
| model 80 problem is still a task to be solved in a different way.) |
| 7) v3.2d is still hold back for some days for testing, while 4.0 is |
| released. |
| - Michael Lang |
| |
| January 3, 2001 (v4.0a) |
| 1) A lot of complains after the 2.4.0-prerelease kernel came in about |
| the impossibility to compile the driver as a module. This problem is |
| solved. In combination with that problem, some unprecise declaration |
| of the function option_setup() gave some warnings during compilation. |
| This is solved, too by a forward declaration in ibmmca.c. |
| 2) #ifdef argument concerning CONFIG_SCSI_IBMMCA is no longer needed and |
| was entirely removed. |
| 3) Some switch statements got optimized in code, as some minor variables |
| in internal SCSI-command handlers. |
| - Michael Lang |
| |
| 4 To do |
| ------- |
| - IBM SCSI-2 F/W external SCSI bus support in separate mode! |
| - It seems that the handling of bad disks is really bad - |
| non-existent, in fact. However, a low-level driver cannot help |
| much, if such things happen. |
| |
| 5 Users' Manual |
| --------------- |
| 5.1 Commandline Parameters |
| -------------------------- |
| There exist several features for the IBM SCSI-subsystem driver. |
| The commandline parameter format is: |
| |
| ibmmcascsi=<command1>,<command2>,<command3>,... |
| |
| where commandN can be one of the following: |
| |
| display Owners of a model 95 or other PS/2 systems with an |
| alphanumeric LED display may set this to have their |
| display showing the following output of the 8 digits: |
| |
| ------DA |
| |
| where '-' stays dark, 'D' shows the SCSI-device id |
| and 'A' shows the SCSI hostindex, being currently |
| accessed. During boottime, this will give the message |
| |
| SCSIini* |
| |
| on the LED-panel, where the * represents a rotator, |
| showing the activity during the probing phase of the |
| driver which can take up to two minutes per SCSI-adapter. |
| adisplay This works like display, but gives more optical overview |
| of the activities on the SCSI-bus. The display will have |
| the following output: |
| |
| 6543210A |
| |
| where the numbers 0 to 6 light up at the shown position, |
| when the SCSI-device is accessed. 'A' shows again the SCSI |
| hostindex. If display nor adisplay is set, the internal |
| PS/2 harddisk LED is used for media-activities. So, if |
| you really do not have a system with a LED-display, you |
| should not set display or adisplay. Keep in mind, that |
| display and adisplay can only be used alternatively. It |
| is not recommended to use this option, if you have some |
| wide-addressed devices e.g. at the SCSI-2 F/W adapter in |
| your system. In addition, the usage of the display for |
| other tasks in parallel, like the linuxinfo-utility makes |
| no sense with this option. |
| activity This enables the PS/2 harddisk LED activity indicator. |
| Most PS/2 have no alphanumeric LED display, but some |
| indicator. So you should use this parameter to activate it. |
| If you own model 9595 (Server95), you can have both, the |
| LED panel and the activity indicator in parallel. However, |
| some PS/2s, like the 8595 do not have any harddisk LED |
| activity indicator, which means, that you must use the |
| alphanumeric LED display if you want to monitor SCSI- |
| activity. |
| bypass This is obsolete from driver version 4.0, as the adapters |
| got that far understood, that the selection between |
| integrated and bypassed commands should now work completely |
| correct! For historical reasons, the old description is |
| kept here: |
| This commandline parameter forces the driver never to use |
| SCSI-subsystems' integrated SCSI-command set. Except of |
| the immediate assign, which is of vital importance for |
| every IBM SCSI-subsystem to set its ldns right. Instead, |
| the ordinary ANSI-SCSI-commands are used and passed by the |
| controller to the SCSI-devices, therefore 'bypass'. The |
| effort, done by the subsystem is quite bogus and at a |
| minimum and therefore it should work everywhere. This |
| could maybe solve troubles with old or integrated SCSI- |
| controllers and nasty harddisks. Keep in mind, that using |
| this flag will slow-down SCSI-accesses slightly, as the |
| software generated commands are always slower than the |
| hardware. Non-harddisk devices always get read/write- |
| commands in bypass mode. On the most recent releases of |
| the Linux IBM-SCSI-driver, the bypass command should be |
| no longer a necessary thing, if you are sure about your |
| SCSI-hardware! |
| normal This is the parameter, introduced on the 2.0.x development |
| rail by ZP Gu. This parameter defines the SCSI-device |
| scan order in the new industry standard. This means, that |
| the first SCSI-device is the one with the lowest pun. |
| E.g. harddisk at pun=0 is scanned before harddisk at |
| pun=6, which means, that harddisk at pun=0 gets sda |
| and the one at pun=6 gets sdb. |
| ansi The ANSI-standard for the right scan order, as done by |
| IBM, Microware and Microsoft, scans SCSI-devices starting |
| at the highest pun, which means, that e.g. harddisk at |
| pun=6 gets sda and a harddisk at pun=0 gets sdb. If you |
| like to have the same SCSI-device order, as in DOS, OS-9 |
| or OS/2, just use this parameter. |
| fast SCSI-I/O in synchronous mode is done at 5 MHz for IBM- |
| SCSI-devices. SCSI-2 Fast/Wide Adapter/A external bus |
| should then run at 10 MHz if Fast-SCSI is enabled, |
| and at 5 MHz if Fast-SCSI is disabled on the external |
| bus. This is the default setting when nothing is |
| specified here. |
| medium Synchronous rate is at 50% approximately, which means |
| 2.5 MHz for IBM SCSI-adapters and 5.0 MHz for F/W ext. |
| SCSI-bus (when Fast-SCSI speed enabled on external bus). |
| slow The slowest possible synchronous transfer rate is set. |
| This means 1.82 MHz for IBM SCSI-adapters and 2.0 MHz |
| for F/W external bus at Fast-SCSI speed on the external |
| bus. |
| |
| A further option is that you can force the SCSI-driver to accept a SCSI- |
| subsystem at a certain I/O-address with a predefined adapter PUN. This |
| is done by entering |
| |
| commandN = I/O-base |
| commandN+1 = adapter PUN |
| |
| e.g. ibmmcascsi=0x3540,7 will force the driver to detect a SCSI-subsystem |
| at I/O-address 0x3540 with adapter PUN 7. Please only use this method, if |
| the driver does really not recognize your SCSI-adapter! With driver version |
| 3.2, this recognition of various adapters was hugely improved and you |
| should try first to remove your commandline arguments of such type with a |
| newer driver. I bet, it will be recognized correctly. Even multiple and |
| different types of IBM SCSI-adapters should be recognized correctly, too. |
| Use the forced detection method only as last solution! |
| |
| Examples: |
| |
| ibmmcascsi=adisplay |
| |
| This will use the advanced display mode for the model 95 LED alphanumeric |
| display. |
| |
| ibmmcascsi=display,0x3558,7 |
| |
| This will activate the default display mode for the model 95 LED display |
| and will force the driver to accept a SCSI-subsystem at I/O-base 0x3558 |
| with adapter PUN 7. |
| |
| 5.2 Troubleshooting |
| ------------------- |
| The following FAQs should help you to solve some major problems with this |
| driver. |
| |
| Q: "Reset SCSI-devices at boottime" halts the system at boottime, why? |
| A: This is only tested with the IBM SCSI Adapter w/cache. It is not |
| yet prooved to run on other adapters, however you may be lucky. |
| In version 3.1d this has been hugely improved and should work better, |
| now. Normally you really won't need to activate this flag in the |
| kernel configuration, as all post 1989 SCSI-devices should accept |
| the reset-signal, when the computer is switched on. The SCSI- |
| subsystem generates this reset while being initialized. This flag |
| is really reserved for users with very old, very strange or self-made |
| SCSI-devices. |
| Q: Why is the SCSI-order of my drives mirrored to the device-order |
| seen from OS/2 or DOS ? |
| A: It depends on the operating system, if it looks at the devices in |
| ANSI-SCSI-standard (starting from pun 6 and going down to pun 0) or |
| if it just starts at pun 0 and counts up. If you want to be conform |
| with OS/2 and DOS, you have to activate this flag in the kernel |
| configuration or you should set 'ansi' as parameter for the kernel. |
| The parameter 'normal' sets the new industry standard, starting |
| from pun 0, scanning up to pun 6. This allows you to change your |
| opinion still after having already compiled the kernel. |
| Q: Why I cannot find the IBM MCA SCSI support in the config menue? |
| A: You have to activate MCA bus support, first. |
| Q: Where can I find the latest info about this driver? |
| A: See the file MAINTAINERS for the current WWW-address, which offers |
| updates, info and Q/A lists. At this files' origin, the webaddress |
| was: http://www.uni-mainz.de/~langm000/linux.html |
| Q: My SCSI-adapter is not recognized by the driver, what can I do? |
| A: Just force it to be recognized by kernel parameters. See section 5.1. |
| If this really happens, do also send e-mail to the maintainer, as |
| forced detection should be never necessary. Forced detection is in |
| principal some flaw of the driver adapter detection and goes into |
| bugreports. |
| Q: The driver screws up, if it starts to probe SCSI-devices, is there |
| some way out of it? |
| A: Yes, that was some recognition problem of the correct SCSI-adapter |
| and its I/O base addresses. Upgrade your driver to the latest release |
| and it should be fine again. |
| Q: I get a message: panic IBM MCA SCSI: command error .... , what can |
| I do against this? |
| A: Previously, I followed the way by ignoring command errors by using |
| ibmmcascsi=forgiveall, but this command no longer exists and is |
| obsolete. If such a problem appears, it is caused by some segmentation |
| fault of the driver, which maps to some unallowed area. The latest |
| version of the driver should be ok, as most bugs have been solved. |
| Q: There are still kernel panics, even after having set |
| ibmmcascsi=forgiveall. Are there other possibilities to prevent |
| such panics? |
| A: No, get just the latest release of the driver and it should work |
| better and better with increasing version number. Forget about this |
| ibmmcascsi=forgiveall, as also ignorecmd are obsolete.! |
| Q: Linux panics or stops without any comment, but it is probable, that my |
| harddisk(s) have bad blocks. |
| A: Sorry, the bad-block handling is still a feeble point of this driver, |
| but is on the schedule for development in the near future. |
| Q: Linux panics while dynamically assigning SCSI-ids or ldns. |
| A: If you disconnect a SCSI-device from the machine, while Linux is up |
| and the driver uses dynamical reassignment of logical device numbers |
| (ldn), it really gets "angry" if it won't find devices, that were still |
| present at boottime and stops Linux. |
| Q: The system does not recover after an abort-command has been generated. |
| A: This is regrettably true, as it is not yet understood, why the |
| SCSI-adapter does really NOT generate any interrupt at the end of |
| the abort-command. As no interrupt is generated, the abort command |
| cannot get finished and the system hangs, sorry, but checks are |
| running to hunt down this problem. If there is a real pending command, |
| the interrupt MUST get generated after abort. In this case, it |
| should finish well. |
| Q: The system gets in bad shape after a SCSI-reset, is this known? |
| A: Yes, as there are a lot of prescriptions (see the Linux Hackers' |
| Guide) what has to be done for reset, we still share the bad shape of |
| the reset functions with all other low level SCSI-drivers. |
| Astonishingly, reset works in most cases quite ok, but the harddisks |
| won't run in synchonous mode anymore after a reset, until you reboot. |
| Q: Why does my XXX w/Cache adapter not use read-prefetch? |
| A: Ok, that is not completely possible. If a cache is present, the |
| adapter tries to use it internally. Explicitly, one can use the cache |
| with a read prefetch command, maybe in future, but this requires |
| some major overhead of SCSI-commands that risks the performance to |
| go down more than it gets improved. Tests with that are running. |
| Q: I have a IBM SCSI-2 Fast/Wide adapter, it boots in some way and hangs. |
| A: Yes, that is understood, as for sure, your SCSI-2 Fast/Wide adapter |
| was in such a case recognized as integrated SCSI-adapter or something |
| else, but not as the correct adapter. As the I/O-ports get assigned |
| wrongly by that reason, the system should crash in most cases. You |
| should upgrade to the latest release of the SCSI-driver. The |
| recommended version is 3.2 or later. Here, the F/W support is in |
| a stable and reliable condition. Wide-addressing is in addition |
| supported. |
| Q: I get a Ooops message and something like "killing interrupt". |
| A: The reason for this is that the IBM SCSI-subsystem only sends a |
| termination status back, if some error appeared. In former releases |
| of the driver, it was not checked, if the termination status block |
| is NULL. From version 3.2, it is taken care of this. |
| Q: I have a F/W adapter and the driver sees my internal SCSI-devices, |
| but ignores the external ones. |
| A: Select combined busmode in the IBM config-program and check for that |
| no SCSI-id on the external devices appears on internal devices. |
| Reboot afterwards. Dual busmode is supported, but works only for the |
| internal bus, yet. External bus is still ignored. Take care for your |
| SCSI-ids. If combined bus-mode is activated, on some adapters, |
| the wide-addressing is not possible, so devices with ids between 8 |
| and 15 get ignored by the driver & adapter! |
| Q: I have a 9595 and I get a NMI during heavy SCSI I/O e.g. during fsck. |
| A COMMAND ERROR is reported and characters on the screen are missing. |
| Warm reboot is not possible. Things look like quite weired. |
| A: Check the processor type of your 9595. If you have an 80486 or 486DX-2 |
| processor complex on your mainboard and you compiled a kernel that |
| supports 80386 processors, it is possible, that the kernel cannot |
| keep track of the PS/2 interrupt handling and stops on an NMI. Just |
| compile a kernel for the correct processor type of your PS/2 and |
| everything should be fine. This is necessary even if one assumes, |
| that some 80486 system should be downward compatible to 80386 |
| software. |
| Q: Some commands hang and interrupts block the machine. After some |
| timeout, the syslog reports that it tries to call abort, but the |
| machine is frozen. |
| A: This can be a busy wait bug in the interrupt handler of driver |
| version 3.2. You should at least upgrade to 3.2c if you use |
| kernel < 2.4.0 and driver version 4.0 if you use kernel 2.4.0 or |
| later (including all test releases). |
| Q: I have a PS/2 model 80 and more than 16 MBytes of RAM. The driver |
| completely refuses to work, reports NMIs, COMMAND ERRORs or other |
| ambiguous stuff. When reducing the RAM size down below 16 MB, |
| everything is running smoothly. |
| A: No real answer, yet. In any case, one should force the kernel to |
| present SCBs only below the 16 MBytes barrier. Maybe this solves the |
| problem. Not yet tried, but guessing that it could work. To get this, |
| set unchecked_isa_dma argument of ibmmca.h from 0 to 1. |
| |
| 5.3 Bugreports |
| -------------- |
| If you really find bugs in the sourcecode or the driver will successfully |
| refuse to work on your machine, you should send a bug report to me. The |
| best for this is to follow the instructions on the WWW-page for this |
| driver. Fill out the bug-report form, placed on the WWW-page and ship it, |
| so the bugs can be taken into account with maximum efforts. But, please |
| do not send bug reports about this driver to Linus Torvalds or Leonard |
| Zubkoff, as Linus is burried in E-Mail and Leonard is supervising all |
| SCSI-drivers and won't have the time left to look inside every single |
| driver to fix a bug and especially DO NOT send modified code to Linus |
| Torvalds or Alan J. Cox which has not been checked here!!! They are both |
| quite burried in E-mail (as me, sometimes, too) and one should first check |
| for problems on my local teststand. Recently, I got a lot of |
| bugreports for errors in the ibmmca.c code, which I could not imagine, but |
| a look inside some Linux-distribution showed me quite often some modified |
| code, which did no longer work on most other machines than the one of the |
| modifier. Ok, so now that there is maintenance service available for this |
| driver, please use this address first in order to keep the level of |
| confusion low. Thank you! |
| |
| When you get a SCSI-error message that panics your system, a list of |
| register-entries of the SCSI-subsystem is shown (from Version 3.1d). With |
| this list, it is very easy for the maintainer to localize the problem in |
| the driver or in the configuration of the user. Please write down all the |
| values from this report and send them to the maintainer. This would really |
| help a lot and makes life easier concerning misunderstandings. |
| |
| Use the bug-report form (see 5.4 for its address) to send all the bug- |
| stuff to the maintainer or write e-mail with the values from the table. |
| |
| 5.4 Support WWW-page |
| -------------------- |
| The address of the IBM SCSI-subsystem supporting WWW-page is: |
| |
| http://www.uni-mainz.de/~langm000/linux.html |
| |
| Here you can find info about the background of this driver, patches, |
| troubleshooting support, news and a bugreport form. Please check that |
| WWW-page regularly for latest hints. If ever this URL changes, please |
| refer to the MAINTAINERS file in order to get the latest address. |
| |
| For the bugreport, please fill out the formular on the corresponding |
| WWW-page. Read the dedicated instructions and write as much as you |
| know about your problem. If you do not like such formulars, please send |
| some e-mail directly, but at least with the same information as required by |
| the formular. |
| |
| If you have extensive bugreports, including Ooops messages and |
| screen-shots, please feel free to send it directly to the address |
| of the maintainer, too. The current address of the maintainer is: |
| |
| Michael Lang <langa2@kph.uni-mainz.de> |
| |
| 6 References |
| ------------ |
| IBM Corp., "Update for the PS/2 Hardware Interface Technical Reference, |
| Common Interfaces", Armonk, September 1991, PN 04G3281, |
| (available in the U.S. for $21.75 at 1-800-IBM-PCTB or in Germany for |
| around 40,-DM at "Hallo IBM"). |
| |
| IBM Corp., "Personal System/2 Micro Channel SCSI |
| Adapter with Cache Technical Reference", Armonk, March 1990, PN 68X2365. |
| |
| IBM Corp., "Personal System/2 Micro Channel SCSI |
| Adapter Technical Reference", Armonk, March 1990, PN 68X2397. |
| |
| IBM Corp., "SCSI-2 Fast/Wide Adapter/A Technical Reference - Dual Bus", |
| Armonk, March 1994, PN 83G7545. |
| |
| Friedhelm Schmidt, "SCSI-Bus und IDE-Schnittstelle - Moderne Peripherie- |
| Schnittstellen: Hardware, Protokollbeschreibung und Anwendung", 2. Aufl. |
| Addison Wesley, 1996. |
| |
| Michael K. Johnson, "The Linux Kernel Hackers' Guide", Version 0.6, Chapel |
| Hill - North Carolina, 1995 |
| |
| Andreas Kaiser, "SCSI TAPE BACKUP for OS/2 2.0", Version 2.12, Stuttgart |
| 1993 |
| |
| Helmut Rompel, "IBM Computerwelt GUIDE", What is what bei IBM., Systeme * |
| Programme * Begriffe, IWT-Verlag GmbH - Muenchen, 1988 |
| |
| 7 Credits to |
| ------------ |
| 7.1 People |
| ---------- |
| Klaus Grimm |
| who already a long time ago gave me the old code from the |
| SCSI-driver in order to get it running for some old machine |
| in our institute. |
| Martin Kolinek |
| who wrote the first release of the IBM SCSI-subsystem driver. |
| Chris Beauregard |
| who for a long time maintained MCA-Linux and the SCSI-driver |
| in the beginning. Chris, wherever you are: Cheers to you! |
| Klaus Kudielka |
| with whom in the 2.1.x times, I had a quite fruitful |
| cooperation to get the driver running as a module and to get |
| it running with multiple SCSI-adapters. |
| David Weinehall |
| for his excellent maintenance of the MCA-stuff and the quite |
| detailed bug reports and ideas for this driver (and his |
| patience ;-)). |
| Alan J. Cox |
| for his bugreports and his bold activities in cross-checking |
| the driver-code with his teststand. |
| |
| 7.2 Sponsors & Supporters |
| ------------------------- |
| "Hallo IBM", |
| IBM-Deutschland GmbH |
| the service of IBM-Deutschland for customers. Their E-Mail |
| service is unbeatable. Whatever old stuff I asked for, I |
| always got some helpful answers. |
| Karl-Otto Reimers, |
| IBM Klub - Sparte IBM Geschichte, Sindelfingen |
| for sending me a copy of the w/Cache manual from the |
| IBM-Deutschland archives. |
| Harald Staiger |
| for his extensive hardware donations which allows me today |
| still to test the driver in various constellations. |
| Erich Fritscher |
| for his very kind sponsoring. |
| Louis Ohland, |
| Charles Lasitter |
| for support by shipping me an IBM SCSI-2 Fast/Wide manual. |
| In addition, the contribution of various hardware is quite |
| decessive and will make it possible to add FWSR (RAID) |
| adapter support to the driver in the near future! So, |
| complaints about no RAID support won't remain forever. |
| Yes, folks, that is no joke, RAID support is going to rise! |
| Erik Weber |
| for the great deal we made about a model 9595 and the nice |
| surrounding equipment and the cool trip to Mannheim |
| second-hand computer market. In addition, I would like |
| to thank him for his exhaustive SCSI-driver testing on his |
| 95er PS/2 park. |
| Anthony Hogbin |
| for his direct shipment of a SCSI F/W adapter, which allowed |
| me immediately on the first stage to try it on model 8557 |
| together with onboard SCSI adapter and some SCSI w/Cache. |
| Andreas Hotz |
| for his support by memory and an IBM SCSI-adapter. Collecting |
| all this together now allows me to try really things with |
| the driver at maximum load and variety on various models in |
| a very quick and efficient way. |
| Peter Jennewein |
| for his model 30, which serves me as part of my teststand |
| and his cool remark about how you make an ordinary diskette |
| drive working and how to connect it to an IBM-diskette port. |
| Johannes Gutenberg-Universitaet, Mainz & |
| Institut fuer Kernphysik, Mainz Microtron (MAMI) |
| for the offered space, the link, placed on the central |
| homepage and the space to store and offer the driver and |
| related material and the free working times, which allow |
| me to answer all your e-mail. |
| |
| 8 Trademarks |
| ------------ |
| IBM, PS/2, OS/2, Microchannel are registered trademarks of International |
| Business Machines Corporation |
| |
| MS-DOS is a registered trademark of Microsoft Corporation |
| |
| Microware, OS-9 are registered trademarks of Microware Systems |
| |
| 9 Disclaimer |
| ------------ |
| Beside the GNU General Public License and the dependent disclaimers and disclaimers |
| concerning the Linux-kernel in special, this SCSI-driver comes without any |
| warranty. Its functionality is tested as good as possible on certain |
| machines and combinations of computer hardware, which does not exclude, |
| that dataloss or severe damage of hardware is possible while using this |
| part of software on some arbitrary computer hardware or in combination |
| with other software packages. It is highly recommended to make backup |
| copies of your data before using this software. Furthermore, personal |
| injuries by hardware defects, that could be caused by this SCSI-driver are |
| not excluded and it is highly recommended to handle this driver with a |
| maximum of carefulness. |
| |
| This driver supports hardware, produced by International Business Machines |
| Corporation (IBM). |
| |
| ------ |
| Michael Lang |
| (langa2@kph.uni-mainz.de) |