| /* | 
 |  * arch/v850/kernel/ma.c -- V850E/MA series of cpu chips | 
 |  * | 
 |  *  Copyright (C) 2001,02,03  NEC Electronics Corporation | 
 |  *  Copyright (C) 2001,02,03  Miles Bader <miles@gnu.org> | 
 |  * | 
 |  * This file is subject to the terms and conditions of the GNU General | 
 |  * Public License.  See the file COPYING in the main directory of this | 
 |  * archive for more details. | 
 |  * | 
 |  * Written by Miles Bader <miles@gnu.org> | 
 |  */ | 
 |  | 
 | #include <linux/kernel.h> | 
 | #include <linux/init.h> | 
 | #include <linux/mm.h> | 
 | #include <linux/swap.h> | 
 | #include <linux/bootmem.h> | 
 | #include <linux/irq.h> | 
 |  | 
 | #include <asm/atomic.h> | 
 | #include <asm/page.h> | 
 | #include <asm/machdep.h> | 
 | #include <asm/v850e_timer_d.h> | 
 |  | 
 | #include "mach.h" | 
 |  | 
 | void __init mach_sched_init (struct irqaction *timer_action) | 
 | { | 
 | 	/* Start hardware timer.  */ | 
 | 	v850e_timer_d_configure (0, HZ); | 
 | 	/* Install timer interrupt handler.  */ | 
 | 	setup_irq (IRQ_INTCMD(0), timer_action); | 
 | } | 
 |  | 
 | static struct v850e_intc_irq_init irq_inits[] = { | 
 | 	{ "IRQ", 0, 		NUM_MACH_IRQS,	1, 7 }, | 
 | 	{ "CMD", IRQ_INTCMD(0), IRQ_INTCMD_NUM,	1, 5 }, | 
 | 	{ "DMA", IRQ_INTDMA(0), IRQ_INTDMA_NUM,	1, 2 }, | 
 | 	{ "CSI", IRQ_INTCSI(0), IRQ_INTCSI_NUM,	4, 4 }, | 
 | 	{ "SER", IRQ_INTSER(0), IRQ_INTSER_NUM,	4, 3 }, | 
 | 	{ "SR",	 IRQ_INTSR(0),	IRQ_INTSR_NUM, 	4, 4 }, | 
 | 	{ "ST",  IRQ_INTST(0), 	IRQ_INTST_NUM, 	4, 5 }, | 
 | 	{ 0 } | 
 | }; | 
 | #define NUM_IRQ_INITS (ARRAY_SIZE(irq_inits) - 1) | 
 |  | 
 | static struct hw_interrupt_type hw_itypes[NUM_IRQ_INITS]; | 
 |  | 
 | /* Initialize MA chip interrupts.  */ | 
 | void __init ma_init_irqs (void) | 
 | { | 
 | 	v850e_intc_init_irq_types (irq_inits, hw_itypes); | 
 | } | 
 |  | 
 | /* Called before configuring an on-chip UART.  */ | 
 | void ma_uart_pre_configure (unsigned chan, unsigned cflags, unsigned baud) | 
 | { | 
 | 	/* We only know about the first two UART channels (though | 
 | 	   specific chips may have more).  */ | 
 | 	if (chan < 2) { | 
 | 		unsigned bits = 0x3 << (chan * 3); | 
 | 		/* Specify that the relevant pins on the chip should do | 
 | 		   serial I/O, not direct I/O.  */ | 
 | 		MA_PORT4_PMC |= bits; | 
 | 		/* Specify that we're using the UART, not the CSI device.  */ | 
 | 		MA_PORT4_PFC |= bits; | 
 | 	} | 
 | } |